Interfacial oxidation of ultrathin nickel and chromium films on yttria-stabilized zirconia

The substrate-induced oxidation upon prolonged annealing in UHV of ultrathin films of Ni and Cr vapor deposited on yttria-stabilized zirconia YSZ(100) was studied by X-ray photoelectron spectroscopy (XPS) to obtain information about the oxidation mechanism, determine the available quantity of reactive oxygen in YSZ, and investigate the thermal stability of the thin oxide films. Up to about 0.8 ML of Ni deposited at room temperature was oxidized to NiO at a constant rate at 650 K via the substrate, whereas at slightly higher coverage, the oxidation rate under identical conditions was drastically reduced. In contrast to Ni, up to 4.8 ML of Cr deposited at 275 K could be oxidized via the substrate to Cr2O3 upon extensive UHV annealing at increasing temperature up to 820 K, indicating a reactive oxygen content of at least 4 x 10(-6) with respect to the lattice oxygen in the YSZ specimen. The Cr2O3 decomposed to metallic Cr above about 800 K, whereas NiO was stable up to the maximum temperature of 875 K. These results indicate that the oxidation via the substrate is kinetically analogous to the gas-phase oxidation of bulk Ni and Cr. The reactive oxygen content of the single-crystal YSZ is larger than expected, and part of it is accommodated at the surface of the substrate. The thermal stability of the thin oxide films is determined by the oxygen exchange with YSZ and not by the respective bulk oxide thermodynamic decomposition temperature.     

Structural phase transition in ultrathin films of disk-shaped molecules

We have used grazing-incidence X-ray diffraction and atomic force microscopy to study Langmuir-Blodgett films of 2-(3-hydroxypropyl)oxy-3,6,7,10,11-pentapentyloxytriphenylene, a disk-shaped molecule which also forms a bulk liquid crystalline columnar phase. Upon heating, we observe a phase transition from a low symmetry ordered crystalline structure to a high temperature liquid crystal. The transition is reversible, with considerable hysteresis.     

Surface-induced phase transitions in ultrathin films of block copolymers

We study theoretically the lamellar-disorder-lamellar phase transitions of AB diblock and tetrablock copolymers confined in symmetric slitlike pores where the planar surface discriminatingly adsorbs A segments but repels B segments, mimicking the hydrophobic/hydrophilic effects that have been recently utilized for the fabrication of environmentally responsive "smart" materials. The effects of film thickness, polymer volume fraction, and backbone structure on the surface morphology have been investigated using a polymer density-functional theory. The surface-induced phase transition is manifested itself in a discontinuous switch of microdomains or a jump in the surface density dictated by the competition of surface adsorption and self-aggregation of the block copolymers. The surface-induced first-order phase transition is starkly different from the thickness-induced symmetric-asymmetric or horizontal-vertical transitions in thin films of copolymer melts reported earlier.     

Dispersion and phase separation of carbon nanotubes in ultrathin polymer films

The inner structure and nanoscale distribution of the stiffness was studied for polymer-single-wall carbon nanotube composites. Dispersion of nanotubes in a polystyrene and polyurethane polymer matrix was achieved by a proper choice of the organic solvent (NMP) and sonification of polymer/SWNT solutions. Ultrathin nanocomposite films were prepared through a dip-coating procedure and possessed a noticeable degree of nanotube orientation in the direction of the applied shear force. Peculiarities of the phase separation in the films were studied by atomic force microscopy (with application of force modulation mode to map the nanotube distribution within the polymer matrix) and Raman spectroscopy.     

Two-dimensional molecular ordering of Os(II) complexes in organo-clay hybrid ultrathin films

An ordered structure of [OsL(3)](2+)(L = 2, 2'-bipyridine or 1, 10-phenanthroline) layer in an ultrathin film composed of the complex cations, clay nanosheets and alkylammonium cations is reported on the basis of its in-plane X-ray diffraction and polarized electronic spectral data.     

Selective solvent annealing induced phase separation and dewetting in PMMA/SAN blend ultrathin films

Phase behaviors induced by solvent annealing in poly(methyl methacrylate) (PMMA) and poly(styrene‐ran‐acrylonitrile) (SAN) blend ultrathin films have been investigated by atomic force microscopy and grazing incidence small‐angle X‐ray scattering. Our results indicate that both the phase separation within the blend and the dewetting of the film induced by composition fluctuation take place upon the selective solvent annealing, producing complex structures containing upper droplets (of one phase) and mimic‐films (of the other rich‐phase). The use of acetic acid (the selective solvent for PMMA) generates PMMA mimic‐film and SAN droplets, while the introduction of DMF (exhibiting better solubility for SAN) vapor results in the formation of SAN mimic‐film and PMMA droplets. Essentially, the interaction at polymer/substrate interface, resultant wettability of selected component, solubility of PMMA and SAN in adopted solvent dominate not only the phase separation and the dewetting of the whole film but also the synergism of them. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1243–1251     

Bulk and surface composition, amorphous structure, and thermocrystallization of electrodeposited alloys of tungsten with iron, nickel, and cobalt

It has been shown for iron-group alloys of tungsten, using ESCA spectroscopy of samples sputtered with argon ions and SEM/EDS analysis, that no oxygen is present in the alloy bulk. A very weak internal organization in the alloys, which follows from low and wide diffractograms usually obtained for electrodeposited layers, is thought to be a heavily distorted structure of the major metal component of the alloy. Thermal crystallization of thin layers of the amorphous tungsten alloys does not lead to formation of well-known intermetallic crystal structures. Received: 19 January 1998 / Accepted: 17 July 1998     

Zinc and nickel ferrocyanides: preparation, composition and structure

A review is given of work on nickel and zinc ferrocyanides during the period 1922–1983 with an emphasis on their compositions and structures in relation to the methods of preparation.     

Magnetism and surface structure of atomically controlled ultrathin metal films

We review the correlation of magnetism and surface structure in ultrathin metal films, including the tailoring of novel magnetic properties using atomic scale control of the nanostructure. We provide an overview of modern fabrication and characterization techniques used to create and explore these fascinating materials, and highlight important phenomena of interest. We also discuss techniques that control and characterize both the magnetic and structural properties on an atomic scale. Recent advances in the development and applications of these techniques allow nanomagnetism to be investigated in an unprecedented manner.A system cannot necessarily retain a two-dimensional structure as it enters the ultrathin region, but it can transform into a three-dimensional, discontinuous structure due to the Volmer–Weber growth mechanism. This structural transformation can give rise to superparamagnetism. During this evolution, competing factors such as interparticle interactions and the effective magnetic anisotropy govern the magnetic state. These magnetic parameters are influenced by the nanostructure of the film. In particular, controlling the magnetic anisotropy is critical for determining the magnetic properties. Surface effects play especially important roles in influencing both the magnitude and direction of the magnetic anisotropy in ultrathin films. By properly altering the surface structure, the strength and direction of the magnetic anisotropy are controlled via spin–orbit and/or dipole interactions.     

The structure of ultrathin Langmuir-Blodgett films of cadmium behenate

Grazing incidence x-ray-diffraction investigations of the structures of Langmuir-Blodgett films of cadmium behenate with 1, 2, 3, 5, and 21 monolayers are reported. The single monolayer film, deposited on a hydrophilic substrate, showed a hexagonal structure, whereas the bilayer film, deposited on a hydrophobic substrate, had a rectangular structure with herringbone orientation of the acyl chains. With multilayer films formed on a hydrophilic substrate, it was possible to detect that the hexagonal structure of the first layer was retained when additional layers were deposited and that the additional layers had the same rectangular structure as the bilayer.     

Long-range magnetic ordering in iron jarosites prepared by redox-based hydrothermal methods

The iron jarosites, plumbojarosite, Pb0.5Fe3(OH)6(SO4)2, argentojarosite, AgFe3(OH)6(SO4)2, and thallium jarosite, TlFe3(OH)6(SO4)2, along with the selenate-capped jarosite analogues of potassium, KFe3(OH)6(SeO4)2, and rubidium, RbFe3(OH)6(SeO4)2, have been prepared in their analytically pure forms by employing redox-based hydrothermal methods. The crystal structures of these materials have been determined, and all are found to be essentially isostructrual including Pb0.5Fe3(OH)6(SO4)2, which is distinct from the structure reported for naturally mined samples. All iron jarosites show long-range order (LRO), signified by a sharp transition temperature, T(N), which falls in the narrow temperature range of 61.4 +/- 5 K. The mechanism responsible for this ordering has been established by examining magnetostructural correlations for the jarosites possessing various interlayer cation and capping groups. We show that all magnetic properties of jarosites, including LRO, find their origin in the basic magnetic unit, the intralayer Fe3(mu-OH)3 triangle. Field-dependent magnetization experiments are consistent with the antiferromagnetic stacking of an out of plane moment developed from spin canting within Fe3(mu-OH)3 triangles. Together with the previously reported AFe3(OH)6(SO4)2 (A = Na+, K+, Rb+ and NH4+) jarosites, these compounds provide a framework for probing magnetic ordering in a spin frustrated lattice of the largest series of isoelectronic and isostructural kagomé systems yet discovered.     

Molecular ordering and 2D conductivity in ultrathin poly(3-hexylthiophene)/gold nanoparticle composite films

This paper reports the first comparison of the structure and electrical conductivity properties of spin cast (SC) and Langmuir-Schaeffer (LS) films of regioregular poly(3-hexylthiophene) (P3HT). In addition, the effect of incorporating highly monodisperse Au nanoparticles (NPs), with a core diameter of approximately 5 nm, into SC and LS P3HT films is described. A detailed picture of molecular organization in the films has been obtained using ultraviolet-visible absorption spectroscopy, atomic force microscopy, field-emission scanning electron microscopy, X-ray diffraction, and X-ray reflectivity. Film morphology was correlated with pseudo-two-dimensional conductivity measured using scanning electrochemical microscopy, with P3HT in the semiconducting regime. It was found that SC films, which were slightly thicker than those formed with the LS technique, exhibited greater organization. This resulted in an order of magnitude higher lateral conductivity for the SC films. Inclusion of Au NPs (50 wt %) into both SC and LS films resulted in the formation of uniform and relatively flat (rms roughness approximately 1 nm) composite films. Surprisingly, the addition of NPs did not disrupt the characteristic crystal structure found for the native P3HT films. The effect of Au NPs on film lateral conductivity was found to be determined by the distribution of Au NPs within the polymer, which varied significantly between SC and LS films. Whereas Au NPs aggregated into hexagonally packed clusters in SC films, NPs in LS films were predominantly uniformly distributed between the lamella bilayer. It was found that, while the inclusion of Au NPs caused the lateral conductivity to decrease in SC films, in LS films, the lateral conductivity increased by a factor of 2.     

Infrared spectroscopic studies on crystalline phase transition of PVDF and PVDF/hyperbranched polyester blend ultrathin films

In this study, as cast (AC, at 30 °C) and annealed (AN, at 130 °C, 3 h) samples of polyvinylidene fluoride (PVDF) and PVDF/hyperbranched polyester (HBP) (90/10) blend ultrathin films were subjected to heating-cooling (30 → 210 → 30 °C) cycle, and studied for their changes in crystalline phase transition behavior using in-situ Fourier transform infrared-transmission spectroscopy (FTIR-TS) and grazing incident reflection absorption spectroscopy (FTIR-GIRAS) techniques. Factor analysis was employed to extract the pure crystalline and amorphous spectra as well as the percentage content of ferroelectric crystallinity for both the samples. Irrespective of the thermal treatment (AC or AN) and spectral measurement (FTIR-TS or GIRAS) techniques, neat PVDF sample exhibited irreversible phase transitions during heating-cooling cycle associated with the transformation from ordered β-crystalline (1276 cm⁻¹) into disordered amorphous (1234 cm⁻¹) form. Interestingly, annealed PVDF/HBP blend sample measured using FTIR-GIRAS exhibited reversible crystalline phase transition behavior similar to a ‘dipole memory effect’ even after heating to 210 °C (>T_m) and then cooled to 30 °C. Compared to neat PVDF, higher ferroelectric crystallinity and reversible phase transition in PVDF/HBP blend may be attributed to (i) the existence of H-bonding between HBP (CO and OH groups) and PVDF (CH₂ and CF₂) and/or (ii) HBP acting as a nanoparticle in PVDF matrix.     

Conditions of hydrochemical synthesis, composition, and structure of tellurium films

Conditions of the hydrochemical synthesis of thin tellurium fi lms by reduction of an aqueous solution of tellurous acid with hydrazine were determined. The redox potentials of tellurous acid and hydrazine and their difference in relation to pH of the medium and concentration of tellurite ions were calculated. The kinetics of tellurium layer growth on glass-ceramic substrates and the structure, composition, and morphology of the layers were studied.     

Exploiting distinct molecular architectures of ultrathin films made with iron phthalocyanine for sensing

The possibility of generating distinct film properties from the same material is crucial for a number of applications, which can only be achieved by controlling the molecular architecture. In this paper we demonstrate as a proof-of-principle that ultrathin films produced from iron phthalocyanine (FePc) may be used to detect trace amounts of copper ions in water, where advantage was taken of the cross sensitivity of the sensing units that displayed distinct electrical properties. The ultrathin films were fabricated with three methods, namely physical vapor deposition (PVD), Langmuir-Blodgett (LB), and electrostatic layer-by-layer (LbL) techniques, where for the latter tetrasulfonated phthalocyanine was used (FeTsPc). PVD and LB films were more homogeneous than the LbL films at both microscopic and nanoscopic scales, according to results from micro-Raman spectroscopy and atomic force microscopy (AFM), respectively. From FTIR spectroscopy data, these more homogeneous films were found to have FePc molecules oriented preferentially, tilted in relation to the substrate surface, while FeTsPc molecules were isotropically distributed in the LbL films. Impedance spectroscopy measurements with films adsorbed onto interdigitated gold electrodes indicated that the electrical response depends on the type of film-forming method and varies with incorporation of copper ions in aqueous solutions. Using principal component analysis (PCA), we were able to exploit the cross sensitivity of the sensing units and detect copper ions (Cu(2+)) down to 0.2 mg/L, not only in ultrapure water but also in distilled and tap water. This level of sensitivity is sufficient for quality control of water for human consumption, with a fast, low-cost method.     

Nanopatterning and nanocharge writing in layer-by-layer quinquethiophene/phthalocyanine ultrathin films

Nanometer-scale patterning and charging in layer-by-layer (LbL) ultrathin films of quinquethiophene (5TN)/phthalocyanine (CuPS) provides a novel write-read device using a standard current-sensing atomic force microscopy (CS-AFM). The AFM height images showed dented or raised morphological features that could be selectively manipulated by changing the direction of the bias voltages. The conductivity was repeatedly changed between a conductive and insulating state, originating from an electrochemical charging-discharging effect. This was attributed to electrochemical ion transport and the residual mobile ions present in LbL films. Finally, the nanocharge pattern was written by CS-AFM and read out in a conductivity map image.     

基于MCM-41硬模板的镍铁磁性纳米管的合成及其磁性研究

以Si-MCM-41为硬模板,利用介孔材料的吸附作用,将Fe3+和Ni 2+按一定比例定量吸附组装到介孔材料的孔壁上;然后通过程序升温在900℃条件下高温焙烧,并经氢氟酸处理,得到直径大约为3.0nm的中空铁氧体纳米管.分别利用傅立叶变换红外光谱仪、扫描电镜、透射电镜、X射线衍射仪分析了合成材料的结构、组成、形貌;采用振动样品磁强计测定了其磁性能.结果表明,合成的镍铁氧体纳米管具有良好的管状形貌,其结构与分子筛MCM-41的结构相似,并具有良好的磁学性能.这说明MCM-41分子筛孔道结构具有可复制性,本研究可望为制备具有适当长径比的一维纳米磁性材料打下良好基础.