首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 58 毫秒
1.
为提高传统含氟丙烯酸酯乳胶膜表面性能的稳定性,以γ-(甲基丙烯酰氧基)丙基三甲氧基硅烷(MPS)作为可交联单体,采用细乳液聚合法合成了MPS改性的含氟丙烯酸酯共聚物,利用DLS、TEM、IR对聚合物进行表征,研究了MPS对合成乳液的稳定性、涂膜性能和膜表面接触角稳定性的影响。结果表明,细乳液聚合法适合用于对水敏感单体的聚合,合成的纯丙烯酸酯乳胶为球形结构,平均粒径为92 nm,而氟丙乳胶和含3%MPS的含硅氟丙乳胶形成了典型的核壳结构,平均粒径分别增大至107 nm和103 nm,含硅氟丙聚合物中存在Si-O-Si的交联结构。涂膜性能测试表明,MPS的引入增加了共聚物膜的硬度、耐溶剂性和耐水性。接触角测试表明,随MPS用量的增加,乳胶膜对水的初始接触角和动态接触角随时间的降低值均呈先增大后减小的趋势,共聚体系中加入适量MPS,通过含氟链段与MPS链段的协同作用,可显著提高涂膜表面性能的稳定性。  相似文献   

2.
利用表面引发原子转移自由基聚合(SI-ATRP)在聚对苯二甲酸乙二醇酯(PET)薄膜表面接枝苯乙烯和4-氟苯乙烯的共聚物.研究不同反应时间和不同配比下接枝共聚物对聚酯薄膜表面组成、结构和性能的影响.通过傅利叶变换红外光谱仪(ATR/FTIR),X-射线光电子能谱仪(XPS),凝胶渗透色谱(GPC)和扫描电子显微镜(SEM)对接枝改性前后PET薄膜的表面组成,结构和形貌进行分析;利用接触角测试和表面能计算对比研究接枝改性前后PET薄膜的表面性能.结果表明反应时间和单体百分含量对接枝百分率及接触角有一定的影响,随着反应时间的增长,聚酯薄膜表面接枝百分率增大,接触角增加,表面自由能下降.  相似文献   

3.
通过可逆加成-断链链转移(RAFT)溶液聚合,以三硫代碳酸酯为RAFT试剂,偶氮二异丁腈(AIBN)为引发剂,1,4-二氧六环为溶剂,制备甲基丙烯酸(2,2,2-三氟)乙酯(TFEMA)和苯乙烯(St)共聚物.详细研究了不同引发剂的用量、RAFT试剂与引发剂摩尔比以及聚合温度等实验条件对聚合反应过程的影响.通过GPC、FTIR测试共聚物的分子量、分子量分布和分子结构,并用静态接触角仪和AFM分别表征聚合物膜的接触角、表面能及膜的表面形貌.  相似文献   

4.
由五氟苯肼和2-(4-羟基苯甲酰)苯甲酸制备了AB-型双官能团单体4-(4-羟基苯基)-2-五氟苯基-二氮杂萘酮,以苯做带水剂,在K2CO3的催化下温和的反应条件下通过自身亲核缩聚反应合成了结构规整的氟化聚二氮杂萘酮芳醚材料.用傅里叶衰减全反射红外光谱(FTIR ATR)、氢谱(1H-NMR)、氟谱(19F-NMR)对材料的结构进行了表征.该聚合物的玻璃化转变温度Tg为316℃,Td,5 wt%为491℃,具有良好的热性能;该聚合物薄膜样品测试结果表明该材料具有高的力学性能和绝缘性,拉伸强度超过了60 MPa,表面电阻率为1.8×1015Ω/m2,体积电阻率为5.6×1012Ω/m3;该聚合物在DMAc,DMF,DMSO,NMP,1,1,2,2-四氯乙烷,四氢呋喃,氯仿,吡啶和环丁砜中有良好的溶解性,可加工得到光滑、硬韧的膜;利用表面接触角测定仪考察了不同溶剂体系所得膜材料的表面性能,用DMAc制备膜的接触角为93.3°,用氯仿制备膜的接触角为92.5°,用THF制备膜的接触角为127.1°,接触角大于聚四氟乙烯(112°),且所有考察溶剂中所得膜的接触角都大于90°,具有较好的憎水性.  相似文献   

5.
以甲基丙烯酸羟乙酯封端的水性聚氨酯作为大分子单体,与甲基丙烯酸甲酯及甲基丙烯酸全氟烷基乙基酯在乳液中进行自由基共聚合,制备出具有核壳结构的水性含氟聚氨酯-丙烯酸酯乳液。通过激光粒度分析仪、FT-IR、DSC、TGA、接触角、力学等表征手段,对乳液及其乳胶膜的结构和性能进行了研究,还着重探讨了甲基丙烯酸全氟烷基乙基酯的含量对乳胶膜性能的影响,结果表明:所制得的材料具有预期结构,并且具有优异的表面性能和力学性能,氟单体的引入使乳胶膜的表面能大大降低,而力学性能明显提高。  相似文献   

6.
界面聚合法制备聚哌嗪酰胺复合纳滤膜   总被引:2,自引:1,他引:1  
以聚醚砜超滤膜为基膜,哌嗪(PIP)为水相单体,均苯三甲酰氯(TMC)为有机相单体,采用界面聚合法制备了复合纳滤膜,扫描电镜、表层的红外分析结果表明在基膜表面聚合了一层聚酰胺膜,膜性能测定结果表明膜表面荷负电,对不同无机盐的截留率为Na2SO4MgSO4MgCl2NaCl。界面聚合条件对膜性能的影响表明,最佳聚合条件为:PIP浓度0.5%~2%,TMC浓度0.15wt%~0.75wt%,聚合时间≥1min,热处理温度60℃~80℃,时间15 min左右。  相似文献   

7.
由六氟环氧丙烷二聚体、三聚体分别与4-环己烯-1,2-二甲醇反应合成了2种新型的双全氟烷氧基取代的环氧环己烷衍生物(EFPO1和EFPO2),其结构经FT-IR和1H NMR确证。 与常见全氟烷基型功能单体不同,此类含氟环氧化合物与环氧树脂预聚物具有良好的相容性并且可改善其疏水性能。 初步考察了上述单体对环氧树脂紫外光固化涂料的改性作用,结果表明,随涂料中含氟单体用量的增加,固化膜的初始水接触角线性增大;其中,EFPO2因其含较长的全氟烷氧基团而具有比EFPO1更好的疏水效果。 如加入1%EFPO2时,固化膜接触角为99°,比未添加含氟单体的固化膜大14°,而相同含量EFPO1固化膜接触角为87°。 当EFPO2含量为5%时,固化膜的疏水性能进一步提高,接触角为113°。 此外,固化膜经加热处理(110 ℃,6 h)后疏水性能明显增强,如EFPO2含量为1%~5%时,固化膜经热处理后,接触角由99°~113°提高至113°~118°,EFPO1固化膜经热处理后接触角也由87°~100°提高至99°~110°。 固化膜疏水性能的提高可能是由于经过加热处理,含氟链段向表面迁移。 由此可见,这类含氟单体可作为表面改性剂应用于涂料、油墨和离型材料。  相似文献   

8.
含氟丙烯酸酯共聚物防粘剂的制备及其表面性能研究   总被引:2,自引:0,他引:2  
以甲基异丁基甲酮为溶剂,偶氮二异丁腈为引发剂,全氟烷基乙基丙烯酸酯、丙烯酸十八酯、丙烯酸丁酯和甲基丙烯酸羟乙酯为原料,溶液聚合制得了均一的含氟丙烯酸酯共聚物防粘剂,并研究了其表面性能。结果表明:全氟烷基乙基丙烯酸酯单体的加入显著降低了共聚物的表面能,提高了共聚物膜的硬度、耐水、耐碱、耐溶剂等性能。当加入ω(氟单体)为30%时,表面能降低至14.7 mN/m,低于有机硅类防粘剂的表面能,含氟丙烯酸酯共聚物膜与压敏胶的的剥离力较低,剩余粘附率为93.2%,该共聚物膜的防粘等综合性能最好。  相似文献   

9.
使用四乙基氢氧化铵(TEAH)液相本体改性聚偏氟乙烯(PVDF), 以过氧化苯甲酰(BPO)为引发剂, 将丙烯酸(AA)接枝到改性PVDF骨架上, 合成了聚偏氟乙烯接枝聚丙烯酸(PVDF-g-PAA)共聚物, 通过浸没沉淀法制备了PVDF-g-PAA亲水性油水分离膜. 通过傅里叶变换红外光谱(FTIR)、 扫描电子显微镜(SEM)和过滤试验分析了膜的结构和分离性能. 研究了不同接枝条件对PVDF-g-PAA膜接枝率的影响. 同时, 通过膜接枝率与膜表面接触角的关系确定最佳接枝条件. 结果表明, TEAH使PVDF脱去HF产生碳碳双键且PAA接枝到改性的PVDF骨架上, 膜内外孔隙分布均匀; PVDF-g-PAA膜的接触角随着接枝率的提高而降低. 接枝单体AA含量为45%, 接枝温度为85 ℃, 接枝4 h制备的PVDF-g-PAA膜的接枝率为20.1%, 孔隙度为65.3%, 平均孔径为78.0 nm, 接触角为57.5°, 且在60 s内接触角降至14.3°; 纯水通量提高到571.33 L/(m2·h), 截留率和水通量恢复率分别达到94.3%和88.7%, 且通量衰减率仅为9.8%. 与纯PVDF膜相比, PVDF-g-PAA膜的分离性能显著提高.  相似文献   

10.
含氟丙烯酸酯-苯乙烯共聚物的制备及其表面性能的研究   总被引:4,自引:0,他引:4  
研究了聚合工艺、含氟丙烯酸酯类单体种类和用量、苯乙烯和自由基引发剂用量及硅烷偶联剂、催化剂等因素对含氟丙烯酸酯-乙烯共聚物表面性能的影响。结果表明:聚合工艺、含氟丙烯酸酯类单体种类和用量对共聚物表面的憎水性能有显著的影响;采用延时滴加含氟丙烯酸酯类单体可提高共聚物膜表面的憎水性;随含氟丙烯酸酯类单体侧链含氟烷基的链长和氟原子数及含氟单体用量的增加,共聚物水接触角增大,吸水率下降;共聚物薄膜的硬度则与含氟丙烯酸酯类单体中α-取代基、侧链含氟烷基的链长和用量、苯乙烯用量、引发剂浓度等相关;硅烷偶联剂和催化交联剂的加入可提高共聚物薄膜的强度。  相似文献   

11.
用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.  相似文献   

12.
Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.  相似文献   

13.
In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.  相似文献   

14.
The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.  相似文献   

15.
The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.  相似文献   

16.
KMnO4-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.  相似文献   

17.
The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.  相似文献   

18.
A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.  相似文献   

19.
Zhanhui Yang  Shiyi Yang  Jiaxi Xu 《Tetrahedron》2017,73(23):3240-3248
Regiospecific and direct imidation of the methyl C(sp3)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.  相似文献   

20.
A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号