A new thermo‐responsive block copolymer with tunable upper critical solution temperature and lower critical solution temperature in the alcohol/water mixture

The multi‐thermo‐responsive block copolymer of poly[2‐(2‐methoxyethoxy)ethyl methacrylate]‐block‐poly[N‐(4‐vinylbenzyl)‐N,N‐diethylamine] (PMEO₂MA‐b‐PVEA) displaying phase transition at both the lower critical solution temperature (LCST) and the upper critical solution temperature (UCST) in the alcohol/water mixture is synthesized by reversible addition‐fragmentation chain transfer polymerization. The poly[2‐(2‐methoxyethoxy)ethyl methacrylate] (PMEO₂MA) block exhibits the UCST phase transition in alcohol and the LCST phase transition in water, while the poly[N‐(4‐vinylbenzyl)‐N,N‐diethylamine] (PVEA) block shows the UCST phase transition in isopropanol and the LCST phase transition in the alcohol/water mixture. Both the polymer molecular weight and the co‐solvent/nonsolvent exert great influence on the LCST or UCST of the block copolymer. By adjusting the solvent character including the water content and the temperature, the block copolymer undergoes multiphase transition at LCST or UCST, and various block copolymer morphologies including inverted micelles, core‐corona micelles, and corona‐collapsed micelles are prepared. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4399–4412     

Synthesis of a new type of core–shell particle from hyperbranched polyglycerol

Based on hyperbranched polyglycerol (PG), a route to prepare particles with a novel topology was developed. The hydroxyls of PG were converted to trithiocarbonates, and the latter were used to mediate the surface graft polymerization of N,N‐dimethylaminoethyl acrylate. The poly(N,N‐dimethylaminoethyl acrylate) shell was crosslinked by 1,6‐dibromohexane and then parted from the core by the cleavage of trithiocarbonates with sodium borohydride. Novel particles with thiol groups located on the interface between the PG core and poly(N,N‐dimethylaminoethyl acrylate) shell were thus formed. The shell crosslinking could be performed at very high solid contents (2–4%). These polymer particles showed pH‐ and temperature‐dependent solubility. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5458–5464, 2005     

A simple FTIR spectroscopic method for the determination of the lower critical solution temperature of N‐isopropylacrylamide copolymers and related hydrogels

Linear and crosslinked polymers based on N‐isopropylacrylamide (NIPAAm) exhibit unusual thermal properties. Aqueous solutions of poly(N‐isopropylacrylamide) (PNIPAAm) phase‐separate upon heating above a lower critical solution temperature (LCST), whereas related hydrogels undergo a swelling–shrinking transition at an LCST. A linear copolymer made of NIPAAm/acryloxysuccinimide (98/2 mol/mol) and two hydrogels with different hydrophilicities were prepared. Fourier transform infrared (FTIR) spectroscopy was employed to determine the transition temperature and provide insights into the molecular details of the transition via probing of characteristic bands as a function of temperature. The FTIR spectroscopy method described here allowed the determination of the transition temperature for both the linear and crosslinked polymers. The transition temperatures for PNIPAAm and the gel resulting from the crosslinking with polylysine or N,N′‐methylenebisacrylamide (MBA) were in the same range, 30–35 °C. For the gels, the transition temperature increased with the hydrophilicity of the polymer matrix. The spectral changes observed at the LCST were similar for the free chains and the hydrogels, implying a similar molecular reorganization during the transition. The C H stretching region suggests that the N‐isopropyl groups and the backbone both underwent conformational changes and became more ordered upon heating above the LCST. An analysis of the amide I band suggests that the amide groups of the linear polymer were mainly involved in hydrogen bonding with water molecules below the LCST, the chain being flexible and disordered in a water solution. During the transition, around 20% of these intermolecular hydrogen bonds between the polymer and water were broken and replaced by intramolecular hydrogen bonds. Similar changes were also observed at the LCST of a gel crosslinked with MBA. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 907–915, 2000     

Synthesis and self‐assembly of thermosensitive double‐hydrophilic poly(N‐vinylcaprolactam)‐b‐poly(N‐vinyl‐2‐pyrrolidone) diblock copolymers

We report on novel diblock copolymers of poly(N‐vinylcaprolactam) (PVCL) and poly(N‐vinyl‐2‐pyrrolidone) (PVPON) (PVCL‐b‐PVPON) with well‐defined block lengths synthesized by the MADIX/reversible addition‐fragmentation chain transfer (RAFT) process. We show that the lower critical solution temperatures (LCST) of the block copolymers are controllable over the length of PVCL and PVPON segments. All of the diblock copolymers dissolve molecularly in aqueous solutions when the temperature is below the LCST and form spherical micellar or vesicular morphologies when temperature is raised above the LCST. The size of the self‐assembled structures is controlled by the molar ratio of PVCL and PVPON segments. The synthesized homopolymers and diblock copolymers are demonstrated to be nontoxic at 0.1–1 mg mL^?1 concentrations when incubated with HeLa and HEK293 cancer cells for various incubation times and have potential as nanovehicles for drug delivery. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2725–2737     

Micro ATR‐FTIR study of the hydration state of poly(N‐tert‐butylacrylamide‐co‐acrylamide) copolymers during phase transition in aqueous media and in the mixture of water–methanol

Coil‐globule transition of poly(N‐tert‐butylacrylamide‐co‐acrylamide) P(NTBAM‐co‐AM) copolymers is investigated in the aqueous solution and in the mixture of water–methanol by micro ATR‐FTIR spectroscopy technique. In this study the microstructure and its changes in the hydration states of the distinct groups of these copolymers are investigated by micro ATR/FTIR technique. The results showed that by heating the solution above the LCST hydrogen bonding between C?O and water was decreased but the hydrogen bonding between polymeric chains increased, which prove the aggregation of polymer chain during phase separation. The chemical shifts of IR bands are also studied in the mixture of water–methanol. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 356–363, 2010     

Temperature‐induced phase transition of poly(N‐n‐propylacrylamide‐co‐butyl methacrylate‐co‐N,N‐diethylaminoethyl methacrylate)

Terpolymers composed of N‐n‐propylacrylamide (NPAAm), butyl methacrylate (BMA), and N,N‐diethylaminoethyl methacrylate (DEAEMA) were prepared in an attempt to investigate the temperature‐induced phase transition and its mechanism. Poly(NPAAm) showed the lower critical solution temperature (LCST) around 24°C in water. With the incorporation of DEAEMA with NPAAm, the LCST change was characterized by an initial increase. However, the LCST was shifted to the lower temperature at the later stage. This might be explained in terms of hydrophilic/hydrophobic contribution of DEAEMA to the LCST. The swelling behavior of copolymer gel in the various solvents and spin‐lattice relaxation time (T₁) study by NMR strongly suggested the hydrophilic/hydrophobic contribution of DEAEMA to the LCST depending on the local environment. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1407–1411, 1999     

Synthesis of poly[N‐isopropylacrylamide‐g‐poly(ethylene glycol)] with a reactive group at the poly(ethylene glycol) end and its thermosensitive self‐assembling character

Poly[N‐isopropylacrylamide‐g‐poly(ethylene glycol)]s with a reactive group at the poly(ethylene glycol) (PEG) end were synthesized by the radical copolymerization of N‐isopropylacrylamide with a PEG macromonomer having an acetal group at one end and a methacryloyl group at the other chain end. The temperature dependence of the aqueous solutions of the obtained graft copolymers was estimated by light scattering measurements. The intensity of the light scattering from aqueous polymer solutions increased with increasing temperature. In particular, at temperatures above 40°C, the intensity abruptly increased, indicating a phase separation of the graft copolymer due to the lower critical solution temperature (LCST) of the poly(N‐isopropylacrylamide) segment. No turbidity was observed even above the LCST, and this suggested a nanoscale self‐assembling structure of the graft copolymer. The dynamic light scattering measurements confirmed that the size of the aggregate was in the range of several tens of nanometers. The acetal group at the end of the PEG graft chain was easily converted to the aldehyde group by an acid treatment, which was analyzed by ¹H NMR. Such a temperature‐induced nanosphere possessing reactive PEG tethered chains on the surface is promising for new nanobased biomedical materials. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1457–1469, 2006     

An H‐shaped polymer bonding β‐cyclodextrin at branch points: Synthesis and influences of attached β‐cyclodextrins on physical properties

We report on the synthesis of an H‐shaped polymer bonding β‐cyclodextrin (β‐CD) at branch points and influences of attached β‐CD on physical properties. First, a poly(ethylene glycol)(PEG)‐based functional macroinitiator bearing two azidos and four chlorines at chain‐ends (PEG‐2N₃(‐4Cl)) was prepared via terminal modification reactions. Then, PEG‐2N₃(‐4Cl) was applied to initiate the atom transfer radical polymerization of N‐isopropylacrylamide, leading to the synthesis of an H‐shaped block polymer with PEG as the central chain and poly(N‐isopropylacrylamide) (PNIPAM) as side‐arms (PEG‐2N₃(‐4PNIPAM)). Azido groups were at the branch points of the polymer. Finally, the click reaction between PEG‐2N₃(‐4PNIPAM) and alkynyl monosubstituted β‐cyclodextrin (β‐CD) afforded another H‐shaped polymer with two β‐CDs bonding at the polymer branch points (PEG‐2CD(‐4PNIPAM)). The glass transition temperature (T_g) and lower critical solution temperature (LCST) of the H‐shaped polymer increased after the attachment of β‐CD. The self‐assembly and thermal responsive behaviors, as well as the encapsulation behaviors of PEG‐2CD(‐4PNIPAM) were also altered. When temperature was below the LCSTs, PEG‐2N₃(‐2PNIPAM) dissolved in water molecularly, whereas PEG‐2CD(‐4PNIPAM) could self‐assemble into nano‐sized micelles. After the LCST transitions, PEG‐2N₃(‐4PNIPAM) aggregated into micron‐sized unstable particles, whereas PEG‐2CD(‐4PNIPAM) transformed into PNIPAM‐cored nanomicelles. Besides, PEG‐2CD(‐4PNIPAM) can encapsulate doxorubicin below its LCST due to the formation of micelles. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

RAFT cryopolymerizations of N,N‐dimethylacrylamide and N‐isopropylacrylamide in moderately frozen aqueous solution

Aqueous reversible addition‐fragmentation chain transfer (RAFT) cryopolymerizations of N,N‐dimethylacrylamide (DMA) and N‐isopropylacrylamide (NIPAM) with potassium persulfate/sodium ascorbate as redox initiators were performed at ?15 °C. For the homopolymerizations, water‐soluble chain transfer agents (CTAs) of 2‐(1‐carboxy‐1‐methylethyl‐sulfanylthiocarbonylsulfanyl)‐2‐methylpropionic acid and 2‐dodecylsulfanylthiocarbonylsulfanyl‐2‐methylpropionyl‐capped methoxy poly(ethylene glycol) were used. For the sequential block copolymerizations, the obtained trithiocarbonate‐functionalized polymers were used as macro‐CTAs. Although well‐defined homo and block polymers of DMA and NIPAM were synthesized and these RAFT cryopolymerizations were well controlled, their behavior depended on the monomers and CTAs. The polymerization kinetic and polymer structure were studied by proton nuclear magnetic resonance analysis and gel permeation chromatography measurement. Poly(N,N‐dimethylacrylamide)‐based cryogels crosslinked with reductively cleavable disulfide‐containing diacrylamide, N,N′‐bisacryloylcystamine, were synthesized via RAFT cryopolymerization. Scanning electron microscopy observation revealed that the porous structure of cryogels depended on the CTA used. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2009     

Blood cell separation using crosslinkable copolymers containing N,N‐dimethylacrylamide

Amphiphilic copolymers using hydrophilic N,N‐dimethylacrylamide (DMA), hydrophobic methyl methacrylate (MMA) and a crosslinkable monomer, 3‐methacryloyloxypropyl trimethoxysilane (MTSi), were synthesized and evaluated as coating materials for leukocyte removal filters for whole blood. When filters composed of non‐woven fabrics were coated with crosslinked synthesized copolymers, the elution ratios of the copolymers to water were adequately low because of the crosslinking with trimethoxysilane groups of MTSi units in the copolymers. Filters coated with crosslinked poly(DMA‐co‐MTSi) having a 0.96 mole fraction of DMA units showed a 0.35 ± 0.44% platelet permeation ratio and a logarithmic reduction of 4.0 ± 0.68 for leukocytes. On the other hand, an increase in the content of MMA units in the DMA‐containing copolymers improved the permeation ratio of the platelets dramatically. Filters coated with crosslinked poly(DMA‐co‐MMA‐co‐MTSi) containing a 0.39 mole fraction of MMA units and a 0.58 mole fraction of DMA units showed an 86 ± 3.0% platelet permeation ratio and a logarithmic reduction of 2.1 ± 1.2 for leukocytes. This indicates that an adequate content of hydrophobic monomer units, such as MMA units, is necessary for effective platelet permeation. Copyright © 2007 John Wiley & Sons, Ltd.     

Thermally crosslinkable hole‐transporting poly(fluorene‐co‐triphenylamine) for multilayer polymer light‐emitting diodes

This article reports the synthesis and characterization of a novel thermally crosslinkable hole‐transporting poly (fluorene‐co‐triphenylamine) (PFO‐TPA) by Suzuki coupling reaction, followed with its application in the fabrication of multilayer light‐emitting diodes by wet processes. The thermal, photophysical, and electrochemical properties of PFO‐TPA were investigated by differential scanning calorimeter, thermogravimetric analysis, optical spectroscopy, and cyclic voltammetry, respectively. Thermally crosslinked PFO‐TPA, through pendant styryl groups, demonstrates excellent thermal stability (T_d > 400 °C, T_g = 152 °C), solvent resistance, and film homogeneity. Its highest occupied molecular orbital level (?5.30 eV) lies between those of PEDOT:PSS (?5.0 ～ ?5.2 eV) and poly(9,9‐dioctylfluorene) (PFO: ?5.70 eV), forming a stepwise energy ladder to facilitate hole injection. Multilayer device with crosslinked PFO‐TPA as hole‐injection layer (HIL) (ITO/PEDOT:PSS/HIL/PFO/LiF/Ca/Al) was readily fabricated by successive spin‐coating processes, its maximum luminance efficiency (3.16 cd/A) were about six times higher than those without PFO‐TPA layer (0.50 cd/A). The result of hole‐only device also confirmed hole‐injection and hole‐transport abilities of crosslinked PFO‐TPA layer. Consequently, the device performance enhancement is attributed to more balanced charges injection in the presence of crosslinked PFO‐TPA layer. The thermally crosslinkable PFO‐TPA is a promising material for the fabrication of efficient multilayer polymer light‐emitting diodes because it is not only a hole‐transporting polymer but also thermally crosslinkable. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and micellization of PSt‐PNIPAM‐PDMAEMA hetero‐arm star polymer with double thermo‐responsibility

A hetero‐arm star polymer, polystyrene‐poly(N‐isopropylacrylamide)‐ poly(2‐(dimethylamino)ethylmethacrylate) (PSt‐PNIPAM‐PDMAEMA), was synthesized by “clicking” the alkyne group at the junction of PSt‐b‐PNIPAM diblock copolymer onto the azide end‐group of PDMAEMA homopolymer via 1,3‐dipolar cycloaddition. The resultant polymer was characterized by gel permeation chromatography, proton nuclear magnetic resonance spectroscopy and Fourier transform infrared spectroscopy. PSt‐PNIPAM‐PDMAEMA micelles with PSt block as core and PNIPAM and PDMAEMA blocks as shell were formed when adding the copolymer solution in THF into 10 folds of water. Lower critical solution temperature (LCST) of PNIPAM and PDMAEMA homopolymer is 32 °C for PNIPAM and 40 to 50 °C for PDMAEMA, respectively. Upon continuous heating through their LCSTs, PSt‐PNIPAM‐PDMAEMA core‐shell micelles exhibited two‐stage thermally induced collapse. The first‐stage collapse, from 20 to 34 °C, is ascribed to the shrinkage of PNIPAM chains; and the second‐stage collapse, from 38 to 50 °C, is due to the shrinkage of PDMAEMA chains. Dynamic light scattering was used to confirm the double phase transitions. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 786–796, 2009     

Anionic polymerization of N,N‐dialkyl‐2‐methylenebut‐3‐enamide: Effect of alkyl substituents on polymerization behavior

Anionic polymerizations of three 1,3‐butadiene derivatives containing different N,N‐dialkyl amide functions, N,N‐diisopropylamide (DiPA), piperidineamide (PiA), and cis‐2,6‐dimethylpiperidineamide (DMPA) were performed under various conditions, and their polymerization behavior was compared with that of N,N‐diethylamide analogue (DEA), which was previously reported. When polymerization of DiPA was performed at ?78 °C with potassium counter ion, only trace amounts of oligomers were formed, whereas polymers with a narrow molecular weight distribution were obtained in moderate yield when DiPA was polymerized at 0 °C in the presence of LiCl. Decrease in molecular weight and broadening of molecular weight distribution were observed when polymerization was performed at a higher temperature of 20 °C, presumably because of the effect of ceiling temperature. In the case of DMPA, no polymer was formed at 0 °C and polymers with relatively broad molecular weight distributions (M_w/M_n = 1.2) were obtained at 20 °C. The polymerization rate of PiA was much faster than that of the other monomers, and poly(PiA) was obtained in high yield even at ?78 °C in 24 h. The microstructure of the resulting polymers were exclusively 1,4‐ for poly(DMPA), whereas 20–30% of the 1,2‐structure was contained in poly(DiPA) and poly(PiA). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3714–3721, 2010     

Temperature‐induced aggregation of the copolymers of N‐isopropylacrylamide and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate in aqueous solutions

A series of random copolymers of N‐isopropylacrylamide (NIPAM) and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate (AMPS) was synthesized by free‐radical copolymerization. The content of AMPS in the copolymers ranged from 1.1 to 9.6 mol %. The lower critical‐solution temperature (LCST) of copolymers in water increased strongly with an increasing content of AMPS. The influence of polymer concentration on the LCST of the copolymers was studied. For the copolymers with a higher AMPS content, the LCST decreased faster with an increasing concentration than for copolymers with a low content of AMPS. For a copolymer containing 1.1 mol % of AMPS the LCST dropped by about 3 °C when the concentration increased from 1 to 10 g/L, whereas for a copolymer containing 9.6 mol % of AMPS the LCST dropped by about 10 °C in the concentration range from 2 to 10 g/L. It was observed that the ionic strength of the aqueous polymer solution very strongly influences the LCST. This effect was most visible for the copolymer with the highest content of AMPS (9.6 mol %) for which an increase in the ionic strength from 0.2 to 2.0 resulted in a decrease in the LCST by about 27 °C (from 55 to 28 °C), whereas for the copolymer containing 1.1 mol % of AMPS the LCST decreased only by about 6 °C (from 37 to 31 °C) when the ionic strength increased from 0.005 to 0.3. The reactivity ratios for the AMPS and NIPAM monomer pairs were determined using different methods. The values of r_AMPS and r_NIPAM obtained were 11.0–11.6 and 2.1–2.4, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2784–2792, 2001     

Synthesis and characteristics of poly(methyl methacrylate‐co‐methacrylic acid)/poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive semi‐hollow latex particles and their application to drug carriers

In this work, the poly(methyl methacrylate‐co‐methacrylic acid)/poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite semi‐hollow latex particles was synthesized by three processes. The first process was to synthesize the poly(methyl methacrylate‐co‐methacrylic acid) (poly (MMA‐MAA)) copolymer latex particles by the method of soapless emulsion polymerization. The second process was to polymerize methacrylic acid (MAA), N‐isopropylacrylamide (NIPAAm), and crosslinking agent, N,N′‐methylenebisacrylamide, in the presence of poly(MMA‐MAA) latex particles to form the linear poly(methyl methacrylate‐co‐methacrylic acid)/crosslinking poly(methacrylic acid‐co‐N‐isopropylacrylamide) (poly(MMA‐MAA)/poly(MAA‐NIPAAm)) core–shell latex particles with solid structure. In the third process, part of the linear poly(MMA‐MAA) core of core–shell latex particles was dissolved by ammonia to form the poly(MMA‐MAA)/poly(MAA‐NIPAAm) thermosensitive semi‐hollow latex particles. The morphologies of the semi‐hollow latex particles show that there is a hollow zone between the linear poly(MMA‐MAA) core and the crosslinked poly(MAA‐NIPAAm) shell. The crosslinking agent and shell composition significantly influenced the lower critical solution temperature of poly(MMA‐MAA)/poly(MAA‐NIPAAm) semi‐hollow latex particles. Besides, the poly(MMA‐MAA)/poly(MAA‐NIPAAm) thermosensitive semi‐hollow latex particles were used as carriers to load with the model drug, caffeine. The processes of caffeine loaded into the semi‐hollow latex particles appeared four situations, which was different from that of solid latex particles. In addition, the phenomenon of caffeine released from the semi‐hollow latex particles was obviously different from that of solid latex particles. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3441–3451     

Solubilization of C60 by micellization with a thermoresponsive block copolymer in water: Characterization,singlet oxygen generation,and DNA photocleavage

Water‐soluble diblock copolymer, poly(N‐isopropylacrylamide)‐block‐poly(N‐vinyl‐2‐pyrroridone) (PNIPAM_m‐b‐PNVP_n), was found to associate with fullerene (C₆₀), and thus C₆₀ can be solubilized in water. The 63C₆₀/PNIPAM_m‐b‐PNVP_n micelle formed a core‐shell micelle‐like aggregate comprising a C₆₀/PNVP hydrophobic core and a thermoresponsive PNIPAM shell. The C₆₀‐containing polymer micelle formation and its thermoresponsive behavior were characterized using light scattering and ¹H NMR techniques. The hydrodynamic radius (R_h) of the C₆₀‐bound polymer micelle increased with increasing temperature, which was ascribed to the hydrophobic association between dehydrated PNIPAM shells above lower critical solution temperature (LCST). ¹H NMR data suggest that the motion of the PNIPAM block is restricted above LCST due to the dehydration of the PNIPAM shell in water. The generation of singlet oxygen by photosensitization by the C₆₀‐bound polymer micelle was confirmed from photooxidation of 9,10‐anthracenedipropionic acid. Furthermore, DNA was found to be cleaved by visible light irradiation in the presence of the C₆₀‐bound polymer micelle. Therefore, there may be a hope for a pharmaceutical application of the C₆₀‐bound polymer micelle to cancer photodynamic therapy. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Influence of the Z‐group on the RAFT‐mediated polymerizations in nanoreactors

In this work, we showed that the self‐assembly behavior of the macro‐chain transfer agent P(DMA₆₉‐b‐NIPAM₆₀)‐S? (C?S)? S? C₁₂H₂₅ [dodecyltrithiocarbonate (DTTC)] was very different to P(DMA₆₈‐b‐NIPAM₆₂)‐S? (C?S)? S? C₄H₉ [butyltrithiocarbonate (BTTC)], resulting in very different water‐based nanoreactor polymerizations. The DTTC diblock formed small aggregates below the lower critical solution temperature (LCST), which increased slightly above the LCST. This is in contrast to the BTTC diblock, in which unimers existed below the LCST and large aggregates of core–shell nanoreactors were present above the LCST. Polymerization of styrene in the DTTC diblock nanoreactors afforded fast rates of polymerization with the production of narrow molecular weight and particle size distributions. We found a direct relationship between the size and the targeted molecular weight; the greater the targeted the molecular weight the greater the particle size. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Self‐assembly of thermo‐ and pH‐responsive poly(acrylic acid)‐b‐poly(N‐isopropylacrylamide) micelles for drug delivery

Self‐assembled thermo‐ and pH‐responsive poly(acrylic acid)‐b‐poly(N‐isopropylacrylamide) (PAA‐b‐PNIPAM) micelles for entrapment and release of doxorubicin (DOX) was described. Block copolymer PAA‐b‐PNIPAM associated into core‐shell micelles in aqueous solution with collapsed PNIPAM block or protonated PAA block as the core on changing temperature or pH. Complexation of DOX with PAA‐b‐PNIPAM triggered by the electrostatic interaction and release of DOX from the complexes due to the changing of pH or temperature were studied. Complex micelles incorporated with DOX exhibited pH‐responsive and thermoresponsive drug release profile. The release of DOX from micelles was suppressed at pH 7.2 and accelerated at pH 4.0 due to the protonation of carboxyl groups. Furthermore, the cumulative release of DOX from complex micelles was enhanced around LCST ascribed to the structure deformation of the micelles. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5028–5035, 2008     

Dispersion of polystyrene inside polystyrene‐b‐poly(N‐isopropylacrylamide) micelles in water

The addition of mixture of polystyrene‐b‐poly(N‐isopropylacrylamide) (PS‐b‐PNIPAM) and polystyrene homopolymer (h‐PS) in tetrahydrofuran dropwise into water leads to nanoparticles with a PS core and a thermally sensitive PNIPAM shell. The effects of the ratio of the homopolymer to copolymer and temperature on the formation and stabilization of the dispersion were investigated by using a combination of static and dynamic laser light scattering. PNIPAM shell continuously collapses as temperature increases in the range 20–40 °C. Such formed particles are stable even at temperatures much higher than lower critical solution temperature (LCST ～ 32 °C) of PNIPAM. Our results reveal that the area occupied per hydrophilic PNIPAM chain on the hydrophobic PS core remains nearly a constant regardless of the amount of h‐PS in the polymer mixture. This clearly indicates that the surface area occupied per hydrophilic group is a critical parameter for stabilizing particles dispersed in water. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 749–755, 2010     

Doubly photoresponsive and water‐soluble block copolymers: Synthesis and thermosensitivity

We report the synthesis and investigation of a new type of photoresponsive block copolymers (BCPs). They were designed to comprise two water‐soluble polymers containing two different photoisomerizable moieties (either azobenzene and spiropyran or two different azobenzenes), with the two constituting blocks that, when separated, exhibit a lower critical solution temperature (LCST) in water and can shift their LCST in opposite directions upon photoisomerization (decrease of LCST for one polymer and increase for the other). A variety of such doubly photoresponsive BCPs were synthesized using either azobenzene‐ or spiropyran‐containing poly(N,N‐dimethylacrylamide) (PDMA), poly(N‐isopropylacrylamide) (PNIPAM) and poly[methoxydi(ethylene glycol) methacrylate] (PDEGMMA). Their thermal phase transition behaviors in aqueous solution before and after simultaneous photoreactions on the two blocks were investigated in comparison with their constituting blocks, by means of solution transmittance (turbidity) and variable‐temperature ¹H NMR measurements. The results show that BCPs displayed a single LCST whose shift upon two photoisomerizations appeared to be determined by the competing and opposing photoinduced effects on the two blocks. Moreover, optically controlling the relative photoisomerization degrees of trans azobenzene‐to‐cis azobenzene and spiropyran‐to‐merocyanine could be used to tune the LCST of BCP solution. This study demonstrates the potential of exploring a more complex photoreaction scheme to optically control the solution properties of water‐soluble thermosensitive BCPs. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4055–4066, 2010