阻燃玻纤增强尼龙66的制备及性能研究

研究了用环保型阻燃剂溴化聚苯乙烯(PBS)、三氧化二锑(Sb2O3)、玻璃纤维(GF)以及功能助剂通过双螺杆挤出机制备出27%(wt)玻纤含量的高性能环保型阻燃增强尼龙66(PA66)复合材料。DSC和TGA结果表明,玻纤和阻燃剂等填料阻碍PA66结晶过程中分子链段的运动,降低其结晶能力,同时降低了复合材料的热稳定性;SEM结果表明复合材料各组分之间的界面粘结力较强,填料在基体中的分散性较好;力学和阻燃性能测试结果表明,与PA66相比,复合材料的拉伸强度、弯曲强度和弯曲模量分别提高了100%、110%和250%,阻燃性能达到V-0级(0.8 mm)。     

磷杂菲类阻燃剂的合成及其与聚磷酸铵复合膨胀体系对环氧树脂的阻燃性能研究

以9,10-二氢-9-氧杂-10-磷杂菲-10-氧化物(DOPO)、五硫化二磷(P2S5)为原料合成9,10-二氢-9-氧杂-10-磷杂菲-10-硫化物(DOPS),并将DOPS与聚磷酸铵(APP)组成复合阻燃剂,用于环氧树脂(EP)的阻燃改性.通过氧指数(LOI)、垂直燃烧(UL-94)、热失重(TGA)、锥形量热(CONE)和扫描电镜(SEM)等方法对改性后的环氧树脂的阻燃性能和阻燃机理进行了测试和分析.实验结果表明,DOPS/APP阻燃体系对EP具有很好的阻燃性能,且复配阻燃剂的阻燃效果比单一的阻燃剂阻燃效果好;其中,当阻燃剂的总添加量达到30%时即W_(DOPS)=10%、W_(APP)=20%时,阻燃EP复合材料的LOI值可达到29.2%,垂直燃烧等级达到UL-94 V-0级,残炭量可达49.3%.     

石墨烯负载离子液体的制备及其与六苯氧基环三磷腈协效阻燃环氧树脂的性能研究

本文以可膨胀石墨(EG)和1-丁基-3-甲基咪唑六氟磷酸盐离子液体([BMIM]PF_6)为原料,在去离子水中通过绿色、简单的球磨法成功制备出了石墨烯负载离子液体杂化物(GnP@ILs),并对其结构组成进行表征.将GnP@ILs单独或与六苯氧基环三磷腈(HPCTP)混合加入到环氧树脂(EP)中,研究其对EP复合材料综合性能的影响.极限氧指数(LOI)、垂直燃烧(UL-94)和锥形量热测试结果表明,GnP@ILs能提高EP复合材料的阻燃性能,同时与HPCTP复配的EP复合材料(EP/7.2wt%HPCTP/1.8wt%GnP@ILs)的阻燃性能最好,LOI达到33.8%,并通过了UL-94V 0级.EP/7.2wt%HPCTP/1.8wt%GnP@ILs的热释放速率峰值和总热释放量分别降低了55.54%和44.28%.同时,[BMIM]PF_6的加入增强了阻燃剂与EP的界面相容性,EP复合材料的拉伸强度和抗冲强度均明显提高.     

PP/EVA/OMMT纳米复合材料及其阻燃材料的动态燃烧行为

利用锥形量热仪(CONE)在35kW/m2热辐照条件下,并结合极限氧指数(LOI)和UL-94垂直燃烧测试方法对聚丙烯(PP)/乙烯-醋酸乙烯酯共聚物(EVA)/有机蒙脱土(OMMT)纳米复合材料和加入无卤复配阻燃剂制备的PP/EVA/OMMT/氢氧化铝(ATH)/三氧化二锑(AO)纳米复合阻燃材料的热释放速率、烟释放及材料在燃烧时的质量损失行为进行了研究。结果表明,添加5%(质量分数)OMMT可以提高PP/EVA复合材料的阻燃性能,燃烧时的热释放速率、质量损失率以及烟释放量减少,且OMMT与无卤复配阻燃剂之间可产生阻燃协同作用,使纳米复合阻燃材料的阻燃性能、热稳定性和抑烟性进一步增强。     

核壳型纳米粒子填充PP-EVA及阻燃材料的动态燃烧行为

利用锥形量热仪(CONE)和热重分析(TGA),并结合极限氧指数(LOI)和UL-94垂直燃烧测试方法对核(PSt/OMMT)-壳(PBA)结构纳米复合粒子(CSN)填充聚丙烯(PP)-乙烯-醋酸乙烯酯共聚物(EVA)复合材料及加入无卤复配阻燃剂制备的PP-EVA/CSN/聚磷酸铵(APP)/层状氢氧化镁铝(LDH)复合阻燃材料的阻燃性能及热降解行为进行了研究。结果表明,添加10%(wt)CSN可以提高PP-EVA复合材料的阻燃性能,且PP-EVA复合体系燃烧时的热释放速率、有效燃烧热减少,热稳定性增强。CSN与APP/LDH产生阻燃协同作用,使复合阻燃材料的阻燃性能、热稳定性能进一步提高。     

次磷酸铝协同硼酸锌阻燃聚乙烯

以次磷酸铝(AHP)和硼酸锌(ZB)为复合阻燃剂,通过熔融共混法制备了阻燃聚乙烯(PE)材料,研究了AHP和ZB对PE的协同阻燃效应。 结果表明,AHP、ZB阻燃剂在PE基体中分散均匀;添加质量分数为25%AHP阻燃剂,PE材料的极限氧指数值(LOI)提升至25%,通过垂直燃烧测试(UL-94(3.2 mm))V-2级,显示出良好的阻燃效果;引入ZB后,材料LOI值呈先升高后下降趋势,在m(AHP):m(ZB)=21:4时,出现峰值,达到27.2%,并通过UL-94(3.2 mm)V-1级;热失重分析(TGA)结果显示,AHP、ZB阻燃剂能同时提高PE材料的热稳定性和成炭率,当m(AHP):m(ZB)=17:8时,残渣率达到25.7%。     

环三磷腈-DOPO大分子阻燃剂的 合成及阻燃环氧树脂性能

通过取代反应、 缩合反应和加成反应等合成了一种无机-有机杂化大分子阻燃剂 六-[4-(N-苯基氨基-DOPO-次甲基)苯氧基]环三磷腈(DOPO-PCP), 并利用傅里叶变换红外光谱、 ¹H和 ³¹P核磁共振波谱对其进行结构表征. 将DOPO-PCP用于环氧树脂(DGEBA)阻燃, 得到环氧树脂阻燃固化物, 通过极限氧指数(LOI)、 垂直燃烧测试(UL-94)、 热重分析与锥形量热(Cone)测试等对阻燃环氧树脂固化物的热稳定性及燃烧性能进行分析; 利用扫描电子显微镜及Mapping观察并分析了燃烧碳层的形貌与元素分布. 研究结果表明, 产物的结构符合设计的DOPO-PCP分子结构; 当DOPO-PCP在DGEBA中添加量(质量分数)达12.2%时, 磷含量为1.3%, 制得的阻燃环氧树脂固化物垂直燃烧测试通过UL-94 V-0级, LOI值为36.2%; Cone测试结果表明, DOPO-PCP的添加有效降低了DGEBA燃烧时热量与烟气的释放, 且在高温下碳残余量显著增加. 研究表明DOPO-PCP兼具气相和凝固相阻燃机理, 对DGEBA有良好的阻燃性能.     

阻燃PA66/二乙基次磷酸铝复合材料的研究

通过双螺杆挤出机熔融共混制备了阻燃PA66/二乙基次磷酸铝(ADP)复合材料,采用极限氧指数(LOI)、垂直燃烧(UL94)测试、锥形量热仪(Cone)等研究了PA66/ADP材料的燃烧性能,同时还通过拉伸、弯曲强度测试考察了PA66/ADP复合材料的力学性能.研究表明:ADP添加量为8%时,该体系达到了UL94V-0级,LOI值由25. 3%提高到30. 2%. PA66/ADP材料的热释放速率峰值由1 168 k W/m2下降到535 k W/m2,添加ADP能够显著地增强成炭率,增强隔热作用.     

碱式硫酸镁晶须阻燃乙烯-醋酸乙烯酯共聚物的研究

利用极限氧指数、UL-94垂直燃烧试验、锥形量热器、拉伸测试等手段研究了碱式硫酸镁晶须(MOS)填充阻燃乙烯-醋酸乙烯酯共聚物(EVA)的燃烧性能和力学性能,并与氢氧化镁(MH)填充阻燃EVA进行了比较。实验结果表明：MOS是一种性能优良的无卤阻燃剂。当填充量相等时,与EVA／MH相比,EVA／MOS具有更高的极限氧指数和UL-94垂直燃烧级别,更低的热释放速率、有效燃烧热和质量损失速率,以及更高的力学强度。     

OMMT-NC-膨胀型阻燃剂三元协同阻燃LLDPE的效果

采用有机蒙脱土(OMMT)和碳酸镍(NC)为阻燃协效剂,与膨胀型阻燃剂(IFR)三元体系协同阻燃线性低密度聚乙烯(LLDPE).采用热重分析(TGA)、氧指数(LOI)测试、UL-94燃烧测试和锥形量热测试(CONE)研究了LLDPE阻燃体系的热稳定性和燃烧性能;采用红外光谱分析(FT-IR)、数码相机和扫描电子显微镜(SEM)对燃烧残余物的结构和形貌进行了分析.结果表明:固定mnLLDPE/mIFR=7/3,当moMMT/m(LLDPE+IFR)=0.04时,阻燃体系的LOI为31.5％,通过UL-94 V-0级测试,LLDPE-IFR-OMMT的残炭率为15.09％,最大热释放速率(PHRR)相比于纯LLDPE降低了50％;向LLDPE-IFR-OMMT体系中添加NC,少量的NC就能显著增加体系的阻燃性能,当mNC/m(LLDPE+IFR)=0.02时,阻燃体系的LOI为32.7％,LLDPE-IFR-OMMT-NC的残炭率达到19.04％,PHRR相比于纯LLDPE降低了57％.OMMT和NC的加入能催化LLDPE-IFR成炭,形成致密的炭层,增加炭层的强度,从而提高复合材料的阻燃性能.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.