Photopolymerization of ternary thiol–ene/acrylate systems: Film and network properties

Photocurable, ternary‐component mixtures of a 1:1 molar multifunctional thiol–ene (trithiol and triallyl ether) blend and a 16‐functional acrylate based monomer have been photopolymerized, and the final film properties of the ternary crosslinked networks have been measured. The photopolymerization kinetics, morphology, and mechanical and physical properties of the films have been investigated with real‐time infrared, atomic force microscopy, and dynamic mechanical analysis. The photopolymerization process is a combination of acrylate homopolymerization and copolymerizations of thiol with allyl ether and acrylate functionalities. The tan δ peaks of the photopolymerized ternary systems are relatively narrow and tunable over a large temperature range. The morphology is characterized by a distinct phase‐separated nanostructure. The photocured thiol–ene/acrylate ternary systems can be made to exhibit good mechanical properties with enhanced energy absorption at room temperature by the appropriate selection of each component concentration. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 822–829, 2007.     

Photopolymerization behavior in nanocomposites formed with thiol–acrylate and polymerizable organoclays

Because of the inherent characteristics of the thiol–ene step growth mechanism in preparation of thiol–ene photopolymer clay nanocomposites, the ratio between thiol and ene functional groups at and near the organoclay surfaces may have a significant effect on the polymerization behavior. This study investigates the influence of monomer composition and the type of polymerizable organoclay on thiol–acrylate photopolymerization behavior in preparation of photocurable clay nanocomposite systems. To this end, two types of polymerizable organoclays with acrylate or thiol functional group on the clay surfaces were compared in monomer compositions with different polarity and functionality. Real‐time infrared spectroscopy was used to characterize polymerization behavior in conjunction with photo‐DSC. The degree of clay exfoliation was evaluated using small angle X‐ray scattering and correlated with photopolymerization behavior. Higher chemical compatibility of components induced enhanced clay exfoliation resulting in increase in photopolymerization rate. By affecting the stoichiometric ratio of functional groups in the clay gallery, thiolated organoclays enhance thiol–ene reaction, whereas acrylated organoclays encourage acrylate homopolymerization. In addition, inducing more propagating thiyl radicals on the organoclay surfaces by increasing functionality of thiol monomer also facilitates thiol–ene copolymerization, whereas the increase of acrylate functionality reduces final thiol conversion. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Ultrathin gradient films using thiol‐ene polymerizations

The application of surface‐attached, thiol‐ene polymer films for controlling material properties in a gradient fashion across a surface was investigated. Thiol‐ene films were attached to the surface by first depositing a thiol‐terminated self‐assembled monolayer and performing a thiol‐ene photopolymerization reaction on the surface. Property gradients were created either by creating and modifying a gradient in the surface thiol density in the SAM or by changing the polymerization conditions or both. Film thickness was modified across the substrate by changing either the density of the anchoring thiol functional groups or by changing the reaction conditions such as exposure time. Thicker films (1–11 nm) were obtained by polymerizing acrylate polymer brushes from the surface with varying exposure time (0–60 s). The two factors, that is, the surface thiol density and the exposure time, were combined in orthogonal directions to obtain thiol‐ene films with a two‐dimensional thickness gradient with the maximum thickness being 4 nm. Finally, a thiol‐acrylate Michael type addition reaction was used to modify the surface thiol density gradient with the cell‐adhesive ligand, Arg‐Gly‐Asp‐Ser (RGDS), which subsequently yielded a gradient in osteoblast density on the surface. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 7027–7039, 2006     

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions as a route to well‐defined mono and bis end‐functionalized poly(N‐isopropylacrylamide)

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used as a facile and quantitative method for modifying end‐groups on an N‐isopropylacrylamide (NIPAm) homopolymer. A well‐defined precursor of polyNIPAm (PNIPAm) was prepared via reversible addition‐fragmentation chain transfer (RAFT) polymerization in DMF at 70 °C using the 1‐cyano‐1‐methylethyl dithiobenzoate/2,2′‐azobis(2‐methylpropionitrile) chain transfer agent/initiator combination yielding a homopolymer with an absolute molecular weight of 5880 and polydispersity index of 1.18. The dithiobenzoate end‐groups were modified in a one‐pot process via primary amine cleavage followed by phosphine‐mediated nucleophilic thiol‐ene click reactions with either allyl methacrylate or propargyl acrylate yielding ene and yne terminal PNIPAm homopolymers quantitatively. The ene and yne groups were then modified, quantitatively as determined by ¹H NMR spectroscopy, via radical thiol‐ene and radical thiol‐yne reactions with three representative commercially available thiols yielding the mono and bis end functional NIPAm homopolymers. This is the first time such sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used in polymer synthesis/end‐group modification. The lower critical solution temperatures (LCST) were then determined for all PNIPAm homopolymers using a combination of optical measurements and dynamic light scattering. It is shown that the LCST varies depending on the chemical nature of the end‐groups with measured values lying in the range 26–35 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3544–3557, 2009     

Kinetics of thiol–ene and thiol–acrylate photopolymerizations with real‐time fourier transform infrared

We used real‐time Fourier transform infrared to monitor the conversion of both thiol and ene (vinyl) functional groups independently during photoinduced thiol–ene photopolymerizations. From these results, the stoichiometry of various thiol–ene and thiol–acrylate polymerizations was determined. For thiol–ene polymerizations, the conversion of ene functional groups was up to 15% greater than the conversion of thiol functional groups. For stoichiometric thiol–acrylate polymerizations, the conversion of the acrylate functional groups was roughly twice that of the thiol functional groups. With kinetic expressions for thiol–acrylate polymerizations, the acrylate propagation kinetic constant was found to be 1.5 times greater than the rate constant for hydrogen abstraction from the thiol. Conversions of thiol–acrylate systems of various initial stoichiometries were successfully predicted with this ratio of propagation and chain‐transfer kinetic constants. Thiol–acrylate systems with different initial stoichiometries exhibited diverse network properties. Thiol–ene systems were initiated with benzophenone and 2,2‐dimethoxy‐2‐phenylacetophenone as initiators and were also polymerized without a photoinitiator. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3311–3319, 2001     

High‐throughput kinetic analysis of acrylate and thiol‐ene photopolymerization using temperature and exposure time gradients

In this work, a high‐throughput technique for evaluating photopolymers is developed to enable simultaneous measurement of the effects of temperature in combination with exposure time. Temperature and exposure time gradients were produced in orthogonal directions on a single sample, and subsequently sampled using Fourier transform infrared (FTIR) spectroscopy. The technique developed here allows for photopolymerization kinetics to be analyzed rapidly over a large range of industrially relevant temperatures, giving insight into the role temperature and the polymer's glass transition temperature have in dictating the photopolymerization kinetics. In the 70/30 wt % hexyl acrylate and hexanediol diacrylate system, conversion in samples below the glass transition temperature (T_G) was 66 ± 2% after 12 s, significantly lower than the 93 ± 4% conversion at 12 s for samples polymerized at temperatures above the T_G. In addition, a thiol‐ene system was analyzed to study the effect of temperature on the ene homopolymerization in allyl ether monomers, which leads to incomplete thiol conversion in stoichiometrically balanced systems. At a 60% thiol conversion, the allyl ether‐ene conversion at all temperatures is 65 ± 3% irrespective of initial formulation temperature, indicative of the homopolymerization behavior being nearly independent of temperature. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1502–1509, 2008     

N‐Bromosuccinimide as a thermal iniferter for radical polymerization

N‐Bromosuccinimide (NBS) was used as a thermal iniferter for the initiation of the bulk polymerizations of methyl methacrylate, methyl acrylate, and styrene. The polymerizations showed the characteristics of a living polymerization: both the yields and the molecular weights of the resultant polymers increased linearly as the reaction time increased. The molecular weight distributions of the polymers were 1.42–1.95 under the studied conditions. The resultant polymers could be used as macroiniferters to reinitiate the polymerization of the second monomer. The copolymers poly(methyl methacrylate)‐b‐polystyrene and polystyrene‐b‐poly(methyl methacrylate) were obtained and characterized. End‐group analysis of the resultant poly(methyl methacrylate), poly(methyl acrylate), and polystyrene confirmed that NBS behaved as a thermal iniferter. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2567–2573, 2005     

Influence of the alkene structure on the mechanism and kinetics of thiol–alkene photopolymerizations with real‐time infrared spectroscopy

The effect of the chemical structure on the reactivity of alkenes used in thiol–ene photopolymerizations has been investigated with real‐time infrared spectroscopy. Model studies of thiol–ene photoreactions with various monofunctional hydrocarbon alkenes and the monofunctional thiol ethyl‐3‐mercaptopropionate have been performed to identify and understand structure–reactivity relationships. The results demonstrate that terminal enes react very rapidly with thiol, achieve complete conversion, and are independent of the aliphatic hydrocarbon substituent length. Disubstitution on a single carbon of a terminal ene significantly reduces the reactivity, whereas substitution on the carbon α to the terminal ene has a minimal influence on the reactivity. Internal trans enes display reduced reactivity and a lower overall conversion and deviate from the standard thiol–ene reaction mechanism because of steric strain induced by 1,3‐interactions. The reactivity and conversion of internal trans enes decrease as the substituents on the ene become larger, reaching a minimum when the substituent size is greater than or equal to that of propyl groups. Internal cis enes react rapidly with thiol; however, they undergo a fast isomerization–elimination reaction sequence generating the trans ene, which proceeds to react at a reduced rate with thiol. The reactivity of cyclic enes is dictated by ring strain, stereoelectronic effects, and hydrogen abstractability. The reactivity trends in the model studies have been used to explain the photopolymerization mechanism and kinetics of a series of multifunctional thiol–ene systems. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6283–6298, 2004     

Synthesis of a new type of core–shell particle from hyperbranched polyglycerol

Based on hyperbranched polyglycerol (PG), a route to prepare particles with a novel topology was developed. The hydroxyls of PG were converted to trithiocarbonates, and the latter were used to mediate the surface graft polymerization of N,N‐dimethylaminoethyl acrylate. The poly(N,N‐dimethylaminoethyl acrylate) shell was crosslinked by 1,6‐dibromohexane and then parted from the core by the cleavage of trithiocarbonates with sodium borohydride. Novel particles with thiol groups located on the interface between the PG core and poly(N,N‐dimethylaminoethyl acrylate) shell were thus formed. The shell crosslinking could be performed at very high solid contents (2–4%). These polymer particles showed pH‐ and temperature‐dependent solubility. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5458–5464, 2005     

New photo‐induced thiol‐ene crosslinked films based on linear methacrylate copolymer polythiols

Thiol‐ene radical addition by photolysis is a highly efficient click reaction of sufhydryl groups with reactive enes that has been extensively explored as a promising means to construct multifunctional materials. Here, photo‐induced thiol‐ene crosslinked films composed of linear methacrylate copolymer polythiols (MCPsh) are reported. Well‐defined MCPsh copolymers were prepared by thiol‐responsive cleavage of pendant disulfide linkages positioned in the corresponding methacrylate copolymers with narrow molecular weight distribution which were synthesized by a controlled radical polymerization method. With a commercially available multifunctional acrylate as a model ene, photo‐induced thiol‐ene radical polyaddition of these polythiols is competitive to free‐radical homopolymerization of acrylates, yielding crosslinked films exhibiting rapid cure, uniform network, and enhanced mechanical properties; these properties are required for high performance coating materials. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2860–2868.     

An efficient nonisocyanate route to polyurethanes via thiol‐ene self‐addition

A novel and efficient strategy for the synthesis of nonisocyanate polyurethanes has been developed via thiol–ene self‐photopolymerization. An aliphatic thiol–ene carbamate monomer (allyl(2‐mercaptoethyl)carbamate, AMC) was synthesized by a one‐step synthesis procedure, from cysteamine and allyl chloroformate. The urethane group was therefore incorporated directly into the monomer precursor, avoiding the problems associated to toxic isocyanates. AMC was successfully stabilized with the radical inhibitor pyrogallol (1% wt). In addition, the use of phenyl phosphonic acid as coadditive allowed its stabilization for lower concentrations of pyrogallol (0.1% wt). AMC was directly transformed into thermoplastic polyurethane (TPU) through thiol–ene photopolymerization by UV‐irradiation at 365 nm. The obtained TPU presented semi‐crystalline nature and very high thermal stability (T_5% ～325 °C). It was found that high concentrations of pyrogallol decreased the reaction rate and final conversion of photopolymerization. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3017–3025     

Photopolymerization of thiol‐ene systems based on oligomeric thiols

Thiol oligomers were copolymerized with a triallyl ether by a photoinduced polymerization process. These oligomeric thiol‐ene systems comprise the same components as a photopolymerized thiol‐ene‐acrylate ternary system, yet the photopolymerized networks have much lower glass transition temperatures. An investigation into the effect of oligomeric thiol design on network formation was conducted by analyzing the reaction kinetics and thermal/mechanical properties of the thiol‐ene networks. Real‐time FTIR analysis shows that total conversion is >90% for all thiols investigated. Photo‐DSC analysis shows that the maximum exotherm rate is roughly equivalent for all of the thiols when the equivalent weight of the thiol is taken into account. As would be expected, the glass transition temperature and tensile strength increase with thiol functionality and lower thiol equivalent weight for thiols with functionality from 2 to 4. Films made using the oligomeric thiols have essentially the same glass transition temperatures and tensile modulus values regardless of thiol design. These results distinguish the method for generation of networks consisting of an initial Michael reaction of thiols and acrylates followed by a photoinitiated copolymerization with a multifunctional ene from the traditional photolysis of the corresponding thiol‐ene‐acrylate ternary systems with no Michael reaction. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 14–24, 2009     

Depth characterization by confocal raman microscopy of oxygen inhibition in free radical photopolymerization of acrylates: Contribution of the thiol chemistry

The oxygen inhibition of acrylate photopolymerization using visible light was depth characterized by confocal Raman microscopy. The sample thickness was found to influence the depth conversion profile. With increasing sample thickness, the conversion at the surface was increased and the oxygen‐affected layer (OAL) decreased, up to a limit where the profiles became independent of the thickness. The addition of a thiol in the acrylate mixture reduced the OAL and the conversion in this region increased. This effect was noticeable even at low concentration of thiol. Real‐time infrared spectroscopy (RT‐FTIR) experiments pointed out that for low thiol content, this beneficial effect is not only attributable to the thiol–ene process—oxygen insensitive—but also to the homopolymerization of acrylates which is enhanced. Homopolymerization and thiyl radical addition were found to have the same impact on the overall mechanism. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Hairy polymeric nanocapsules with ph‐responsive shell and thermoresponsive brushes: Tunable permeability for controlled release of water‐soluble drugs

The hairy poly(methacrylic acid‐co‐divinylbenzene)‐g‐poly(N‐isopropylacrylamide) (P(MAA‐co‐DVB)‐g‐PNIPAm) nanocapsules with pH‐responsive P(MAA‐co‐DVB) inner shell and temperature‐responsive PNIPAm brushes were prepared by combined distillation–precipitation copolymerization and surface thiol‐ene click grafting reaction using 3‐(trimethoxysilyl)propyl methacrylate‐modified silica (SiO₂‐MPS) nanospheres as a sacrificial core material. The well‐defined PNIPAm was synthesized by a reversible addition fragmentation chain transfer (RAFT) polymerization. The chain end was converted to a thiol by chemical reduction. The PNIPAm was integrated into the nanocapsules via thiol‐ene click reaction. The surface thiol‐ene click reaction conduced to tunable grafting density of PNIPAm brushes. The grafting densities decreased from 0.70 chains nm^?2 to 0.15 chains nm^?2 with increasing the molecular weight of grafted PNIPAm chains. Using water soluble doxorubicin hydrochloride (DOX·HCl) as a model molecular, the tunable shell permeability of the nanocapsule was investigated in detail. The permeability constant can be tuned by controlling the thickness of the P(MAA‐co‐DVB) inner shell, the grafting density of PNIPAm brushes, and the environmental pH and temperature. The tunable shell permeability of these nanocapsules results in the release of the loaded guest molecules with manipulable releasing kinetics. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2202–2216     

Efficient initiation of radical‐mediated thiol‐ene chemistry with photoactive silica particles

This work aims at the design of photoactive inorganic filler by covalently attaching tri(methoxy)silyl‐functionalized bis(acyl)phosphane oxides (TEMSI²‐BAPO) onto silica particles. The immobilization of the photoactive groups is evidenced by spectroscopic measurements and thermal gravimetric analysis. The modified particles are then incorporated into thiol–ene resins to study the efficiency of the Norrish type I photofragmentation reaction of the covalently bound TEMSI²‐BAPO derivatives. The photopolymerization kinetics of the thiol–ene system is monitored by FT‐IR spectroscopy and photo‐DSC upon prolonged exposure with UV‐light and compared with the results achieved with IRGACURE 819 (free BAPO). Rapid curing and high conversion yields are obtained evidencing the high efficiency of the photoactive particles. In addition, negative‐toned patterns are inscribed in thin thiol–ene films by photolithographic processes and characterized by microscopic techniques demonstrating the versatile applicability of the photoactive particles. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 894–902     

Quadruple click reactions for the synthesis of cysteine‐terminated linear multiblock copolymers

Synthesis of cysteine‐terminated linear polystyrene (PS)‐b‐poly(ε‐caprolactone) (PCL)‐b‐poly(methyl methacrylate) (PMMA)/or poly(tert‐butyl acrylate)(PtBA)‐b‐poly(ethylene glycol) (PEG) copolymers was carried out using sequential quadruple click reactions including thiol‐ene, copper‐catalyzed azide–alkyne cycloaddition (CuAAC), Diels–Alder, and nitroxide radical coupling (NRC) reactions. N‐acetyl‐L ‐cysteine methyl ester was first clicked with α‐allyl‐ω‐azide‐terminated PS via thiol‐ene reaction to create α‐cysteine‐ω‐azide‐terminated PS. Subsequent CuAAC reaction with PCL, followed by the introduction of the PMMA/or PtBA and PEG blocks via Diels–Alder and NRC, respectively, yielded final cysteine‐terminated multiblock copolymers. By ¹H NMR spectroscopy, the DP_ns of the blocks in the final multiblock copolymers were found to be close to those of the related polymer precursors, indicating that highly efficient click reactions occurred for polymer–polymer coupling. Successful quadruple click reactions were also confirmed by gel permeation chromatography. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Photocuring kinetics of UV‐initiated free‐radical photopolymerizations with and without silica nanoparticles

We used photodifferential scanning calorimetry to investigate the photocuring kinetics of UV‐initiated free‐radical photopolymerizations of acrylate systems with and without silica nanoparticles. Two kinetics parameters—the rate constant (k) and the order of the initiation reaction (m)—were determined for hybrid organic–inorganic nanocomposite systems containing different amounts of added silica nanoparticles (0–20 wt %) and at different isothermal temperatures (30–100 °C) using an autocatalytic kinetics model. The kinetic analysis revealed that the silica nanoparticles apparently accelerate the cure reaction and cure rate of the UV‐curable acrylate system, most probably due to the synergistic effect of silica nanoparticles during the photopolymerization process. However, a slight decrease in polymerization reactivity that occurred when the silica content increased beyond 15 wt % was attributed to aggregation between silica nanoparticles. We also observed that the addition of silica nanoparticles lowered the activation energy for the UV‐curable acrylate system, and that the collision factor for the system with silica nanoparticles was higher than that obtained for the system without silica nanoparticles, indicating that the reactivity of the former was greater than that of the latter. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 658–670, 2005     

Effect of introducing a cationic system into a thiol‐ene photopolymerizable formulation

Hybrid materials derived from a thiol‐ene and cationic polymerization were obtained from concomitant polymerization. The hybrid materials were cured by both photopolymerization and thermally induced polymerization. The kinetics of the photopolymerization were measured using time resolved‐IR and optical pyrometry. The nucleophilic character of the polysulfide obtained initially in the thiol‐ene polymerization inhibited the development of the cationic photoinitiated polymerization of epoxy monomers. Besides, the epoxide groups underwent a proton catalyzed addition reaction with the thiols to form new sulfides groups in the reaction mixture. It is proposed that the formed sulfides can terminate the growing polyether chains forming dormant species like trialkylsulfonium salts. These salts promote the thermal polymerization of the epoxy monomer in a post treatment, producing hard and transparent materials. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4829–4843, 2007     

Blue LED light‐sensitive benzo pyrazolo (or imidazo) isoquinolinone derivatives in high‐performance photoinitiating systems for polymerization reactions

Isoquinolinone derivatives (IQ) have been synthesized and combined with different additives (an amine, 2,4,6‐tris(trichloromethyl)‐1,3,5‐triazine, an iodonium salt, or N‐vinylcarbazole) to produce reactive species (i.e. radicals and cations) being able to initiate the radical polymerization of acrylates, the cationic polymerization of epoxides, the thiol‐ene polymerization of trifunctional thiol/divinylether, and the synthesis of epoxide/acrylate interpenetrated polymer network IPN upon exposure to very soft polychromatic visible lights, blue laser diode or blue LED lights. Compared with the use of camphorquinone based systems, the novel combinations employed here ensures higher monomer conversions (～50–60% vs. ～15–35%) and better polymerization rates in radical polymerization. The chemical mechanisms are studied by steady‐state photolysis, fluorescence, cyclic voltammetry, laser flash photolysis, and electron spin resonance spin trapping techniques. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 567–575     

Photo‐initiated thiol–ene “click” hydrogels from RAFT‐synthesized poly(N‐isopropylacrylamide)

Despite the efficiency and robustness of the widely used copper‐catalyzed 1,3‐dipolar cycloaddition reaction, the use of copper as a catalyst is often not attractive, particularly for materials intended for biological systems. The use of photo‐initiated thiol‐ene as an alternative “click” reaction to synthesize “model networks” is investigated here. Poly(N‐isopropylacrylamide) precursors were synthesized by reversible addition fragmentation chain transfer (RAFT) polymerization and were designed to have trithiocarbonate moieties as end groups. This structure design provides opportunity for subsequent end‐group modifications in preparation for thiol‐ene “click.” Two reaction routes have been proposed and studied to yield thiol and ene moieties. The advantages and disadvantages of each reaction path were investigated to propose a simple but efficient route to prepare copper‐free “click” hydrogels. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4626–4636