氮气等离子体改性壳聚糖-聚丙烯腈复合纳滤膜

以氮气低温等离子体对壳聚糖-聚丙烯腈复合纳滤膜进行表面改性。用接触角、扫描电镜和扫描探针显微镜观察膜表面的亲水性和形貌特征,X射线光电子能谱分析膜表面化学组成,以γ-氨基丁酸为分离对象表征膜的纳滤性能。结果表明:经50W、20Pa的氮气等离子体作用2min,壳聚糖膜表面获得最大程度的亲水性改善,其接触角由102.0°下降至44.3°,平整度明显提升;膜表面C—C、C—O和酰胺基团均有减少,而胺基和羰基相应增加;在pH=6.15的水溶液中对w=1.0%的γ-氨基丁酸进行纳滤,液体的通量由原来的1.12L/(m2·h)提高至1.75L/(m2·h),且对氨基酸的截留率从28%提升至83%。     

壳聚糖-聚丙烯腈复合纳滤膜的氨气等离子改性

利用氨气低温等离子体对壳聚糖聚丙烯腈复合膜进行表面改性,制成了在低压、弱酸条件下,带正电荷的壳聚糖一聚丙烯腈复合纳滤膜。探讨了等离子处理时间、放电功率对膜亲水性改善效果的影响,采用单因素实验确定了最佳等离子体处理条件。通过扫描探针显微镜、接触角测试、表面光电子能谱检测等手段对膜表面进行了表征。经过等离体改性后,复合膜的亲水性及纳滤性能均大幅提高。改性后,在0．05MPa、pH≈6．7条件下,壳聚糖一聚丙烯腈复合膜对0．1mol／L的）,一氨基丁酸溶液的通量为3．19L／（m^2·h）,截留率为78％。     

丙烯醇等离子体处理聚四氟乙烯的表面结构与润湿性

聚四氟乙烯经丙烯醇等离子体处理后,在其表面形成了一层亲水性的聚合物薄膜。水在表面的接触角为40—60°不等,由等离子体处理时间决定。对表面的全反射红外光谱、ESCA分析和SEM观测发现,等离子体处理后在原表面上形成的聚合物膜包含—CH_3、—CH_2、C=O和C—OH等基团,并且表面光滑、平整。     

超支化聚合物PAMAM表面改性PAN超滤膜

首先通过碱处理将聚丙烯腈(PAN)超滤膜表面的氰基转变为羧基,然后使其在聚酰胺-胺(PAMAM)水溶液中与PAMAM进行表面改性反应,制得PAN-PAMAM膜。采用傅里叶红外光谱(FT-IR)、X光电子能谱(XPS)、扫描电镜(SEM)和原子力显微镜(AFM)等手段对PANPAMAM膜的结构进行表征。结果表明:通过表面改性反应,PAMAM结合在PAN超滤膜表面,形成一层致密、光滑的亲水性表层;PAN-PAMAM膜的接触角比纯PAN超滤膜降低了20°左右;PAN-PAMAM膜的纯水通量为14.9L/(m~2·h),对聚乙二醇(PEG2000)的截留率达到91.4%。     

抗污染PVA/PVDF电纺纳米纤维复合超滤膜的制备及过滤性能

以聚对苯二甲酸二醇酯(PET)无纺布为基底,聚偏氟乙烯(PVDF)纳米纤维为支撑层,聚乙烯醇(PVA)纳米纤维膜为分离层,采用静电纺丝法制备超滤膜,并用水/丙酮混合溶液对复合纳米纤维膜表面进行溶液处理,再加入戊二醛交联改性得到致密分离层.采用扫描电子显微镜(SEM)和红外光谱(FTIR)表征了复合超滤膜的表面,用水接触角(WCA)表征复合超滤膜的亲水性.在0.02 MPa恒压下死端过滤油/水乳液,测试复合超滤膜的过滤性能.结果表明,最优条件下制备的复合超滤膜死端过滤油/水乳液的通量为(42.50±4.78)L/(m~2·h),截留率达到(95.72±0.33)%;循环使用5次后,依然具有较好的过滤性能,常压下死端过滤复合超滤膜的纯水通量为(3469±28)L/(m~2·h).     

超支化聚酯低压纳滤膜的制备与表征

通过超支化聚酯(HPE)末端的羟基与戊二醛(GA)之间的羟醛缩合反应,采用简单的浸涂-交联方法,制备了一种以聚砜超滤膜为支撑层,交联的HPE为活性分离层的复合纳滤膜.采用衰减全反射红外光谱(ATR-FTIR)、接触角测定、扫描电子显微镜(SEM)对纳滤膜的表面化学组成、亲水性和膜形貌进行了表征.考察了HPE溶液浓度、GA溶液浓度对膜分离和渗透性能的影响,优化的HPE和GA溶液浓度分别为9.8 g/L和7.4 g/L,此时在0.4 MPa下膜的水通量达69.6 L/(m2.h),对Na2SO4脱除率为93.2%,表现出低操作压力、高通量、高脱盐率的优异性能.纳滤膜对无机盐的截留顺序为Na2SO4>NaCl>MgSO4>MgCl2,呈现明显的荷负电特征.     

接枝丙烯酰胺改善聚乙烯膜表面亲水性的研究

利用等离子体技术和紫外照射接枝相结合在聚乙烯膜表面接枝丙烯酰胺(AAm)以改善其亲水性。通过衰减全反射红外光谱(ATR-FTIR)、X射线光电子能谱(XPS)和接触角测定验证了在无光引发剂的条件下,将等离子体预处理和紫外照射接枝结合起来可以有效地提高AAm的接枝效果,很好地改善PE膜表面的亲水性。探讨了等离子体复合参数W/(FM)、等离子体预处理时间、AAm单体浓度以及紫外照射时间对改善PE膜表面亲水性的影响,确定改善PE膜表面亲水性的最佳实验条件。     

碳纳米管对聚偏氟乙烯膜的共混改性研究

用相转化法制备了聚偏氟乙烯/碳纳米管共混膜,研究了共混膜的表面结构、水通量、孔隙率、接触角和机械性能。结果显示碳纳米管的加入提高了聚偏氟乙烯膜的亲水性和水通量,当聚偏氟乙烯浓度为10wt.%,碳纳米管含量为1.5wt.%时,共混膜的水通量和孔隙率最高,从243 L/m2·h和86.2%提高到365 L/m2·h和91.4%;接触角也由82°减小为67°;同时,共混膜的机械性能也得到显著提高。     

聚多巴胺/聚乙烯亚胺共沉积中间层增强薄膜复合正渗透膜性能

以聚多巴胺/聚乙烯亚胺(PDA/PEI)共沉积于三醋酸纤维素(CTA)多孔支撑膜表面形成中间层,再结合界面聚合法获得聚酰胺薄膜,构建了PDA/PEI共沉积中间层改性薄膜复合(TFC)正渗透(FO)膜.通过傅里叶变换衰减全反射红外光谱法、扫描电子显微镜、原子力显微镜、溶质截留法、水接触角仪等研究了PDA/PEI共沉积中间层对CTA膜和TFC膜的表面结构和性质的影响.研究结果表明,PDA/PEI共沉积使得CTA膜表面变得更为平滑,表面孔径减小至(30.0±4.1) nm,且表面孔径分布趋于均一.同时,在PDA/PEI共沉积改性CTA膜表面界面聚合得到的聚酰胺层呈现出更均匀的叶片状结构和优异的亲水性.基于此,具有PDA/PEI共沉积中间层的TFC正渗透膜显著提高了水通量(FO模式:(7.1±2.3) L/(m^2·h)),较空白TFC膜提升了57.6%.同时,中间层改性TFC膜具有更低的反向盐通量(FO模式:1.4±0.1 g/(m^2·h))和"净盐通量"(FO模式:(0.2±0.06) g/L),与空白TFC膜相比分别下降了83.9%和90.6%.说明PDA/PEI共沉积中间层不仅能有效提升TFC正渗透膜的水渗透性,而且大幅提升了膜的截盐性和渗透选择性.     

四乙基氢氧化铵改性聚偏氟乙烯接枝聚丙烯酸油水分离膜的制备

使用四乙基氢氧化铵(TEAH)液相本体改性聚偏氟乙烯(PVDF), 以过氧化苯甲酰(BPO)为引发剂, 将丙烯酸(AA)接枝到改性PVDF骨架上, 合成了聚偏氟乙烯接枝聚丙烯酸(PVDF-g-PAA)共聚物, 通过浸没沉淀法制备了PVDF-g-PAA亲水性油水分离膜. 通过傅里叶变换红外光谱(FTIR)、 扫描电子显微镜(SEM)和过滤试验分析了膜的结构和分离性能. 研究了不同接枝条件对PVDF-g-PAA膜接枝率的影响. 同时, 通过膜接枝率与膜表面接触角的关系确定最佳接枝条件. 结果表明, TEAH使PVDF脱去HF产生碳碳双键且PAA接枝到改性的PVDF骨架上, 膜内外孔隙分布均匀; PVDF-g-PAA膜的接触角随着接枝率的提高而降低. 接枝单体AA含量为45%, 接枝温度为85 ℃, 接枝4 h制备的PVDF-g-PAA膜的接枝率为20.1%, 孔隙度为65.3%, 平均孔径为78.0 nm, 接触角为57.5°, 且在60 s内接触角降至14.3°; 纯水通量提高到571.33 L/(m²·h), 截留率和水通量恢复率分别达到94.3%和88.7%, 且通量衰减率仅为9.8%. 与纯PVDF膜相比, PVDF-g-PAA膜的分离性能显著提高.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.