Enantioselective piezoelectric quartz crystal sensor for d-methamphetamine based on a molecularly imprinted polymer

A piezoelectric quartz crystal (PQC) sensor based on a molecularly imprinted polymer (MIP) has been developed for enantioselective and quantitative analysis of d-(+)-methamphetamine (d(+)-MA). The sensor was produced by bulk polymerization and the resulting MIP was then coated on the gold electrode of an AT-cut quartz crystal. Conditions such as volume of polymer coating, curing time, type of PQC, baseline solvent, pH, and buffer type were found to affect the sensor response and were therefore optimized. The PQC-MIP gave a stable response to different concentrations of d(+)-MA standard solutions (response time = 10 to 100 s) with good repeatability (RSD = 0.03 to 3.09%; n = 3), good reproducibility (RSD = 3.55%; n = 5), and good reversibility (RSD = 0.36%; n = 3). The linear range of the sensor covered five orders of magnitude of analyte concentration, ranging from 10⁻⁵ to 10⁻¹ μg mL⁻¹, and the limit of detection was calculated as 11.9 pg d(+)-MA mL⁻¹ . The sensor had a highly enantioselective response to d(+)-MA compared with its response to l(−)-MA, racemic MA, and phentermine. The developed sensor was validated by applying it to human urine samples from drug-free individuals spiked with standard d(+)-MA and from a confirmed MA user. Use of the standard addition method (SAM) and samples spiked with d(+)-MA at levels ranging from 1 × 10⁻³ to 1 × 10⁻² μg mL⁻¹ showed recovery was good (95.3 to 110.9%).     

Development of molecularly imprinted polymer films used for detection of profenofos based on a quartz crystal microbalance sensor

A quartz crystal microbalance (QCM) sensor based on molecularly imprinted ultra-thin films was developed for detecting profenofos in real samples. Films prepared by physical entrapment (MIP-A) and in situ self-assembly (MIP-B) were compared. The results indicated that the best sensing signal was obtained through the in situ self-assembly method. The QCM sensor chip was pretreated with 11-mercaptoundecanoic acid (MUA) to form a self-assembled monolayer (SAM), and then polymer films were immobilized directly on the SAM using surface-initiated radical polymerization. In this paper, all detection experiments were taken in air. The reaction was processed in solution, and the electrode was washed with deionized water and dried with N(2) before QCM measurement. The film was characterized by a scanning electron microscope (SEM), AC impedance and cyclic voltammetry. Analysis of the QCM response in the presence of different concentrations of profenofos showed a good linear correlation during 1.0 × 10(-8) to 1.0 × 10(-5) mg mL(-1) (y = 5log x + 42.5, R = 0.9960) and 1.0 × 10(-5) to 1.0 × 10(-3) mg mL(-1) (y = 25.86log x + 146, R = 0.9959), respectively. The MIP-QCM sensor was used to detect profenofos in tap water, and showed good recovery and repeatability.     

Biomimetic piezoelectric quartz sensor for caffeine based on a molecularly imprinted polymer

A piezoelectric quartz sensor coated with molecularly imprinted polymer (MIP) for caffeine was developed. The MIP was prepared by co-polymerizing methacrylic acid (MAA) and ethylene glycol dimethacrylate (EDMA) in the presence of azobis(isobutyronitrile) as initiator, caffeine as template molecule, and chloroform as solvent. The MIP suspension in polyvinyl chloride/tetrahydrofuran (6:2:1 w/w/v) solution was spin coated onto the surface of the electrode of a 10 MHz AT-cut quartz crystal. The sensor exhibited a linear relationship between the frequency shift and caffeine concentration in the range of 1×10^–7 mg mL^–1 up to 1x10^–3 mg mL^–1 [correlation coefficient (r)=0.9935] in a stopped flow measurement mode. It has a sensitivity of about 24 Hz/ln(concentration, mg mL^–1). A steady-state response was achieved in less than 10 min. The performance characteristic of the sensor shows a promising and inexpensive alternative method of detecting caffeine. Surface studies were carried out for the reagent phase of the sensor using SEM, AFM, and XPS analysis in order to elucidate the imprinting of the caffeine molecule. The SEM micrograph, AFM image, and XPS spectra confirmed the removal of caffeine by Soxhlet extraction in the imprinting process and the rebinding of caffeine to the MIP sensing layer during measurement.     

Acetylsalicylic acid electrochemical sensor based on PATP-AuNPs modified molecularly imprinted polymer film

A novel electrochemical sensor based on molecularly imprinted polymer film has been developed for aspirin detection. The sensitive film was prepared by co-polymerization of p-aminothiophenol (p-ATP) and HAuCl(4) on the Au electrode surface. First, p-ATP was self-assembled on the Au electrode surface by the formation of Au-S bonds. Then, the acetylsalicylic acid (ASA) template was assembled onto the monolayer of p-ATP through the hydrogen-bonding interaction between amino group (p-ATP) and oxygen (ASA). Finally, a conductive hybrid membrane was fabricated at the surface of Au electrode by the co-polymerization in the mixing solution containing additional p-ATP, HAuCl(4) and ASA template. Meanwhile, the ASA was spontaneously imprinted into the poly-aminothiophenol gold nanoparticles (PATP-AuNPs) complex film. The amount of imprinted sites at the PATP-AuNPs film significantly increases due to the additional replenishment of ASA templates. With the significant increasing of imprinted sites and doped gold nanoparticles, the sensitivity of the molecular imprinted polymer (MIP) electrode gradually increased. The molecularly imprinted sensor was characterized by electrochemical impedance spectroscopy (EIS), differential pulse voltammetry (DPV), and cyclic voltammetry (CV). The linear relationships between current and logarithmic concentration were obtained in the range from 1 nmol L(-1) to 0.1 μmol L(-1) and 0.7 μmol L(-1) to 0.1 mmol L(-1). The detection limit of 0.3 nmol L(-1) was achieved. This molecularly imprinted sensor for the determination of ASA has high sensitivity, good selectivity and reproducibility, with the testing in some biological fluids also has good selectivity and recovery.     

Potentiometric propranolol-selective sensor based on molecularly imprinted polymer

A novel potentiometric sensor based on molecularly imprinted polymer (MIP) for propranolol, an adrenergic-blocking drug, was designed. The influence of molecularly imprinted polymer particle content and sodium tetraphenylborate additives in polyvinylchloride membrane was shown. The electrodes show near-Nernstian responses down to 10^?4–10^?5?M propranolol concentration. The potentiometric response of MIP-based sensor for propranolol in mixed nonaqueous medium was shown at first. Sensor selectivity relative to various inorganic cations, atenolol and metoprolol, was reported. Direct potentiometry was used to determine propranolol in aqueous modeling solutions and pharmaceutical preparations with good results.     

Selective sensing of triazine herbicides in imprinted membranes using ion-sensitive field-effect transistors and microgravimetric quartz crystal microbalance measurements

A series of triazine herbicides consisting of the chlorotriazine atranex (atrazine), (1), prozinex, (2), tyllanex, (3), simanex, (4) and the methylthiolated triazines ametrex, (5), prometrex, (6) and terbutex, (7), were imprinted in an acrylamide-methacrylate copolymer. The polymer was deposited on the gate surface of ion-sensitive field-effect transistors (ISFETs) and piezoelectric Au-quartz crystals. Selective sensing of the imprinted substrates was accomplished by the imprinted polymer membrane associated with the ISFETs and Au-quartz crystals. Binding of the substrates onto the imprinted polymer associated with the gate of the ISFET alters the electrical charge and potential of the gate interface, thus allowing the potentiometric transduction of the binding events. The association of the substrates with the imprinted membrane linked to the Au-quartz crystal results in the membrane swelling, thus enabling the microgravimetric quartz crystal microbalance assay of the substrate binding events. The specificity of the imprinted recognition sites is attributed to complementary H-bond and electrostatic interactions between the substrates and the acrylamide-methacrylic acid copolymer.     

Development of a sensor for calcium based on quartz crystal microbalance

A new sensor for calcium based on a piezoelectric quartz crystal is presented. The selectivity depends on the ratio lipophilic salt/ionophore of the composition of the coating of the quartz crystal. A crystal coated with a THF solution of PVC (34.5% w/w), DOS (62.1% w/w) and 10,19-bis[(octadecylcarbamoyl) methoxyacetyl]-1,4,7,13,16-pentaoxa-10,19-diaza cycloheneicosane (3.4% w/w) and a salt/ionophore molar proportion of 60%, corresponding to a frequency decrease of the dry crystal of 6.0 kHz, showed a detection limit to calcium of 2.2 mg/L. Both a standard calcium chloride solution and a commercially balanced salt solution for tissue culture were analyzed subsequent to ion chromatographic separation. The results obtained with the sensor developed were compared with those obtained with a conductivity detector. Although the results from both detectors agreed for the standard solution, only the quartz crystal sensor was able to give reliable results for the tissue culture solution.     

An optical reflected device using a molecularly imprinted polymer film sensor

A novel and highly selective optical sensor with molecularly imprinted polymer (MIP) film was fabricated and investigated. The optical sensor head employing a medium finesse molecularly imprinted polymer film has been fabricated and characterised. A blank polymer and formaldehyde imprinted polymer were using methacrylic acid as the functional monomer and the ethylene glycol dimethacrylate as a crosslinker. The transduction mechanism is discussed based on the changes of optical intensity of molecularly imprinted polymer film acting as an optical reflected sensor. Template molecules, which diffused into MIP, could cause film density, and refractive index change, and then induce measurable optical reflective intensity shifts. Based on the reflective intensity shifts, an optical reflection detection of formaldehyde was achieved by illuminating MIP with a laser beam. For the same MIP, the reflective intensity shift was proportional to the amount of template molecule. This optical sensor, based on an artificial recognition system, demonstrates long-time stability and resistance to harsh chemical environments. As the research moves forward gradually, we establish the possibilities of quantitative analysis primly, setting the groundwork to the synthesis of the molecular imprinted optical fiber sensor. The techniques show good reproducibility and sensitivity and will be of significant interest to the MIPcommunity.     

Development of a sensor for calcium based on quartz crystal microbalance

A new sensor for calcium based on a piezoelectric quartz crystal is presented. The selectivity depends on the ratio lipophilic salt/ionophore of the composition of the coating of the quartz crystal. A crystal coated with a THF solution of PVC (34.5% w/w), DOS (62.1% w/w) and 10,19-bis[(octadecylcarbamoyl) methoxyacetyl]-1,4,7,13,16-pentaoxa-10,19-diaza cycloheneicosane (3.4% w/w) and a salt/ionophore molar proportion of 60%, corresponding to a frequency decrease of the dry crystal of 6.0 kHz, showed a detection limit to calcium of 2.2 mg/L. Both a standard calcium chloride solution and a commercially balanced salt solution for tissue culture were analyzed subsequent to ion chromatographic separation. The results obtained with the sensor developed were compared with those obtained with a conductivity detector. Although the results from both detectors agreed for the standard solution, only the quartz crystal sensor was able to give reliable results for the tissue culture solution.     

基于分子印迹技术的丙溴磷压电石英晶体微天平研制

介绍了一种用于检测丙溴磷农药的分子印迹压电生物传感器的构建方法。采用沉淀聚合法合成了农药丙溴磷的分子印迹聚合物,将其固定于石英晶体微天平电极表面构建传感器;采用环境扫描电镜以及原子力显微镜对聚合物形貌、传感器电极表面形貌特征进行分析,并利用传感器对丙溴磷农药进行检测分析,其质量浓度在10~1000 ng/mL范围内,传感器频率改变与丙溴磷浓度之间的响应呈线性关系,线性方程为y=0.139ρ+2.26(r=0.9984)。结果表明,构建的分子印迹压电生物传感器能够对农药进行初步检测,具有较高的灵敏性和较好的特异识别能力。     

聚苯胺分子印迹膜电化学传感器检测氯霉素

以苯胺为功能单体和交联剂,氯霉素(chloramphenicol,CAP)为模板分子,采用电化学聚合法(循环伏安法)在金电极上合成了对CAP具有快速响应能力的聚苯胺分子印迹膜;结合差示脉冲伏安法建立了针对氯霉素的检测方法,并将所制备的聚苯胺分子印迹膜用作电化学传感器以测定氯霉素眼药水中的氯霉素.结果表明,所制备的聚苯胺分子印迹膜具有制备简单、响应快速、灵敏度高、再生性能良好等特点;其对氯霉素眼药水中的氯霉素的检测结果令人满意,有望用于实际样品中氯霉素的检测.     

Piezoelectric atrazine sensor based on a molecularly imprinted film of titanium dioxide

We have developed a piezoelectric sensor for the determination of atrazine. It is based on the modification of a molecularly imprinted film of TiO₂ that was placed on a quartz crystal via a surface sol?Cgel process. The resulting sensor exhibits high selectivity for atrazine, a re-usability that is better than that of other sensors, a response time of 3?min, a wider linear range (0.0005?C8?mM), and a lower detection limit (0.1???M). The analytical application of the atrazine sensor confirms the feasibility of atrazine determination.

Bulk acoustic wave sensor for herbicide assay based on molecularly imprinted polymer

A novel molecularly imprinted polymer (MIP) coated bulk acoustic wave (BAW) sensor was fabricated for liquid phases. It can be used as a sensitive portable implement for the assay of 2,4-dichlorophenoxyacetic acid. A logarithmic response relationship between 2.0 × 10^–7 M and 5.0 × 10^–4 M was found. The detection limit was 1.0 × 10^–7 M. Recoveries were 93.2–108.7%. Influencing factors were investigated in detail and optimized.     

葛根素分子印迹电化学传感器的制备及研究

以丙烯酰胺为功能单体,葛根素为模板分子,马来松香丙烯酸乙二醇酯为交联剂,采用循环伏安法合成了葛根素分子印迹膜,并以此为识别元件制备了葛根素电化学传感器。该传感器对葛根素具有高度的选择性和良好的敏感度,葛根素氧化峰电流与其浓度在6.0×10-8～1.6×10-3mol/L范围内呈良好的线性关系,检出限为2.0×10-8mol/L。将此传感器用于葛根素注射液和木瓜葛根片中葛根素的含量测定,回收率为97.7%～106.4%。     

Bulk acoustic wave sensor for herbicide assay based on molecularly imprinted polymer

A novel molecularly imprinted polymer (MIP) coated bulk acoustic wave (BAW) sensor was fabricated for liquid phases. It can be used as a sensitive portable implement for the assay of 2,4-dichlorophenoxyacetic acid. A logarithmic response relationship between 2.0 x 10(-7) M and 5.0 x 10(-4)M was found. The detection limit was 1.0 x 10(-7) M. Recoveries were 93.2-108.7%. Influencing factors were investigated in detail and optimized.     

Competitive amperometric morphine sensor based on an agarose immobilised molecularly imprinted polymer

A morphine-sensitive device was constructed based on a molecularly imprinted polymer. The imprinted polymer exhibited recognition properties previously. A method of detection based on competitive binding was used to measure morphine in the concentration range 0.1–10 μg/ml. A morphine concentration of 0.5 μg/ml gave a peak current (by oxidation) of 4 nA. The method of morphine detection involves two steps. In the first step, morphine binds selectively to the molecularly imprinted polymer in the sensor. In the second step, an electroinactive competitor (codeine) is added in excess, whence some of the bound morphine is released. The released morphine is detected by an amperometric method. The advantages of this type of sensor compared to biosensors based on antibodies, enzymes or cells are discussed. This sensor, based on an artificial recognition system, demonstrates autoclave compatibility, long-time stability and resistance to harsh chemical environments.     

Flow chemiluminescence sensor for determination of clenbuterol based on molecularly imprinted polymer

In this paper, a novel flow chemiluminescence (CL) clenbuterol sensor based on molecularly imprinted polymer (MIP) on line enrichment nanogram clenbuterol and chemiluminescence reaction of potassium permanganate and formaldehyde in the polyphosphate enhanced by clenbuterol. Clenbuterol in the urine was selectively adsorbed on the clenbuterol-imprinted polymer, which was packed into the flow cell. The formaldehyde and the polyphosphate with potassium permanganate flowed through the flow cell and reacted with the on line adsorbed clenbuterol and produced strong CL. The results show that the sensor was reversible. The CL intensity was linear with clenbuterol concentration from 1.0 × 10⁻⁹ g/mL to 5.0 × 10⁻⁸ g/mL. The detection limit was 3.0 × 10⁻¹⁰ g/mL. The R.S.D. for ng/mL clenbuterol was less than 5% (n = 3). The present method offered a high selectivity and sensitivity that made the quantitative analysis of trace clenbuterol (ng/mL) in the animal urine sample.     

Polymer coated sensor array based on quartz crystal microbalance for chemical agent analysis

Quartz crystal microbalance (QCM) gas sensors based on polymeric material were fabricated and their gas response characteristics were examined for four simulant gases of chemical agents, which were dimethyl methyl phosphonate (DMMP), N,N-dimethylacetamide (DMA), 1,5-dichloropentane (DCP) and dichloroethane (DCE). For the selection of appropriate coating materials, both principal component analysis (PCA) and hierarchical cluster methods were applied to a data set collected from 15 QCM sensors for 12 analytes. Four appropriate coating materials were selected after optimizing the correlation between the 15 coating materials and the first four principal component (PC) factors. The four chosen polymers were used as sensitive component for a sensor array, and then PCA is adapted to classify four simulant gases. The results show that the QCM sensor array has high sensitivity and selectivity to four chemical agents.