Two‐dimensional Fourier transform infrared spectroscopy study of biosynthesized poly(hydroxybutyrate‐co‐hydroxyhexanoate) and poly(hydroxybutyrate‐ co‐hydroxyvalerate)

Generalized two‐dimensional (2D) Fourier transform infrared correlation spectroscopy was used to investigate the effect of the comonomer compositions on the crystallization behavior of two types of biosynthesized random copolymers, poly(hydroxybutyrate‐co‐hydroxyhexanoate) and poly(hydroxybutyrate‐co‐hydroxyvalerate). The carbonyl absorption band around 1730 cm^?1 was sensitive to the degree of crystallinity. 2D correlation analysis demonstrated that the 3‐hydroxyhexanoate units preferred to remain in the amorphous phase of the semicrystalline poly(hydroxybutyrate‐co‐hydroxyhexanoate) copolymer, resulting in decreases in the degree of crystallinity and the rate of the crystallization process. The poly(hydroxybutyrate‐co‐hydroxyvalerate) copolymer maintained a high degree of crystallinity when the 3‐hydroxyvalerate fraction was increased from 0 to 25 mol % because of isodimorphism. The crystalline and amorphous absorption bands for the carbonyl bond for this copolymer, therefore, changed simultaneously. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 649–656, 2002; DOI 10.1002/polb.10126     

Light‐emitting copolymers based on fluorene and selenophene—Comparative studies with its sulfur analogue: Poly(fluorene‐co‐thiophene)

A series of soluble conjugated copolymers derived from 9,9‐dioctylfluorene (FO) and selenophene (SeH) was synthesized by a palladium‐catalyzed Suzuki coupling reaction with various feed ratios of SeH to FO less than or equal to 50%. The efficient energy transfer from fluorene segments to narrow band‐gap selenophene sites was observed. In comparison with the very well studied copolymer poly(fluorene‐co‐thiophene), poly(9,9‐dioctylfluorene‐co‐selenophene) (PFO‐SeH) shows redshifted photoluminescence (PL) and electroluminescence (EL) emission. PL spectra of the PFO‐SeH copolymers show a significant redshift along with increasing selenophene content in the copolymers and also with increasing polymer concentration in solution. PL quantum efficiency of the selenophene‐containing PFO copolymer is much lower than that of corresponding PFO‐thiophene (Th) copolymers. All these features of PFO‐SeH copolymers can be explained by the difference in aromaticity of selenophene and thiophene heterocycles and the heavy atom effect of Se in comparison with S‐atoms. The device fabricated with PFO‐SeH15 as the emissive layer exhibited high external quantum efficiency (0.51%) at a luminance of 1570 cd/m². Device performance is limited by electron injection and the strong quenching effect of Se atoms. Devices with PFO‐SeH copolymers blended into PFO homopolymers show significant improvement in device performance. External quantum efficiency as high as 1.7% can be obtained for PFO‐SeH30/PFO blend devices. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 823–836, 2005     

A thermodynamic analysis of specific interactions in homoblends of poly(styrene‐co‐4‐vinylpyridine) and poly(styrene‐co‐methacrylic acid)

Miscibility and strong specific interactions that occurred within homoblends of poly(styrene‐co‐4‐vinylpyridine) containing 15 mol % of 4‐vinylpyridine (PS4VP15) and poly(styrene‐co‐methacrylic acid) containing 15 mol % of methacrylic acid (PSMA15) have been examined by Fourier Transform infrared spectroscopy and DSC. The observed positive deviation of the glass transition temperature of the blends from the linear average line, was analyzed by the frequently used theoretical conventional approaches including the one very recently proposed by Brostow. A better fit was obtained when this latter is used. A reasonable agreement with experimental values was also obtained when the theoretical fitting parameter free method developed by Coleman, is applied to predict the composition dependence of the T_g of this system. A thermodynamic analysis of hydrogen bonding in this system was carried using the Painter‐Coleman association model and the variation of the Gibbs function of mixing and its different contributions and corresponding phase diagrams as a function of temperature and composition were estimated. This analysis predicted PSMA15 to be miscible with PS4VP15 in the whole composition range up to 150 °C. Above this temperature, a partial miscibility is predicted when the PS4VP15 is in excess. The DSC results are in agreement with these predictions. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 923–931, 2009     

Morphology of poly(butylene terephthalate)–poly(ethylene terephthalate‐co‐isophthalate‐co‐sebacate) segmented copolyesters

Segmented copolyesters, namely, poly(butylene terephthalate)–poly(ethylene terephthalate‐co‐isophthalate‐co‐sebacate) (PBT‐PETIS), were synthesized with the melting transesterification processing in vacuo condition involving bulk polyester produced on a large scale (PBT) and ternary amorphous random copolyester (PETIS). Investigations on the morphology of segmented copolyesters were undertaken. The two‐phase morphology model was confirmed by transmission electron microscopy and dynamic mechanical thermal analysis. One of the phases was composed of crystallizable PBT, and the other was a homogeneous mixture of PETIS and noncrystallizable PBT. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2257–2263, 2003     

A thermodynamic analysis of specific interactions in blends of poly(styrene‐co‐N,N‐dimethylacrylamide) and poly(styrene‐co‐acrylic acid). Screening and self‐association effects

In a first step of this contribution, the observed glass transition temperature‐composition behavior of miscible blends of poly(styrene‐co‐N,N‐dimethylacrylamide) (SAD17) containing 17 mol % of N,N‐dimethylacrylamide and poly(styrene‐co‐acrylic acid) (SAA18, SAA27, and SAA32) containing increasing acrylic acid content, are analyzed according to theoretical approaches. Both Kwei and Brostow equations describe well the experimental data though better fits were obtained with the Brostow's approach. The specific interactions involved in these systems are a combination of intra and interassociation hydrogen bonding. The positive deviation from the linear mixing rule of T_g‐composition observed within the SAA18+SAD17 blend system, indicates that interassociation interactions are prevailing. More pronounced intra‐association interactions within the SAA32+SAD17 blend system led to a large negative deviation while a fine balance is established between these two types of interactions within the SAA27+SAD17 blend. A thermodynamic analysis was carried out according to the Painter‐Coleman association model. The miscibility and phase behavior of SAD17+SAA18 and SAD17+SAA27 blends are well predicted. However, this model predicts a partial miscibility of SAD17+SAA32 system. Finally, the fitting parameter free method developed by Coleman to predict the T_g‐composition behavior is applied. This method predicts fairly well the evolution trend of experimental T_gs of the SAA18+SAD17 and SAA27+SAD17 blend systems. However, the compositional dependence of SAA32+SAD17 blend T_g was not predictable by this method. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47:2074–2082, 2009     

Electrospun fiber mats of poly(3‐hydroxybutyrate), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate), and their blends

Electrospinning of poly(3‐hydroxybutyrate) (PHB), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV), and their blends was first carried out in chloroform at 50 °C on a stationary collector. The average diameter of the as‐spun fiber from PHB and PHBV solutions decreased with increasing collection distance and increased with increasing solution concentration and applied electrical potential. In all of the spinning conditions investigated, the average diameter of the as‐spun pure fibers ranged between 1.6 and 8.8 μm. Electrospinning of PHB, PHBV, and their blends was carried out further at a fixed solution concentration of 14% w/v on a homemade rotating cylindrical collector. Well‐aligned, cross‐sectionally round fibers without beads were obtained. The average diameter of the as‐spun pure and blend fibers ranged between 2.3 and 4.0 μm. The as‐spun fiber mats appeared to be more hydrophobic than the corresponding films and much improvement in the tensile strength and the elongation at break was observed for the blend fiber mats over those of the pure fiber ones. Lastly, indirect cytotoxicity evaluation of the as‐spun pure and blend fiber mats with mouse fibroblasts (L929) indicated that these mats posed no threat to the cells. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2923–2933, 2006     

Synthesis of poly[(2‐oxo‐1,3‐dioxolane‐ 4‐yl)methyl methacrylate‐co‐styrene] by addition reaction of carbon dioxide and its compatibility with poly(methyl methacrylate) or poly(vinyl chloride)

We investigated the chemical fixation of carbon dioxide (CO ₂) to a copolymer bearing epoxide and the application of the cyclic carbonate group containing copolymer to polymer blends. In the synthesis of poly[(2‐oxo‐1,3‐dioxolane‐4‐yl)methyl methacrylate‐co‐styrene] [poly(DOMA‐co‐St)] from the addition of CO ₂ to poly(glycidyl methacrylate‐co‐styrene) [poly(GMA‐co‐St)], quaternary ammonium salts showed good catalytic activity at mild reaction conditions. The CO ₂ addition reaction followed pseudo first‐order kinetics with the concentration of poly(GMA‐co‐St). In order to expand the applications of the CO ₂ fixed copolymer, polymer blends of this copolymer with poly(methyl methacrylate) (PMMA) or poly(vinyl chloride) (PVC) were cast from N,N′‐dimethylformamide (DMF) solution. Miscibility of blends of poly(DOMA‐co‐St) with PMMA or PVC have been investigated both by differential scanning calorimetry (DSC) and visual inspection of the blends, and the blends were miscible over the whole composition ranges. The miscibility behaviors were also discussed in terms of FT‐IR spectra. Copyright © 2002 John Wiley & Sons, Ltd.     

Relationship among drug delivery behavior,degradation behavior and morphology of copolylactones derived from glycolide,l‐lactide and ε‐caprolactone

A series of copolylactones was synthesized by ring‐opening copolymerization of glycolide, L ‐lactide and ?‐caprolactone, using stannous octoate as catalyst. The in vitro degradation behaviors of them were studied and data demonstrated different degradation rates which mainly depended on the compositions. Investigation of the 5‐fluorouracil (5‐Fu) release from these copolylactones revealed that the composition, degradation rate and the morphology of the polymeric matrix played an important role on the drug release kinetics. A sustained 5‐Fu release without initial time lag was obtained from random poly(lactide‐co‐glycolide‐co‐caprolactone) (r‐PGLC) drug carrier, and it differed from the cases of polylactide (PLA) or random poly(lactide‐co‐glycolide) (PLGA), which usually showed an initial time lag or biphasic drug release behavior. It was due to the low glass transition temperature (T _g) of the r‐PGLC and the drug would diffuse faster in rubbery state under the experimental temperature. Furthermore, a significant change in the drug release behavior of r‐PGLC was observed when the temperatures were changed around the T _g of the drug carrier, which implied that the drug release behavior could be regulated by adjusting the morphology of the drug carrier. Copyright © 2002 John Wiley & Sons, Ltd.     

Biocompatibility evaluation of self‐assembled micelles prepared from poly(lactide‐co‐glycolide)‐poly(ethylene glycol) diblock copolymers

In this work, a series of PLGA‐PEG diblock copolymers were synthesized by ring‐opening polymerization of L‐lactide and glycolide using mPEG as macroinitiator and stannous octoate as catalyst. Spherical micelles were obtained from the various copolymers by using co‐solvent evaporation method. The biocompatibility of micelles was evaluated with the aim of assessing their potential in the development of drug delivery systems. Various aspects of biocompatibility were considered, including MTT assay, agar diffusion test, release of cytokines, hemolytic test, dynamic clotting time, protein adsorption in vitro, and zebrafish embryonic compatibility in vivo. The combined results revealed that the micelles present good cytocompatibility and hemocompatibility in vitro. Moreover, the cumulative effects of micelles throughout embryos developing stages have no toxicity in vivo. It is thus concluded that micelles prepared from PLGA‐PEG copolymers present good biocompatibility as potential drug carrier.     

Synthesis of high‐molecular‐weight aliphatic–aromatic copolyesters from poly(ethylene‐co‐1,6‐hexene terephthalate) and poly(L‐lactic acid) by chain extension

A series of aliphatic–aromatic multiblock copolyesters consisting of poly(ethylene‐co‐1,6‐hexene terephthalate) (PEHT) and poly(L ‐lactic acid) (PLLA) were synthesized successfully by chain‐extension reaction of dihydroxyl terminated PEHT‐OH prepolymer and dihydroxyl terminated PLLA‐OH prepolymer using toluene‐2,4‐diisoyanate as a chain extender. PEHT‐OH prepolymers were prepared by two step reactions using dimethyl terephthalate, ethylene glycol, and 1,6‐hexanediol as raw materials. PLLA‐OH prepolymers were prepared by direct polycondensation of L ‐lactic acid in the presence of 1,4‐butanediol. The chemical structures, the molecular weights and the thermal properties of PEHT‐OH, PLLA‐OH prepolymers, and PEHT‐PLLA copolymers were characterized by FTIR, ¹H NMR, GPC, TG, and DSC. This synthetic method has been proved to be very efficient for the synthesis of high‐molecular‐weight copolyesters (say, higher than M_w = 3 × 10⁵ g/mol). Only one glass transition temperature was found in the DSC curves of PEHT‐PLLA copolymers, indicating that the PLLA and PEHT segments had good miscibility. TG curves showed that all the copolyesters had good thermal stabilities. The resulting novel aromatic–aliphatic copolyesters are expected to find a potential application in the area of biodegradable polymer materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5898–5907, 2009     

Synthesis and properties of poly(isobutyl methacrylate‐co‐butanediol dimethacrylate‐co‐methacryl polyhedral oligomeric silsesquioxane) nanocomposites

Poly[isobutyl methacrylate‐co‐butanediol dimethacrylate‐co‐3‐methacrylylpropylheptaisobutyl‐T8‐polyhedral oligomeric silsesquioxane] [P(iBMA‐co‐BDMA‐co‐MA‐POSS)] nanocomposites with different crosslink densities and different polyhedral oligomeric silsesquioxane (MA‐POSS) percentages (5, 10, 15, 20, and 30 wt %) were synthesized by radical‐initiated terpolymerization. Linear [P(iBMA‐co‐MA‐POSS)] copolymers were also prepared. The viscoelastic properties and morphologies were studied by dynamic mechanical thermal analysis, confocal microscopy, and transmission electron microscopy (TEM). The viscoelastic properties depended on the crosslink density. The dependence of viscoelastic properties on MA‐POSS content at a low BDMA loading (1 wt %) was similar to that of linear P(iBMA‐co‐MA‐POSS) copolymers. P(iBMA‐co‐1 wt % BDMA‐co‐10 wt % MA‐POSS) exhibited the highest dynamic storage modulus (E′) values in the rubbery region of this series. The 30 wt % MA‐POSS nanocomposites with 1 wt % BDMA exhibited the lowest E′. However, the E′ values in the rubbery region for P(iBMA‐co‐3 wt % BDMA‐co‐MA‐POSS) nanocomposites with 15 and 30 wt % MA‐POSS were higher than those of the parent P(iBMA‐co‐3 wt % BDMA) resin. MA‐POSS raised the E′ values of all P(iBMA‐co‐ 5 wt % BDMA‐co‐MA‐POSS) nanocomposites in the rubbery region above those of P(iBMA‐co‐5 wt % BDMA), but MA‐POSS loadings < 15 wt % had little influence on glass‐transition temperatures (T_g's) and slightly reduced T_g values with 20 or 30 wt % POSS. Heating history had little influence on viscoelastic properties. No POSS aggregates were observed for the P(iBMA‐co‐1 wt % BDMA‐co‐MA‐POSS) nanocomposites by TEM. POSS‐rich particles with diameters of several micrometers were present in the nanocomposites with 3 or 5 wt % BDMA. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 355–372, 2005     

Homopolymerizations and random copolymerizations of olefins with amino‐substituted cyclopentadienylchromium complexes

1‐(2‐N,N‐Dimethylaminoethyl)‐2,3,4,5‐tetramethylcyclopentadienyl‐chromium dichloride ( 1 ), (2‐N,N‐dimethylaminoethyl)cyclopentadienylchromium dichloride ( 6 ), and (2‐N,N‐dimethylaminoethyl)indenylchromium dichloride ( 7 ) in the presence of modified methylaluminoxane exhibit high catalytic activities for the polymerization of ethylene with random copolymerizations of ethylene with propylene, ethylene with 1‐hexene, and propylene with 1‐hexene. These initiators conduct polymerizations to give high molecular weight polymers with low polydispersities. However, the stereoregularities are very poor in these reactions. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2759–2771, 2002     

Water‐disintegrative and biodegradable blends containing poly(L‐lactic acid) and poly(butylene adipate‐co‐terephthalate)

In this study, novel biodegradable materials were successfully generated, which have excellent mechanical properties in air during usage and storage, but whose structure easily disintegrates when immersed in water. The materials were prepared by melt blending poly(L ‐lactic acid) (PLLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) with a small amount of oligomeric poly(aspartic acid‐co‐lactide) (PAL) as a degradation accelerator. The degradation behavior of the blends was investigated by immersing the blend films in phosphate‐buffered saline (pH = 7.3) at 40 °C. It was shown that the PAL content and composition significantly affected morphology, mechanical properties, and hydrolysis rate of the blends. It was observed that the blends containing PAL with higher molar ratios of L ‐lactyl [LA]/[Asp] had smaller PBAT domain size, showing better mechanical properties when compared with those containing PAL with lower molar ratios of [LA]/[Asp]. The degradation rates of both PLLA and PBAT components in the ternary blends simultaneously became higher for the blends containing PAL with higher molar ratios of [LA]/[Asp]. It was confirmed that the PLLA component and its decomposed materials efficiently catalyze the hydrolytic degradation of the PBAT component, but by contrast that the PBAT component and its decomposed materials do not catalyze the hydrolytic degradation of the PLLA component in the blends. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Nanofibrosis of uncrystallizable poly(lactide‐co‐glycolide) via phase separation

Poly(lactide‐co‐glycolide) (PLGA) copolymers are a kind of biocompatible and biodegradable materials being widely used in tissue engineering. However, phase separation had not been reported successfully in fabricating these amorphous polymers into nanofibrous matrix, although this technique had shown advantages over electrospinning in producing a nanofiber network. In this study, tetrahydrofuran (THF)/H₂O solvent pairs were found suitable solvents to induce the formation of uniform PLGA gel at selected gelation temperatures. The results indicated that fine nanofibrous structures with fiber diameter around 40–60 nm could be obtained following the steps of gel formation, solvent extraction, and freeze‐drying, by controlling the concentration of PLGA/THF/H₂O solution, THF/H₂O ratio, and gelation temperature. Copyright © 2009 John Wiley & Sons, Ltd.     

Morphology and thermal properties of poly(L‐lactide)/poly(butylene succinate‐co‐butylene adipate) compounded with twice functionalized clay

Poly(L ‐lactide) (PLLA)/poly(butylene succinate‐co‐butylene adipate) (PBSA) blends were compounded with Cloisite 25A® (C25A) and C25A functionalized with epoxy groups, respectively. Epoxy groups on the surface of C25A were introduced by treating C25A with (glycidoxypropyl)trimethoxy silane (GPS) to produce so called Twice Functionalized Organoclay (TFC). Variation of morphology and properties of PLLA/PBSA/C25A composites was investigated before and after the treatment with GPS. The morphological structure of the composites was analyzed by using X‐ray diffractometry (XRD) and transmission electron microscopy (TEM). The silicate layers of PLLA/PBSA/TFC were exfoliated to a larger extent than PLLA/PBSA/C25A. Incorporation of the epoxy groups on C25A improved significantly elongation at break as well as tensile modulus and tensile strength of PLLA/PBSA/C25A. The larger amount of exfoliation of the silicate layers in PLLA/PBSA/TFC as compared with that in PLLA/PBSA/C25A was attributed to the increased interfacial interaction between the polyesters and the clay due to chemical reaction. Thermo gravimetric analysis revealed that both T_5%, which was the temperature corresponding to 5% weight loss, and activation energy of thermal decomposition of PLLA/PBSA/TFC were far superior to those of PLLA/PBSA/C25A as well as to those of PLLA/PBSA, indicating that the composites with exfoliated silicate layers were more thermally stable than those with intercalated silicate layers. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 478–487, 2005     

One‐step synthesis of poly(lactic‐co‐glycolic acid)‐g‐poly‐1‐vinylpyrrolidin‐2‐one copolymers

The radical polymerization of 1‐vinylpyrrolidin‐2‐one (NVP) in poly(lactic‐co‐glycolic acid) (PLGA) 50:50 at 100 °C leads to amphiphilic PLGA‐g‐PVP copolymers. Their composition is determined by FT‐IR spectroscopy. Thermogravimetric analyses agree with FT‐IR determinations. Saponification of the PLGA‐g‐PVP polyester portion allows isolating the PVP side chains and measuring their molecular weight, from which the average chain transfer constant (C_T) of the PLGA units is estimated. The MALDI‐TOF spectra of PVP reveal the presence at one chain end of residues of either glycolic acid‐ or lactic acid‐ or lactic/glycolic acid dimers, trimers and one tetramer, the other terminal being hydrogen. This unequivocally demonstrates that grafting occurred. Accordingly, the orthogonal solvent pair ethyl acetate—methanol, while separating the components of PLGA/PVP intimate mixtures, fails to separate pure PVP or PLGA from the reaction products. All PLGA‐g‐PVP and PLGA/PLGA‐g‐PVP blends, but not PLGA/PVP blends, give long‐time stable dispersions in water. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1919–1928     

Investigation of the deformation of homogeneous poly(ethylene‐co‐1‐octene) by wide‐ and small‐angle X‐ray scattering using synchrotron radiation

The deformation behavior of homogeneous ethylene‐1‐octene copolymers was investigated as a function of the crystallinity and the crystal size and perfection, respectively, by wide‐ and small‐angle X‐ray scattering using synchrotron radiation. The crystallinity and the crystal size and perfection, respectively, are controlled by the copolymer composition and the condition of melt crystallization. The deformation includes rotation of crystals, followed by plastic deformation and complete melting of the initial crystal population, and final formation of microfibrils. The process of rotation, plastic deformation, and melting of crystals of the initial structure is completed at lower strain if the size and perfection of the crystals, respectively, decrease, that is, if crystals thermally melt at lower temperature. The kinetics of the fibrillation of the initial structure seems independent of the crystal symmetry, that is, rotation and melting of pseudohexagonal and orthorhombic polyethylene crystals (as evident in low‐crystalline specimens) are similar. The structure of the microfibrils, before and after stress release, is almost independent of the condition of prior melt crystallization, which supports the notion of complete melting of the initial crystal population. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1919–1930, 2002     

Synthesis and non‐isothermal crystallization kinetics of poly(ethylene terephthalate)‐co‐poly(propylene glycol) copolymers

Poly(ethylene terephthalate)‐co‐poly(propylene glycol) (PET‐co‐PPG) copolymers with PPG ratio ranging from 0 to 0.90 mol% were synthesized by the melt copolycondensation. The intrinsic viscosity, structure, non‐isothermal crystallization behavior, nucleation and spherulitic growth of the copolymers were investigated by Ubbelohde viscometer, Proton Nuclear Magnetic Resonance (¹H‐NMR), differential scanning calorimetry, and polarized optical microscopy, respectively. The non‐isothermal crystallization process of the copolymers was analyzed by Avrami, Ozawa, Mo's, Kissinger, and Dobreva methods, respectively. The results showed that the crystallizability of PET was apparently enhanced with incorporating a small amount of PPG, which first rose and then reduced with increasing amount of PPG in the copolymers at a given cooling rate. The crystallization mechanism was a three‐dimensional growth with both instantaneous and sporadic nucleation. Particularly, PET‐co‐PPG containing 0.60 mol% PPG exhibited the highest crystallizability among all the copolymers. Copyright © 2015 John Wiley & Sons, Ltd.     

Solid‐state NMR characterizations on phase structures and molecular dynamics of poly(ethylene‐co‐vinyl acetate)

Solid‐state nuclear magnetic resonance spectroscopy and relaxation measurements, together with DSC, have been used to elucidate the structures and molecular dynamics in poly(ethylene‐co‐vinyl acetate) (EVA). It has been found that besides immobile orthorhombic and monoclinic crystalline phases, the third mobile crystalline phase (possibly the phase) of a considerable amount (36% of total crystalline phases) appears in the EVA samples, which forms during room‐temperature aging as a result of the secondary crystallization and melts at temperature somewhat higher than room temperature. Such a mobile crystalline phase has not only the well‐defined chemical shift of its own, but also has different molecular mobility from the orthorhombic phase. The mobile crystalline phase is characterized by the rapid relaxation of the longitudinal magnetization, which is caused by conventional spin‐lattice relaxation, while the slow relaxation of the longitudinal magnetization occurring in the orthorhombic phase is originated from the chain diffusion. In addition, the amorphous phase also contains two components: an interfacial amorphous phase and a melt‐like amorphous phase. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2864–2879, 2006     

Parameters affecting transition temperatures of poly(lactic acid‐co‐polydiols) copolymer‐based polyester urethanes and their shape memory behavior

A series of polyester urethanes (PEUs) comprising poly(lactic acid‐co‐polydiol) copolymers as a soft segment, 4,4′‐diphenylmethane diisocyanate (MDI) and 1,4‐butanediol (BDO) as a hard segment were systematically synthesized. Soft segments, which were block copolymers of L ‐lactide (LA) and polydiols such as poly(ethylene glycol) and poly(trimethylene ether glycol), were prepared via ring opening polymerization. Glass transition temperatures (T_g) of the obtained PEUs were found strongly dependent on properties of copolymer soft segments. By simply changing composition ratio, type and molecular weight of polydiols in the soft segment preparation step, T_g of PEU can be varied in the broad range of 0–57°C. The synthesized PEUs exhibited shape memory behavior at their transition temperatures. PEUs with hard segment ratio higher than 65 mole percent showed good shape recovery. These findings suggested that it is important to manipulate molecular structure of the copolymer soft segment for a desirable transition temperature and design optimal soft to hard segment ratio in PEU for good shape recovery. Copyright © 2011 John Wiley & Sons, Ltd.