Anthracene‐containing conjugated polymer showing four optical transitions upon doping: A spectroscopic study

An anthracene‐containing poly(arylene‐ethynylene)‐alt‐poly(arylene‐vinylene) (PAE‐PAV) of general constitutional unit (? Ph? C?C? Anthr? C?C? Ph? CH?CH? Anthr? CH?CH)_n bearing two 2‐ethylhexyloxy solubilizing side chains on each phenylene (Ph) unit has been synthesized and characterized. The basic electrochemical characterization was done, showing the existence of two non‐reversible oxidation and one reversible reduction peaks. The optical properties, the real and imaginary part of the dielectric function, were probed using spectroscopic ellipsometry (SE). The vibrational structure of the undoped/doped polymer was investigated using Fourier transformed infrared spectroscopy. A strong change in the polaronic absorption was observed during the doping, which after modeling revealed the existence of two separated transitions. The optical changes upon doping were additionally recorded using the SE technique. Similar to the results from FT‐IR spectroscopy, two new in‐the‐gap absorptions were found. Moreover, the electrical conductivity as well as the mobility of positive carriers were measured. In the undoped state, the conductivity of the polymer was found to be below the detection limit (<μS cm^?1), after doping the conductivity increased to 0.69 S cm^?1. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 338–346     

Polymer electrolyte membranes by in situ polymerization of poly(ethylene carbonate‐co‐ethylene oxide) macromonomers in blends with poly(vinylidene fluoride‐co‐hexafluoropropylene)

Salt‐containing membranes based on polymethacrylates having poly(ethylene carbonate‐co‐ethylene oxide) side chains, as well as their blends with poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP), have been studied. Self‐supportive ion conductive membranes were prepared by casting films of methacrylate functional poly(ethylene carbonate‐co‐ethylene oxide) macromonomers containing lithium bis(trifluorosulfonyl)imide (LiTFSI) salt, followed by irradiation with UV‐light to polymerize the methacrylate units in situ. Homogenous electrolyte membranes based on the polymerized macromonomers showed a conductivity of 6.3 × 10^?6 S cm^?1 at 20 °C. The preparation of polymer blends, by the addition of PVDF‐HFP to the electrolytes, was found to greatly improve the mechanical properties. However, the addition led to an increase of the glass transition temperature (T_g) of the ion conductive phase by ～5 °C. The conductivity of the blend membranes was thus lower in relation to the corresponding homogeneous polymer electrolytes, and 2.5 × 10^?6 S cm^?1 was recorded for a membrane containing 10 wt % PVDF‐HFP at 20 °C. Increasing the salt concentration in the blend membranes was found to increase the T_g of the ion conductive component and decrease the propensity for the crystallization of the PVDF‐HFP component. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 79–90, 2007     

Conductive triethylene glycol monomethyl ether substituted polythiophenes with high stability in the doped state

Synthesis of two conducting polymers containing 3‐hexylthiophene and 3‐[2‐(2‐(2‐methoxyethoxy)ethoxy)ethoxy]thiophene is demonstrated. In thin‐film transistors, the high‐molecular‐weight polymer shows an average mobility of 4.2 × 10^?4 cm² V^?1 s^?1. Most importantly, the polymers have high conductivity upon doping with iodine and also have high stability in the doped state with high conductivities measured even after 1 month. Furthermore, the doping causes transparency to thin films of the polymer and the films are resistant to common organic solvents. All these properties indicate a great potential for the iodine‐doped polymer to be used as an alternative to commercially available poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate). © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1079–1086     

Benzodifuran‐containing well‐defined π‐conjugated polymers for photovoltaic cells

Two well‐defined alternating π‐conjugated polymers containing a soluble electroactive benzo[1,2‐b:4,5‐b′]difuran (BDF) chromophore, poly(BDF‐(9‐phenylcarbazole)) (PBDFC), and poly(BDF‐benzothiadiazole) (PBDFBTD) were synthesized via Sonogashira copolymerizations. Their optical, electrochemical, and field‐effect charge transport properties were characterized and compared with those of the corresponding homopolymer PBDF and random copolymers of the same overall composition. All these polymers cover broad optical absorption ranges from 250 to 750 nm with narrow optical band gaps of 1.78–2.35 eV. Both PBDF and PBDFBTD show ambipolar redox properties with HOMO levels of ?5.38 and ?5.09 eV, respectively. The field‐effect mobility of holes varies from 2.9 × 10^?8 cm² V^?1 s^?1 in PBDF to 1.0 × 10^?5 cm² V^?1 s^?1 in PBDFBTD. Bulk heterojunction solar cell devices were fabricated using the polymers as the electron donor and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester as the electron acceptor, leading to power conversion efficiencies of 0.24–0.57% under air mass 1.5 illumination (100 mW cm^?2). These results indicate that their band gaps, molecular electronic energy levels, charge mobilities, and molecular weights are readily tuned by copolymerizing the BDF core with different π‐conjugated units. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and electrical conductivity of polymers containing trans-1,2-bis(9-carbazolyl)cyclobutane units

Novel poly-Schiff bases (PSB's) that contain trans-1,2-bis(9-carbazolyl)cyclobutane(DCZB) units were synthesized by the direct polycondensation of trans-1,2-bis(3-formyl-9-carbazolyl)cyclobutane with aromatic diamines in n-amyl alcohol at 160°C. Complexation of these PSB's and of poly(vinyl DCZB) (PVDCZB) with iodine produced cation-radical salts which resulted form the transfer of an electron from DCZB moieties to iodine. All the undoped polymers were insulators having electrical conductivity of the order of 10^?10–10^?12 S cm^?1 depending on the structure of polymers. By doping with iodine, the electrical conductivity increased by several orders of magnitude and reached a value of 10^?3 S cm^?1 in the case of PVDCZB and 10^?5–10^?6 S cm^?1 in the case of PSB's. The electrical conductivity of doped PSB's increased with decreasing diamine length. PVDCZB having the same iodine content per carbazole unit as poly(9-vinyl-carbazole) (PVK) has a greater electrical conductivity than PVK.     

Polymerization of β‐pinene with Schiff‐base nickel complexes catalyst: Synthesis of relatively high molecular weight poly(β‐pinene) at high temperature with high productivity

A series of easily accessible and stable Schiff‐base nickel complexes (complex 1 – 4 ) in conjunction with methylaluminoxane (MAO) were employed for the synthesis of relatively high molecular weight β‐pinene polymers at high temperature with high productivity. The ligand structure of the complex had a substantial effect on the polymerization in terms of the productivity and the molecular weight. With complex 4 in the presence of MAO, high molecular weight polymers of β‐pinene (M_n ～ 10,900) were obtained at 40 °C with an extremely high productivity up to 1.25 × 10⁷ g polyβ‐pinene/mol of Ni. ¹H NMR analyses showed that the obtained β‐pinene polymer was structurally identical to that formed by conventional cationic Lewis acid initiators. The polymerization was presumably initiated by the nickel cation formed by the reaction of the schiff‐base nickel complex and MAO, while the propagation proceeded in a manner typical for a conventional carbocationic polymerization process. Direct evidence for the carbocationic polymerization was offered by the fact that quenching of the polymerization with methanol at a low monomer conversion resulted in incorporation of a methoxyl end group into the polymer chain. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3739–3746, 2007     

Synthesis of poly(β‐pinene)‐g‐poly(meth)acrylate by the combination of living cationic polymerization and atom transfer radical polymerization

New graft copolymers of β‐pinene with methyl methacrylate (MMA) or butyl acrylate (BA) were synthesized by the combination of living cationic polymerization and atom transfer radical polymerization (ATRP). β‐Pinene polymers with predetermined molecular weights and narrow molecular weight distributions (MWDs) were prepared by living cationic polymerization with the 1‐phenylethyl chloride/TiCl₄/Ti(OiPr)₄/nBu₄NCl initiating system, and the resultant polymers were brominated quantitatively by N‐bromosuccinamide in the presence of azobisisobutyronitrile, yielding poly(β‐pinene) macroinitiators with different bromine contents (Br/β‐pinene unit molar ratio = 1.0 and 0.5 for macroinitiators a and b , respectively). The macroinitiators, in conjunction with CuBr and 2,2′‐bipyridine, were used to initiate ATRP of BA or MMA. With macroinitiator a or b , the bulk polymerization of BA induced a linear first‐order kinetic plot and gave graft copolymers with controlled molecular weights and MWDs; this indicated the living nature of these polymerizations. The bulk polymerization of MMA initiated with macroinitiator a was completed instantaneously and induced insoluble gel products. However, the controlled polymerization of MMA was achieved with macroinitiator b in toluene and resulted in the desired graft copolymers with controlled molecular weights and MWDs. The structures of the obtained graft copolymers of β‐pinene with (methyl)methacrylate were confirmed by ¹H NMR spectra. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1237–1242, 2003     

Poly(thieno[3,4‐b]‐1,4‐oxathiane) and poly(3,4‐ethylenedioxythiophene‐co‐thieno[3,4‐b]‐1,4‐oxathiane)/poly(styrene sulfonic sodium): Preparation,characterization, and optoelectronic performance

In this work, the asymmetrical analog of 3,4‐ethylenedioxythiophene (EDOT), thieno[3,4‐b]‐1,4‐oxathiane (EOTT), was synthesized and chemically polymerized first in aqueous solution using poly(styrene sulfonic sodium) (PSS) as the polyelectrolyte to yield poly(thieno[3,4‐b]‐1,4‐oxathiane) (PEOTT)/PSS. As‐formed film exhibited low electrical conductivity (～10^?4 S/cm). Alternatively, EOTT together with EDOT (in different molar ratio of 1:1 and 1:5) was copolymerized and the polymer poly(EOTT‐co‐EDOT)/PSS had electrical conductivity of 10^?1 S/cm. After dimethyl sulfoxide (DMSO) treatment, the electrical conductivity was enhanced to 10⁰ S/cm; however, the conductivity of the above homopolymer was reduced (～10^?5 S/cm). Raman spectroscopy was used to interpret conductivity enhancement or reduction after DMSO treatment. The conductivity decrease of PEOTT/PSS compared to poly(EOTT‐co‐EDOT)/PSS may arise from the conformational change of PEOTT backbone from the quasi‐planar to the distorted planar mode induced by PSS^–/PSSH through ionic interaction. Kinetic studies revealed that the copolymer had high coloration efficiencies (375 cm²/C), low switching voltages (?0.8 to +0.6 V), decent contrast ratios (45%), moderate response time (1.0 s), excellent stability, and color persistence. An electrochromic device employing poly(3‐methylthiophene) and poly(EOTT‐co‐EDOT)/PSS as the anode and cathode materials was also studied. From these results, poly(EOTT‐co‐EDOT)/PSS would be a promising candidate material for organic electronics. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2285–2297     

Chemical synthesis and characterization of poly(aniline‐co‐ethyl 3‐aminobenzoate) copolymers

Copolymers of aniline and ethyl 3‐aminobenzoate (3EAB) were synthesized by chemical polymerization in several mole ratios of aniline to functionalized aniline, and their physicochemical properties were compared to those of poly(aniline‐co‐3‐aminobenzoic acid) (3ABAPANI) copolymers. The copolymers were characterized with UV–vis, FTIR, Raman, SEM, EPR, and solid‐state NMR spectroscopy, elemental analysis, and conductivity measurements. The influence of the carboxylic acid and ester group ring substituents on the copolymers was investigated. The spectroscopic studies confirmed incorporation of 3ABA or 3EAB units in the copolymers and hence the presence of C?O group in the copolymer chains. The conductivity and EPR signals both decreased with increasing 3EAB content of the copolymers emeraldine salt (ES) form. The conductivity of the ES form of 3ABAPANI was found to be high (1.4 × 10^?1 S cm^?1) compared with the conductivity (10^?2–10^?3 S cm^?1) of 3EABPANI (ES) copolymers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1339–1347, 2010     

NONCONJUGATED CONDUCTIVE POLYMERS

Conjugation is not a prerequisite for a polymer to be conductive. A polymer must have at least one double bond in the repeat to become conductive. Interaction with a dopant (e.g., electron acceptor) causes transfer of an electron from the double bond to the dopant creating a hole at the double bond site. Electrical conduction occurs via intersite hopping of holes. Various spectroscopic methods (FTIR, optical absorption, solid-state ¹³C NMR, etc.) along with electrical measurements have been used to elucidate the mechanism of conduction in specific nonconjugated conductive polymers. Examples of these polymers include 1,4-polyisoprene which has one double bond and three single bonds in the repeat. The conductivity of polyisoprene increases 100 billion times upon doping with iodine to a maximum value of 10 S/m. Polyisoprene (natural rubber) is used nonconjugated conductive polymers have a wide range of applications in antistatics, various sensors and optoelectronics.     

Low glass transition temperature polymer electrolyte prepared from ionic liquid grafted polyethylene oxide

In this contribution, we report a new type of poly (ionic liquids) prepared by imidazolium ionic liquids directly grafting onto polyethylene oxide backbone. Different molecular weights of poly (ionic liquids) are obtained with a low glass transition temperature up to ?14 °C. The materials as polymer electrolyte achieve a high conductivity around 10^?5 S cm^?1 at 30 °C and close to 10^?3 S cm^?1 at 90 °C. High viscosity up to 4000 Pa s at room temperature would minimize the electrolytes leaking in electrochemical devices. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2104–2110     

Novel preparation of electrically conducting poly (vinyl chloride) by photo-dehydrochlorination from poly (vinyl chloride)/polypyrrole composite film

Polypyrrole (PPy) was deposited electrochemically on a platinum plate from a nitric acid solution of pyrrole. The PVC/PPy composite film was finally obtained by casting poly(vinyl chloride) (PVC) onto the PPy electrode from a tetrahydrofuran solution of PVC. The prepared composite film was irradiated at 90°C with a low-pressure mercury lamp in the stream of hydrogen gas saturated with steam, and the PVC film was dehydrochlorinated, leading to the formation of conjugated polyene. The electrical conductivity (σ) of the PVC film in the irradiated composite film was reveled: σ=2.51 × 10^?5S cm^?1. By iodine doping, σ was further enhanced up to 5.04 X 10^?3 S cm^?1. The tensile strength of the irradiated composite film became larger than that of the original PVC film; i.e., the stress at break was: 461 (composite film); 401 kg cm^?2 (PVC). These results were brought about by the doping of radical species to the conjugated polyene. The anion, NO^?₃, doped during the electrodeposition of PPy was photodecomposed to generate radical NO₂ and this species was doped to the polyene, resulting in the formation of electrically conductive PVC and mechanically improved composite film. © 1994 John Wiley & Sons, Inc.     

Improvement in carrier mobility of poly(3,4‐ethylenedioxythiophene) nanowires synthesized in porous alumina templates

Polymeric nanowires of poly(3,4‐ethylenedioxythiophene) (PEDOT) are electrochemically synthesized using porous anodic alumina oxide (AAO) membranes as templates. Four‐point resistivity measurements on more than 100 PEDOT nanowires with different diameters (50–250 nm) reveal a statistically significant size‐dependent phenomenon in which the nanowires with a smaller diameter exhibit higher conductivity. Structural characterization with Raman spectroscopy and doping level estimation with energy‐dispersive X‐ray spectrometry and X‐ray photoelectron spectroscopy indicate that the observed conductivity enhancement can be attributed to improved carrier mobility in PEDOT nanowires having an elongated conjugation structure because of the effect of the AAO template. From the estimated doping levels (～5%) and conductivity data (～100 S/cm), it is found that the carrier mobility reach 2.0 cm²/V s for the nanowire with the smallest diameter, as compared with 4.0 × 10^?4 cm²/V s for a bulk PEDOT film. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

New Additions to Nonconjugated Conductive Polymers; Nonlinear Optical Effects

Recently, new additions to nonconjugated conductive polymers have been made that include: poly(β-pinene), poly(ethylenepyrrolediyl) derivative and polynorbornene. These polymers have different double-bond number fractions per repeat compared to previously reported nonconjugated conductive polymers. Upon doping with electron acceptor (e.g. iodine) the conductivities increase more than ten orders of magnitude to levels consistent with their double-bond number fractions. Radical cations that are formed upon doping have dimensions less than a nanometer leading to unexpectedly large nonlinear optical effects. The measured Kerr coefficient of doped polyisoprene is ～1.6 × 10^-10 m/V² at 633 nm. For doped poly(β-pinene) the Kerr coefficient is ～1.2 × 10^-10 m/V² and for poly(ethylenepyrrolediyl) derivative it is ～1.2 × 10^-9m/V². Exceptionally large two-photon absorption coefficient (～2.6 cm/MW at 810 nm) has been measured for doped poly(β-pinene). The mechanism of the nonlinear optical effect has been explained using a model of subnanometer size metallic quantum dots. These novel materials with wide transparency are expected to have significant applications in photonics.     

Synthesis and ionic conductivity of hyperbranched poly(glycidol)

A novel hyperbranched poly(glycidol) (HPG) was prepared and characterized. The synthesized HPG was used as a substrate of a polymer electrolyte. The ionic conductivity of a blend of HPG, polyurethane (PU), and salt was studied. The ionic conductivity of HPG/PU/LiClO₄ was about 6.6 × 10^?6 S · cm^?1 at 20 °C and 6.3 × 10^?4 S · cm^?1 at 60 °C. The results indicated that HPG showed higher solubility for salt than linear polyether when both had the same [O]/[Li⁺] molar ratio. The main reason was that more cavities and a lower degree of chain entanglement in HPG resulted in a lower glass‐transition temperature and were beneficial for decreasing the aggregation of salt or enhancing the ionic conductivity. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2225–2230, 2001     

Poly(tetrafluorostyrenephosphonic acid)–polysulfone block copolymers and membranes

A series of ionic ABA triblock copolymers having a central polysulfone (PSU) block and poly(2,3,5,6,‐tetrafluorostyrene‐4‐phosphonic acid) (PTFSPA) outer blocks with different lengths were prepared and studied as electrolyte membranes. PSU with terminal benzyl bromide was used as a bifunctional macroinitiator for the formation of poly(2,3,4,5,6‐pentafluorostyrene) (PPFS) blocks by atom transfer radical polymerization. Selective and complete phosphonation of the PPFS blocks was achieved via a Michaelis?Arbuzov reaction using tris(trimethylsilyl)phosphite at 170 °C. Copolymer films were cast from solution and subsequently fully hydrolyzed to produce transparent flexible proton conducting PTFSPA‐b‐PSU‐b‐PTFSPA membranes with a thermal stability reaching above 270 °C under air, and increasing with the PTFSPA content. Studies of thin copolymer electrolyte membranes by tapping mode atomic force microscopy showed phase separated morphologies with continuous proton conducting PTFSPA nano scale domains. Block copolymer membranes reached a proton conductivity of 0.08 S cm^?1 at 120 °C under fully hydrated conditions, and 0.8 mS cm^?1 under 50% relative humidity at 80 °C. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4657–4666     

Interaction of water in polymers: Poly(ethylene‐co‐vinyl acetate) and poly(vinyl acetate)

We studied the interaction of water in poly(ethylene‐co‐vinyl acetate) of various vinyl acetate compositions and poly(vinyl acetate), on the basis of the infrared spectrum of the water dissolved therein. The spectrum shows a very sharp and distinct band at about 3690 cm^?1 (named as A), and less‐sharp two bands around 3640 (B) and 3550 cm^?1 (C), the A band being outstanding especially at a low vinyl acetate composition. As the vinyl acetate composition increases, the A band decreases in intensity relative to the C band, whereas the B band increases contrarily. Analysis of the spectral change has elucidated that one‐bonded water (of which one OH is hydrogen‐bonded to the C?O of an ester group and the other OH is free) and two‐bonded water (each OH of which is hydrogen‐bonded to one C?O) coexist in the copolymer and that two‐bonded water increases in relative population with increasing vinyl acetate composition. Dissolved water is entirely two‐bonded in poly(vinyl acetate), in which C?O groups are densely distributed in the matrix. We proved that dissolved water in polymers is hydrogen‐bonded through one or two OH groups to the possessed functional groups but does not cluster. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 777–785, 2005     

Photoinitiated thermolysis of poly(phenylenevinylene) precursor and photochemical doping of poly(phenylenevinylene)

The photoinitiated elimination of methoxy groups of poly(p-phenylene-1-methoxyethylene) and the photochemical doping of the resulting poly(phenylenevinylene) (PPV) were investigated. Upon irradiation and then heat treatment at 150°C, poly(p-phenylene-1-methoxyethylene) containing triphenylsulfonium hexafluoroantimonate was converted to PPV. The resulting PPV was observed to be conductive, and its conductivity was 10⁻²–10⁻³ S/cm. By a lithographic procedure, we produced a conducting pattern doped photochemically in a nonconjugated poly(p-phenylene-1-methoxyethylene) matrix.     

Electrochemical Treatment for Effectively Tuning Thermoelectric Properties of Free‐Standing Poly(3‐methylthiophene) Films

The degree of oxidation of conducting polymers has great influence on their thermoelectric properties. Free‐standing poly(3‐methylthiophene) (P3MeT) films were prepared by electrochemical polymerization in boron trifluoride diethyl etherate, and the fresh films were treated electrochemically with a solution of propylene carbonate/lithium perchlorate as mediator. The conductivity of the resultant P3MeT films depends on the doping level, which is controlled by a constant potential from ?0.5 to 1.4 V. The optimum electrical conductivity (78.9 S cm^?1 at 0.5 V) and a significant increase in the Seebeck coefficient (64.3 μV K^?1 at ?0.5 V) are important for achieving an optimum power factor at an optimal potential. The power factor of electrochemically treated P3MeT films reached its maximum value of 4.03 μW m^?1 K^?2 at 0.5 V. Moreover, after two months, it still exhibited a value of 3.75 μW m^?1 K^?2, and thus was more stable than pristine P3MeT due to exchange of doping ions in films under ambient conditions. This electrochemical treatment is a significant alternative method for optimizing the thermoelectric power factor of conducting polymer films.     

Synthesis and characterization of novel nano size electroactive poly 4,4′‐diaminodiphenyl sulphone

The modification of electrodeposited polyaniline film by subsequent electrodeposition of 4,4′‐diaminodiphenyl sulfone (DDS) leads to a new material having nanostructure. The coated polymer films were treated with various pH solutions. The film adherent characteristics and surface morphology were studied using SEM. The electrochemically synthesized polyDDS revealed good redox behavior. The DDS was also polymerized by the chemical oxidation method using potassium persulphate. The polymer was characterized by UV‐Vis and FTIR spectral studies. The formation of polymer through the N? H group was understood from the single N? H stretching vibrational frequency at 3459 cm^?1. The X‐ray diffraction studies revealed the formation of nano sized (28 nm) crystalline polymer. The conductivity of the polymer was determined to be 1.07 × 10^?4 S.cm^?1. The solubility of the chemically polymerized powder was ascertained, and polyDDS showed good solubility in DMF and DMSO. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1702–1707, 2005