Surface energy characteristics of toner particles by automated inverse gas chromatography

This study develops a method for the analysis of biocides Irgarol 1051 and Sea Nine 211 in environmental water samples, using solid-phase microextraction (SPME). Their determination was carried out using gas chromatography with flame thermionic (FTD), electron-capture (ECD) and mass spectrometric detection. The main parameters affecting the SPME process such as adsorption-time profile, salt additives and memory effect were studied for five polymeric coatings commercially available for solid-phase microextraction: poly(dimethylsiloxane) (100 and 30 microm), polyacrylate, poly(dimethylsiloxane)-divinylbenzene (PDMS-DVB 65 microm) and Carbowax-divinylbenzene (65 microm). The method was developed using spiked natural waters such as tap, river, sea and lake water in a concentration range of 0.5-50 microg/l. All the tested fiber coatings have been evaluated with regard to sensitivity, linear range, precision and limits of detection. Typical RSD values (triplicate analysis) in the range of 3-10% were obtained depending on the fiber coating and the compound investigated. The recoveries of biocides were in relatively high levels 60-118% and the calibration curves were reproducible and linear (R2>0.990) for both analytes. The SPME partition coefficients (Kf) of both compounds were also calculated experimentally in the proposed conditions for all fibers using direct sampling. Finally the influence of organic matter such as humic acids on extraction efficiency was studied, affecting mostly Sea Nine 211 uptake by the fiber. Optimum analytical SPME performance was achieved using the PDMS-DVB 65 microm fiber coating in ECD and FTD systems for Sea Nine 211 and Irgarol 1051, respectively.     

Surface energy of solid catalysts measured by inverse gas chromatography

The time separation of experimental surface energy on Pt-Rh bimetallic catalysts, together with the time-independent rate constants for adsorption and desorption of O(2), CO, and CO(2) on them, is described, applying the reversed-flow version of inverse gas chromatography. The standard free energy of adsorption DeltaG(z.plims;) and its probability density function over time, together with the geometrical mean of the London parts of the total surface free energy (gamma(L)(1)gamma(L)(2))(1/2) of the adsorbed probe and the solid surface, accompanied by the relevant probability density functions over time are also calculated. The time-resolved phenomena lead to quite varying values of DeltaG(z.plims;), (gamma(L)(1)gamma(L)(2))(1/2), and the distribution functions as time passes, their maximum values being given by the catalyst containing a Pt:Rh = 3:1 weight ratio of the active phase for all adsorbed gases. The conclusion is reached that the surface energy measured as described can be used as a good measure for catalyst characterization.     

反气相色谱法测定锌镁铝类水滑石的表面性能

采用水热合成法制备了锌镁铝类水滑石(ZnMgAl-HTLC),利用X射线衍射仪(XRD)对ZnMgAl-HTLC的晶体结构进行了表征,并以一系列非极性和极性分子为探针分子,采用反气相色谱法(IGC)研究了ZnMgAl-HTLC的表面性能.结果表明:XRD特征衍射峰窄、尖、高,水热合成法能够制得纯度较高的ZnMgAl-HTLC; ZnMgAl-HTLC表面吸附自由能小于零,表面色散自由能最大为6.02 mJ/m²,酸碱作用自由能最大为5.33 kJ/mol,吸附焓为43.6 kJ/mol,吸附熵为0.15 kJ/mol.本文的反气相色谱方法对研究锌镁铝类水滑石的表面性能具有重要的指导意义.     

Surface Lewis acid-base properties of polymers measured by inverse gas chromatography

Surface Lewis acid-base properties are significant for polymers materials. The acid constant, K(a) and base constant, K(b) of many polymers were characterized by some researchers with inverse gas chromatography (IGC) in recent years. In this paper, the surface acid-base constants, K(a) and K(b) of 20 kinds of polymers measured by IGC in recent years are summarized and discussed, including seven polymers characterized in this work. After plotting K(b) versus K(a), it is found that the polymers can be encircled by a triangle. They scatter in two regions of the triangle. Four polymers exist in region I. K(b)/K(a) of the polymers in region I are 1.4-2.1. The other polymers exist in region II. Most of the polymers are relative basic materials.     

Thermodynamics of miscible polymer blends studied by inverse gas chromatography

Use of inverse gas chromatography for the investigation of polymer-polymer interactions is compromised by a dependence of the measured polymer-polymer interaction coefficient, B₂₃, on the chemical nature of the probe in contradiction to theory currently used. We have developed a procedure whereby the “true” B₂₃, may be extracted from the probe dependent data. Additionally a theory of mixing based on a multidimensional solubility parameter approach has been developed. The new theory has been used to predict the polymer-polymer interaction coefficients and these are compared with experimentally determined values on several miscible blends.     

反气相色谱法测定有机溶剂型木质素的溶解度参数

采用反气相色谱法(IGC),于333.15～373.15 K温度范围内测定了有机溶剂型木质素的溶解度参数(δ2)及相关指标。以正辛烷(n-C8)、正癸烷(n-C10)、正十二烷(n-C12)和正十四烷(n-C14)为探针溶剂,计算了探针溶剂的特性保留体积(V0g)、摩尔吸收焓(ΔHs1)、无限稀释摩尔混合焓(ΔH∞1)、摩尔蒸发焓(ΔHv)、无限稀释活度系数(Ω∞1)以及探针溶剂与有机溶剂型木质素的Flory-Huggins相互作用参数(χ∞12)。结果表明,上述4种探针溶剂在测定的温度范围内均为有机溶剂型木质素的不良溶液;在同一温度下,参数χ∞12随着探针溶剂碳数的增加而降低。测得的有机溶剂型木质素的δ2为19.03 (J\5cm-3)1/2。     

Surface characterization of industrial fibers with inverse gas chromatography

Inverse gas chromatography (IGC) was applied for the determination of the surface characteristics of Tenax carbon fibers and Akzo Nobel Twaron fibers. Furthermore, IGC procedures for the determination of dispersive and acid-base interactions were validated. The data show that too high values for the dispersive component of the surface energy are obtained when the adsorption area occupied by a single adsorbed n-alkane molecule is estimated from parameters of the corresponding liquid. Comparable values are obtained when the Doris-Gray methodology (area per methylene unit) or measured probe areas are employed. For the fibers studied in this work meaningful Gibbs energy values of the acid-base interaction were only obtained with the polarizability approach. When the dispersive interaction of the polar probes with the fiber surface was scaled to the n-alkane interaction via surface tension, the boiling point, or the vapor pressure of the probes often negative acid-base interaction energies were found. From the temperature dependence of the Gibbs energy, the enthalpy of the acid-base interactions of various probes with the carbon and Twaron aramid fibers was determined. However, from these enthalpy values no meaningful acid-base surface parameters could be obtained. Generally, the limited accuracy with which these parameters can be obtained make the usefulness of this procedure questionable. Also the Gibbs energy data of acid-base interaction can provide a qualitative basis to classify the acidity-basicity of the fiber surface. This latter approach requires only a limited data set and is sufficiently rapid to enable the use of IGC as a screening tool for fibers at a production site. For several polar probes significant concentration effects on carbon fibers were observed. At very low probe loadings the interaction with the fiber surface suddenly increases. This effect is caused by the heterogeneity of the interaction energy of the active sites at the surface. A simple procedure to measure the adsorption isotherm at infinite dilution was developed. The determination of the concentration dependence of the interaction of an n-alkane, an acidic and a basic probe was incorporated in the IGC screening procedure of carbon fibers to monitor this heterogeneity.     

Surface characterization of modified glass fibers by inverse gas chromatography

The dispersive component of the surface free energy _d ^s of glass fibers and their acid-base interaction can be evaluated by the measurement of specific retention volumes of several kinds of probe molecules by use of an inverse gas chromatography. The effect of the treatment of glass fibers with silane-coupling agents was also evaluated. The specific retention volumes of n-alkanes changed linearly with theirC number or vapor pressure. Those of polar molecules varied with their donor number (DN) or acceptor number (AN). The _s ^d values and electron-accepting or donating abilities depended upon the kind of functional groups contained in the coupling agents.     

反气相色谱法表征漆酚钛螯合高聚物的表面性质

漆酚钛螯合高聚物(UTP)具有优异的耐强酸、耐强碱、耐盐类溶液、耐多种有机溶剂和耐热性能。为进一步扩大其应用领域提供理论和实验依据,采用反气相色谱法(IGC)测定了UTP在70、80、90、100和110 ℃下的表面色散自由能和表面Lewis酸碱常数。以正戊烷(C5)作为标定色谱死时间的探针分子,正己烷、正庚烷、正辛烷和正壬烷作为非极性探针分子,计算了不同温度下UTP的色散表面自由能;以四氢呋喃、丙酮和三氯甲烷作为极性探针分子,计算得到了UTP表面的酸碱作用吸附自由能和吸附焓。实验结果表明: 在70、80、90、100和110 ℃时UTP的色散表面自由能分别为37.68、33.53、35.92、24.01和31.32 mJ/m2; UTP为弱的Lewis碱,Lewis酸常数Ka为0.1853,碱常数Kb为0.9662。这一结果对研究漆酚金属螯合高聚物的表面性质与应用具有指导作用。     

Surface characterization of cellulose fibres by XPS and inverse gas chromatography

Inverse gas chromatography (IGC) was used to determine the dispersive component of the free energy as well as the acid-base properties of cellulose fibre surfaces, before and after modification by corona treatment. It was found that the corona treatment increases both the dispersive contribution to surface energy and its acidic character, whereas only a slight increase in its basicity was observed. It was also found that some chemical degradation of the surface occurs at high corona currents. The extent of modification of the surface properties, as revealed by IGC, was correlated to the surface chemical composition deduced from XPS analysis as well as with the electrical conductance and the pH of the water suspensions of the cellulose fibres.     

Correlation between mechanical adhesion and interfacial properties of starch/biodegradable polyester blends

Biopolymers are preferred ingredients for the manufacture of materials because they are based on abundantly available and renewable raw materials that have benign environmental problems associated with their production, fabrication, use, and disposal; however, the wide use of biopolymers in engineering applications has not been achieved, mainly because of the inferior quality of many biopolymer‐based products. To overcome this limitation, studies have been initiated on blends of biopolymers and biodegradable synthetic polymers. We used the contact angle of probe liquids to measure the surface energy of polystyrene, the biodegradable polyesters polycaprolactone, poly(hydroxybutyrate‐co‐hydroxyvalerate), polylactic acid, polybutylene adipate terephthalate, and adipic poly(hydroxy ester ether), and normal starch. The surface energies were used to estimate the starch/polymer interfacial energy and work of adhesion. The calculated starch/polyester work of adhesion showed mixed correlation with published starch/polyester mechanical properties, indicating that factors other than interfacial properties might be dominant in determining the mechanical properties of some starch/polyester blends. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 920–930, 2001     

反相气相色谱法表征聚丁二烯橡胶的表面性质

采用反相气相色谱技术测定了聚丁二烯橡胶的表面性质。以正己烷、正庚烷、正辛烷、正壬烷作为非极性探针测定其表面色散自由能,以二氯甲烷、三氯甲烷、丙酮、乙酸乙酯、乙醚和四氢呋喃作为极性探针测定其路易斯酸碱常数。经计算得出聚丁二烯橡胶在303、313、323、333和343 K的表面色散自由能分别为47.07、46.46、45.85、45.60和45.09 mJ/m2。结果表明,聚丁二烯橡胶表面色散自由能随着温度的升高呈线性降低,路易斯酸常数Ka为0.34,碱常数Kb为1.77,总酸碱作用能力2.11,该聚合物为弱碱性Lewis两性聚合物材料。此外还计算出聚丁二烯橡胶的酸碱作用吸附自由能（~ΔGsa）和吸附焓（~ΔHsa）。     

Surface characterization of macroporous glycidyl methacrylate based copolymers by inverse gas chromatography

Two samples of macroporous crosslinked poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate), PGME, with different porosity parameters were synthesized by suspension copolymerization and modified by ring-opening reaction of the pendant epoxy groups with ethylene diamine, EDA. Inverse gas chromatography at infinite dilution was used for the determination of adsorption properties of PGME, and copolymer modified with ethylene diamine, PGME-en. Thermodynamic parameters of adsorption, dispersive components of the surface free energies, and the acid/base constants for the copolymer samples were calculated. The calculated dispersive surface energy values, , for PGME and PGME-en are comparable with the literature data for nonconductive polymers.     

Surface characterization and London dispersive surface free energy of functionalized single-walled carbon nanotubes with a blend of polytetrafluoroethylene by inverse gas chromatography

The SWCNTs and SWCNT-polytetrafluoroethylene (PTFE) blend were prepared by using simple reaction mixture in the presence of chromosorb (SiO₂). Surface morphology of SWCNTs and (SWCNT-PTFE) blend was characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thermal gravimetric analysis (TGA), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and surface BET analysis. In addition, the surface thermodynamic properties of n-alkanes and polar probe net retention volumes are measured by inverse gas chromatography (IGC). The London dispersive surface free energy values were found to be decreased linearly with increase of temperature. The specific component of the surface free energy of adsorption for the polar probes was obtained using the Donnet-Park method. The surface character “S” value (K_b/K_a) at SWCNTs was found to be 0.74, and SWCNT-PTFE blend surface character value was found to be 0.86. This result demonstrates that the (SWCNT-PTFE) blend surface contains relatively more acidic sites then that of SWCNT surface. Therefore, the IGC results provide useful complementary information on the (SWCNT-PTFE) blend surface.     

Investigation of thermodynamic properties of hyperbranched aliphatic polyesters by inverse gas chromatography

Thermodynamic properties of a series of commercial hyperbranched aliphatic polyesters (Boltorn^® H20, H30 and H40) were examined for the first time by inverse gas chromatography (IGC) using 13 different solvents at infinite dilution as probes. Retention data of probes were utilized for an extensive characterization of polymers, which includes the determination of the Flory–Huggins interaction parameter, the weight fraction activity coefficient as well as the total and partial solubility parameters. Analysis of the results indicated that the total and partial solubility parameters decrease with increase of temperature. Furthermore, upon increase of the molecular weight, while the hydrogen bonding component decreases, no influence on the total solubility parameter is noticed within the experimental error margins. Results from the present study while providing new insight to the thermodynamic characteristics of the examined systems, they are also expected to reflect more general aspects of the behavior of hyperbranched polymers bearing similar end-groups.     

Effect of emulsifiers on surface properties of sucrose by inverse gas chromatography

Inverse gas chromatography (IGC) was employed to characterize the changes in surface properties of sucrose particles coated with either lecithin or polyglycerol polyricinoleate. IGC was performed using polar and non-polar adsorbates at infinite dilution with the sucrose particles as the solid stationary phase. Coating the sugar surface with emulsifiers induced an increase in the lipophilicity of the sugar particles, i.e. a sharp decrease in the acidity of the surface. Yet the two emulsifiers induced a slightly different increase in the surface basicity. It was hypothesized that this observation was due to a difference in the molecular structure of the emulsifiers.     

Surface characterization of poly(lactic acid) and polycaprolactone by inverse gas chromatography

Inverse gas chromatography (IGC) has been used to characterise the surface properties of polycaprolactone (PCL) and poly(lactic acid) (PLA). The dispersive component of the surface free energy (gamma(S)(D)) was found to be very small for both of them--values close to 30 mJ/m(2) in the case of the PLA and ca. 40 mJ/m(2) for the PCL. The retention times of the n-alkanes, necessary to calculate the dispersive component of the surface energy, were obtained from the maximum, the centre at half height and the centre of mass of the chromatographic peak. While the values obtained using the first two parameters appear not to be affected by the peak asymmetry, in spite of having been obtained above the glass transition temperature of the polymer, the values obtained using the latter have been found to be not reliable. The drawbacks of using n-alkanes with a very small retention time have also been discussed, estimating the error it can introduce in the final results. Finally, the acid-base properties of the two biopolymers were determined using the approaches suggested by Schultz et al. and by St. Flour and Papirer. Although both methods describe the surfaces of PLA and PCL as neutral ones, differences between the values of the parameters K(A), K(D) and S(C) were obtained.