Ce-promoted Mn/Na2WO4/SiO2 catalyst for oxidative coupling of methane at atmospheric pressure

A series of Ce-promoted Mn-Na2WO4/SiO2 catalysts were prepared by incipient wetness impregnation method, and their catalytic performance for oxidative coupling of methane (OCM) was investigated at atmospheric pressure in a micro-quartz-tube reactor. The catalysts were characterized by X-ray diffraction (XRD), temperature program reduction (TPR) and BET surface area. Ce promoter increased surface area and Na2WO4 species dispersion, which enriched the amount of the surface species. In addition, Ce promoter in...     

Characterization and catalytic behavior of Na-W-Mn-Zr-S-P/SiO2 prepared by different methods in oxidative coupling of methane

Na-W-Mn-Zr-S-P/SiO2 catalysts for oxidative coupling of methane (OCM) were prepared by incipient wetness impregnation, sol-gel and mixture slurry methods. The catalyst prepared by mixture slurry method showed the best catalytic performance among all samples. In addition, the effects of different addition sequences of Na, W, Mn, Zr, S and P on the catalytic performance were studied. The absence of Na before the addition of Mn and Zr in the catalysts preparation depressed the formation of the active phases of Mn2O3 and ZrO2 and decreased the activities of the catalysts significantly.     

Effects of operating parameters on oxidative coupling of methane over Na-W-Mn/SiO2 catalyst at elevated pressures

The effects of operating parameters on oxidative coupling of methane (OCM) over Na-W-Mn/SiO2 catalyst have been studied at elevated pressures of 0.2, 0.3 and 0.4 MPa under low gaseous hourly space velocity (GHSV) and low temperature conditions. Experimental results show that when the operating pressure is increased, C2+ yield slightly decreases, while the maximum ratio of ethylene to ethane remains unchanged. Moreover, it has been found empirically that increase of pressure does not affect the catalyst behavior permanently, the catalyst recovers its original low pressure performance without hysteresis behavior by reducing the pressure. Under the investigated conditions, when oxygen is completely consumed, the increase of GHSV leads to improvement in C2 selectivity, while C3+ and COx selectivities decrease slightly. The C2+ selectivity increases by increase of nitrogen diluent in the feed, but the C3+ hydrocarbons selectivities decrease with increase of nitrogen since it is possible that further dilution at high pressure may reduce the probability of collision between CH3 and C2+ hydrocarbons. During the stability test at high pressure, the catalyst performance remains unchanged throughout the 20 h running. The fresh and used catalysts were characterized using XRD, SEM and N2 adsorption-desorption methods. It was found that the phase transformation of the support from α-cristobalite to tridymite and quartz does not have obvious effect on catalyst performance at high pressure.     

LiCl对Fe_2O_3/SiO_2甲烷氧化偶联反应的助催化作用

使用穆斯堡尔谱，ESR和XRD等技术表征了未添加助剂和添加LiCl的Fe2O3／SiO2催化剂．XRD结果指出，添加LiCl的Fe2O／SiO2催化剂出现铁酸盐和α-方石英的衍射峰，这种结果的出现与该催化剂有较高的C2烃选择性密切相关。穆斯堡尔谱结果表明：添加LiCl的Fe2O3／SiO2催化剂有更高的结构对称性．这种结构对分子氧的活化起着重要的作用．氯的存在大大降低了氧的离解吸附的速率，减少了原子氧的吸附位的数目，并可除去吸附的原子氧，该氧种对COx的生成有利．     

Kinetic studies of the oxidative coupling of methane over the Mn/Na2WO4/SiO2 catalyst

Oxidative coupling of methane is a direct way to obtain C2 hydrocarbon,and Mn-Na-W/SiO2 catalyst is the most promising among all the catalysts.The 2%Mn/5%Na2WO4/SiO2 catalyst was prepared by the incipient wetness impregnation method.A 7-step heterogeneous reaction model of the oxidative coupling of methane to C2 hydrocarbons was conducted by co-feeding methane and oxygen at a total pressure of 1 bar over the catalyst.The kinetic measurements were carried out in a micro-catalytic fixed bed reactor.The kinetic data were obtained at the appropriate range of reaction conditions (4 kPa＜Po2 ＜20 kPa,20 kPa＜PCZH4 ＜80 kPa,800℃＜T＜900℃).The proposed reaction kinetic scheme consists of three primary and four consecutive reaction steps.The conversions of hydrocarbons and carbon oxides were evaluated by applying Langrnuir-Hinshelwood type rate equations.Power-law rate equation was applied only for the water-gas shift reaction.In addition,the effects of operating conditions on the reaction rate were studied.The proposed kinetic model can predict the conversion of methane and oxygen as well as the yield of C2 hydrocarbons and carbon oxides with an average accuracy of ±15%.     

Scale up and stability test for oxidative coupling of methane over Na2WO4-Mn/SiO2 catalyst in a 200 ml fixed-bed reactor

The study of scale up for the oxidative coupling of methane （OCM） has been carried out in a 200 ml stainless steel fixed-bed reactor over a 5wt% Na2WO4-1.9wt% Mn/SiO2 （W-Mn/SiO2） catalyst. The effects of reaction conditions were investigated in detail. The results showed that, with increasing reaction temperature, the gas-phase reaction was enhanced and a significant amount of methane was converted into COx; with the CH4/O2 molar ratio of 5, the highest C2 （ethylene and ethane） yield of 25% was achieved; the presence of steam （as diluent） had a positive effect on the C2 selectivity and yield. Under lower methane gaseous hourly space velocity （GHSV）, higher selectivity and yield of C2 were obtained as the result of the decrease of released heat energy. In 100 h reaction time, the C2 selectivity of 66%-61% and C2 yield of 24.2%-25.4% were achieved by a single pass without any significant loss in catalytic performance.     

La2Zr2O7催化剂结构相变对甲烷氧化偶联反应性能的影响

采用共沉淀法并通过改变焙烧温度制备了一系列具有不同晶相结构的La₂Zr₂O₇催化剂，在微型固定床反应器上评价其甲烷氧化偶联反应性能，并利用XRD、Raman、CO₂-TPD、XPS等表征手段，探究催化剂的物相结构、表面碱性以及表面氧物种的变化规律。结果表明，随着焙烧温度从700℃逐渐升高到1200℃，La₂Zr₂O₇催化剂结晶度不断提高，晶相发生明显变化，从无定形结构逐渐向缺陷萤石结构过渡，最终转变成烧绿石结构。焙烧温度提高促使La₂Zr₂O₇晶相转变过程中，催化剂表面的碱性强度减弱，中等碱性位数量以及具有催化活性的表面氧物种O₂^2-和O₂^-的相对含量不断减少，致使催化剂的CH₄转化率和C₂₊选择性不断降低。其中，无定形LZO-CP-700催化剂表现出最佳的甲烷氧化偶联反应性能。     

甲烷氧化偶联W-Mn/SiO2催化剂上O2-脉冲频率效应(PFE)的研究

采用频率脉冲反应方法,以Mn-Na2WO4/S iO2催化剂上甲烷氧化偶联为探针反应,通过实时、原位的四极质谱检测手段,研究氧物种对甲烷C-H键选择性活化的微观历程.首次发现了Mn-Na2WO4/S iO2催化剂上O2-脉冲频率效应,即脉冲反应产物量随氧脉冲注入频率的增加而增加.研究结果表明,在反应条件下,Mn-Na2WO4/S iO2催化剂上有两种活化甲烷的氧物种同时存在,它们活化甲烷的方式不同。     

Experimental investigation of fluidized-bed reactor performance for oxidative coupling of methane

Performance of the oxidative coupling of methane in fluidized-bed reactor was experimentally investigated using Mn-Na2WO4/SiO2,La2O3/CaO and La2O3-SrO/CaO catalysts.These catalysts were found to be stable,especially Mn-Na2WO4/SiO2 catalyst.The effect of sodium content of this catalyst was analyzed and the challenge of catalyst agglomeration was addressed using proper catalyst composition of 2%Mn2.2%Na2WO4/SiO2.For other two catalysts,the effect of Lanthanum-Strontium content was analyzed and 10%La2O 3-20%SrO/CaO catalyst was found to provide higher ethylene yield than La2O3/CaO catalyst.Furthermore,the effect of operating parameters such as temperature and methane to oxygen ratio were also reviewed.The highest ethylene and ethane (C2) yield was achieved with the lowest methane to oxygen ratio around 2.40.5% selectivity to ethylene and ethane and 41% methane conversion were achieved over La2O3-SrO/CaO catalyst while over Mn-Na2WO4 /SiO2 catalyst,40% and 48% were recorded,respectively.Moreover,the consecutive effects of nitrogen dilution,ethylene to ethane production ratio and other performance indicators on the down-stream process units were qualitatively discussed and Mn-Na2WO4/SiO2 catalyst showed a better performance in the reactor and process scale analysis.     

Kinetic study of oxidative coupling of methane over Mn and/or W promoted Na_2SO_4/SiO_2 catalysts

A comprehensive kinetic model for oxidative coupling of methane(OCM)over Mn and/or W promoted Na2SO4/SiO2 catalysts was developed based on a micro-catalytic reactor data.The methane conversion and ethylene,ethane,carbon monoxide and carbon dioxide selectivities were obtained in a wide operating condition range of 750 - 825-C,CH4/O2=2.5 - 10 and contact time=267 - 472 kg s m-3.Reaction networks of six models with different rate equation types were compared together.The kinetic rate parameters of each reaction network were estimated using linear regression or genetic algorithm optimization method(GA).A reaction network suggested by Stansch et al.for OCM was found to be the best one and was further used in this work.The suggested model could predict the experimental results of OCM reaction within a deviation range of ± 20%.     

Oxidative coupling of methane over BaCl2-TiO2-SnO2 catalyst

The performance of BaCl2-TiO2-SnO2 composite catalysts in oxidative coupling of methane reaction has been investigated. A series of BaCl2-TiO2, BaCl2-SnO2, TiO2-SnO2, and BaCl2-TiO2-SnO2 catalysts were prepared, and characterized by BET, XRD, XPS, CO2-TPD and H2-TPR, respectively. The synergistic effect among BaCl2, SnO2 and TiO2 compositions enhances the catalytic performance. The best C2 selectivity and ethylene yield are obtained on the catalyst with the equal molar amount of the three compositions (BaCl2 : TiO2 : SnO2 molar ratio of 1 : 1 : 1). The optimal reaction conditions are as follows: 800°C, 44 mL·min-1 for methane, 22 mL·min-1 for oxygen and a space velocity of 5000 mL·h-1 g-1, and the C2H4 yield over the catalyst is 20.1% with the CH4 conversion of 43.8% and C2 selectivity of 53.3%.     

Rule of 100:An inherent limitation or performance measure in oxidative coupling of methane?

The oxidative coupling of methane over La 2 O 3 /CaO type-catalyst in a fixed-bed reactor is studied under a wide range of operating conditions(973相似文献   

甲烷氧化偶联制烯烃的热力学平衡限度

选择适宜的热力学模型对甲烷氧化偶联制烯烃体系的热力学平衡进行分析,考察温度﹑压力﹑进料组成对体系组分的平衡限度影响。研究发现,在甲烷氧化偶联制烯烃体系中,H2、CO的生成相对容易,C2产物（C2H4、C2H6）不容易生成。通过计算,得到了该体系有利于烯烃生成的反应条件,500℃～800℃、1.5MPa、烷氧摩尔比为7。实验为甲烷氧化偶联反应器和催化剂的开发研究提供热力学依据。     

LiMn_2O_4/TiO_2催化剂上甲烷氧化偶联反应性能的研究

采用固相反应法制备了具有尖晶石结构的LiMn_2O_4/TiO_2系列催化剂,探讨了TiO_2、Li/TiO_2、Mn/TiO_2、LiMn_2O_4及LiMn_2O_4/TiO_2等不同组成催化剂的甲烷氧化偶联反应性能,采用XRD、XPS、CO_2-TPD和H_2-TPR等表征方法对该系列催化剂进行了分析。结果表明,具有尖晶石结构的LiMn_2O_4化合物具有较高的甲烷氧化偶联催化活性,在775℃、0.1MPa、7200mL/(h·g),CH_4∶O_2(体积比)为2.5的条件下,甲烷转化率可达25.8%,C2选择性可达43.2%。TiO_2的存在不仅进一步提高了甲烷转化率和C2选择性,还有效抑制了甲烷完全氧化形成CO_2的过程。负载8%LiMn_2O_4的LiMn_2O_4/TiO_2催化剂性能达到最优,此时甲烷转化率达到31.6%,C2选择性为52.4%,CO_2选择性降低到26.3%。考察了不同焙烧温度对催化剂活性的影响,850℃为LiMn_2O_4/TiO_2催化剂的最佳焙烧温度。     

Influence of alkali metal doping on surface properties and catalytic activity/selectivity of CaO catalysts in oxidative coupling of methane

Surface properties （viz. surface area, basicity/base strength distribution, and crystal phases） of alkali metal doped CaO （alkali metal/Ca= 0.1 and 0.4） catalysts and their catalytic activity/selectivity in oxidative coupling of methane （OCM） to higher hydrocarbons at different reaction conditions （viz. temperature, 700 and 750 ℃; CH4/O2 ratio, 4.0 and 8.0 and space velocity, 5140-20550 cm^3 ·g^-1·h^-1） have been investigated. The influence of catalyst calcination temperature on the activity/selectivity has also been investigated. The surface properties （viz. surface area, basicity/base strength distribution） and catalytic activity/selectivity of the alkali metal doped CaO catalysts are strongly influenced by the alkali metal promoter and its concentration in the alkali metal doped CaO catalysts. An addition of alkali metal promoter to CaO results in a large decrease in the surface area but a large increase in the surface basicity （strong basic sites） and the C2＋ selectivity and yield of the catalysts in the OCM process. The activity and selectivity are strongly influenced by the catalyst calcination temperature. No direct relationship between surface basicity and catalytic activity/selectivity has been observed. Among the alkali metal doped CaO catalysts, Na-CaO （Na/Ca = 0.1, before calcination） catalyst （calcined at 750 ℃）, showed best performance （C2＋ selectivity of 68.8% with 24.7% methane conversion）, whereas the poorest performance was shown by the Rb-CaO catalyst in the OCM process.     

Effect of lithium addition on the performance of proton-conducting catalysts for oxidative coupling of methane under microwave irradiation

The oxidative coupling of methane over lithium modified proton-conducting catalysts irradiated by microwaves has been studied. Compared with protonconducting catalysts, lithium addition to proton-conducting catalysts resulted in changes in product species and product selectivities, favoring the production of C₂ compounds.     

Suppressed formation of CO2 and H2O in the oxidative coupling of methane over La2O3/MgO catalyst by surface modification

Oxidative coupling of methane (OCM) is a promising way to convert methane into C_2 hydrocarbons. However, CO_2 and H_2O are by-products of the reaction. To utilize the higher activity of lanthanum oxide and save its usage, MgO supported La_2O_3 catalyst was prepared. Surface modification of the catalyst with nitric acid was made to suppress the formation of the by-products. Experimental results indicated that the addition of nitric acid increased the surface oxygen species with binding energy of ca. 531.7 eV and at the same time reduced the pore volume of the catalyst. These effects of nitric acid finally led to the increase of C_2 selectivity and the decrease of the by-products formation. Hydrogen selectivity was found about 14%- 18% over the catalysts adopted in this work.     

Reaction Chemistry of W—Mn／SiO2 Catalyst for the Oxidative Coupling of Methane

Reaction chemistry of the OCM reaction on W-Mn/SiO2 catalyst has been reviewed in this account.Initial activity and selectivity,stability in a long-term reaction,reaction at elevated pressures and a modelling test in a stainless-steel fluidized-bed reactor show that W-Mn/SiO2 has promising performance for the development of an OCM process that directly produces ethylene from natural gas.A study on surface catalytic reaction kinetics and used cataly st structure characterization revealed a possible reason why C2 and COx selectivity changed during the long-term reaction.Further improvement of the catalyst composition and preparation metbod should be a future direction of study on OCM reaction over W-Mn/SiO2 catalyst.     

甲烷氧化偶联W-Mn／SiO2催化剂上02-脉冲频率效应（PFE）的研究

采用频率脉冲反应方法，以Mn-Na2WO4／SiO2催化剂上甲烷氧化偶联为探针反应，通过实时、原位的四极质谱检测手段，研究氧物种对甲烷C-H键选择性活化的微观历程．首次发现了Mn-Na2 WO4／SiO2催化剂上O2-脉冲频率效应，即脉冲反应产物量随氧脉冲注入频率的增加而增加．研究结果表明。在反应条件下，Mn-Na2 WO4／SiO2催化剂上有两种活化甲烷的氧物种同时存在，它们活化甲烷的方式不同。