Redox-driven transport of copper ions in an emulsion liquid membrane system

A new redox-driven type of emulsion liquid membrane separation is described. Milligram amounts of copper(II) in 0.2 M hydrochloric acid were reduced to copper(I) in the presence of ascorbic acid (1 M≡1 mol l⁻¹). The copper solution was emulsified with a (1+4) mixture of toluene and n-heptane using Span-80 (sorbitan monooleate) as an emusifier. The resulting water-in-oil emulsion was dispersed in 0.2 M hydrochloric acid containing hydrogen peroxide and neocuproine (2,9-dimethyl-1,10-phenanthroline) by stirring for 10 min. The copper in the internal aqueous phase was selectively transported to the external one, leaving other heavy metals (e.g., Mn, Co, Ni, Cd and Pb) in the internal aqueous phase. After collecting the dispersed emulsion globules, they were demulsified by heating and the metals in the segregated aqueous phase were determined by graphite-furnace atomic absorption spectrometry (GFAAS). The selective transport of copper offered the multielement separation of trace heavy metals from a copper matrix, allowing the GFAAS determination of impurities at the 0.01% level in copper metal.     

Enhancement of oxygen gas–liquid mass transfer with colloidal gas aphron dispersions

In this work, an attempt was made to enhance gas–liquid mass transfer of oxygen with the aid of colloidal gas aphron (CGA) dispersion. The gas–liquid volume mass transfer coefficients (k_La) of oxygen in CGA dispersions were measured and related to stirring velocity, type and concentration of surfactants, and temperature. Four surfactants, sodium dodecyl sulfate (SDS), hexadecyltrimethyl ammonium chloride (HTAC), nonylphenol ethoxylate (NP-10), and potassium mono lauryl phosphate (MAPK), were examined in forming CGAs and thereby affecting the mass transfer of oxygen in the dispersions. It was found that effects of surfactants on the oxygen gas–liquid mass transfer were type-dependent. As concentrations rose, the k_La of oxygen increased evidently for SDS and an enhancement of k_La by a factor of three was observed at the concentration of 2.75 g/L. However the k_La decreased for MAPK. Nonylphenol ethoxylate was found to have little effect on k_La and HTAC showed mixed behavior. In SDS dispersion, it was found that the mass transfer reached a maximum value at a stirring velocity of 8000 r/min, but further benefit was not observed afterwards. With the increase of temperature, the mass transfer of oxygen was intensified but no much benefit was observed above 308 K.     

Mathematical modeling of silver extraction by an emulsion liquid membrane process

A general physical model of a typical batch extraction system employing an emulsion liquid membrane process for the extraction of silver has been developed. The model takes into account the extraction reaction between the silver ion and the carrier molecules at the external interface, the diffusion of the complex in the membrane phase, the stripping reaction at the internal interface and the reaction of silver ion with the reagent, HCL, in the internal phase to yield silver chloride incapable of permeating through the membrane phase. In addition, the leakage of the internal aqueous phase to the external aqueous phase due to membrane breakage has been incorporated in this model. The batch extraction of silver using D2EHPA as a carrier has been carried out under various experimental conditions. The experimental data can be well explained by the present model.     

正十六胺为载体的乳状液膜迁移分离汞(Ⅱ)

以正十六胺为载体的乳状液膜迁移分离汞 的结果表明,当膜组成为(0 02～0 030)ｍｏｌ/Ｌ正十六胺+3%(Ｗ/Ｖ)Ｓｐａｎ80+煤油;内相为(0 010～0 020)ｍｏｌ/ＬＮａＯＨ;外相为0 020ｍｏｌ/ＬＫＣＬ+(0 010～0 10)ｍｏｌ/ＬＨＣｌ能使汞快速有效的完全迁移;并使Ｈｇ 与Ｃｕ ,Ｆｅ ,Ｚｎ ,Ｃｏ ,Ｎｉ ,Ｍｎ ,Ｐｂ ,Ｃｄ 等离子完全分离。不使用有毒害的膜溶剂甲秦或二甲苯[1-4],使用长碳链的有机胺,因而在相分离过程中避免了三相乳化现象。1.实验部分在制乳器中加入一定量Ｓｐａｎ80和正十六胺的煤油溶液,在约2000ｒ/ｍｉｎ转速下,加入内相试剂…     

铜在乳状液膜体系中的迁移行为

近年来膜分离技术在环境治理方面得到广泛应用。本文研究了铜在span80-TBP（磷酸三丁酯）-煤油-NH3液膜分离体系中的迁移行为。用TBP作为载体,在溶液中迁移时,在外相与膜相界面上形成中性络合物后穿过膜相,在膜相与内相界面上络合物再与NH3反应,生成铜氨络离子,释放出来的TBP又返回膜相。     

Field and photo-field electron emission from self-assembled Ge–Si nanostructures with quantum dots

Monolayer and multilayer Ge nanocluster structures were prepared on Si(1 0 0) using molecular beam epitaxy. The cluster size was 10 nm and cluster density was 10¹⁰ cm⁻². A stable field electron emission was obtained from these structures, showing current peaks in the current–voltage characteristics, which may be attributed to the resonant electron tunneling via the energy levels of the nanocluster potential well. For cluster multilayers, the current–voltage curves also showed current peaks with a complex shape. The cluster multilayer structures had a considerable temperature sensitivity, as well as photosensitivity, in the wavelength range from 0.4 to 10 μm.     

Synchronized extraction and purification of L-lactic acid from fermentation broth by emulsion liquid membrane technique

This study aims to investigate the recovery of L-lactic acid from fermentation broth by an emulsion liquid membrane (ELM), made up of sunflower oil as the diluent, Sorbitan monooleate (Span 80) as the surfactant, Aliquat 336 as the carrier, and sodium hydroxide (NaOH) solution as the internal aqueous phase. Particularly, the ELM process was properly set up, through the identification of the optimal ELM operating parameters on the final extraction efficiency of L-lactic acid, including Span 80 concentration, NaOH concentration, Aliquat 336 concentration, stirring speed, phase ratio, and treatment ratio. The obtained results showed that the extraction efficiency of L-lactic acid reached up to 99% under the following optimal conditions: 10 minutes after contact time, 4% w/w Span 80, 3% w/w Aliquat 336, 0.1?N solution of NaOH, stirring speed of 300?rpm, phase ratio 1, and treatment ratio 0.25. A stable system without considerable emulsion swelling and breakage was monitored using a dynamic light scattering (DLS) apparatus for the selected optimal ELM operating parameters.     

Extraction and carrier mediated transport of urea using noncyclic receptors through liquid membrane systems

Extraction and carrier mediated transport through bulk liquid membrane and supported liquid membrane systems have wide applications in separation technology. This paper highlights the use of six noncyclic receptors (podands) having variations in chain length and end group for the removal of urea using liquid membrane system. These receptors R_1, R_2, R_3, R_4, R_5, R₆ are diethylene glycol dimethyl ether, diethylene glycol dibutyl ether, diethylene glycol dibenzoate, diethylene glycol, triethylene glycol and tetraethylene glycol respectively. The sequence of extraction and transport of urea by BLM system using various receptors is R₂ > R₃ > R₁ > R₄ > R₅ > R₆ and R₆ ≈ R₃ > R₅ > R₄ > R₁ > R₂ respectively. Receptor R₂ containing butyl end group is best extractant while receptor R₆ with flexible backbone is best carrier and this carrier efficiency is used to remove urea using BLM system from the feed phase by recyclization process up to 88.16%. The experimental results influenced by concentration of receptors and urea. Effect of time was also studied.     

Efficient transport of saccharides through a liquid membrane mediated by a cyclodextrin dimer

A new efficient system for transporting saccharides through a liquid membrane has been constructed. The transport rates of saccharides were accelerated greatly by the cyclodextrin dimer 2; by contrast, the corresponding cyclodextrin monomer 1 was not effective at mediating saccharide transport. The transport rate of D-ribose through a chloroform liquid membrane was 17 times faster when the cyclodextrin dimer 2 was used as the transporter than when the cyclodextrin monomer 1 was used. Similarly the transport rate of methyl D-galactopyranoside was 16 times faster by 2 than by 1.     

Coupled transport of Ag(I) ions through triethanolamine–cyclohexanone-based supported liquid membranes

Facilitated transport of silver(I) ions in acidic medium, across a supported liquid membrane (SLM) by using triethanolamine (TEA) as carrier, dissolved in cyclohexanone, has been investigated. The parameters studied are HNO₃ concentration variation in the feed, pH of the feed solution, carrier concentration in the membrane phase, silver(I) ions concentration in the feed phase and KCN concentration in the stripping phase. Increase in H⁺ concentration by increasing HNO₃ concentration from 0.5 to 1 M results into an increase in silver ions flux but a decrease in flux has been found beyond 1 M HNO₃ concentration in the feed, providing a maximum flux of 3.21 × 10⁻⁷ mol/m² s at 1 M HNO₃. Increase in TEA concentration inside the membrane enhances flux with its maximum value at 2.25 M TEA. Further increase in the concentration of TEA leads to a decreased rate of transport due to the increase in viscosity of membrane liquid. The optimum conditions for Ag(I) ions transport are 1 M HNO₃ (feed), 2.25 M TEA (membrane) and 1.5 M KCN in the stripping phase. It has been observed that Ag(I) flux across the membrane tends to increase with increase in Ag(I) ions concentration in the feed phase. Applying the studied conditions to silver plating waste solutions, Ag ions have been removed up to 99% in a time interval of 5 h.     

Solid-state chemiluminescence assay for ultrasensitive detection of antimony using on-vial immobilization of CdSe quantum dots combined with liquid–liquid–liquid microextraction

On-vial immobilized CdSe quantum dots (QDs) are applied for the first time as chemiluminescent probes for the detection of trace metal ions. Among 17 metal ions tested, inhibition of the chemiluminescence when CdSe QDs are oxidized by H₂O₂ was observed for Sb, Se and Cu. Liquid–liquid–liquid microextraction was implemented in order to improve the selectivity and sensitivity of the chemiluminescent assay.     

Liquid–gas–liquid technique for microextraction and preconcentration of short chain fatty acids from aqueous samples

In this study, an organic solvent‐free microextraction technique termed liquid–gas–liquid microextraction (LGLME) was applied for cleanup and preconcentration of volatile short chain fatty acids in beverages and dairy products. Various parameters affecting the extraction efficiency such as extraction time, stirring speed, sodium chloride content, concentration and volume of donor and acceptor phases, and extraction temperature were studied. Repeatability (RSD, 4.2–8.5%), correlation coefficients (0.998–0.999), LODs (10–20 μg/L) and enrichment factors (152–249) were also investigated. Recoveries were achieved in the range of 90–102% in different matrices. The presented method was applied for the analysis of target analytes in some samples such as grape juice, vinegar and dairy products.     

Transport of calcium and potassium ions in opposite directions in a liquid membrane system

A new type of 18-crown-6 derivative having two carboxylic acids on the side arms transported calcium and potassium ions in opposite directions across a dichloromethane membrane by pH control. Calcium and potassium ions were concentrated in the acidic and the basic phases, respectively. The presence of picrate ion in the acidic phase plays an important role in the transport of potassium ion from the acidic to the basic phase.     

Highly selective transport of silver ion through a supported liquid membrane using calix[4]pyrroles as suitable ion carriers

Facilitated transport of silver ion across a supported liquid membrane (SLM) by calix[4]pyrroles, as selective ion carriers, dissolved in kerosene has been investigated. The influences of fundamental parameters affecting the transport of silver ion including ion carrier concentration in the membrane phase, thiosulfate concentration in strip phase, picric acid concentration in the feed phase, stirring speed of aqueous phases, type of membrane solvent and time of transport have been studied. In the presence of thiosulfate as a suitable metal ion acceptor in the strip phase and picrate ion as ion pairing agent in the source phase, transport of silver occurs almost quantitatively after 75 min. The selectivity and efficiency of silver transport from aqueous solution containing Cu²⁺, Mg²⁺, Ni²⁺, Ca²⁺, Zn²⁺, Pb²⁺, Co²⁺, Al³⁺, Hg²⁺, Cd²⁺, Fe³⁺, Fe²⁺ and Cr³⁺ were investigated.     

Hydrothermal synthesis of highly luminescent CdTe quantum dots by adjusting precursors’ concentration and their conjunction with BSA as biological fluorescent probes

A study on hydrothermal synthesis of CdTe quantum dots, highly luminescent nanocrystals at a relatively lower temperature, via changing the concentration of the CdTe precursors, is described. The full width at half maximum ranged from 40 to 80 nm and quantum yield (QY) was detected to be 27.4% at room temperature. The as-prepared CdTe QDs were labeled with BSA for fluorescence probes without pretreatment. Conjunction experimental results suggested that the as-prepared CdTe QDs are suitable for the application of biotechnology.     

Synergetic transport of europium through a contained supported liquid membrane using trioctylamine and tributyl phosphate as carriers

Contained supported liquid membrane (CSLM) system has been explored for synergic liquid membranes. Different experimental variables such as concentration of acid, carrier, metal ion and complexing agents, stirring speed, etc. have been investigated. Trioctylamine (TOA) + tributyl phosphate (TBP) system has been explored for europium.     

Liquid membrane transport of supramolecular complexes of some amines and amino acids with macrocyclic ligands

The transport of some amines in protonated form was studied (viz. methylamine, dimethylamine, diethylamine andn-propylamine) and -amino acids (l-leucine,l-methionine,l-isoleucine,l-phenylalanine,l-valine,l--alanine andl-cysteine). The following macrocyclic ligands were used as carriers throughout the experiments: 15-crown-5 (15C5), 18-crown-6 (18C6), benzo-18-crown-6 (B18C6), dibenzo-18-crown-6 (DB18C6), diazacrown ether [2.2] (1,7,10,16-tetraoxa-4,13-diazacyclooctadecane) and cryptand [2.2.2] (4,7,13,16,21,24-hexaoxa-1,10-diazabicyclo [8.8.8] hexacosane). The active transport, assisted by pH gradient, of amino acids and amines in protonated form as ion pairs in the presence of picrate anion was performed. The experiments suggested the influence of the ligand size, the donor atom type, and the substituents on the transport phenomena.     

Facilitated transport of copper(II) across supported liquid membrane and polymeric plasticized membrane containing 3-phenyl-4-benzoylisoxazol-5-one as carrier

The potential of 3-phenyl-4-benzoylisoxazol-5-one (HPBI) as metal extractant has been evaluated for the first time for Cu(II) transport from aqueous nitrate solutions by supported liquid membrane (SLM) in the solvents chloroform, 2-nitro phenyl octyl ether (NPOE) and dodecyl nitro phenyl ether (DNPE). The efficiency of the membrane transport was optimized as a function of pH, temperature, aqueous phases and membrane composition. It follows the sequence CHCl₃ > DNPE > NPOE. The results suggested that the transport mechanism was mainly controlled by the diffusion of the Cu(PBI)₂ complex in the membrane core. A comparative investigation of Cu(II) transport ions has been made between SLM and polymeric plasticized membrane (PPM), containing HPBI with NPOE and DNPE as organic solvents or plasticizers in order to evaluate the feasibility of PPM with HPBI.     

Comparison of sulphur and sulphur–oxygen ligands as ionophores for liquid–liquid extraction and facilitated transport of silver and palladium

The reactivity of new ligands described as S₁, S₅, S₂O₉ (in respect to character and amount of donors) towards metal ions was examined by extraction from HNO₃ and HCl media. These ligands were next utilised as carriers for Ag and Pd transport through a supported liquid membrane (SLM). The effect of collecting a greater number of S donors in one molecule and the influence of type of donors (O–S versus S) on efficiency and selectivity of Ag and Pd(II) extraction and transport were examined.

The extraction of Ag from HNO₃ solutions increased with increasing amount of S-donors in one molecule (S₁2O₉5). For palladium the sequence was different (S₅12O₉). The transport of Ag through SLM impregnated with m-chlorotoluene solution of ionophore increased in the same order as in the case of extraction, whereas for Pd the row was different: S₅2O₉1. The highest fluxes of Ag and Pd transported from HNO₃ equalled to 5.25×10⁻⁷ and 1.37×10⁻⁷ mol/m² s, respectively. Palladium flux depended on stripping solution type (Na₂S₂O₃相似文献   

Investigation of multivalent interactions between conjugate of quantum dots with c‐Myc peptide tag and the anti‐c‐Myc antibody by capillary electrophoresis with fluorescence detection

Herein, we report an assay for detecting the binding of a multivalent peptide and antibody within a capillary with the use of fluorescence coupled capillary electrophoresis. Quantum dots and a c‐Myc tag containing peptide EQKLISEEDLG₄H₆ were injected sequentially and formed a multivalent quantum dot‐EQKLISEEDLG₄H₆ assembly within the capillary. The efficiency of the quantum dot‐peptide self‐assembly was affected by the peptide/quantum dot molar ratio, sampling time, and interval time. Finally, the binding of the monoclonal anti‐c‐Myc antibody and the multivalent quantum dot‐EQKLISEEDLG₄H₆ ligand was studied using an in‐capillary assay. The microscopic dissociation constant for the self‐assembly of monoclonal anti‐c‐Myc antibody and quantum dot‐EQKLISEEDLG₄H₆ was determined to be 14.1 μM with a stoichiometry of the peptide‐antibody complex of 1.7 determined after fitting this to the Hill equation. This method can be further extended to detect a wide range of biomolecule–biomolecule binding interactions.