Improvement of the light output and contact resistance of InGaN-based light-emitting diodes based on tantalum-doped indium tin oxide as p-type electrodes

This paper reports that highly transparent and low resistance tantalum-doped indium tin oxide (Ta-doped ITO) films contacted to p-type GaN have been prepared by the electron-beam evaporation technique. The Ta-doped ITO contacts become Ohmic with a specific contact resistance of $\sim 5.65\times 10^{ - 5}$~$\Omega \cdot$cm$^{2}$ and show the transmittance of $\sim $98% at a wavelength of 440~nm when annealed at 500~\du. Blue light emitting diodes (LEDs) fabricated with Ta-doped ITO p-type Ohmic contact layers give a forward-bias voltage of 3.21~V at an injection current of 20~mA. It further shows that the output power of LEDs with Ta-doped ITO contacts is enhanced 62% at 20~mA in comparison with that of LEDs with conventional Ni/Au contacts.     

Zero biased Ge-on-Si photodetector with a bandwidth of 4.72~GHz at 1550~nm

High quality Ge was epitaxially grown on Si using ultrahigh vacuum/chemical vapor deposition (UHV/CVD). This paper demonstrates efficient germanium-on-silicon p-i-n photodetectors with 0.8~μm Ge, with responsivities as high as 0.38 and 0.21~A/W at 1.31 and 1.55~μ m, respectively. The dark current density is 0.37~mA/cm² and 29.4~mA/cm² at 0~V and a reverse bias of 0.5~V. The detector with a diameter of 30~μ m, a 3~dB-bandwidth of 4.72~GHz at an incident wavelength of 1550~nm and zero external bias has been measured. At a reverse bias of 3~V, the bandwidth is 6.28~GHz.     

基于SOA和级联取样光纤光栅的多波长激光器

研究了基于半导体光放大器(SOA)和双段级联取样光纤光栅构成的新型结构多波长激光器.设 计了取样光纤光栅，计算了其反射谱，模拟了多波长激光器的输出光谱.基于自行制作的SOA 和取样光纤光栅，进行了多波长激光器的实验研究，得到了间隔为0.8nm、输出功率不平坦 度小于1.0dB的11个波长输出.理论和实验两个方面都可以验证：与基于普通取样光栅的多波 长方案相比，基于双段级联取样光栅的方案能改善输出谱平坦度，并可提高可激射波长数. 关键词： 半导体光放大器 取样光纤光栅 多波长激光器     

Continuous True-Time-Delay System Employing a Novel Tunable Chirped Fiber Grating Delay Line and a Sampled Grating Based Multiwavelength Fiber Laser

A photonics true-time-delay system for phased array antenna beam steering employing a novel tunable chirped fiber grating delay line and a multi-wavelength erbium-doped fiber ring laser source based on a sampled grating filter is proposed. The tunable chirped fiber grating, which act as a continuous time-delay element, is achieved by bending a uniform fiber Bragg grating bonded at a slant onto the lateral surface of a simply supported beam. This technique allows the dynamic control of the chirp rate and spectral width of the grating without center wavelength shift. By adjusting the chirp rate of the fiber grating via bend strain, this kind of tunable chirped fiber grating could achieve very low and adjustable delay times, therefore provides higher angle resolution for scanning microwave beam, even the wavelengths of laser source are fixed and un-tunable. The true-time-delay system using proposed tunable chirped fiber grating delay element and sampled grating based laser source is constructed and demonstrated experimentally.     

Design of surface emitting distributed feedback quantum cascade laser with single-lobe far-field pattern and high outcoupling efficiency

A 7.8-$\mu $m surface emitting second-order distributed feedback quantum cascade laser (DFB QCL) structure with metallized surface grating is studied. The modal property of this structure is described by utilizing coupled-mode theory where the coupling coefficients are derived from exact Floquet--Bloch solutions of infinite periodic structure. Based on this theory, the influence of waveguide structure and grating topography as well as device length on the laser performance is numerically investigated. The optimized surface emitting second-order DFB QCL structure design exhibits a high surface outcoupling efficiency of 22{\%} and a low threshold gain of 10~cm$^{ - 1}$. Using a {$\pi $} phase-shift in the centre of the grating, a high-quality single-lobe far-field radiation pattern is obtained.     

Time domain numerical model for linear and nonlinear grating assisted co-directional coupler

A time domain algorithm for the dynamic analysis of linear and nonlinear devices based on coupled modes propagating with different group velocities is presented for the first time. As a test case, the numerical algorithm is applied to the analysis of a linear grating assisted co-directional coupler, in order to investigate quantitatively its limitations. As an application example, we show the simulation results on the switching dynamics of a current injection controlled grating assisted co-directional coupler sampled Bragg reflectors laser.     

一种新颖的取样光纤光栅振幅版的研制

提出了一种新颖的用于制作取样光纤光栅的取样振幅版的设计方案，其特点是具有渐变的取样周期和不变的占空比，利用这种振幅版可以简单灵活地制作出反射峰波长间隔不同的取样光栅梳状滤波器，有利于提高取样光栅的制作灵活性并降低成本.对这种方法可能存在的不足也进行了分析.利用制作出的取样光栅，基于全光纤结构实现了具有游标尺式波长调谐机理的可选波长光纤激光器.     

一种新颖的取样光纤光栅振幅版的研制

提出了一种新颖的用于制作取样光纤光栅的取样振幅版的设计方案,其特点是具有渐变的取样周期和不变的占空比,利用这种振幅版可以简单灵活地制作出反射峰波长间隔不同的取样光栅梳状滤波器,有利于提高取样光栅的制作灵活性并降低成本.对这种方法可能存在的不足也进行了分析.利用制作出的取样光栅,基于全光纤结构实现了具有游标尺式波长调谐机理的可选波长光纤激光器. 关键词： 取样光纤光栅 梳状滤波器 可选波长光纤激光器 振幅版     

Wavelength-switchable erbium-doped fiber ring laser combined with a Fabry-Perot laser diode and a sampled grating

We present a wavelength-switchable erbium-doped fiber ring laser consisting of an anti-reflection coated Fabry-Perot laser diode (FP-LD) and a sampled fiber Bragg grating (SFBG). The wavelength switching is obtained easily by the shift of FP mode with respect to the reflection peaks of the SFBG. The proposed laser apparatus not only simultaneously emits two wavelengths but also switches between the two wavelengths by adjusting the modes of FP-LD with a change of the injection current of the FP-LD as little as ∼1 mA. The proposed wavelength-switchable erbium-doped fiber ring laser exhibits high laser performance with side-mode suppression ratio (SMSR) ?50 dB.     

A unidirectional room temperature multi-wavelength fiber ring laser without isolator

A simplified ring cavity for achieving a unidirectional room temperature multi-wavelength erbium-doped fiber ring laser without optical isolator is demonstrated. The fiber ring cavity is built in such a way that the optical fields propagating in two directions suffer different losses caused by one sampled fiber Bragg grating. Furthermore, simultaneous multi-wavelength lasing with 0.8-nm intervals is demonstrated with sinusoidal phase modulation just before the sampled fiber Bragg grating to prevent single-wavelength lasing and unstable wavelength oscillation.     

Sampled grating distributed feedback (SG DFB) semiconductor laser diode

A laser diode was designed using a method called sampled grating (SG) distributed feedback (DFB), in which the couplings have been distributed in certain regions along the laser cavity (i.e., regions contain grating). These regions play a big role in pushing the main mode to propagate faster than the side mode by increasing the time delay between them. This delay is due to the empty regions (i.e., regions without grating) along the laser cavity. Neither a phase shift nor incomplete grating have been taken into account with the new structure. The theoretical model in the present work is based on the coupled-mode equations which have been solved numerically by the mean of transfer matrix method (TMM).     

光栅外腔半导体激光器GHz射频调制特性研究

研究了光栅外腔半导体激光器(ECDL)对射频频率调制的响应特性,分析了射频频率调制时光栅外腔对半导体激光器的边带信号的影响.实验中测量了GHz射频频率调制的.ECDL输出的边带信号随射频信号功率、注入电流、光栅外腔长度的变化情况.证实了当射频调制频率等于光栅外腔自由光谱区的整数倍时,ECDL输出的边带信号可在一定程度上得到增强.     

Dual-wavelength external cavity laser with a sampled grating formed in a silica PLC waveguide for terahertz beat signal generation

We propose and demonstrate a dual-wavelength external cavity laser (ECL). In our design, a Fabry–Pérot laser diode (FP-LD) is hybrid-integrated with a sampled Bragg grating written in a silica planar lightwave circuit (PLC). The grating selects two laser wavelengths that share the same laser cavity. The dual-wavelength oscillation with a side mode suppression ratio >32 dB has been demonstrated experimentally. Experimental results indicate that the hybrid-integrated dual-wavelength ECL exhibits strong dual-wavelength emission corresponding to beat frequency of 1 THz. Simulations of this system also indicate good mutual coherence of the two modes and stability of the 1 THz beat signal. PACS 42.79.Dj; 42.60.By; 42.55.Px     

增益半导体光放大器的特性

为满足半导体光放大器（SOA）在光纤到户FTTH系统接入网中的广泛应用,提出了基于光纤光栅外腔反馈型GC-SOA结构的全光增益机制,窄线宽激光光源经可变衰减器、隔离器和光纤光栅注入到SOA中,SOA的输出光经隔离器和光纤光栅送至光谱分析仪,通过光纤光栅反馈输入SOA形成钳制激光。对GC-SOA的阈值特性、增益特性及开关特性进行分析,结果表明:当注入电流小于GC-SOA的阈值电流时,增益随注入电流的增加而增加;当注入电流大于GC-SOA的阈值电流后,其增益不再随注入电流的变化而变化,实现了SOA的增益稳定,使SOA的饱和输出功率得到了提高。     

Dynamic single-mode and modulation characteristics analyses for λ/4 phase-shifted distributed feedback lasers with chirped grating

The dynamic single-mode and modulation performance of λ/4 phase-shifted distributed feedback laser diode with chirped grating (QWS-CG-DFB) are analyzed theoretically. The numerical simulation shows that, in contrast to purely QWS-DFB laser, the enhanced dynamic single-mode suppression ratio (SMSR) can be reached by QWS-CG-DFB laser. Under the smaller biasing current, the modulation band-width in presence of chirped grating is narrower, this difference shrinks for larger biasing current. For large signal modulation, the chirped grating is helpful to increase the output extinction ratio, but worsens the frequency chirping. The good dynamic characteristic can be obtained by selecting system parameters reasonably.     

激光告警中近红外焦平面阵列探测器成像技术研究

为了提高激光探测的方位分辨率,实现对来袭激光的准确定位,选用了FPA-320x256-C型InGaAs焦平面阵列探测器作为光栅衍射型激光告警装置的核心元件。介绍了基于光栅衍射的激光波长和方向探测原理,在分析了探测器性能及参数的基础上设计了驱动电路。探测器在FPGA时序的控制下,输出模拟量通过高速AD进行采集,数据经缓存后存储在FPGA外扩的SRAM中,然后通过USB传送至PC机。上位机Labview采集原始数据,处理并显示。利用上述方法,完成了成像实验,采用波长为1 550和980 nm的激光器从不同角度进行入射,对探测得到的衍射图像进行分析,判断出零级和一级的位置,根据光栅衍射理论,计算出相应波长和二维方向入射角,结果显示波长误差小于10 nm,入射角误差小于1°。     

Stable and continuous wavelength tuning of a hybrid semiconductor laser with an erbium-doped fiber external cavity

We present an experimental study of tuning characteristics and wavelength stability of a 1490 nm doped fiber external cavity laser. The standing wave in the erbium-doped fiber in an external-cavity laser causes spatial hole burning and absorption modulation and forms a dynamic grating. The dynamic grating can effectively suppress side modes and eliminate wavelength fluctuations in the laser. The operating wavelength of this hybrid laser is shown for the first time to our knowledge to be smoothly tunable by changing the semiconductor laser drive current or temperature.     

基于光谱合束技术的透射光栅模拟设计

半导体激光器光谱合束技术能够实现近衍射极限的高功率激光输出,已成为当前研究热点。衍射光栅的性能直接决定光谱合束的激光输出效果。模拟设计了一种针对940 nm波长、熔融石英材料的亚波长透射光栅。基于严格耦合波理论对光栅结构进行初步设计,运用Rsoft软件依次对光栅占空比、脊高和周期等参数进行优化确定,同时分析了各个参数对光栅衍射效率的影响。所设计的透射式光栅实现第-1级衍射级次的波分复用功能,衍射效率达到91.2%(TE模式),同时压缩其他衍射级次,使其衍射效率降到1.2%以下。同时在光栅入射角度59°±3°范围内保持90%以上的衍射效率,实现高功率激光输出的同时具有较高的误差容错率,易于调节,满足光谱合束技术的要求。     

亚波长光栅调制的偏振稳定垂直腔面发射激光器研究

基于微光学技术设计得到了偏振稳定垂直腔面发射激光器结构, 将亚波长光栅结构集成在上分布布拉格反射镜表面, 光栅周期小于材料中光波长, 透射波和反射波中仅包含零级衍射, 避免了高级次衍射造成 的损耗. 集成光栅后不同偏振方向光阈值增益不同, 从而实现偏振控制. 实验结 果显示, 集成亚波长光栅结构后, 整个激射过程中偏振方向被固定在平行于光栅槽方向上, 获得偏振稳定激光输出, 正交偏振抑制比大于12 dB, 且阈值电流仅增大7.14%.     

Design of a single-mode directly modulated orbital angular momentum laser

We propose a design of single-mode orbital angular momentum(OAM) beam laser with high direct-modulation bandwidth. It is a microcylinder/microring cavity interacted with two types of second-order gratings: the complex top grating containing the real part and the imaginary part modulations and the side grating. The side grating etched on the periphery of the microcylinder/microring cavity can select a whispering gallery mode with a specific azimuthal mode number, while the complex top grating can scatter the lasing mode with travelling-wave pattern vertically. With the cooperation of the gratings, the laser works with a single mode and emits radially polarized OAM beams. With an asymmetrical pad metal on the top of the cavity, the OAM on-chip laser can firstly be directly modulated with electrical pumping. Due to the small active volume, the laser with low threshold current is predicted to have a high direct modulation bandwidth about 29 GHz with the bias current of ten times the threshold from the simulation. The semiconductor OAM laser can be rather easily realized at different wavelengths such as the O band, C band, and L band.