器件参数对GaN基n~+-GaN/i-Al_x Ga_(1-x)N/n~+-GaN结构紫外和红外双色探测器中紫外响应的影响

研究了AlGaN层参数对GaN基n+-GaN/i-AlxGa1-xN/n+-GaN结构紫外和红外双色探测器中紫外响应的影响规律及物理机制.模拟计算发现:降低AlGaN层本底载流子浓度会增加器件的量子效率,当本底载流子浓度不能进一步降低时,可以通过减小AlGaN层的厚度以保证器件的量子效率.在材料生长和器件工艺过程中都应减少界面态.外加较小的反向偏压能大幅度提高紫外量子效率,分析表明,GaN/AlGaN/GaN形成的两个背靠背、方向相反的异质结电场是出现这些现象的根本原因.在实际器件设计中,应该根据需要调节各结构参数,以保证器件的量子效率.     

背势垒层结构对AlGaN/GaN双异质结载流子分布特性的影响

首先通过一维自洽求解薛定谔/泊松方程,研究了AlGaN/GaN双异质结构中AlGaN背势垒层Al组分和厚度对载流子分布特性的影响.其次利用低压MOCVD方法在蓝宝石衬底上生长出具有不同背势垒层的AlGaN/GaN双异质结构材料,通过汞探针CV测试验证了理论计算的正确性.理论计算和实验结果均表明,随着背势垒层Al组分的提高和厚度的增加,主沟道中的二维电子气面密度逐渐减小,寄生沟道的二维电子气密度逐渐增加;背势垒层Al组分的提高和厚度的增加能有效的增强主沟道的二维电子气限域性,但是却带来了较高的 关键词： AlGaN/GaN 双异质结构 限域性 寄生沟道     

Ⅲ族氮化物异质结构二维电子气研究进展

本文总结了近年来Ⅲ族氮化物半导体异质结构二维电子气的研究进展。从Ⅲ族氮化物材料晶格结构和特有的极化性质出发,重点讨论了AlGaN/GaN异质结构中二维电子气的性质,总结分析了异质结构中Al组分、势垒层厚度、应变弛豫度、掺杂等对二维电子气浓度和迁移率的影响,同时还涉及AlGaN/GaN/AlGaN,AlGaN/AlN/GaN和AlGaN/InGaN/GaN等异质结构二维电子气性质。     

Ⅲ族氮化物异质结构二维电子气研究进展

本文总结了近年来Ⅲ族氮化物半导体异质结构二维电子气的研究进展。从Ⅲ族氮化物材料晶格结构和特有的极化性质出发,重点讨论了AlGaN/GaN异质结构中二维电子气的性质,总结分析了异质结构中Al组分、势垒层厚度、应变弛豫度、掺杂等对二维电子气浓度和迁移率的影响,同时还涉及AlGaN/GaN/AlGaN,AlGaN/AlN/GaN和AlGaN/InGaN/GaN等异质结构二维电子气性质。     

p型GaN/Al0.35Ga0.65N/GaN应变量子阱中二维空穴气的研究

对Ga面p型GaN/Al0.35Ga0.65N/GaN应变异质结构中形成的二维空穴气(2DHG)进行了研究.首先基于半导体-绝缘体-半导体异质结构模型确定了应变异质中的临界厚度,然后自洽求解薛定谔方程和泊松方程,计算了当中间势垒层AlGaN处于完全应变状态和半应变状态两种条件下,顶层GaN及中间层AlGaN厚度的变化对2DHG分布的影响.计算结果表明,势垒层AlGaN和顶层GaN的应变状态和厚度对极化引起的2DHG面密度及分布有重要影响.在此基础上制备了p型GaN/Al0.35 Ga0.65N/GaN应变量子阱结构肖特基器件,并通过器件的C-V测试证实了异质结处2DHG的存在.器件响应光谱的测试结果表明,由于p型GaN/Al0.35Ga0.65N/GaN量子阱中强烈的极化作用和Stark效应使得器件零偏压和反向偏压时的响应光谱都向短波方向移动了10 nm,在零偏压下器件在280 nm处的峰值响应为0.022 A/W,在反向偏压为1 V时,峰值响应达到0.19 A/W,已经接近理论值.     

p型GaN/Al0.35Ga0.65N/GaN应变量子阱中二维空穴气的研究

对Ga面p型GaN/Al_0.35Ga_0.65N/GaN应变异质结构中形成的二维空穴气(2DHG)进行了研究.首先基于半导体-绝缘体-半导体异质结构模型确定了应变异质中的临界厚度，然后自洽求解薛定谔方程和泊松方程，计算了当中间势垒层AlGaN处于完全应变状态和半应变状态两种条件下，顶层GaN及中间层AlGaN厚度的变化对2DHG分布的影响.计算结果表明，势垒层AlGaN和顶层GaN的应变状态和厚度对极化引起的2DHG面密度及分布有重要影响.在此基础上制备了p型GaN/Al_0.35Ga_0.65N/GaN应变量子阱结构肖特基器件，并通过器件的C-V测试证实了异质结处2DHG的存在.器件响应光谱的测试结果表明，由于p型GaN/Al_0.35Ga_0.65N/GaN量子阱中强烈的极化作用和Stark效应使得器件零偏压和反向偏压时的响应光谱都向短波方向移动了10 nm，在零偏压下器件在280 nm处的峰值响应为0.022 A/W，在反向偏压为1 V时，峰值响应达到0.19 A/W，已经接近理论值. 关键词： AlGaN 二维空穴气 极化效应     

一种新型GaN基肖特基结构紫外探测器

提出了一种新型GaN基肖特基结构紫外探测器.该结构在常规的GaN肖特基结构紫外探测器上外加了一层禁带宽度更大的n型AlGaN层，模拟计算结果表明：与常规器件结构相比，该结构能有效地减小表面复合的影响，提高了器件的量子效率.进一步地研究结果还表明：采取较薄、载流子浓度较高的AlGaN层更有利于提高这种新结构器件的量子效率. 关键词： GaN 肖特基结构 紫外探测器 AlGaN     

近紫外380nm发光二极管的量子阱结构优化

模拟分析了有源区不同垒层对380 nm近紫外发光二极管的内量子效率、电子空穴浓度分布、辐射复合效率等产生的影响。有源区垒层材料分别选用GaN、Al0.1Ga0.9N、Al0.1Ga0.9N/Al0.15Ga0.85N/Al0.1Ga0.9N,其中3层AlGaN的厚度比分别为6 nm/8 nm/6 nm和7 nm/6 nm/7 nm。对比分析发现,与GaN垒层相比,选用AlGaN系列垒层可以将更多的载流子限制在有源区内,空穴浓度可以提高近一个数量级,辐射复合效率可以提高2～10倍;3层AlGaN垒层相对于单一AlGaN垒层,载流子分布更加均匀,辐射复合效率可以提高7倍以上,内量子效率可以提高14.5%;采用不同厚度比的3层AlGaN垒层结构可以微调能带的倾斜程度,进一步减小极化效应。可以调节合适的厚度比减小极化效应对于载流子分布及内量子效率的影响。     

具有部分本征GaN帽层新型AlGaN/GaN高电子迁移率晶体管特性分析

为了优化传统Al GaN/GaN高电子迁移率晶体管(high electron mobility transistors,HEMTs)器件的表面电场,提高击穿电压,本文提出了一种具有部分本征GaN帽层的新型Al GaN/GaN HEMTs器件结构.新型结构通过在Al GaN势垒层顶部、栅电极到漏电极的漂移区之间引入部分本征GaN帽层,由于本征GaN帽层和Al GaN势垒层界面处的极化效应,降低了沟道二维电子气(two dimensional electron gas,2DEG)的浓度,形成了栅边缘低浓度2DEG区域,使得沟道2DEG浓度分区,由均匀分布变为阶梯分布.通过调制沟道2DEG的浓度分布,从而调制了Al GaN/GaN HEMTs器件的表面电场.利用电场调制效应,产生了新的电场峰,且有效降低了栅边缘的高峰电场,Al GaN/GaN HEMTs器件的表面电场分布更加均匀.利用ISE-TCAD软件仿真分析得出:通过设计一定厚度和长度的本征GaN帽层,Al GaN/GaN HEMTs器件的击穿电压从传统结构的427 V提高到新型结构的960 V.由于沟道2DEG浓度减小,沟道电阻增加,使得新型Al GaN/GaN HEMTs器件的最大输出电流减小了9.2%,截止频率几乎保持不变,而最大振荡频率提高了12%.     

电容-电压法研究AlxGa1-xN/GaN异质结压电极化效应

制备了基于调制掺杂Al0.22Ga0.78N/GaN异质结的Pt/Al0.22Ga0.78N/GaN肖特基二极管.由于Al0.22Ga0.78N势垒层中的极化场不同,不同Al0.22Ga0.78N势垒层厚度的二极管的电容-电压特性显著不同.根据对样品电容-电压特性的数值模拟,在Al0.22Ga0.78N势垒层厚度为30nm和45nm的样品中,异质界面的极化电荷面密度为6.78×1012cm-2.在Al0.22Ga0.78N势垒层厚度为75nm的样品中,极化电荷面密度降为1.30×1012cm-2.这种极化电荷面密度的降低是由于GaN上Al0.22Ga0.78N势垒层由于厚度增加而产生应变的部分弛豫.本工作也提供了一种定量表征AlxGa1-xN/GaN异质结中极化电荷面密度的方法.     

Dual-band pixelless upconversion imaging devices

We have proposed a type of mid-infrared (MIR) and far-infrared (FIR) dual-band imaging device, which employs the photon frequency upconversion concept in a GaN/AlGaN MIR and FIR dual-band detector integrated with a GaN/AlGaN violet light emitting diode. On the basis of the photoresponse of single-period GaN/AlGaN dual-band detectors, we present the detailed optimization of multiperiod GaN emitter/AlGaN barrier detectors and their applications to dual-band pixelless upconversion imaging. Satisfying images have been received through the analysis of the modulation transfer function and the upconversion efficiency in the GaN/AlGaN dual-band pixelless upconverters, which exhibit good image resolution, high quantum efficiency, and negligible cross talk.     

Quantum structures for multiband photon detection

The work describes multiband photon detectors based on semiconductor micro-and nano-structures. The devices considered include quantum dot, homojunction, and heterojunction structures. In the quantum dot structures, transitions are from one state to another, while free carrier absorption and internal photoemission play the dominant role in homo or heterojunction detectors. Quantum dots-in-a-well (DWELL) detectors can tailor the response wavelength by varying the size of the well. A tunnelling quantum dot infrared photodetector (T-QDIP) could operate at room temperature by blocking the dark current except in the case of resonance. Photoexcited carriers are selectively collected from InGaAs quantum dots by resonant tunnelling, while the dark current is blocked by AlGaAs/InGaAs tunnelling barriers placed in the structure. A two-colour infrared detector with photoresponse peaks at ∼6 and ∼17 μm at room temperature will be discussed. A homojunction or heterojunction interfacial workfunction internal photoemission (HIWIP or HEIWIP) infrared detector, formed by a doped emitter layer, and an intrinsic layer acting as the barrier followed by another highly doped contact layer, can detect near infrared (NIR) photons due to interband transitions and mid/far infrared (MIR/FIR) radiation due to intraband transitions. The threshold wavelength of the interband response depends on the band gap of the barrier material, and the MIR/FIR response due to intraband transitions can be tailored by adjusting the band offset between the emitter and the barrier. GaAs/AlGaAs will provide NIR and MIR/FIR dual band response, and with GaN/AlGaN structures the detection capability can be extended into the ultraviolet region. These detectors are useful in numerous applications such as environmental monitoring, medical diagnosis, battlefield-imaging, space astronomy applications, mine detection, and remote-sensing. The paper presented there appears in Infrared Photoelectronics, edited by Antoni Rogalski, Eustace L. Dereniak, Fiodor F. Sizov, Proc. SPIE Vol. 5957, 59570W (2005).     

N极性GaN/AlGaN异质结二维电子气模拟

通过自洽求解薛定谔方程和泊松方程,较系统地研究了GaN沟道层、AlGaN背势垒层、Si掺杂和AlN插入层对N极性GaN/AlGaN异质结中二维电子气(2DEG)的影响,分析表明,GaN沟道层厚度、AlGaN背势垒层厚度及Al组分变大都能一定程度上提高二维电子气面密度,AlGaN背势垒层的厚度和Al组分变大也可提高二维电子气限阈性,且不同的Si掺杂形式对二维电子气的影响也有差异,而AlN插入层在提高器件二维电子气面密度、限阈性等方面表现都较为突出,在模拟中GaN沟道层厚度小于5nm时无法形成二维电子气,超过20nm后二维电子气面密度趋于饱和,而AlGaN背势垒厚度超过40nm后二维电子气也有饱和趋势,对均匀掺杂和delta掺杂而言AlGaN背势垒层Si掺杂浓度超过5×10~(19)cm~(-3)后2DEG面密度开始饱和,而厚度为2nmAlN插入层的引入会使2DEG面密度从无AlN插入层时的0.93×10~(13)cm~(-2)提高到1.17×10~(13)cm~(-2)。     

Performance Improvement of GaN-Based Violet Laser Diodes

The influences of InGaN/GaN multiple quantum wells(MQWs) and AlGaN electron-blocking layers(EBL) on the performance of GaN-based violet laser diodes are investigated. Compared with the InGaN/GaN MQWs grown at two different temperatures, the same-temperature growth of InGaN well and GaN barrier layers has a positive effect on the threshold current and slope efficiency of laser diodes, indicating that the quality of MQWs is improved. In addition, the performance of GaN laser diodes could be further improved by increasing Al content in the AlGaN EBL due to the fact that the electron leakage current could be reduced by properly increasing the barrier height of AlGaN EBL. The violet laser diode with a peak output power of 20 W is obtained.     

Polarization effects simulation of AlGaN/GaN heterojunction by using a symbolistic δ-doping layer

Polarization effects in AlGaN/GaN heterojunction are simulated based on a traditional semiconductor device simulator. A δ doping layer is purposely inserted at the interface of the heterojunction in the simulation, so the ionized donors or acceptors can represent polarization-induced positive or negative fixed charges. The free electron distribution of single AlGaN/GaN heterostructures with Ga-face and N-face growth is compared, and the results of the simulation show that carrier confinement takes place only in the former structure. The dependence of sheet density of free electrons at the interface of Ga-face growth AlGaN/GaN on Al composition and the thickness of AlGaN is also investigated. The consistency of simulation results with the experiments and calculations reported by other researchers shows that this method can be effectively used to deal with the polarization effects in the simulation of GaN-based heterojunction devices.     

The low-temperature mobility of two-dimensional electron gas in AlGaN/GaN heterostructures

To reveal the internal physics of the low-temperature mobility of two-dimensional electron gas （2DEG） in Al- GaN/GaN heterostructures, we present a theoretical study of the strong dependence of 2DEG mobility on Al content and thickness of AlGaN barrier layer. The theoretical results are compared with one of the highest measured of 2DEG mobility reported for AlGaN/GaN heterostructures. The 2DEG mobility is modelled as a combined effect of the scat- tering mechanisms including acoustic deformation-potential, piezoelectric, ionized background donor, surface donor, dislocation, alloy disorder and interface roughness scattering. The analyses of the individual scattering processes show that the dominant scattering mechanisms are the alloy disorder scattering and the interface roughness scattering at low temperatures. The variation of 2DEG mobility with the barrier layer parameters results mainly from the change of 2DEG density and distribution. It is suggested that in AlGaN/GaN samples with a high Al content or a thick AlGaN layer, the interface roughness scattering may restrict the 2DEG mobility significantly, for the AlGaN/GaN interface roughness increases due to the stress accumulation in AlGaN layer.     

Two-dimensional electron gas densities in AlGaN/AlN/GaN heterostructures

The dependence of two-dimensional electron gas (2DEG) density and distribution in an Al_xGa_1-xN/AlN/GaN heterostructure on the thicknesses of the Al_xGa_1-xN barrier layer and the AlN interfacial layer are investigated theoretically. A competitive contribution of the AlGaN and AlN layers to the 2DEG density is revealed. For an AlN interfacial layer thinner than a critical value d_cAlN, the 2DEG density is dominated by the AlGaN barrier and the 2DEG density increases with the increase of the AlGaN barrier thickness, as in the case of a simple AlGaN/GaN heterostructure. While the AlN interfacial layer will take the dominant contribution to the 2DEG density as its thickness exceeds d_cAlN. In this case, the increase of AlGaN barrier layer thickness leads to the decrease of the 2DEG density. Detailed calculations show that the critical AlN thickness increases with the increase of Al content in the AlGaN barrier. PACS 85.30.De; 73.40.Kp; 02.60.Cb     

Simulation of polarization effects in AlGaN/GaN heterojunction

Because of their large band-gap, large high-field electron velocity, large breakdownfield, and large thermal conductivity, GaN and its heterojunction with AlGaN and InGaNhave foreseeable potential in the applications of high-power/temperature electronics, andoptoelectronic devices operative in UV and visible wavelength. Polarization inducedelectric field can reach the magnitude of ~MV/cm[1,2]. For AlGaN/GaN based FETs theconcentration of sheet carrier induced by polarization in the cha…     

Impact of AlxGa1-xN barrier thickness and Al composition on electrical properties of ferroelectric HfZrO/Al2O3/AlGaN/GaN MFSHEMTs

Ferroelectric (FE) HfZrO/Al$_{2}$O$_{3}$ gate stack AlGaN/GaN metal-FE-semiconductor heterostructure high-electron mobility transistors (MFSHEMTs) with varying Al$_{x}$Ga$_{1-x}$N barrier thickness and Al composition are investigated and compared by TCAD simulation with non-FE HfO$_{2}$/Al$_{2}$O$_{3}$ gate stack metal-insulator-semiconductor heterostructure high-electron mobility transistors (MISHEMTs). Results show that the decrease of the two-dimensional electron gas (2DEG) density with decreasing AlGaN barrier thickness is more effectively suppressed in MFSHEMTs than that in MISHEMTs due to the enhanced FE polarization switching efficiency. The electrical characteristics of MFSHEMTs, including transconductance, subthreshold swing, and on-state current, effectively improve with decreasing AlGaN thickness in MFSHEMTs. High Al composition in AlGaN barrier layers that are under 3-nm thickness plays a great role in enhancing the 2DEG density and FE polarization in MFSHEMTs, improving the transconductance and the on-state current. The subthreshold swing and threshold voltage can be reduced by decreasing the AlGaN thickness and Al composition in MFSHEMTs, affording favorable conditions for further enhancing the device.