Hydroxyapatite/titania composite bioactivity coating processed by sol-gel method

Hydroxyapatite/titania composite material was coated onto a titanium (pure Ti) substrate by sol-gel method. The hydroxyapatite (HA) and titania (TiO₂) sol were made from precursor and mixed together. The insertion of TiO₂ enhanced the chemical affinity and the physical consistency between HA and Ti substrate. The HA/TiO₂ composite coating adhered tightly to the Ti substrate. Owing to the insertion of TiO₂, the crystallinity of HA has been delayed. The specimens with HA/TiO₂ composite coatings were soaked into SBF, and displayed good bone-like apatite forming ability. The bioactivity of the composite HA coatings were tested in vitro by cell culture.     

Characterization and corrosion studies of titania-coated NiTi prepared by sol-gel technique and steam crystallization

Nickel titanium (NiTi) was dip-coated with titania via the sol-gel route using titanium butoxide (Ti(OC₄H₉)₄) as precursor. The as-coated titania film was crystallized to form anatase by treatment in steam at 105 °C. The crystallized film was relatively thick (about 750 nm) and even. Atomic force microscopy (AFM) revealed that the film was dense with a surface roughness of about 3 nm, and was composed of particles of about 100 nm. X-ray diffractometry (XRD) showed that these particles were composed of nanocrystallites of a few nanometers. Nanoindentation tests of the titania film indicated that the film was tough, possibly due to the nano-size of the crystallites. The mean hardness H and elastic modulus E of the coating were about 1.5 and 70 GPa, respectively. Direct pull-off test recorded a mean coating-substrate bonding strength larger than 17 MPa. Electrochemical impedance spectroscopic (EIS) study and cyclic polarization tests showed that the corrosion resistance of the coated NiTi samples in Hanks’ solution was increased by about two orders of magnitude compared with the substrate. Taken together, the present study showed that steam crystallization is a feasible low-temperature treatment method for sol-gel derived titania coating on NiTi in biomedical applications.     

Preparation of TiO2 thin films from autoclaved sol containing needle-like anatase crystals

A new inorganic sol-gel method was introduced in this paper to prepare TiO₂ thin films. The autoclaved sol with needle-like anatase crystals was synthesized using titanyl sulfate (TiOSO₄) and peroxide (H₂O₂) as starting materials. The transparent anatase TiO₂ thin films were prepared on glass slides from the autoclaved sol by sol-gel dip-coating method. A wide range of techniques such as Fourier transform infrared transmission spectra (FT-IR), X-ray diffraction (XRD), thermogravimetry-differential thermal analysis (TG-DTA), scanning electron microscopes, X-ray photoelectron spectroscopy (XPS) and ultraviolet-visible spectrum were applied to characterize the autoclaved sol and TiO₂ thin films. The results indicate that the autoclaved sol is flavescent, semitransparent and stable at room temperature. The anatase crystals of TiO₂ films connect together to form net-like structure after calcined and the films become uniform with increasing heating temperature. The surface of the TiO₂ films contain not only Ti and O elements, but also a small amount of N and Na elements diffused from substrates during heat treatment. The TiO₂ films are transparent and their maximal light transmittances exceed 80% under visible light region.     

Synthesis, characterization and effect of calcination temperature on phase transformation and photocatalytic activity of Cu,S-codoped TiO2 nanoparticles

A novel copper and sulfur codoped TiO₂ photocatalyst was synthesized by modified sol-gel method using titanium(IV) isopropoxide, CuCl₂·2H₂O and thiourea as precursors. The samples were characterized by X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), scanning electron microscopy equipped with energy dispersive X-ray micro-analysis (SEM-EDX), transmission electron microscopy (TEM) and Fourier transform infrared (FT-IR) analysis. The XRD results showed undoped and Cu,S-codoped TiO₂ nanoparticles only include anatase phase. Effect of calcination temperature showed rutile phase appears in 650 and 700 °C for undoped and 0.1% Cu,S-codoped TiO₂, respectively. The SEM analysis revealed the doping of Cu and S does not leave any change in morphology of the catalyst surface. The increase of copper doping enhanced “red-shift” in the UV-vis absorption spectra. The TEM images confirmed the dopants suppressed the growth of TiO₂ grains. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. The results showed photocatalytic activity of the catalysts with 0.05% Cu,0.05% S and 0.1% Cu,0.05% S were higher than that of other catalysts under ultraviolet (UV) and visible irradiation, respectively. Because of synergetic effect of S and Cu, the Cu,S-codoped TiO₂ catalyst has higher activity than undoped and Cu or S doped TiO₂ catalysts.     

Structural, photochemical and photocatalytic properties of zirconium oxide doped TiO2 nanocrystallites

Composite photocatalysts composed of TiO₂ and ZrO₂ have been prepared via the sol-gel method. The as-prepared nanocomposites are characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-vis spectrometry and fluorescence emission spectra. The results shows that TiO₂/ZrO₂ nanocomposites are composed of mainly anatase titania and tetragonal ZrO₂. Incorporating TiO₂ particles with ZrO₂ plays an important role in promoting the formation of nanoparticles with an anatase structure and leads to decreased fluorescence emission intensity. Most of the TiO₂/ZrO₂ nanocomposites exhibited comparable photocatalytic activity compared with commercial TiO₂ for the degradation aqueous methyl orange (MO) under ultraviolet irradiation, while the composite with Zr/Ti mass ratio of 15.2% shows the highest photocatalytic performances. Furthermore, the as-prepared nanocomposites can be reused with little photocatalytic activity loss. Without any further treatment besides rinsing, the photocatalytic activity of TiO₂/ZrO₂ (15.2%) composites is still higher than after five-cycle utilization.     

Photocatalytic and superhydrophilicity properties of N-doped TiO2 nanothin films

Pure TiO₂ and nitrogen doped titanium dioxide (N-TiO₂) thin films were prepared by sol-gel method through spin coating on soda lime glass substrates. TiCl₄ and urea were used as Ti and N sources in the sol. XRD results showed nitrogen doping has retarded anatase to rutile phase transformation. The doping also leads to a decrease in roughness of the samples from 4 nm (TiO₂) to 1 nm (N-TiO₂). However, surface analysis by statistical methods reveals that both surfaces have self-affine structure. Optical band gap of thin films was shifted from 3.65 eV (TiO₂) to 3.47 eV (N-TiO₂). Hydrophilic conversion and photocatalytic degradation properties of thin films were investigated and exhibited that N-TiO₂ thin film has more preferable hydrophilicity and photocatalytic properties under UV illumination.     

The surface properties and the activities in catalytic wet air oxidation over CeO2-TiO2 catalysts

No-noble metal CeO₂-TiO₂ catalysts prepared by sol-gel method were developed and examined for catalytic wet air oxidation (CWAO) of acetic acid. The structure of the catalysts was measured by BET, SEM, XRD, XPS and DTA-TG. We investigated the effect of the interactions of Ce and Ti on the structure of CeO₂-TiO₂ catalysts. The mechanisms of the relationships between the different content of Ti and the activity of CeO₂-TiO₂ catalysts were discussed. The results showed that the average crystal size of CeO₂ decreased and the surface areas increased; the low valence of Ce³⁺ increase, and the chemisorbed oxygen slightly decreased with the increase of Ti content on the surface of CeO₂-TiO₂ catalysts. The order of the activity in CWAO of acetic acid followed: Ce/Ti 1/1 > Ce/Ti 3/1 > Ce/Ti 1/3 > Ce/Ti 5/1 > CeO₂ > TiO₂ > no catalyst. In CWAO of acetic acid, the optimal atomic ratio of Ce and Ti was 1, and the highest COD removal was over 64% at 230 °C, 5 MPa and 180 min reaction time over Ce/Ti 1/1 catalyst. The excellent activity and stability of CeO₂-TiO₂ catalysts was observed in our study.     

Structure and photoluminescence properties of Er3+-doped TiO2-SiO2 powders prepared by sol-gel method

Er 3+-doped TiO 2-SiO 2 powders are prepared by the sol-gel method,and they are characterized by high resolution transmission electron microscopy (HR-TEM),X-ray diffraction (XRD) spectra,and Raman spectra of the samples.It is shown that the TiO 2 nanocrystals are surrounded by an SiO 2 glass matrix.The photoluminescence (PL) spectra are recorded at room temperature.A strong green luminescence and less intense red emission are observed in the samples when they are excited at 325 nm.The intensity of the emission,which is related to the defect states,is strongest at the annealing temperature of 800 C.The PL intensity of Er 3+ ions increases with increasing Ti/Si ratio due to energy transfer between nano-TiO 2 particles and Er 3+ ions.     

Structure and photocatalytic properties of copper-doped rutile TiO2 prepared by a low-temperature process

Copper-doped titania with variable Cu/Ti ratios have been prepared via a simple aqueous-phase method at 85 °C. The obtained products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and UV-vis absorption spectra analysis. The photocatalytic properties of the products were tested by photocatalytic degradation of aqueous brilliant red X-3B solution. The results showed that the sample with 2% copper doping has the best photocatalytic activity, which is 3 times that of undoped rutile titania. The effect of the doped copper on the structure and property of TiO₂ has also been discussed.     

Fabrication of TiO2 μ-donuts by sol-gel spin coating using a polymer mask

TiO₂ μ-donuts have been fabricated on glass and silicon substrates using polymer masks in combination with a sol-gel technique. Cylindrical poly(methyl methacrylate) (PMMA) nanopillars have been created using a composite polymer of polystyrene (PS) and PMMA followed by careful removal of the PS. Atomic force microscopy (AFM) analyses show that the height and diameter of the PMMA cylinders used as the mask are 440 ± 5 nm and 2.1 ± 0.2 μm, respectively. The cylindrical PMMA nanopillars have been coated with the sol of the TiO₂ precursor by a spin coating technique and annealed in air at elevated temperature to remove the PMMA mask. Removal of the PMMA mask has resulted in the formation of well ordered μ-donuts of TiO₂ on silicon surfaces. The interior and exterior heights of the TiO₂ μ-donuts are found to be 373 ± 152 nm and 457 ± 136 nm, respectively; and the interior and exterior diameters of the TiO₂ μ-donuts are found to be 1.33 ± 0.63 μm and 2.82 ± 0.50 μm, respectively. X-ray photoelectron spectroscopy (XPS) spectra of the TiO₂ μ-donuts as well as the smooth TiO₂ thin film showed signals from Ti and O confirming the presence of TiO₂ with Ti 2p_3/2 and O 1s peaks at 458.8 eV and 530.4 eV, respectively. The O 1s peak of the TiO₂ μ-donuts shows another peak at binding energy 532.0 eV due to SiO₂, as during annealing, the PMMA evaporates and the Si substrate is exposed. The X-ray diffractometer (XRD) pattern of the smooth TiO₂ thin film indicates that the anatase phase is present, with the characteristic peaks observed at 2θ values of 25.4°, 37.4°, and 48° corresponding to (1 0 1), (0 0 4), and (2 0 0) planes, respectively. UV-vis absorption spectra of TiO₂ μ-donuts on glass showed an unusual absorption of light in the visible region at ∼524 nm in addition to the usual UV absorption at ∼337 nm.     

Effect of heat treatment on morphology, crystalline structure and photocatalysis properties of TiO2 nanotubes on Ti substrate and freestanding membrane

Highly ordered titanium oxide (TiO₂) nanotubes were prepared by electrolytic anodization of titanium electrodes. Morphological evolution and phase transformations of TiO₂ nanotubes on a Ti substrate and that of freestanding TiO₂ membranes during the calcinations process were studied by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction microscopy. The detailed results and mechanisms on the morphology and crystalline structure were presented. Our results show that a compact layer exists between the tubular layer and Ti substrate at 600 °C, and the length of the nanotubes shortens dramatically at 750 °C. The freestanding membranes have many particles on their tubes during calcinations from 450 to 900 °C. The TiO₂ nanotubes on the Ti substrate transform to rutile crystals at 600 °C, while the freestanding TiO₂ membranes retain an anatase crystal with increasing temperature to 800 °C. The photocatalytic activity of TiO₂ nanotubes on a Ti substrate annealed at different temperatures was investigated by the degradation of methyl orange in aqueous solution under UV light irradiation. Due to the anatase crystals in the tubular layer and rutile crystals in the compact layer, TiO₂ nanotubes annealed at 450 °C with pure anatase crystals have a better photocatalytic activity than those annealed at 600 °C or 750 °C.     

Preparation and characterization of Fe-doped TiO2 on fly ash cenospheres for photocatalytic application

Fe³⁺-doped TiO₂ film deposited on fly ash cenosphere (Fe-TiO₂/FAC) was successfully synthesized by the sol-gel method. These fresh photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and thermogravimetric analyses (TGA). The XRD results showed that Fe element can maintain metastable anatase phase of TiO₂, and effect of temperature showed rutile phase appears in 650 °C for 0.01% Fe-TiO₂/FAC. The SEM analysis revealed the Fe-TiO₂ films on the surface of a fly ash cenosphere with a thickness of 2 μm. The absorption threshold of Fe-TiO₂/FACs shifted to a longer wavelength compared to the photocatalyst without Fe³⁺-doping in the UV-vis absorption spectra. The photocatalytic activity and kinetics of Fe-TiO₂/FAC with varying the iron content and the calcination temperatures were investigated by measuring the photodegradation of methyl blue (MB) during visible light irradiation. Compared with TiO₂/FAC and Fe³⁺-doped TiO₂ powder (Fe-TiO₂), the degradation ratio using Fe-TiO₂/FAC increased by 33% and 30%, respectively, and the best calcined temperature was 450 °C and the optimum doping of Fe/Ti molar ratio was 0.01%. The Fe-TiO₂/FAC particles can float in water due to the low density of FAC in favor of phase separation to recover these photocatalyst after the reaction, and the recovery test shows that calcination contributes to regaining photocatalytic activity of Fe-TiO₂/FAC photocatalyst.     

Preparation of continuous TiO2 fibers by sol-gel method and its photocatalytic degradation on formaldehyde

The continuous TiO₂ fibers were prepared by sol-gel method using the tetrabutyl orthotitanate as the precursor. The sol-formation process is studied by FT-IR spectroscopy. The synthesized continuous TiO₂ fibers were characterized using SEM, HRTEM and XRD. Results demonstrate that the titanate sol has good spinnability when R ≤ 2 (R = H₂O:Ti(OC₄H₉)₄, molar ratio). The fibers have the length of several meters and the diameter of about 30 μm. The fibers are a radial close-packed product of nano-particles with high crystallinity. The continuous TiO₂ fibers are co-crystal including anatase phase and rutile phase. The formaldehyde degradation ratio of continuous TiO₂ fiber was 98.6%.     

Synthesis and photocatalytic properties of porous TiO2 films prepared by ODA/sol-gel method

Porous TiO₂ films were deposited on SiO₂ pre-coated glass-slides by sol-gel method using octadecylamine (ODA) as template. The amount of ODA in the sol played an important role on the physicochemical properties and photocatalytic performance of the TiO₂ films. The films prepared at different conditions were all composed of anatase titanium dioxide crystals, and TiO₂ crystalline size got larger with increasing ODA amount. The maximum specific surface area of 41.5 m²/g was obtained for TiO₂ powders prepared from titanium sol containing 2.0 g ODA. Methyl orange degradation rate was enhanced along with increasing ODA amount and reached the maximal value at 2.0 g addition of ODA. After 40 min of UV-light irradiation, methyl orange degradation rate reached 30.5% on the porous film, which was about 10% higher than that on the smooth film. Porous TiO₂ film showed almost constant activity with slight decrease from 30.5% to 28.5% after 4 times of recycles.     

Stabilization of the anatase phase in TiO2(Fe, PEG) nanostructured coatings

Multilayered TiO₂(Fe³⁺, PEG) films were deposited on glass and SiO₂/glass substrates by sol-gel dipping method. The influence of Fe³⁺ and PEG(polyethylene glycol) concentrations, the number of layers, the thermal treatment time and the temperature on the optical and microstructural properties of the TiO₂ films were studied.As-deposited TiO₂(Fe³⁺, PEG) films were very porous, but after the thermal treatment at 500 °C, the PEG decomposed and burned out to porosity decreasing. Homogeneous nanostructured films were obtained, where the amorphous and the anatase phases coexist. XRD analysis showed that no rutile phase is observed in the films deposited on SiO₂/glass as compared with those deposited directly on glass and that the presence of the anatase phase in the films without PEG is more evident in the three-layers film. The XRD intensity of the main peak of anatase from 25° decreases with the increase of PEG concentration.The optical gap of the TiO₂(Fe³⁺, PEG) films is found in 2.52-2.56 eV range and does not essentially depend on the PEG content.     

Structural role of polyethylene glycol in the formation of anatase nanocrystalline titania at low temperature

Anatase nanocrystalline TiO₂ thin films were obtained by a sol–gel dip‐coating method, in which the nanocrystallization is effected by a simple hot water treatment of the deposited films at temperatures below 90 °C under atmospheric pressure for 1 h. The dip‐coating sol was prepared by reacting titanium tetra‐n‐butoxide [Ti(OⁿBu)₄] with polyethylene glycol (PEG) in ethanol. Films obtained from a sol that do not contain PEG show no sign of crystallization, demonstrating the importance of PEG in the crystallization process. Raman studies of reaction dynamics show that PEG undergoes a nucleophilic substitution reaction replacing butoxy groups in Ti(OⁿBu)₄. Stoichiometric reactions of Ti(OⁿBu)₄ with PEG in polar and nonpolar solvents were performed, and they yielded different titanium–PEG hybrid polymers, which were isolated and characterized by various spectroscopic techniques such as IR, Raman, solid‐state NMR and MALDI‐TOF‐MS. NMR studies evidenced the location and the way in which PEG is bonded with titanium atoms in the titanium–PEG hybrid polymers. On the basis of these studies, we have proposed structures for these polymers. It is demonstrated that the structure of the obtained polymers plays an important role in the formation of anatase TiO₂ nanoparticles in hot water at temperatures below 90 °C under atmospheric pressure. Copyright © 2009 John Wiley & Sons, Ltd.     

Effect of cobalt doping and annealing on properties of titania thin films prepared by sol-gel process

Undoped and cobalt doped titania (TiO₂) thin films have been prepared on Si(1 0 0) monocrystal and quartz substrate using the sol-gel deposition method and annealed in air at 450, 550, 650, 750, 850, 950 and 1050 °C. Several experimental techniques (AFM, XRD, Raman spectroscopy, XRR, EDX, XPS, XAS, UV-VIS spectroscopy) have been used to characterize these films. Further more the degree of light induced hydrophilicity was estimated by measuring the contact angle of a water droplet on the film. Increase of the annealing temperature and in smaller degree also cobalt doping predispose titania crystallite growth. The rutile phase was detected at lower temperatures in the cobalt doped films than in the undoped titania films. Cobalt in the cobalt doped TiO₂ was seen to be in Co²⁺ oxidation state, mainly in CoTiO₃ phase when films were annealed at temperatures higher than 650 °C. Cobalt compounds segregated into the sub-surface region and to the surface of the titania, where they formed islands. Cobalt doping red-shifted the fundamental absorption edge further into the visible range, however it did not enhance the light induced hydrophilicity of the thin film surface as compared to the undoped titania thin films.     

TiO2 thick films supported on reticulated macroporous Al2O3 foams and their photoactivity in phenol mineralization

TiO₂ thick films deposited on macroporous reticulated Al₂O₃ foams with pore size of 10 ppi and 15 ppi were prepared using dip coating from slurries of Aeroxide^® P25 nanopowder and precipitated titania. All prepared films have sufficiently good adhesion to the surface of the substrate also in case of strongly cracked films. No measurable release of deposited TiO₂ after repeated photocatalytic cycles was observed. The photocatalytic activity was characterized as the rate of mineralization of aqueous phenol solution under irradiation of UVA light by TOC technique. The best activity was obtained with Aeroxide^® P25 coated Al₂O₃ foam with the pore size of 10 ppi, annealed at 600 °C. The optimal annealing temperature for preparation of films from precipitated titania could be determined at 700 °C. Films prepared by sol-gel deposition technique were considerably thinner compared to coatings made of suspensions and their photocatalytic activity was significantly smaller.     

Synthesis, characterization and degradation of Bisphenol A using Pr, N co-doped TiO2 with highly visible light activity

Praseodymium and nitrogen co-doped titania (Pr/N-TiO₂) photocatalysts, which could degrade Bisphenol A (BPA) under visible light irradiation, were prepared by the modified sol-gel process. Tetrabutyl titanate, urea and praseodymium nitrate were used as the sources of titanium, nitrogen and praseodymium, respectively. The resulting materials were investigated by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), UV-vis absorbance spectroscopy, X-ray photoelectron spectroscopy (XPS), N₂ adsorption-desorption isotherm and Fourier transform infrared spectra (FTIR). It was found that Pr doping inhibited the growth of crystalline size and the transformation from anatase to rutile. The degradation of BPA under visible light illumination was taken as probe reaction to evaluate the photo-activity of the co-doped photocatalyst. In our experiments, the optimal dopant amount of Pr was 1.2 mol% and the calcination temperature was 500 °C for the best photocatalytic activity. Pr/N-TiO₂ samples exhibited enhanced visible-light photocatalytic activity compared to N-TiO₂, undoped TiO₂ and commercial P25. The nitrogen atoms were incorporated into the crystal of titania and could narrow the band gap energy. Pr doping could slow the radiative recombination of photogenerated electrons and holes in TiO₂. The improvement of photocatalytic activity was ascribed to the synergistic effects of nitrogen and Pr co-doping.     

Structure and dielectric studies of nano-composite Fe2O3: BaTiO3 prepared by sol-gel method

Nano-structure pure barium titanate (BaTiO₃) and that was doped with iron oxide (Fe₂O₃), have been prepared by sol-gel method, using barium acetate (Ba(Ac)₂) and titanium butoxide (Ti(C₄H₉O)₄), as precursors. The as-grown prepared samples by sol-gel technique were found to be amorphous, which crystallized to the tetragonal phase after synthesized at 750 °C in air for 1 h as detected from the XRD patterns. The XRD data were confirmed by transmission electron microscope (TEM). The dielectric properties namely; dielectric constant (ε′) and loss tangent (tan δ) in the frequency range between 42 Hz and 1 MHz, at range of temperature 25-250 °C were investigated. The temperature dependence of ε′ and tan δ for the undoped and doped materials, at 1 kHz, was also investigated. As a result, tan δ increased rapidly with decreasing temperature below 125 °C (Curie temperature) while above this temperature, tan δ shows temperature independent. As a result, below and above Curie temperature, ferroelectric phase and paraelectric phase of BaTiO₃ can be obtained, respectively.