Total‐reflection X‐ray diffraction study of friction‐transferred poly(tetrafluoroethylene) film

The orientational structure of the friction‐transferred poly(tetrafluoroethylene) (PTFE) film, which consists of highly oriented polymer strands, was evaluated with energy‐dispersive total‐reflection X‐ray diffractometry. In the film, each PTFE molecule is oriented along the friction direction, and PTFE crystallites have a preferred orientation with respect to the substrate surface. The orientational distribution of the chain direction was quantitatively evaluated. The half‐width of the distribution was determined to be about 3°. The dependence of the orientational distribution on temperature is discussed. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 432–438, 2001     

Small‐angle X‐ray scattering study of a weak polyelectrolyte in water

Small‐angle X‐ray scattering (SAXS) was used to obtain solution parameters of a weak polyelectrolyte in water in the absence of any additives, such as neutralizing agents or salt. Poly(acrylic acid) (PAA) was used as a weak polyelectrolyte from which SAXS data were obtained in the dilute region of 1–10 mg cm^?3. An intrinsic viscosity of 15.7 dL g^?1 was obtained from a plot of reciprocal reduced viscosities versus the concentration. The application of the SAXS data, that is, the contour length (L = 1.97 × 10⁴ Å), the persistence length (a* = 58.5 Å), and the molecular weight (M = 5.9 × 10⁵ Da), to the Yamakawa–Fujii equation suggested that PAA in water at 25 °C could be described as a wormlike chain having a cylindrical body of d = 6 Å. An end‐to‐end distance (r = 1.6 × 10³ Å) was calculated from r = 2a*L ? 2(a*)². The nonisotropic expansion factor (α = 2.9) was calculated for PAA expanding from the random coil in dioxane at 30 °C (Θ temperature) to the wormlike chain in water at 25 °C. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1263–1272, 2003     

Melt spinning and laser‐heated drawing of a new semiaromatic polyamide,PA9‐T fiber

Fibers of PA9‐T, a new semiaromatic polyamide containing a long aliphatic chain, were prepared by melt spinning. As‐spun fibers were subsequently drawn with a CO₂ laser‐heated drawing system at different draw ratios and various drawing velocities. On‐line observations of drawing points deciphered two drawing states; namely, flow drawing and neck drawing, over the entire range of drawing. Drawing stress revealed that flow drawing is induced by slight drawing stress under a low draw ratio up to 3, and neck drawing is induced by relatively high drawing stress under a higher draw ratio. The effect of drawing stress and drawing velocity on the development of the structure and properties has been characterized through analysis of birefringence, density, WAXD patterns, and tensile, thermal, and dynamic viscoelastic properties. For the neck‐drawn fibers, almost proportional enhancements of crystallinity and molecular orientation with drawing stress were observed. The flow‐drawn fibers have an essentially amorphous structure, and birefringence and density do not always have a linear relation with properties. The fibers drawn at high drawing speed exhibit improved fiber structure and superior mechanical properties. The maximum tensile strength and Young's modulus of PA9‐T drawn fibers were found to be 652 MPa and 5.3 GPa, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 433–444, 2004     

Thermal and X‐ray powder diffraction studies of aliphatic polyester dendrimers

The syntheses and thermal and X‐ray powder diffraction analyses of three sets of aliphatic polyester dendrimers based on 2,2‐bis(hydroxymethyl)propionic acid as a repeating unit and 2,2‐dimethyl‐1,3‐propanediol, 1,5‐pentanediol, and 1,1,1‐tris(hydroxymethyl)ethane as core molecules are reported. These dendritic polyesters were prepared in high yields with the divergent method. The thermal properties of these biodendrimers were evaluated with thermogravimetric analysis and differential scanning calorimetry. The thermal decomposition of the compounds occurred around 250 °C for the hydroxyl‐ended dendrimers and around 150 °C for the acetonide‐protected dendrimers. In addition, the crystallinity of the lower generation dendrimers was evaluated with X‐ray powder diffraction. The highest crystallinity and the highest melting points were observed for the first‐generation dendritic compounds. The higher generation dendrimers showed weaker melting transitions during the first heating scan. Only the glass‐transition temperatures were observed in subsequent heating scans. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5574–5586, 2004     

Wide‐angle X‐ray diffraction and differential scanning calorimetry study of the crystallization of poly(ethylene naphthalate), poly(butylene naphthalate), and their copolymers

The crystallization behavior of a series of poly(ethylene‐co‐butylene naphthalate) (PEBN) random copolymers was studied. Wide‐angle X‐ray diffraction (WAXD) patterns showed that the crystallization of these copolymers could occur over the entire range of compositions. This resulted in the formation of poly(ethylene naphthalate) or poly(butylene naphthalate) crystals, depending on the composition of the copolymers. Sharp diffraction peaks were observed, except for 50/50 PEBN. Eutectic behavior was also observed. This showed isodimorphic cocrystallization of the PEBN copolymers. The variation of the enthalpy of fusion of the copolymers with the composition was estimated. The isothermal and nonisothermal crystallization kinetics were studied. The crystallization rates were found to decrease as the comonomer unit content increased. The tensile properties were also measured and were found to decrease as the butylene naphthalate content of the copolymers increased. For initially amorphous specimens, orientation was proved by WAXD patterns after drawing, but no crystalline reflections were observed. However, the fast crystallization of drawn specimens occurred when they were heated above the glass‐transition temperature. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 843–860, 2004     

Barrier property enhancement of polyamide 6 by blending with a polyhydroxyamino‐ether resin

In this work, the transport properties of the system formed by polyamide 6 (PA6) and polyhydroxyamino‐ether resin (PHAE) have been studied after characterizing the miscibility behavior. A single glass transition has been observed using differential scanning calorimetry that usually means total miscibility, but measurements by solid‐state cross‐polarization magic angle spinning NMR have shown that this system is only partially miscible, in good agreement with phase behavior reported before. Both carbon dioxide and water vapor transport properties of PA6/PHAE blends have been measured. For both penetrants, permeability coefficient shows an interesting negative deviation from the additive value, even the barrier character to carbon dioxide of pure PHAE is maintained up to 60 % in PA6 composition. Besides, PHAE reduces the plasticization effect of water in PA6. These improvements are very interesting for the PA 6 due to its wide use in packaging applications. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1625–1634, 2009     

Online wide‐angle X‐ray diffraction/small‐angle X‐ray scattering measurements for the CO2‐laser‐heated drawing of poly(ethylene terephthalate) fiber

Fiber‐structure‐development in the poly(ethylene terephthalate) fiber drawing process was investigated with online measurements of wide‐angle and small‐angle X‐ray scattering with both a high‐luminance X‐ray source and a CO₂‐laser‐heated drawing system. The intensity profile of the transmitted X‐ray confirmed the location of the neck‐drawing point. The diffraction images had a time resolution of several milliseconds, and this still left much room for improvement. Crystal diffraction appeared in the wide‐angle X‐ray images almost instantaneously about 20 ms after necking, whereas a four‐point small‐angle X‐ray scattering pattern appeared immediately after necking. With the elapse of time after necking, the four‐point scattering pattern changed into a meridional two‐point shape. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1090–1099, 2005     

In situ fibrillation of polyamide 6 in isotactic polypropylene occurring in the laminating‐multiplying die

The polyamide 6 (PA6)/isotactic polypropylene (iPP) in situ fibrillation composites are prepared by a novel extrusion die with an assembly of laminating‐multiplying elements (LMEs). The scanning electron micrographs illustrate that the dividing‐multiplying processes in LMEs elongate, break, and stabilize the dispersed PA6 phase in the iPP matrix along the flowing direction (FD). The morphology development of PA6 with different LME numbers greatly affects the rheological properties, crystalline behaviors, and mechanical properties. The dynamic rheological test performed at 195°C shows that the increased spatial restriction of the high‐aspect‐ratio PA6 particles increases the viscoelastic moduli, complex viscosity, and relaxation time. The crystalline analysis reveals that the heterogeneous nucleation becomes predominant and the transcrystalline morphology is observed in those samples produced by more LMEs. The tensile tests indicate that both, breaking strength and elongation, enhanced simultaneously because of the fibrillation of dispersed phase and the improvement in interfacial adhesion between the fibers and the matrix. Copyright © 2009 John Wiley & Sons, Ltd.     

Time‐resolved crystallization study of absorbable polymers by synchrotron small‐angle X‐ray scattering

Changes in the lamellar morphology that occurred during the quiescent isothermal crystallization of absorbable poly(p‐dioxanone) (PDS) and PDS/poly(glycolide) block copolymer were studied by synchrotron small‐angle X‐ray scattering. Important morphological parameters such as the lamellar long period, the thicknesses of the crystal and amorphous phases, and the scattering invariant were estimated as a function of time, and trends observed over a wide range of experimental conditions are discussed. Thicker but more perfect lamellae were detected at higher crystallization temperatures. The breadth of the normalized semilog Lorentz‐corrected intensity peak systematically decreased with increasing temperature. In addition, the values of the crystallization half‐time and the Avrami exponent (n = 2.5), determined from the real‐time changes in the lamellar development, showed superb agreement with the bulk crystallinity data generated from other experimental techniques, such as calorimetry and dielectric relaxation spectroscopy. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 153–167, 2001     

Simultaneous wide‐angle X‐ray diffraction and differential scanning calorimetry analysis of the melting and recrystallization behavior of polyethylene and isotactic polypropylene containing cyclopentane units in the main chain

The melting and crystallization behavior of polyethylene and isotactic polypropylene containing 1,2‐ or 1,3‐disubstituted cyclopentane units in the main chain has been studied with simultaneous wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry. For the ethylene‐based copolymers, the position of a reflection peak in the WAXD patterns shifts to a low angle with the increasing acquired temperature. The temperature dependence on the axial length of the crystal lattice is more marked in the copolymers forming orthorhombic crystals (containing 1,2‐cyclopentane or 5.6 mol % 1,3‐cyclopentane units) than in those forming hexagonal crystals (containing 8.1 mol % 1,3‐cyclopentane units). For the isotactic propylene‐based copolymers, the position of the reflection peaks in the WAXD patterns is independent of the acquired temperature. The proportion of the γ form in the copolymer containing the 1,2‐cyclopentane units is higher than that in the copolymers containing the 1,3‐cyclopentane units. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1457–1465, 2004     

Tuning the localization of finely dispersed cellulose nanocrystal in poly (lactic acid)/bio‐polyamide11 blends

A versatile approach to control the localization of cellulose nanocrystal (CNC) in PLA/PA11 blends is presented. A PEO/CNC mixture with a high level of CNC dispersion is prepared through a combination of high pressure homogenization and freeze‐drying. The prepared PEO/CNC mixture is then incorporated into the PLA/PA11 blends using two different strategies. Typically for CNC/PLA/PA11, the CNCs selectively localize in PA11. However, PEO‐coated CNC particles segregate into PLA irrespective of whether the PEO/CNC mixture is premixed with PLA or PA11. It is suggested that a strong interaction between PEO and CNC particles combined with the PLA/PEO miscibility facilitates the localization of PEO‐coated CNC in the PLA. The localization of PEO‐coated CNC in the PLA has no effect on the morphology of the PLA‐5PEO/PA11 with matrix/dispersed phase form. However, 2 wt % PEO‐coated CNC in the co‐continuous (PLA‐5PEO)/PA11 50/50 vol % blend diminishes the phase thickness from 11 ± 1 to 4 ± 1.5 μm. This is attributed to a retarded relaxation of the PLA phase. This work outlines a strategy to control the CNC localization into a given polymeric phase in a binary polymer–polymer mixture. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 576–587     

Long‐range orientation correlations and molecular alignment in sheared thermotropic copolyester. In situ light and X‐ray scattering

Orientation correlations induced by shear flow and their relaxation were investigated using in situ small‐angle light scattering (SALS) in the thermotropic random copolyester of 60 mol% hydroxybenzoic acid (B) and 40 mol% ethylene terephthalate (ET). B‐ET displays a nematic polydomain texture, the SALS and wide‐angle X‐ray scattering (WAXS) patterns are amorphous and isotropic. Shear flow produced optical defect multiplication with the consequent reduction of the micro–domains size. However, SALS detected long‐range spatial correlations within the optically chaotic texture, the SALS patterns showed bimodal orientation of defects. After cessation of shear the orientation correlation rapidly relaxed back to a polydomain and the SALS pattern became again isotropic. Above a threshold shear rate of about the SALS pattern showed unimodal orientation arising from line defects oriented nearly orthogonal to the velocity axis. Strikingly, the texture relaxation now showed the well known “banded texture”. The threshold shear rate coincided with a significant increase in the degree of molecular alignment as determined from in situ X‐ray scattering. This technique also showed that shear flow always oriented the molecular chains along the flow direction regardless of the shear rate. Copyright © 2007 John Wiley & Sons, Ltd.     

Preparation of high‐temperature polyurethane by alloying with reactive polyamide

A series of novel poly(urethane amide) films were prepared by the reaction of a polyurethane (PU) prepolymer and a soluble polyamide (PA) containing aliphatic hydroxyl groups in the backbone. The PU prepolymer was prepared by the reaction of polyester polyol and 2,4‐tolylenediisocyanate and then was end‐capped with phenol. Soluble PA was prepared by the reaction of 1‐(m‐aminophenyl)‐2‐(p‐aminophenyl)ethanol and terephthaloyl chloride. The PU prepolymer and PA were blended, and the clear, transparent solutions were cast on glass substrates; this was followed by thermal treatments at various temperatures to produce reactions between the isocyanate group of the PU prepolymer and the hydroxyl group of PA. The opaque poly(urethane amide) films showed various properties, from those of plastics to those of elastomers, depending on the ratio of the PU and PA components. Dynamic mechanical analysis showed two glass‐transition temperatures (T_g's), a lower T_g due to the PU component and a higher T_g due to the PA component, suggesting that the two polymer components were phase‐separated. The rubbery plateau region of the storage modulus for the elastic films was maintained up to about 250 °C, which is considerably higher than for conventional PUs. Tensile measurements of the elastic films of 90/10 PU/PA showed that the elongation was as high as 347%. This indicated that the alloying of PU with PA containing aliphatic hydroxyl groups in the backbone improved the high‐temperature properties of PU and, therefore, enhanced the use temperature of PU. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3497–3503, 2002     

Effect of the initial matrix material on the structure of radiation‐grafted ion‐exchange membranes: Wide‐angle and small‐angle X‐ray scattering studies

Seven different fluoropolymer films were used as matrix materials for radiation‐grafted ion‐exchange membranes. The crystallinity and preferred orientation of these membranes were studied with wide‐angle X‐ray scattering, and the lamellar structure of the membranes was examined with small‐angle X‐ray scattering. The crystallinity of poly(vinylidene fluoride) (PVDF)‐based matrix materials varied between 57 and 40%, and the crystallinity of the sulfonated samples varied between 34 and 23%. The lamellar periods of PVDF‐based matrix materials were about 115 Å, and the lamellar periods of poly(ethylene‐alt‐tetrafluoroethylene) and poly(tetrafluoroethylene‐co‐hexafluoropropylene) were 250 and 212 Å, respectively. When the samples were grafted, the lamellar periods increased. Correlation function analysis showed very clearly that the long‐range order decreased because of grafting and sulfonation processes. For those samples that showed good proton conductivity, the lamellar period also increased because of sulfonation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1539–1555, 2002     

Mutual influence of the morphology and capillary rheological properties in nylon/glass‐fiber/liquid‐crystalline‐polymer blends

Nylon‐6/glass‐fiber (GF)/liquid‐crystalline‐polymer (LCP) ternary blends with different viscosity ratios were prepared with three kinds of nylon‐6 with different viscosities as matrices. The rheological behaviors of these blends were characterized with capillary rheometry. The morphology was observed with scanning electron microscopy and polarizing optical microscopy. This study showed that although LCP did not fibrillate in binary nylon‐6/LCP blends, LCP fibrillated to a large aspect ratio in some ternary blends after GF was added. The addition of 5 wt % LCP significantly reduced the melt viscosity of nylon‐6/GF blends to such an extent that some nylon‐6/GF/LCP blends had quite low viscosities, not only lower than those of neat resins and nylon‐6/GF blends but also lower than those of corresponding nylon‐6/LCP blends. The mutual influence of the morphology and rheological properties was examined. The great reduction of the melt viscosity was considered the result of LCP fibrillation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1619–1627, 2004     

Crystallinity changes in plastically deformed isotactic polypropylene evaluated by x‐ray diffraction and differential scanning calorimetry methods

The crystallinity of isotactic polypropylene (iPP), when deformed with plastic plane‐strain compression, was studied with wide‐angle X‐ray scattering (WAXS) and differential scanning calorimetry (DSC) techniques. A comparison of the obtained crystallinity data with annealed iPP samples was performed. The material used in this study was commercial iPP (weight‐average molecular weight = 117.400 g/mol; number‐average molecular weight = 17.300 g/mol). A significant decrease in the crystallinity was observed with increasing deformation pressure when the X‐ray method was employed, whereas only a small decrease was registered when the DSC method of crystallinity determination was used. However, the annealed iPP samples demonstrated a slight crystallinity increase when evaluated by both techniques. The reason for the difference between WAXS and DSC crystallinity results is discussed. This study of iPP specimens subjected to large deformation led us to the conclusion that the WAXS method provides accurate crystallinity values for the deformed material, whereas the values obtained by the DSC method do not reproduce the real crystallinity of the deformed material. This is due to the inherent heating process of the method, which causes a relaxation process and a significant change in the crystallinity of the deformed material, providing values nearer to its intrinsic equilibrium state. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 896–903, 2002     

Structure determination of a new cocrystal of carbamazepine and dl‐tartaric acid by synchrotron powder X‐ray diffraction

The crystal structure of a new cocrystal of carbamazepine (systematic name: 5H‐dibenzo[b,f]azepine‐5‐carboxamide, C₁₅H₁₂N₂O) and dl ‐tartaric acid (C₄H₆O₆), obtained by liquid‐assisted grinding, was solved by powder X‐ray diffraction (PXRD). The high‐resolution PXRD pattern of this new phase was recorded at room temperature thanks to synchrotron experiments at the European Synchrotron Radiation Facility (Grenoble, France). The starting structural model was generated by a Monte‐Carlo simulated annealing method. The final structure was obtained through Rietveld refinement and an energy minimization simulation was used to estimate the H‐atom positions. The stability of the proposed structure as a function of temperature was also assessed from molecular dynamics simulations. The symmetry is monoclinic (space group P2₁/c) and contains eight molecules per unit cell, namely, four dl ‐tartaric acid and four carbamazepine molecules.     

Morphological changes during heating in poly(L‐lactic acid)/poly(butylene succinate) blend systems as studied by synchrotron X‐ray scattering

Blends of poly(L ‐lactic acid) (PLA) and poly(butylene succinate) (PBS) were prepared in various compositions via melt mixing, and the morphological changes were investigated with differential scanning calorimetry and synchrotron wide‐angle and small‐angle X‐ray scattering techniques at a heating rate of 10 °C/min. Differential scanning calorimetry thermograms of PLA/PBS blends showed two distinct melting peaks over the entire composition range. The exothermal peak for PLA shifted significantly to a lower temperature and overlapped with that of PBS around 100 °C. A depression of the melting point of the PLA component via blending was observed. The synchrotron wide‐angle X‐ray scattering during heating revealed that there was no cocrystallization or crystal modification via blending. The synchrotron small‐angle X‐ray scattering data showed that well‐defined double‐scattering peaks (or peaks with a clear scattering shoulder) appeared during crystallization, indicating that this system possessed dual lamellar stacks. These peaks were deconvoluted into two components with a peak separation computer program, and then the morphological parameters of each component were obtained by means of the correlation function. The long period and average lamellar thickness of the two components before melting decreased with an increasing content of the other polymer component. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1931–1939, 2002     

Surface oxidation process of a diamond‐like carbon film analyzed by difference X‐ray photoelectron spectroscopy

Difference X‐ray photoelectron spectroscopy (D‐XPS) revealed the surface oxidation process of a diamond‐like carbon (DLC) film. Evaluation of surface functional groups on DLC solely by the C 1s spectrum is difficult because the spectrum is broad and has a secondary asymmetric lineshape. D‐XPS clarified the subtle but critical changes at the DLC surface caused by wet oxidation. The hydroxyl (C―OH) group was dominant at the oxidized surface. Further oxidized carbonyl (C?O) and carboxyl (including carboxylate) (COO) groups were also obtained; however, the oxidation of C?O to COO was suppressed to some extent because the reaction required C―C bond cleavage. Wet oxidation cleaved the aliphatic hydrogenated and non‐hydrogenated sp² carbon bonds (C―H sp² and C―C sp²) to create a pair of C―OH and hydrogenated sp³ carbon (C―H sp³) bonds. The reaction yield for C―H sp² was superior at the surface, suggesting that the DLC film was hydrogen rich at the surface. Oxidation of aromatic sp² rings or polycyclic aromatic hydrocarbons such as nanographite to phenols did not occur because of their resonance stabilization with electron delocalization. Non‐hydrogenated sp³ carbon (C―C sp³) bonds were not affected by oxidation, suggesting that these bonds are chemically inert. Copyright © 2014 John Wiley & Sons, Ltd.     

Crystallization and morphology of poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) blends. II. Morphology and crystallization kinetics by time resolved X‐ray scattering

The development of the morphology in poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) (PVDF/PHB) blends upon isothermal and anisothermal crystallization is investigated by time‐resolved small‐ and wide‐angle X‐ray scattering. The components are completely miscible in the melt but crystallize separately; they crystallize stepwise at different temperatures or sequentially with isothermal or anisothermal conditions, respectively. The PVDF crystallizes undisturbed whereas PHB crystallizes in a confined space that is determined by the existing supermolecular structure of the PVDF. The investigations reveal that composition inhomogeneities may initially develop in the remaining melt or in the amorphous phases of the PVDF upon crystallization of that component. The subsequent crystallization of the PHB depends on these heterogeneities and the supermolecular structure of PVDF (dendritically or globularly spherulitic). PHB may form separate spherulites that start to grow from the melt, or it may develop “interlocking spherulites” that start to grow from inside a PVDF spherulite. Occasionally, a large number of PVDF spherulites may be incorporated into PHB interlocking spherulites. The separate PHB spherulites may intrude into the PVDF spherulites upon further growth, which results in “interpenetrating spherulites.” Interlocking and interpenetrating are realized by the growth of separate lamellar stacks (“fibrils”) of the blend components. There is no interlamellar growth. The growth direction of the PHB fibrils follows that of the existing PVDF fibrils. Depending on the distribution of the PHB molecules on the interlamellar and interfibrillar PVDF regions, the lamellar arrangement of the PVDF may contract or expand upon PHB crystallization and the adjacent fibrils of the two components are linked or clearly separated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 974–985, 2004