丙烯酸水溶液聚合法制备PTFE/PAA/Nafion膜及其性能

采用廉价的多孔聚四氟乙烯(PTFE)膜作为基底, 用少量的Nafion与PTFE膜复合可制备低成本的质子膜. 但疏水性的PTFE膜与亲水性的Nafion膜结合性不佳. 基于此, 本文对疏水性的PTFE膜材料表面进行设计, 先采用丙烯酸对疏水性的PTFE膜表面进行亲水性改性, 再喷涂亲水性Nafion膜, 完成低成本PTFE/PAA/Nafion膜的制备. 实验结果表明, 改性前的PTFE膜材料水接触角为150°, 改性后的膜接触角变为55.6°, 亲水性大幅上升, 膜的机械强度和尺寸稳定性(断裂强度为25.2 MPa, 80 ℃下的溶胀率为11.9%)均优于Nafion117膜, 而 Nafion用量则节省了60%. PTFE/PAA/Nafion膜具有高质子导通率(80 ℃下达到131.9 mS/cm), 接近于Nafion117膜, 最大功率密度可以达到404.2 mW/cm².     

质子交换膜燃料电池Nafion/PTFE复合膜的研究

在聚四氟乙烯(PTFE)多孔膜内浸入Nafion树脂,制成Nafion/PTFE复合膜用于质子交换膜燃料电池(PEMFC).该复合膜的Nafion含量在50%左右,在干态和湿态时的拉伸强度及水化/脱水过程中,其尺寸稳定性比Nafion均有所提高.在80 ℃,H2/O2压力为0.2/0.2 MPa条件下,用25 μm厚复合膜组装的电池性能优于Nafion117膜组装电池的性能.测量了复合膜的O2渗透率和含水量并与Nafion膜的性能作了比较.     

SPES/PWA/SiO_2复合质子交换膜的性能

以磺化聚醚砜(SPES)为基体,以不同比例的SiO2溶胶与磷钨酸(PWA)为掺杂物,制备了一种有望用于直接甲醇燃料电池(DMFC)的新型SPES/PWA/SiO2有机-无机复合膜,并经热失重分析(TGA)、差示扫描量热仪(DSC)、扫描电镜(SEM)-X射线能谱分析(EDX)等对膜的结构和性能进行了表征,探讨了复合膜用作质子交换膜的可能性.结果表明:复合膜较纯SPES膜具有更高的热稳定性、玻璃化转变温度和吸水率;虽然在室温和电池操作温度(80℃)下,复合膜的拉伸强度均低于纯SPES膜,但即使当SiO2含量高达20%(w)时,复合膜的拉伸强度仍高于Nafion112膜的;SEM图片显示SiO2和PWA在膜中分布均匀,这将有利于连续质子传输通道的形成.对于SiO2含量为15%(w),PWA含量为6%(w)的复合膜,其室温质子传导率达到了0.034S·cm-1,与Nafion112膜的相当,但其甲醇渗透率明显降低,仅为商用Nafion112膜的七分之一左右,这表明该复合膜在直接甲醇燃料电池中具有良好的应用前景.     

全钒氧化还原液流电池用Nafion/有机硅复合膜

采用原位化学反应的方法制备了Nafion/有机硅复合膜, 并对所制备复合膜的离子交换容量(IEC)、电导率和水渗透率等进行了测试. 结果表明, 所制备复合膜具有优异的阻水性能. 以Nafion/有机硅复合膜作为离子交换膜的钒电池的库仑效率(CE)和能量效率(EE)都得到了大幅度提高. 此外, 以所制备复合膜为离子交换膜的VRB单电池充放电80次后性能几乎无衰减, 说明所制备Nafion/有机硅复合膜即使在强酸和强氧化性的钒电池体系中也可以稳定使用, 表明Nafion/有机硅复合膜是一种性能优异的适用于全钒氧化还原液流电池的新型质子交换膜.     

硅氧烷交联的咪唑基团功能化聚苯醚/聚四氟乙烯耐高温质子交换膜

以聚苯醚(PPO)为基体材料, 通过溴甲基化及咪唑基团功能化, 与聚四氟乙烯(PTFE)复合、 硅氧烷基团水解交联及磷酸掺杂, 制备了兼具高磷酸掺杂含量、 高质子电导率和良好机械性能的高温质子交换膜材料. 以甲基咪唑(MeIm)和咪唑基硅氧烷化合物(SiIm)为功能化试剂(其中咪唑基团提供了磷酸作用位点, 同时SiIm中的硅氧烷基团水解后得到Si—O—Si交联网络结构), 提高了膜材料的机械稳定性. 与PTFE的复合进一步增强了膜材料的机械强度. 结果表明, 复合膜具有较高的电导率和一定的机械强度. 当磷酸掺杂质量分数为242.5%时, PPO-50%SiIm-50%MeIm/PTFE复合膜在160 ℃不加湿条件下的电导率为0.09 S/cm, 室温下的断裂拉伸强度为3.6 MPa.     

含氨基聚芳醚酮/磺化聚芳醚酮砜中高温质子交换复合膜的制备与性能研究

以自制的高磺化度磺化聚芳醚酮砜(SPAEKS)和含有氨基的聚芳醚酮(Am-PAEK)为原料,通过共溶剂涂膜法制备了不同重量比例的Am-PAEK/SPAEKS复合膜.通过高温(160℃)处理使氨基和磺酸基团在复合膜内形成交联,制得交联型复合膜.复合膜的热性能、尺寸稳定性、阻醇性能有所提高,而且交联型复合膜中的Am-PAEK/SPAEKS-C-3质子传导率在120℃时达到了0.0892 S/cm,高于在相同测试条件下SPAEKS膜的0.0654 S/cm和Nafion膜的0.062 S/cm,而其甲醇渗透系数在25℃时达到0.14×10-6cm2/s,低于SPAEKS膜的0.85×10-6cm2/s和Nafion膜的2×10-6cm2/s.实验结果表明,Am-PAEK/SPAEKS交联型复合膜有望在中高温质子交换膜燃料电池中得到应用.     

全钒氧化还原液流电池Nafion/SiO_2复合膜的研究

采用溶胶-凝胶法制备Nafion117/SiO2复合膜.工艺研究表明:复合膜制备过程中,加入的MeOH与TEOS比例基本不影响复合膜的阻钒性能.但如以水解时间10 min,水解完成后自然晾干24 h制备的复合膜,则其VO2+的渗透率最低,为4.27×10-9cm2/s,比Nafion117膜的渗透率降低了52倍.SEM测试表明,经自然晾干的复合膜,其中SiO2晶粒长大,并填充了Nafion膜中大部分的孔洞.以其作隔膜组装全钒氧化还原液流电池(单电池),测试表明膜掺杂后电池的电力效率提高2.7%.     

聚合物电解质膜燃料电池薄电极制备技术的研究

为降低聚合物电解质膜燃料电池 (PEMFC)电极中铂的载量 ,本文建立一种新的薄电极制备技术 (TEFT) ,制备了表面平滑、颗粒分布均匀的低铂载量电极 .结果表明当电极的铂载量为 1mg/cm2 ,用Nafion 117膜作电解质时 ,电池的最大功率密度达 0 30W·cm-2 .系统地考察了阴极中不同PTFE和Nafion含量对PEMFC性能的影响 .     

不同EW值的sPTFS/PTFE复合膜性能研究

将两种不同EW值的聚α,β,β＿三氟苯乙烯(sPTFS)树脂浸入到多孔聚四氟乙烯(PTFE)膜的孔中,制成sPTFS/PTFE复合膜用于质子交换膜燃料电池(PEMFC).并对该复合膜的吸水率,电导率,机械强度及其装配的电池性能进行了测试.与其它均质膜相比,复合膜明显降低了吸水率,同时也降低了电导率,增加了机械强度.在电池温度为80℃,H2/O2压力为0.2/0.2MPa条件下,两种复合膜装配电池的性能优于Nofion 115膜.低EW值的复合膜电池性能优于高EW值的电池性能,但电池稳定性相对较差.     

SSPEEK/Na-MMT复合钒电池质子交换膜的制备与性能研究

以含有异丙基溴侧基的聚醚醚酮为原子转移自由基聚合(ATRP)大分子引发剂,通过ATRP法在聚醚醚酮主链上接枝引入聚苯乙烯磺酸钠侧链,得到侧链型磺化聚醚醚酮质子交换膜(SSPEEK).采用溶液共混法在SSPEEK膜中引入钠基蒙脱土(Na-MMT),制备SSPEEK/Na-MMT钒电池质子交换复合膜.热重分析表明,复合膜具有较好的耐热性;扫描电镜显示,Na-MMT均匀分散在SSPEEK中.复合膜的钒离子渗透率由SSPEEK膜的1.24×10-5cm2·min-1降为4.88×10-6cm2·min-1,低于Nafion117膜的钒离子渗透率,阻钒能力优于Nafion117膜.电流密度为30 m A·cm-2时,以复合膜组装的电池的放电时间为215 min,长于Nafion117膜的198 min.在高放电电流密度下SSPEEK/Na-MMT膜的库伦效率与Nafion117膜相当.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.