Effect of organoclay loading and electron beam irradiation on the physico‐mechanical properties of low‐density polyethylene/ethylene‐vinyl acetate blend

The influence of electron beam (EB) irradiation and organoclay (OC) loading on the properties of low‐density polyethylene (LDPE)/ethylene‐vinyl acetate (EVA) blends was investigated. The samples were subjected to the EB irradiation with the dose values of 50 and 250 kGy. X‐ray diffraction (XRD), gel content, mechanical, thermal, and electrical properties were utilized to analyze the characteristics of the LDPE/EVA blends with and without OC at different irradiation dosages. Gel content analysis showed that the OC promotes considerably the insoluble part so that the LDPE/EVA blends filled with OC become fully crosslinked at 250 kGy; possibly through the formation of further crosslinks between OC and polymer chains. The samples irradiated by EB showed enhanced mechanical properties due to the formation of three‐dimensional networks. In addition, thermogravimetric analysis indicated that combined OC loading and radiation‐induced crosslinking improved thermal stability of LDPE/EVA blends considerably. Copyright © 2011 John Wiley & Sons, Ltd.     

Mechanical and thermal properties of irradiated films based on Tilapia (Oreochromis niloticus) proteins

Proteins are considered potential material in natural films as alternative to traditional packaging. When gamma radiation is applied to protein film forming solution it resulted in an improvement in mechanical properties of whey protein films. The objective of this work was the characterization of mechanical and thermal properties of irradiated films based on muscle proteins from Nile Tilapia (Oreochromis niloticus). The films were prepared according to a casting technique with two levels of plasticizer: 25% and 45% glycerol and irradiated in electron accelerator type Radiation Dynamics, 0.550 MeV at dose range from 0 to 200 kGy. Thermal properties and mechanical properties were determined using a differential scanning calorimeter and a texture analyzer, respectively. Radiation from electron beam caused a slightly increase on its tensile strength characteristic at 100 kGy, while elongation value at this dose had no reduction.     

Effect of electron beam irradiation on mechanical and thermal properties of waste polyamide copolymer blended with nitrile‐butadiene rubber

In the present study, the effect of electron beam irradiation on the morphological, thermal, and mechanical properties of waste polyamide copolymer (WPA‐66/6) blended with different contents of acrylonitrile butadiene rubber (NBR) were studied. The prepared blends were subjected to irradiation doses up to 150 kGy and the structural modifications were discussed; non‐irradiated blends were used as control. Mechanical properties, namely, tensile strength (TS), yield strength, elongation at break, and hardness, were followed up as functions of irradiation dose and degree of loading with rubber content. On the other hand, the influence of irradiation dose on the thermal parameters, melting temperature, heat of fusion, ΔH_m of the recycled PA copolymer, and its blend with NBR were also investigated. Copyright © 2009 John Wiley & Sons, Ltd.     

Electron beam crosslinking of poly(ethylene-co-vinyl acetate)/clay nanocomposites

Effect of electron beam irradiation on the thermal and mechanical properties of poly(ethylene-co-vinyl acetate) (EVA)/clay nanocomposites prepared by melt blending method has been investigated. The hot set test results show that elongation at high temperature under static load decreased with the increase of irradiation dose. The tensile modulus increased continuously with increasing dose. While the tensile strength increased up to 100 kGy, it decreased with further increase in dose. The elongation at break decreased continuously with increasing dose. Thermogravimetric analysis showed that thermal stability of the EVA/clay nanocomposites improved with increasing dose. The improvement in the mechanical and thermal properties is attributed to the formation of radiation-induced crosslinking as evidenced by the gel content results.     

Characterization of electron beam irradiation blends based on metallocene ethylene‐1‐octene copolymer

Binary blends using metallocene ethylene‐1‐octene copolymer as matrix were prepared and subjected to electron beam (EB) irradiation (50, 100, and 200 kGy). Gel content and melt flow index values indicated that the blends were crosslinking. Fourier transform infrared‐ATR spectroscopy was used to study the crosslinking and oxidative degradation of the blends via tertiary carbon and carboxyl group formation, respectively. Thermal and mechanical properties were studied showing that the crystallinity of both matrix and dispersed phase decreased with irradiation dose, and that the thermoplastic elastomers with good mechanical properties may be obtained by EB irradiation. Chain branching and scission were also detected at all irradiation doses, although at the highest doses (200 kGy) a crosslinking reaction was the most predominantly observed effect. The successive self‐nucleation annealing technique was used to determine the EB irradiation effects on crystallization of some blends in which crosslinking and chain branching take place, modifying the chain's structure and therefore crystalline regions in the matrix and the dispersed phase. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2432–2440, 2007     

Exploring the effect of radiation crosslinking on the physico‐mechanical,dynamic mechanical and dielectric properties of EOC–PDMS blends for cable insulation applications

This work focuses on the effect of electron beam irradiation on the physico‐mechanical, dynamic mechanical and dielectric properties of blends based on ethylene octene copolymer (EOC) and poly dimethyl siloxane (PDMS) rubber. It is found that electron beam irradiation caused considerable improvement in the physico‐mechanical properties; the tensile strength was enhanced by nearly 35% for 70:30 EOC:PDMS blend. Phase morphology of the blends analyzed before irradiation by scanning electron microscopy (SEM) exhibited droplet/matrix morphology with sizes of the PDMS rubber domain varying from 0.55 µm to 0.47 µm as the amount of PDMS rubber decreased from 30 wt% to 10 wt%. This reduction in the PDMS rubber domain has been correlated with the physico‐mechanical properties of the blends. Further, the dynamic mechanical properties and creep behavior of these EOC:PDMS blends before and after irradiation has been studied. It is inferred that the 70:30 blend after radiation crosslinking shows a 17% decrease in the creep compliance, i.e. higher creep resistance compared to neat blends. All the radiation crosslinked blends exhibited lower dielectric constant, lower dielectric loss and higher electrical resistivity as compared to the virgin blends which makes it suitable for cable insulating application. Copyright © 2016 John Wiley & Sons, Ltd.     

Mechanical properties and heat shrinkability of electron beam crosslinked polyethylene–octene copolymer

The mechanical properties and heat shrinkability of electron beam crosslinked polyethylene–octene copolymer were studied. It was found that gel content increases with increased radiation dose. The analysis of results by the Charlesby–Pinner equation revealed that crosslinking was dominant over chain scission upon irradiation. Formation of a crosslinked structure in the electron beam irradiated sample was confirmed by the presence of a plateau of dynamic storage modulus above the melting point of the polymer. Wide-angle X-ray diffraction revealed that there was little change in crystallinity for the irradiated samples, indicating that radiation crosslinking occurs in the amorphous region of the polymer. The tensile modulus increases, whereas the elongation at break decreases with increased radiation dose. The heat shrinkability of the material increased with an increased radiation dose because the radiation-induced crosslinks serve as memory points during the shrinking process.     

The effect of electron irradiation on the structure and mechanical properties of highly drawn polyethylene fibers

Two very different high-modulus polyethylene fiber samples, a low molecular weight melt-spun and drawn fiber, and a high molecular weight gel-spun and drawn fiber, have been subjected to electron beam irradiation to various doses in vacuum and in the presence of acetylene. The gel content after irradiation in acetylene was found to be much greater than for an equivalent dose in vacuum. The gel content–dose relationship could not be described by either Charlesby–Pinner analysis or the Inokuti equation. This is attributed to the polydispersity and the complications introduced by the unique morphologies of highly drawn fibers. Following previous studies, the tensile creep behavior was interpreted in terms of a model comprising two thermally activated processes in parallel, a low stress process relating to the amorphous network, and a high stress process relating to the continuous crystal fraction. Analysis of the creep behavior of the melt-spun, low molecular weight fiber irradiated in vacuum revealed crosslinking in the amorphous regions and chain scission in the crystal. Chain scission was found to be much reduced when irradiating in acetylene, for which a mechanism has been proposed. The creep rates and activation volumes of the high molecular weight, gel-spun fiber were found to be significantly lower, probably due to the unique morphology. In this case the dominant effect of irradiation on the mechanical properties can be attributed to chain scission rather than crosslinking.     

Thermal and mechanical properties of irradiated poly(vinyl chloride)/calcium carbonate composite

A composite consisting of PVC and CaCO₃ particles was irradiated with different doses of Gamma rays or electron beam in order to compensate the tensile strength decreases by filler addition. The deployment of irradiation process on the composite improved significantly the tensile strength by about 10–20 % using E-beam and Gamma irradiation at a dose of 250 kGy, respectively. Moreover, the irradiated composite exhibited higher thermal stability. Two thermal dehydrochlorination processes after irradiation have been observed instead of three thermal process before. The calculation of the activation energy of each step showed that initiation step consumed about 60 % of the used energy.     

Physical properties of gamma irradiated poly(vinyl alcohol) hydrogel preparations

Poly(vinyl alcohol) films from 15% w/w aqueous solutions and a thickness of 0.2 mm were selected for this study. The films were first humidified and then acetalized and/or gamma irradiated. Then, their physical properties were tested. Tensile strength of the hydrogel films reached its maximum value in samples irradiated with a 80 kGy dose, in the case of acetalized films the dose necessary for maximum tensile strength was only 40 kGy. The combination of acetalization with formaldehyde and gamma radiation produced an elastic hydrogel with good tackiness and excellent mechanical and thermal strength.     

Mechanical properties of high‐density polyethylene and crosslinked high‐density polyethylene in crude oil and its components

The tensile and stress‐relaxation properties of an uncrosslinked and a loosely silane‐crosslinked high‐density polyethylene exposed to organic “crude‐oil” penetrants were assessed. The measurements were performed on penetrant‐saturated samples, surrounded by the organic liquid throughout the experiment. The penetrant solubilities in the two polymers were similar and in accordance with predicted values based on the solubility parameter method. The stiffness and strength of the swollen samples were significantly less than those of the dry samples, indicating a plasticization of the amorphous component. Raman spectroscopy on polyethylene exposed to deuterated n‐hexane revealed a penetrant‐induced partial melting/dissolution of the crystal surface and an intact crystal core component. The stress‐relaxation rates, within the time frame of the experiment (～1 s to 18 h), were approximately the same, independent of silane‐crosslinks and the presence of penetrants. This indicated that the mechanical α‐relaxation, which is the main relaxation process occurring in the measured time interval, was not affected by the penetrants. Consequently, its rate seemed to be independent of the crystal surface dissolution (decrease in the content of crystal‐core interface). The shape of the “log stress–log time” curves of the swollen samples was, however, different from that of the dry samples. This was most likely attributed to a time‐dependent saturation of penetrant to a higher level associated with the stretched state of the polymer sample. The silane crosslinks affected only the elongation at break, which was less than that of the uncrosslinked material. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 641–648, 2006     

A study on chemical composition of spices irradiated by electron beam

Quantitative changes in common organic acids and inorganic acids from spices irradiated by electron beam were studied by Dionex-4000i ion chromograph. The results showed that the acids content of either chilli or the five-spice powder⁽³⁾ irradiated with a dose of 9.94 kGy did not undergo significant changes in comparison with the control samples. The flavour composition in the five-spice powder irradiated by electron beam was also determined by Finnigan MAT-8230B gas chromatograph-mass spectrometer, and compared to the results by heating treatment (120°C, 30min). The comparison indicated that the effect of electron beam treatment on flavour composition was less than that of heating.     

Drawing behavior and characteristics of laser‐drawn polypropylene fibers

Drawing behavior, flow drawing, and neck drawing, was studied for isotacticpolypropylene fibers in CO₂ laser drawing system, and the fiber structure and the mechanical properties of drawn fibers were analyzed. For a certain laser power, flow drawing of polypropylene (PP) was possible up to draw ratio (DR) 19.5. Though the drawing stress was very low, the flow‐drawn PP fiber exhibited oriented crystal structure and improved mechanical properties. On the other hand, neck‐drawing was accomplished from DR 4 to 12, with significant increase in drawing stress that enhanced the development of fiber structure and mechanical properties. Unlike PET, the drawing stress depends not only on the DR, but on irradiated laser power also. The 10–12 times neck‐drawn fibers were highly fibrillated. The fibers having tensile strength 910 MPa, initial modulus 11 GPa, and dynamic modulus 14 GPa were obtained by single‐step laser drawing system. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 398–408, 2006     

Characterization of irradiation-induced crosslink of epoxidised natural rubber/ethylene vinyl acetate (ENR-50/EVA) blend

The effect of irradiation on tensile, dynamic mechanical properties, thermal properties and morphology of ENR-50, EVA and ENR-50/EVA blend was investigated. All the samples were irradiated using a 3.0 MeV electron beam (EB) machine with doses ranging from 20 to 100 kGy. Results indicate that the gel fraction of ENR-50, EVA and ENR-50/EVA blend increases with irradiation dose. Concerning tensile properties, it can be seen that EB radiation increases the tensile strength of all the samples, increases the elongation at break of ENR-50 and ENR-50/EVA blend, reduces the elongation at break of EVA, increases M200 (modulus at 200% strain) of ENR-50 and EVA, while decreases M200 of the ENR-50/EVA blend. For dynamic mechanical studies, it was found that EB radiation increases the T_g of all the samples due to the effect of irradiation-induced crosslinking. The compatibility of ENR-50/EVA blend also found to be improving upon irradiation. In the case of thermal properties, it was detected that T_m, T_c and the degree of crystallinity of ENR-50/EVA blend increase with an increase in irradiation dose. This was due to the perfection in the crystal growth occurring upon radiation. Morphology changes play a major role in the changes of the properties of ENR-50/EVA blend. Finally, it can be concluded that ENR-50/EVA blend can be vulcanized by EB radiation.     

Electron beam irradiations of polypropylene syringe barrels and the resulting physical and chemical property changes

Mechanical, thermal, chemical decomposition and electron spin resonance (ESR) methods were used to study electron beam irradiated polypropylene syringe barrels that were irradiated to a total fractionated dose of 0, 20, 40, 60, and 80 kGy (in steps of 20 kGy). Dose mapping was conducted to determine dose to and through the syringe barrel. Analysis of these data indicated that degradation of the polypropylene syringes increased with an increase in electron beam irradiation.     

Method for Simultaneously Improving the Thermal Stability and Mechanical Properties of Poly(lactic acid): Effect of High-Energy Electrons on the Morphological, Mechanical, and Thermal Properties of PLA/MMT Nanocomposites

Nanocomposites derived from poly(lactic acid) (PLA) and organically modified montmorillonite (oMMT) have been cross-linked by high-energy electrons in the presence of triallyl cyanurate (TAC). The morphology of untreated and cross-linked PLA/MMT nanocomposites was characterized by wide-angle X-ray scattering (WAXS) and transmission electron microscopy (TEM). This treatment can improve both the thermal stability and the glass-transition temperatures of the PLA nanocomposites (e.g., PLA-MMT-TAC 30kGy, 50kGy, and 70kGy) because of the formation of cross-linking structures in the nanocomposites that will considerably reduce the mobility of polymers. Interestingly, at relatively low irradiation doses (e.g., 30 and 50 kGy) a good balance between tensile strength and elongation at break for the PLA nanocomposites could be achieved. These mechanical properties are superior to those of pure PLA. Therefore, combining nanotechnology and electron beam cross-linking is a promising new method of simultaneously improving the mechanical properties (toughness and tensile strength) and thermal stability of PLA.     

Large enhancement of the ionic conductivity in an electron‐beam‐irradiated [poly(ethylene glycol)]xLiClO4 solid polymer electrolyte

The effect of electron‐beam (4–8 MeV) irradiation on the ionic conductivity of a solid polymer electrolyte, poly(ethylene glycol) complexed with LiClO₄, was studied. A large enhancement of the conductivity of nearly two orders of magnitude was observed for the highest dose of irradiation (15 kGy) used. The samples were characterized with differential scanning calorimetry, matrix‐assisted laser desorption/ionization, and electron spin resonance spectroscopy. Although no free radicals were present in the irradiated samples, a decrease in the glass‐transition temperature and an increase in the amorphous fraction were observed. Even though pure poly(ethylene glycol) underwent considerable fragmentation, unexpectedly, no significant fragmentation was observed in the polymer–salt complexes. The enhancement of the conductivity was attributed to an increase in the amorphous fraction of the systems and also to an increase in the flexibility of the polymer chains due to the irradiation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1299–1311, 2004     

Degradation behavior of poly (l-lactide-co-glycolide) films through gamma-ray irradiation

Gamma-ray irradiation is a very useful tool to improve the physicochemical properties of various biodegradable polymers without the use of a heating and crosslinking agent. The purpose of this study was to investigate the degradation behavior of poly (l-lactide-co-glycolide) (PLGA) depending on the applied gamma-ray irradiation doses. PLGA films prepared through a solvent casting method were irradiated with gamma radiation at various irradiation doses. The irradiation was performed using 60Co gamma-ray doses of 25–500 kGy at a dose rate of 10 kGy/h.The degradation of irradiated films was observed through the main chain scission. Exposure to gamma radiation dropped the average molecular weight (M_n and M_w), and weakened the mechanical strength. Thermograms of irradiated film show various changes of thermal properties in accordance with gamma-ray irradiation doses. Gamma-ray irradiation changes the morphology of the surface, and improves the wettability. In conclusion, gamma-ray irradiation will be a useful tool to control the rate of hydrolytic degradation of these PLGA films.     

Correlation of processing parameters and in situ temperatures for electron beam irradiated polycarbonate

Temperature measurements were performed for polycarbonate samples under electron beam irradiation for a total dose of 200 kGy at different dose fractionations. The samples were irradiated with a commercial electron beam accelerator and total dose was applied at different number of passes under the beam. Peak temperatures by beam heating obtained during irradiation varied significantly with different amounts of energy deposited per pass. For one-pass irradiation (200 kGy), the peak temperature recorded exceeded the polycarbonate's glass transition temperature.     

Simultaneous Enhancement of Mechanical and Dynamic Mechanical Properties of Natural Rubber/Recycled Ethylene-Propylene-Diene Rubber Blends by Electron Beam Irradiation

Mechanical and dynamic mechanical properties of natural rubber/recycled ethylene-propylene-diene rubber (NR/R-EPDM) blends were simultanoeusly enhanced by electron beam (EB) irradiation. The cross-linking promoter, trimethylolpropane triacrylate (TMPTA), was also introduced into the blends to induce the cross-linking. By applying EB irradiation, the tensile modulus, hardness, swelling, cross-link density, and storage modulus increased with increase in the irradiation dose; an irradiation dose of 50 kGy was efficient to gain optimum tensile strength. The formation of irradiation-induced cross-links after EB irradiation is a major concern for the enhancement of mechanical, swelling resistance, and dynamic mechanical properties of the blends.