2′-甲基丙烯酰氧基-3α-甲基丙烯酰基胆酸乙酯固化动力学研究

根据文献合成了含有两个双键的胆酸衍生物—2′-甲基丙烯酰氧基-3α-甲基丙烯酰基胆酸乙酯(CAGE2MA),采用非等温DSC法和等温DSC法研究其固化反应。采用Kissinger法处理非等温DSC数据得到动力学数据:Ea=90.16kJ/mol、lnA=21.97和n=0.936。通过积分等转化率法及自催化动力学模型分别处理等温固化DSC数据,前者表明随着反应的进行,Ea和lnA值逐渐减小;后者表明固化温度越高,自催化曲线与实验数据拟合得越好,在高转化率阶段,实验数据与拟合曲线出现偏差。     

N,N,N′,N′-四炔丙基-4,4′-二氨基-二苯甲烷与4,4′-联苯二苄叠氮固化动力学研究

分别利用FTIR和DSC技术对由N,N,N,′N′-四炔丙基-4,4′-二氨基-二苯甲烷(TPDDM)与4,4′-联苯二苄叠氮(BAMBP)形成的一种新型三唑树脂的固化反应及其动力学进行了研究.TPDDM与BAMBP通过1,3-偶极环加成反应形成三唑五元环结构的聚合物,固化起始温度约为70℃,体系在较低温度下即可固化.反应体系的固化反应是一级反应,采用DSC法与FTIR法分别获得了表观聚合反应动力学参数,其结果具有一定的可比性.     

非等温法研究TGDDM/DDS体系固化反应动力学

采用DSC对4,4′-四缩水甘油基二氨基二苯基甲烷(TGDDM)和3,3′-二氨基二苯基砜(DDS)体系的固化反应动力学进行了研究.分别通过n级反应法和Malek的最大概然机理函数法确定了固化反应机理函数,求解了固化反应动力学参数,得到了固化反应动力学模型.结果表明,通过Kissinger,Crane方法求解动力学参数所得到的n级反应模型与实验值差别较大;而采用Malek方法判别机理,表明该固化反应按照自催化反应机理进行,实验得到的DSC曲线与模型计算所得到的曲线吻合的较好,所确立的模型在5~20K/min的升温速率下能较好地描述TGDDM/DDS体系的固化反应过程,并为工艺参数的选择和工艺窗口的优化提供了理论依据.     

液态聚碳硅烷的固化反应动力学研究

选用过氧化二异丙苯(DCP)和偶氮二异丁腈(AIBN)分别引发含乙烯基液态聚碳硅烷(VHPCS)聚合。采用非等温差示扫描量热法(DSC)研究VHPCS/DCP、VHPCS/AIBN两种体系的固化反应动力学,通过Kissinger方程和Crane方程确定相关动力学参数,并由此得出体系的n级固化模型。同时通过β-T外推法确定体系的固化工艺温度,并对体系交联机理及产物热性能进行分析。研究结果表明:VHPCS/DCP、VHPCS/AIBN二体系的活化能分别为72.17kJ/mol、94.11kJ/mol,反应级数分别为0.92、0.93。β-T外推法确定:当升温速率为0℃/min时二体系的近似凝胶化温度均为55℃,峰值温度分别为110℃、107℃,终止温度分别为129.5℃、134℃。FTIR结果表明,VHPCS的交联固化主要是通过双键的自聚合实现,交联后样品的陶瓷产率有所提高。     

2,4,6-三(羟基苯甲基氨基)-均三嗪的合成及其与双酚A型环氧树脂的固化行为研究

合成了一种含三嗪环结构的环氧树脂固化剂2,4,6-三(羟基苯甲基氨基)-均三嗪(MFP).用动态DSC和原位红外光谱对MFP/DGEBA(双酚A型环氧树脂)体系的固化行为进行了研究.动态DSC研究表明,由于MFP分子结构中存在两种活泼氢(酚羟基氢和仲胺氢),固化反应存在明显的两个峰,相对应的表观活化能分别为70.5 kJ.mol-1和86.5 kJ.mol-1(Kissinger法),通过与另一相似化合物固化DGEBA的比较可知,在MFP固化DGEBA的过程中,酚羟基与环氧基反应相对较难.原位红外动力学结果很好地支持了上述结论.     

升温与等温法非模型动力学研究环氧树脂固化反应

基于DSC数据,采用以Vyazovkin积分法为基础的升温法非模型动力学和等温法非模型动力学对双酚A型环氧树脂E51/4,4′-二氨基二苯基砜(DDS)体系及多官能度环氧树脂AG80/DDS体系的固化过程进行了研究,并结合玻璃化转变温度的变化和原位红外测试技术,对比分析了升温与等温条件下的固化反应规律.结果表明,与传统的模型拟合法相比,非模型动力学更适合定量预测树脂固化反应过程,并能为固化过程中反应机理变化的研究提供重要依据;等温法非模型动力学能够更好地预测两种树脂体系在不同恒温条件下的固化反应历程,并且升温法与等温法非模型动力学所得到的反应活化能-固化度之间的变化关系不同,表明不同温度条件下树脂的反应机理不同,这与升温和恒温条件下玻璃化效应及环氧官能团的变化规律相吻合.     

基于松香酸酐的环氧树脂体系固化动力学及TTT图绘制

研制了基于松香酸酐固化剂的生物质环氧树脂体系,采用全动态DSC法研究了树脂体系的固化反应动力学,通过半经验的唯象模型拟合得到了固化反应参数,活化能Ea为59.68 kJ/g,指前因子A0为1.28×1015s-1,反应级数n为2.483,由此建立了体系固化温度/时间/固化度间的关系;采用恒温DSC及DMA方法测试玻璃化转变温度,应用DiBenedetto经验方程拟合得到了玻璃化转变温度与固化度间的关系.应用锥板旋转黏度计测试了树脂体系不同温度下的凝胶时间,通过线性回归分析得到了凝胶时间与温度之间的关系.由唯象模型和DiBenedetto方程分别计算得到凝胶时的固化度为0.386,玻璃化转变温度为26.22°C.由上述工作绘制了基于松香酸酐生物质树脂体系的TTT(time-temperature-transition diagram)固化图,可确定树脂体系在不同温度任意时间下的状态.     

N，N，N’，N’-四炔丙基-4，4＇-二氨基-二苯甲烷与4，4＇-联苯二苄叠氮固化动力学研究

分别利用FtIR和DSC技术对由N，N，N＇，N＇-四炔丙基4,4’-二氨基-二苯甲烷（TPDDM）与4，4’-联苯二苄叠氮（BAMBP）形成的一种新型三唑树脂的固化反应及其动力学进行了研究．TPDDM与BAMBP通过1，3-偶极环加成反应形成三唑五元环结构的聚合物，固化起始温度约为70℃，体系在较低温度下即可固化．反应体系的固化反应是一级反应，采用DSC法与FFIR法分别获得了表观聚合反应动力学参数，其结果具有一定的可比性．     

耐热芴型环氧树脂的非等温固化动力学

合成了9,9’-二[4-(2,3环氧丙氧基)苯基]芴,并以4,4’-二氨基二苯砜胺为固化剂,用非等温DSC法研究了其固化动力学,用Flynn-Wall-Ozawa法和Friedman法确定了固化动力学参数,用动力学模拟推测了固化机理函数,并用TGA法对等温固化树脂的耐热性进行了表征。结果表明:双酚芴环氧固化反应的表观活化能约63.86 kJ/mol,扩散因子为3.80×104s-1,反应级数为1.57;固化反应为枝状成核的自催化反应;等温固化后的环氧树脂于400℃开始分解,700℃时残碳率为41.73%。     

非等温DSC法研究甲壳型液晶PBPCS改性环氧树脂的固化动力学

采用非等温DSC法对聚乙烯基对苯二甲酸二(对丁氧基苯酚)酯(PBPCS)/环氧树脂/甲基四氢苯酐固化体系的固化反应热行为以及固化动力学进行了研究,分别利用Kissinger和Ozawa动力学模型计算得到各体系固化反应的表观活化能,利用Crane模型计算出固化反应级数,得出了适于该树脂体系固化反应过程的动力学方程.结果表明该体系固化反应按照一级反应进行,PBPCS的加入不改变环氧树脂的固化机理,甲壳型液晶高分子PBPCS可以用于环氧树脂的改性研究.通过固化体系的DSC分析确定了体系固化工艺为90℃/2h→120℃/2h→140℃/1.5h,为聚乙烯基对苯二甲酸二(对丁氧基苯酚)酯/环氧树脂/甲基四氢苯酐体系的固化、性能测试和应用提供了理论依据,也为甲壳型液晶高分子改性环氧树脂的研究提供一定理论基础.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.