Quantification issues of trace metals analysis on silicon oxide and nitride films by using VPD‐ICP‐MS and VPD‐GF‐AAS

Vapor phase decomposition (VPD) is a pretreatment technique for collecting trace metal contaminants on the surface of a Si wafer. Such trace metals can be identified and quantified by inductively coupled plasma mass spectrometry (ICP‐MS) or graphite furnace atomic absorption spectroscopy (GF‐AAS). However, the analytical results can be influenced by the Si‐matrix in the VPD samples. This article discusses the approaches to eliminate the interference caused by Si‐matrix. When the thickness of oxide film on wafer surface is less than 100 Å, the quantification results of ICP‐MS analysis will not be affected by Si‐matrix in the VPD samples. Except this, the Si‐matrix must be removed before analysis. An improved heating pretreatment approach has been adopted successfully to eliminate the Si‐matrix. For GF‐AAS analysis, the Si‐matrix will influence the sodium and aluminum analyses. Adding HNO₃ to the graphite furnace tubing after sample injection could also eliminate the interference caused by the Si‐matrix. The method detection limits (MDLs) of VPD‐GF‐AAS and VPD‐ICP‐MS range from 0.04 to 0.55 × 10¹⁰ atoms cm^?2 and 0.05 to 1.73 × 10⁹ atoms cm^?2, respectively. Copyright © 2008 John Wiley & Sons, Ltd.     

Summary of ISO/TC 201 Standard: X ISO 17560:2002—Surface chemical analysis—Secondary ion mass spectrometry—Method for depth profiling of boron in silicon

This International Standard specifies a secondary ion mass spectrometric method using magnetic‐sector or quadrupole mass spectrometers for depth profiling of boron in silicon, and using stylus profilometry or optical interferometry for depth calibration. This method is applicable to single‐crystal, polycrystal or amorphous silicon specimens with boron atomic concentrations between 1 × 10¹⁶ and 1 × 10²⁰ atoms cm^?3, and to the crater depth of 50 nm or deeper. Optical interferometry is generally applicable to crater depths in the range 0.5–5 µm. Copyright © 2004 John Wiley & Sons, Ltd.     

Rolling‐Circle Amplification Detection of Thrombin Using Surface‐Enhanced Raman Spectroscopy with Core‐Shell Nanoparticle Probe

An ultrasensitive surface‐enhanced Raman spectroscopy (SERS) sensor based on rolling‐circle amplification (RCA)‐increased “hot‐spot” was developed for the detection of thrombin. The sensor contains a SERS gold nanoparticle@Raman label@SiO₂ core‐shell nanoparticle probe in which the Raman reporter molecules are sandwiched between a gold nanoparticle core and a thin silica shell by a layer‐by‐layer method. Thrombin aptamer sequences were immobilized onto the magnetic beads (MBs) through hybridization with their complementary strand. In the presence of thrombin, the aptamer sequence was released; this allowed the remaining single‐stranded DNA (ssDNA) to act as primer and initiate in situ RCA reaction to produce long ssDNAs. Then, a large number of SERS probes were attached on the long ssDNA templates, causing thousands of SERS probes to be involved in each biomolecular recognition event. This SERS method achieved the detection of thrombin in the range from 1.0×10^?12 to 1.0×10^?8 M and a detection limit of 4.2×10^?13 M , and showed good performance in real serum samples.     

A Sensitive Fluorescence Quenching Method for the Determination of Iron( Ⅱ） with 1,10-Phenanthroline

A sensitive and selective fluorescence quenching method for the determination of Fe²⁺ with 1,10‐phenanthroline was developed. The fluorescence intensity of 1,10‐phenanthroline at λ_ex of 266 run and λ_em of 365 nm was constant in the range of pH 4.0 to 10.0 and decreased linearly upon addition of Fe²⁺ to its solution. This decrease was mainly due to a static quenching effect caused by the formation of a non‐fluorescent complex of Fe²⁺ with 1, 10‐phenanthroline. The total amount of iron was determined by using hydroxylamine hydrochloride to reduce Fe³⁺ to Fe²⁺. The linear range was from 5.0 × 10–⁷ to 2.0 × 10–⁵ mol/L with a detection limit of 2.4 × 10–⁸ mol/L at 3s?. The quenching constant of Fe²⁺ to 1,10‐phenanthroline was calculated to be (5.70 × 0.05) × 10⁴ L/mol at 25 °C. Effects of foreign ions on the determination of Fe²⁺ were investigated. The results of the new method for the determination of iron in tap water and natural water samples were in good agreement with those obtained by graphite atomic absorption spectrometry.     

Selective Electroanalysis of Ascorbic Acid Using a Nickel Hexacyanoferrate and Poly(3,4‐ethylenedioxythiophene) Hybrid Film Modified Electrode

The mixed‐valent nickel hexacyanoferrate (NiHCF) and poly(3,4‐ethylenedioxythiophene) (PEDOT) hybrid film (NiHCF‐PEDOT) was prepared on a glassy carbon electrode (GCE) by multiple scan cyclic voltammetry. The films were characterized using atomic force microscopy, field emission scanning electron microscopy, energy dispersive spectroscopy, X‐ray diffraction, and electrochemical impedance spectroscopy (AC impedance). The advantages of these films were demonstrated for the detection of ascorbic acid (AA) using cyclic voltammetry and amperometric techniques. The electrocatalytic oxidation of AA at different electrode surfaces, such as the bare GCE, the NiHCF/GCE, and the NiHCF‐PEDOT/GCE modified electrodes, was determined in phosphate buffer solution (pH 7). The AA electrochemical sensor exhibited a linear response from 5×10⁻⁶ to 1.5×10⁻⁴ M (R²=0.9973) and from 1.55×10⁻⁴ to 3×10⁻⁴ M (R²=0.9983), detection limit=1×10⁻⁶ M, with a fast response time (3 s) for AA determination. In addition, the NiHCF‐PEDOT/GCE was advantageous in terms of its simple preparation, specificity, stability and reproducibility.     

Direct Time‐Domain Observation of Conformational Relaxation in Gas‐Phase Cold Collisions

Cooling molecules in the gas phase is important for precision spectroscopy, cold molecule physics, and physical chemistry. Measurements of conformational relaxation cross sections shed important light on potential energy surfaces and energy flow within a molecule. However, gas‐phase conformational cooling has not been previously observed directly. In this work, we directly observe conformational dynamics of 1,2‐propanediol in cold (6 K) collisions with atomic helium using microwave spectroscopy and buffer‐gas cooling. Precise knowledge and control of the collisional environment in the buffer‐gas allows us to measure the absolute collision cross‐section for conformational relaxation. Several conformers of 1,2‐propanediol are investigated and found to have relaxation cross‐sections with He ranging from σ=4.7(3.0)×10^?18 cm² to σ>5×10^?16 cm². Our method is applicable to a broad class of molecules and could be used to provide information about the potential energy surfaces of previously uninvestigated molecules.     

A New Voltammetric Sensor for Hydrazine Based on Michael Addition Reaction Using 1‐Amino‐2‐naphtol‐4‐sulfonic Acid

In this paper, voltammetric determination of hydrazine was investigated by 1‐amino‐2‐naphtol‐4‐sulfonic acid (ANSA) at the surface of carbon paste electrode (CPE) using cyclic voltammetry (CV) and double potential step chronoamperometry. Results showed that in pH 7.00, hydrazine participates in Michael addition reaction with ANSA and the anodic peak potential of hydrazine shifted to 726 mV less positive than CPE in absence of ANSA, this value is unique compared with other research works. Also, the value of rate constant for the oxidation of hydrazine was calculated 8.3 × 10⁴ cm³ mol^‐1 s^‐1 and the diffusion coefficient of ANSA at the surface of CPE was determined 7.3 × 10^‐7 cm² s^‐1. A linear correlation between Ip and hydrazine concentration in the ranges, from 5 × 10^‐5 mol/L to 2.5 × 10^‐2 mol/L with CV method was obtained and the detection limit was found as 4.3 × 10^‐5 mol/L.     

Thermal Behaviors of 2‐(Dinitromethylene)‐1,3‐diazacycloheptane (DNDH)

2‐(Dinitromethylene)‐1,3‐diazacycloheptane (DNDH) was prepared by the reaction of 1,1‐diamino‐2,2‐dinitroethylene (FOX‐7) with 1,4‐diaminoethane in NMP. Thermal decomposition behavior of DNDH was studied under the non‐isothermal conditions with DSC method, and presents only one intensely exothermic decomposition process. The kinetic equation of the decomposition reaction is dα/dT=10^33.88×3α^2/3exp(−3.353×10⁵/RT)/β. The critical temperature of thermal explosion is 215.97°C. Specific heat capacity of DNDH was studied with micro‐DSC method and theoretical calculation method, and the molar heat capacity is 215.40 J·mol⁻¹·K⁻¹ at 298.15 K. Adiabatic time‐to‐explosion was calculated to be 92.07 s. DNDH has same thermal stability to FOX‐7.     

Electrochemical Characterization of Gold 6‐Amino‐2‐mercaptobenzothiazole Self‐Assembled Monolayer for Dopamine Detection in Pharmaceutical Samples

A new sensor, gold‐6‐amino‐2‐mercaptobenzothiazole (6A2MBT), was fabricated via a self‐assembly procedure. Electrochemical properties of the monolayer were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The modified electrode showed excellent antifouling property against the oxidation products of DA, allowed us to construct a dynamic calibration curve with two linear parts, 1.00×10^?6 to 3.72×10^?4 and 3.72×10^?4 to 6.42×10^?4 M DA, with correlation coefficients of 0.997 and 0.992 and a detection limit of 1.57×10^?7 M DA by using differential pulse voltammetry (DPV), respectively. Finally, the performance of the Au‐6A2MBT modified electrode was successfully tested for electrochemical detection of DA in a pharmaceutical sample.     

Analytical Applications of 2,6‐Diacetylpyridine‐bis‐4‐phenyl‐3‐thiosemicarbazone (2,6‐DAPBPTSC): Determination of Cd(II) in Foods and Water Samples

To the determination of trace amount of Cd(II) present in food and water samples, a selective and extractive spectrophotometric method were developed with 2,6‐diacetylpyridine‐bis‐4‐phenyl‐3‐thiosemicarbazone as a complexing agent. The yellowish orange colored metal complex, Cd(II)‐2,6‐DAPBPTSC with 1:1 (M:L) composition was extracted in to cyclohexanol at pH 9.5 and was shows maximum absorbance at λ_max 390 nm. This method obeys Beer's law in the range of 1.12‐11.25 ppm with 0.972 correlation coefficient of Cd(II)‐2,6‐DAPBPTSC complex, which is indicates linearity between the two variables. The molar absorptivity and sandell's sensitivity were found to be 6.088 × 10⁴ L mol^?1 cm^?1 and 0.0018 μg cm^?2, respectively. The instability constant calculated from Asmus' method (1.447 × 10^?4)at room temperature. The precision and accuracy of the method were checked by relative standard deviation (n = 5), 0.929 and its detection limit, 0.0060 μg mL^?1. The interfering effects of various cations and anions were also studied. The proposed method was successfully applied to the determination of Cd(II) in foods and water samples, and was evaluated its performance in terms of Student ‘t’ test and Variance ‘f’ test, which indicates the significance of present method. The inter comparison of the experimental values, using atomic absorption spectrometer (AAS), was also repoted.     

Electrocatalytic Oxidation and Voltammetric Determination of Hydrazine on the Tetrabromo‐p‐Benzoquinone Modified Carbon Paste Electrode

The electrochemical properties of hydrazine studied at the surface of a carbon paste electrode spiked with p‐bromanil (tetrabromo‐p‐benzoquinone) using cyclic voltammetry (CV), double potential‐step chronoamperometry and differential pulse voltammetry (DPV) in aqueous media. The results show this quinone derivative modified carbon paste electrode, can catalyze the hydrazine oxidation in an aqueous buffered solution. It has been found that under the optimum conditions (pH 10.00), the oxidation of hydrazine at the surface of this carbon paste modified electrode occurs at a potential of about 550 mV less positive than that of a bar carbon paste electrode. The electrocatalytic oxidation peak current of hydrazine showed a linear dependent on the hydrazine concentrations and linear analytical curves were obtained in the ranges of 6.00×10^?5 M–8.00×10^?3 M and 7.00×10^?6 M–8.00×10^?4 M of hydrazine concentration with CV and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 3.6×10^?5 M and 5.2×10^?6 M by CV and DPV methods. This method was also used for the determination of hydrazine in the real sample (waste water of the Mazandaran wood and paper factory) by standard addition method.     

Synthesis of New Reagent 2,6‐Diacetylpyridine Bis‐4‐Phenyl‐3‐Thiosemicarbazone (2,6‐DAPBPTSC): Selective,Sensitive and Extractive Spectrophotometric Determination of Co(II) in Vegetable,Soil, Pharmaceutical and Alloy Samples

New synthesized reagent 2,6‐diacetylpyridine bis‐4‐phenyl‐3‐thiosemicarbazone (2,6‐DAPBPTSC) is proposed as a sensitive and selective analytical reagent for the extractive spectrophotometric determination of cobalt(II). Cobalt(II) forms a reddish brown colored complex with 2,6‐DAPBPTSC, which is extracted into isoamylalcohol, under optimum conditions. The maximum absorption of the isoamylalcohol extract is measured at 400 nm. Beer's law is applied in the range 0.6‐6.0 ppm of cobalt(II). The molar absorptivity and Sandell's sensitivity of the complex is calculated as 2.2 × 10⁴ L mol^?1 cm^?1 and 2.68 × 10^?3 μg cm^?2, respectively. An adequate linearity with a correlation coefficient value of 0.969 is obtained for the Co(II)‐2,6‐DAPBPTSC complex. The instability constant of the complex, calculated from Asmus' method is 3.75 × 10^?4 The precision and accuracy of the method is checked with calculation of relative standard deviation (n = 5), 0.388 and the detection limit a value is 0.0028 μg mL^?1. The method is successfully employed for the determination of cobalt(II) in real samples, such as vegetables, soil, water samples, standard alloy samples, and the performance of the present method was evaluated in terms of Student ‘t’ test and Variance ‘f’ test, which indicates the significance of the present method is an inter comparison of the experimental values, using atomic absorption spectrometer (AAS).     

Development and validation of a LC method for the separation and determination of the anticancer‐active FeIII(4‐methoxy‐salophene) using the new second‐generation monolith

LC method with the newly introduced second‐generation monolithic silica RP‐18e column has been developed for the separation of Fe^III(salophene) and four methoxy‐substituted Fe^III(salophene) complexes. The method has been validated for the quantitation of Fe^III(4‐OMe‐salophene), a highly active anticancer substance in vitro, bound to serum albumin. Our routinely used high‐resolution continuum‐source atomic absorption spectroscopy method based on the determination of the central iron atom was unsuitable in this case because serum originally contains significant amounts of iron as revealed by a blank sample of serum albumin. The developed LC method depends on detecting the whole complex rather than the bound iron. Two morphologically different first‐ and second‐generation HPLC monolithic columns have been compared for this purpose. The newly introduced second‐generation monolithic silica column Chromolith® HighResolution RP‐18e column (100 × 4.6 mm, Merck) separated the mixture successful within 13 min. A mobile phase consisting of 25 mM phosphate buffer pH 3/methanol (60:40, v/v) was used at a flow rate of 1 mL/min. The dynamic linear working range of the calibration curve for Fe^III(4‐OMe‐salophene) was found to be between 1 and 200 μg/mL. Detection and quantitation limits were 0.3 and 1 μg/mL, respectively.     

Electrochemical Behavior of Herbal Antitumor Drug Aloe‐Emodin at Carbon‐Coated Nickel Magnetic Nanoparticles Modified Glassy Carbon Electrode

The electrochemical behavior of aloe‐emodin (AE), an important herbal antitumor drug, was investigated at a carbon‐coated nickel magnetic nanoparticles modified glassy carbon electrode (CNN/GCE). A couple of well‐defined redox peaks was obtained. Some electrochemical parameters of AE at a CNN/GCE, such as the charge number, exchange current density, standard heterogeneous rate constant, were measured. The square wave voltammetry (SWV) response of AE was linear with the concentration over two concentration intervals viz. 6.24×10^?9?1.13×10^?6 M and 1.13×10^?6?1.23×10^?5 M, with a detection limit of 2.08 nM. A fast, simple and sensitive detection and analysis of AE was developed.     

X‐Ray Photoelectron Spectroscopy and Electron Microscopy of Hydralazinium Ion‐Selective Electrode Membrane's Surface

New hydralazinium (Hz) plastic membrane electrodes of either conventional or coated‐wire type were constructed based on incorporation of Hz‐phosphotungstate (Hz‐PT) ion associate or Hz‐reineckate (Hz‐Rn) ion‐pair in poly(vinyl chloride) membranes. The (Hz‐PT)‐based electrodes required 30 minutes conditioning time to exhibit nearly Nernstian response over the concentration range 1.58×10^?5–1.7×10^?2 M HzCl. They also showed life span of 17 days, working pH range of 3.2 to 9.4 and high selectivity for Hz towards Na⁺, K⁺, Mg²⁺ and Ca²⁺. The electrodes have not lost their efficiency at temperatures elevated up to 60 °C. They were successfully employed to assaying HzCl in a pharmaceutical preparation. The electrode containing (Hz‐Rn) ion‐pair required 30 minutes conditioning time to show response for Hz over the concentration range 2.5×10^?5–5.6×10^?2 M. The life span of the electrode was only 8 h. X‐ray photoelectron spectroscopy was applied to investigate the effect of prolonged soaking on the membrane's surface of both types of electrodes. The surfaces of fresh and expired membranes containing Hz‐PT were also examined by electron microscopy. The results indicated that the limitation of the life span of plastic membrane electrodes is attributed to leaching of the ion exchanger from the membrane to the test solution in addition to deformation at the surface of the expired electrode.     

Sol—Gel Derived Carbon Ceramic Electrode Bulk—Modified with Tris（1,10—phenanthroline—5,6—dione） iron （Ⅱ）Hexafluorophosphate and Its Use as an Amperometric Iodate Sensor

A surface‐renewable tris(1, 10‐phenanthroline‐5, 6‐dione) iron (D) hexafluorophosphate (FePD) modified carbon ceramic electrode was constructed by dispersing FePD and graphite powder in methyltrimethoxysilane (MTMOS) based gels. The FePD‐modified electrode presented pH‐dependent voltammetric behavior, and its peak currents were diffusion‐controlled in 0.1 mol/L Na₂SO₄ + H₂SO₄ solution (pH = 0.4). In the presence of iodate, dear electrocatalytic reduction waves were observed and thus the chemically modified electrode was used as an amperometric sensor for iodate in common salt. The linear range, sensitivity, detection limit and response time of the iodate sensor were 5 × 10^?6–1 × 10^?2 mol/L, 7.448 μA·L/ mmol, 1.2 × 10^?6 mol/L and 5 s, respectively. A distinct advantage of this sensor is its good reproducibility of surface‐renewal by simple mechanical polishing.     

Interaction of water‐soluble tetrakis‐(1‐methyl‐4‐pyridiniyl)‐porphyrin and CdS naonoparticles

The interaction between positively charged porphyrin TMPyP(4) (tetrakis‐(1‐methyl‐4‐pyridiniyl) porphyrin) and negatively charged surface of colloidal CdS nanoparticles has been studied by absorption spectrum, fluorescence spectroscopy, and time‐correlated single‐photon‐counting methods. Addition of CdS colloid to a TMPyP(4) solution leads to TMPyP(4) adsorption onto the surface of CdS colloid with an apparent association constant of 4643 L/mol. This adsorption results in distinct changes in absorption spectrum of TMPyP (4) and the quenching of its′ fluorescence, but the biexponential fluorescence decay changes hardly. Nearly 90% of the fluorescence of 5 × 10^?6 mol/L TMPyP(4) can be quenched with 1.5 × 10^?4 mol/L CdS colloid. These spectral changes are attributed to the formation of a certain form complex TMPyP(4)‐CdS.     

Thermo‐stable 2‐(arylimino)benzylidene‐9‐arylimino‐5,6,7,8‐tetrahydro cyclohepta[b]pyridyliron(II) precatalysts toward ethylene polymerization and highly linear polyethylenes

A series of 2‐(arylimino)benzylidene‐9‐arylimino‐5,6,7,8‐tetrahydrocyclohepta[b] pyridyliron(II) chlorides was synthesized and characterized using FT‐IR and elemental analysis, and the molecular structures of complexes Fe3 and Fe4 have been confirmed by the single‐crystal X‐ray diffraction as a pseudo‐square‐pyramidal or distorted trigonal‐bipyramidal geometry around the iron core. On activation with methylaluminoxane (MAO) or modified methylaluminoxane (MMAO), all iron precatalysts exhibited high activities toward ethylene polymerization with a marvelous thermo‐stability and long lifetime. The Fe4 /MAO system showed highest activity of 1.56 × 10⁷ gPE·mol^?1(Fe)·h^?1 at 70 °C, which is one of the highest activities toward ethylene polymerization by iron precatalysts. Even up to 80 °C, Fe3 /MAO system still persist high activity as 6.87 × 10⁶ g(PE)·mol^?1(Fe)·h^?1, demonstrating remarkable thermal stability for industrial polymerizations (80–100 °C). This was mainly attributing to the phenyl modification of the framework of the iron precatalysts. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 830–842     

Electro‐optical properties of electropolymerized poly(3‐hexylthiophene)/carbon nanotube composite thin films

3‐hexylthiophene was electropolymerized on a carbon nanotube (CNT)‐laden fluorine‐doped tin oxide substrate. Scanning electron microscopy and Raman spectroscopy revealed that the polymer was infused throughout the thickness of the 150‐nm thick CNT mat, resulting in a conducting composite film with a dense CNT network. The electropolymerized poly(3‐hexylthiophene) (e‐P3HT)/CNT composites exhibited photoluminescence intensity quenching by as much as 92% compared to the neat e‐P3HT, which provided evidence of charge transfer from the polymer phase to the CNT phase. Through‐film impedance and J‐V measurements of the composites gave a conductivity (σ) of 1.2 × 10^?10 S cm^?1 and zero‐field mobility (μ₀) of 8.5 × 10^?4 cm² V^?1 s^?1, both of which were higher than those of neat e‐P3HT films (σ = 9.9 × 10^?12 S cm^?1, μ₀ = 3 × 10^?5 cm² V^?1 s^?1). In electropolymerized samples, the thiophene rings were oriented in the (010) direction (thiophene rings parallel to substrate), which resulted in a broader optical absorbance than for spin coated samples, however, the lack of long‐range conjugation caused a blueshift in the absorbance maximum from 523 nm for unannealed regioregular P3HT (rr‐P3HT) to 470 nm for e‐P3HT. Raman spectroscopy revealed that π‐π stacking in e‐P3HT was comparable to that in rr‐P3HT and significantly higher than in regiorandom P3HT (ran‐P3HT) as shown by the principal Raman peak shift from 1444 to 1446 cm^?1 for e‐P3HT and rr‐P3HT to 1473 cm^?1 for ran‐P3HT. This work demonstrates that these polymer/CNT composites may have interesting properties for electro‐optical applications. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1269–1275, 2011     

1-氨基-1-肼基-2,2-二硝基乙烯（AHDNE）的非等温分解动力学，比热容和绝热至爆时间研究

利用DSC和TG/DTG法研究了1-氨基-1-肼基-2,2-二硝基乙烯（AHDNE）热分解行为及分解动力学,第一热分解过程的动力学方程为： ,其热爆炸临界温度为98.16 ºC。同时,利用微量热法测定了AHDNE的比热容,298.15K时的标准摩尔比热容为211.86 J•mol-1•K-1。计算得到了AHDNE的绝热至爆时间为59.21 s。AHDNE是不稳定的,其热稳定性远低于母体化合物FOX-7。