聚吡咯/聚苯胺复合型导电聚合物防腐蚀性能

采用循环伏安法,在含吡咯和苯胺的0.3 mol/L草酸水溶液中制备了聚吡咯/聚苯胺(PPy/Pani)的复合型导电聚合膜。采用红外光谱、极化曲线、自腐蚀电位-时间曲线、扫描电子显微镜和电化学阻抗谱研究了共聚膜的防腐蚀性能。结果表明,在1 mol/L H2SO4中,PPy、Pani与不锈钢基体发生氧化还原反应,促进不锈钢表面发生钝化;当苯胺与吡咯浓度比为1∶3时,制备得到的复合型导电聚合膜所保护的不锈钢自腐蚀电流最小,自腐蚀电位最高,保护时间最长。PPy、Pani及其共聚膜在3.5%NaCl溶液中电化学阻抗谱表明,所制备的PPy、Pani及其共聚物膜与不锈钢基体发生氧化还原反应,使其表面钝化;当Cl-到达不锈钢表面时,破坏钝化膜导致不锈钢腐蚀。     

聚吡咯/聚苯胺二元复合纳米管及其热电性能

以甲基橙为软模板, 六水合三氯化铁为催化剂, 在水溶液中通过沉淀聚合法制备了管径为20~180 nm的聚吡咯(PPy)纳米管; 以聚吡咯纳米管为基体, 通过原位聚合制备了聚吡咯/聚苯胺(PPy/PANi)二元复合纳米管. 研究发现, 在PPy/PANi二元复合纳米管中, PANi均匀地包覆在PPy纳米管表面, 并形成有序堆积, PPy与PANi间存在强烈的π-π共轭作用与氢键作用, 当PPy与PANi单体摩尔比为1∶2时, PPy/PANi二元复合纳米管的功率因子在363 K时达到0.74 μW/(m·K ²).     

天然海水中聚吡咯膜的防微生物附着及防腐蚀性能

采用恒电流法在316 L不锈钢电极表面合成聚吡咯(PPy), 通过开路电位、 生物显微镜(BM)、 Tafel极化曲线及电化学交流阻抗(EIS)研究了聚吡咯防止微生物附着及防腐蚀特性. 研究表明, 沉积聚吡咯的316 L不锈钢电极浸泡在天然海水中(0~20 d), 开路电位基本保持不变, 表明电化学合成的聚吡咯膜有良好的防止微生物附着能力, 并通过生物显微镜进行了验证, 且在浸泡的过程中其腐蚀电流密度维持在10^-7 mA/cm², 表现出良好的防腐蚀特性; 浸泡50 d后, 其防腐蚀效率仍高达97.45%. 因此, 电化学合成的聚吡咯具有优异的防止微生物附着和防腐蚀特性.     

聚合溶液pH值对染料敏化太阳电池中聚吡咯对电极结构和性能的影响

电化学合成聚吡咯(PPy)时,聚合电解液的pH值对PPy薄膜的形貌和性质有较大的影响,进而影响PPy薄膜对I-/I3-的电催化活性以及基于PPy对电极(CE)的染料敏化太阳电池(DSSCs)的光电转换性能.本文采用电化学恒电位方法,在掺杂氟的SnO2(FTO)导电玻璃上合成出了对甲苯磺酸根离子掺杂的聚吡咯(PPyTsO)电极,并将其作为DSSCs的对电极.通过改变吡咯聚合时聚合电解液的pH值,借助扫描电镜(SEM)、紫外-可见(UV-Vis)吸收光谱、X-射线光电子能谱(XPS)和循环伏安(CV)等表征技术,详细探讨了聚合溶液pH值对PPy CE形貌、结构及其对I-/I3-的电催化性能的影响.研究发现在pH 2.0下合成的聚吡咯对阴离子掺杂率最高且链共轭性最佳,具有对I-/I3-氧化还原介质最强的催化能力,基于此PPy CE的电池光电转化效率也最高.pH值太大或太小都不利于生成具有高掺杂率和高催化活性的PPy电极,组装成DSSCs后的光电转换效率也较低.     

聚吡咯/TiO2纳米管阵列复合电极制备条件对其光电性能的影响

通过阳极氧化法制备TiO2纳米管阵列(TNTA),静态下采用电化学方法在TNTA表面修饰聚吡咯(PPy)。并用扫描电子显微镜(SEM)、红外透射光谱(FTIR)、紫外可见漫反射吸收光谱(UV-Vis)等表征手段对复合材料进行表征。结果显示,PPy和TiO2之间存在强烈的相互作用,PPy修饰的TNTA发生了红移,并且增强了其在整个可见光区的吸收。确定了影响PPy/TNTA复合电极光电性能的因素(聚合时间、聚合温度、聚合电位、电解质浓度等),通过测定连续瞬间电流-时间曲线的方法,考察了制备条件对复合材料光电性能的影响。初步探讨出PPy提高TNTA光电性能的机理。     

固相法制备聚噻吩/聚吡咯/二氧化钛膜及电化学腐蚀性能

在水蒸气气氛下,制备出表面富含羟基的纳米Ti O_2颗粒,然后在室温和氧化剂三氯化铁存在下,通过化学固相氧化法,在不锈钢表面制备出聚噻吩/聚吡咯/Ti O2(PTH/PPy/TiO_2)薄膜。采用X射线衍射(XRD)、扫描电子显微镜(SEM)、傅里叶变换红外光谱(FT-IR)、热重分析(TG)、电化学阻抗(EIS)等技术手段对产物的微观形貌、热稳定性和耐腐蚀性能进行了研究,并讨论了不同纳米TiO_2含量对复合材料的结构和性能的影响。结果表明,在其使用温度(20~300℃)下,PTH/PPy/6%Ti O_2(质量分数)膜热分解温度为450℃,能够满足其使用要求。用PTH/PPy/TiO_2膜保护的不锈钢比裸露的不锈钢的自腐蚀电位高出0.8 V以上,而腐蚀电流密度降低了2个数量级。TiO_2的添加明显的提高了PTH/PPy材料的抑制腐蚀的能力,并且由于TiO_2的加入能够使聚合物与无机纳米粒子之间能够紧密地结合在一起,减少膜的缺陷,增大复合材料与金属基体的力学性能,使得膜结构更加的致密,从而减缓不锈钢的腐蚀。     

纳米结构ZnO/染料/聚吡咯光阳极的光电化学性质

用光电化学方法研究了染料RuL2 (NCS) 2 (L =2 ,2′ bipydine 4,4′ dicarboxylicacid) (简写为Dye)、聚吡咯 (PPy)敏化氧化锌 (ZnO)纳米晶电极以及用RuL2 (NCS) 2 和PPy复合敏化ZnO纳米晶膜电极的光电化学行为 .实验表明 ,ZnO/PPy纳米多孔膜电极为双层n 型半导体结构 .PPy和RuL2(NCS) 2 都可对ZnO纳米晶膜产生敏化作用 ,ZnO/RuL2 (NCS) 2 /PPy复合多孔膜电极产生的光电流远大于ZnO/PPy纳米多孔膜电极和ZnO/Dye多孔膜电极产生的光电流 .讨论了该电极的光生电子的机理 ,初步测定了ZnO/RuL2 (NCS) 2 /PPy电极作为光阳极的光电化学电池的工作特性曲线 ,测得该电池的光电转换效率为 1 .3% ,填充因子为 0 .75 .     

不同状态下聚吡咯膜的电化学阻抗

用恒电流法分别聚合了掺杂对甲苯磺酸根(pTS-)和十二烷基磺酸根(DS-)的聚吡咯膜(PPy/pTS和PPy/DS),通过循环伏安法(CV)和电化学阻抗法(EIS)测试了聚吡咯膜在NaCl溶液中‘过电位’电化学过程前后及不同电位下聚吡咯膜的电化学性能.同时,通过嵌入和脱出Na+和Cl-离子的聚吡咯膜在特定溶液中电化学阻抗图谱,研究了离子的嵌入对聚吡咯膜电化学性能的影响.结果表明‘过电位’现象可以提高聚吡咯膜的离子电导率和膜电容,Cl-离子的嵌入能提高PPy/pTS的电导率,而Na+离子的嵌入对聚吡咯膜的电导率影响不大.另外,嵌入离子对聚吡咯膜形貌的改变会对聚吡咯膜的离子传导率有一定影响,从而导致膜的电化学阻抗的变化.     

电化学控制产生纳米氧气气泡及其对电化学聚合吡咯形貌的影响

利用原位电化学原子力显微镜(in-situ EC-AFM)研究了纳米氧气气泡在高定向热解石墨(HOPG)表面的电化学控制产生与生长. AFM原位图像表明电化学产生的氧气在HOPG表面形成了纳米气泡, 并且纳米气泡的产生与生长可以通过改变外加电压和反应时间来进行控制. 随后, 研究了电化学产生的纳米氧气气泡对于在HOPG表面电化学聚合吡咯反应的影响, 结果表明伴随聚合反应过程产生的纳米氧气气泡使得生成的聚吡咯膜表面形成了气泡状的缺陷.     

溶胶-凝胶法制备改性TiO2纳米薄膜及其防腐蚀性能

应用溶胶-凝胶法和浸渍提拉技术在316L不锈钢表面分别制备TiO2纳米膜和 B-Fe-Ce改性的TiO2纳米膜. 采用场发射扫描电子显微镜(FE-SEM)、原子力显微镜(AFM)、拉曼光谱法和能量分散谱(EDS)对薄膜进行表征,通过电化学阻抗谱(EIS)和动电位阳极极化曲线的测试考察薄膜的耐蚀性及对不锈钢的保护性能. 结果表明:两种纳米薄膜均含锐钛矿型的TiO2纳米颗粒,纯TiO2纳米膜与改性后的纳米膜中颗粒直径分别约为15和10 nm. TiO2/316L不锈钢和 B-Fe-Ce-TiO2/316L不锈钢膜电极浸泡在0.5 mo.lL-1 NaCl溶液后,后者的电化学反应电阻较大,动电位阳极极化曲线的稳定钝化区较宽,击穿电位更高,说明改性的纳米膜的耐蚀性及其保护性能更好.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.