0,1,3维CeO2的可控制备及CuO/CeO2催化剂上CO氧化反应

以水、乙醇和乙二醇为溶剂,采用溶剂热法可控制备了0,1,3维CeO2.结果表明,0维CeO2由0.2～0.5 μm纳米粒子组成;1维CeO2是直径为25～30 μm,长约500 μm的六方棒;松针型的3维CeO2是由以纳米粒子为单元构成的直径为1～5 μm,长约50 μm的光滑棒组成,其比表面积高达234 m2/g.将...     

非表面活性剂合成CeO2介孔材料

以非表面活性剂三乙胺(TEA)和聚乙二醇(PEG)为模板剂,合成了具有立方莹石晶相结构的介孔CeO2材料,通过XRD,HRTEM,BET,FTIR和选区电子衍射(SAED)等手段对介孔CeO2进行了表征。考察了模板剂在CeO2介孔结构的形成过程中所起的作用及其对比表面、孔径分布、热稳定性的影响,并对模板剂的作用机制进行了分析。结果表明,三乙胺在CeO2介孔结构的形成中起关键作用,聚乙二醇对介孔结构热稳定性有明显的改善作用,经600℃焙烧3h的样品仍能保持较好的介孔结构,其介孔呈直通型的六方型孔道,比表面积>200m2·g-1,孔分布呈双孔型分布,其中介孔孔径约为5nm左右,微孔孔径在1～2nm之间,介孔占较大比例,并且微孔数量随焙烧温度的升高逐渐减少,直至600℃消失。     

双锥状纳米晶TiO2微管的制备及其光催化性能

本文采用模板法与溶胶-凝胶法结合,以脱脂棉为模板制备出了TiO2中空微管光催化材料.利用红外光谱(FTIR)、扫描电镜(SEM)、透射电镜(TEM)、X射线衍射(XRD)对其在不同煅烧温度下产物的表面形貌及晶型进行了表征.以甲基橙的脱色降解为模式反应,考察了宏观形貌及煅烧温度对TiO2光催化性能的影响.结果表明:以脱脂棉为模板制得的TiO2中空微管直径3～8μm、壁厚0.5～1μm,TiO2晶体直径为30～80 nm,长径比约为5:1,呈双锥状结构,微管样品在酸性条件下30min内对甲基橙催化降解效率提高了约16%～40%.     

双模板法制备具有介孔孔壁的三维有序大孔二氧化铈及其改善的低温还原性能

以聚甲基丙烯酸甲酯(PMMA)为硬模板,三嵌段共聚物F127、十六烷基三甲基溴化铵(CTAB)或聚乙二醇(PEG)为软模板剂(表面活性剂),柠檬酸为络合剂,硝酸铈为金属前驱体,采用双模板法成功地合成出具有介孔孔壁的三维有序大孔(3DOM)结构的立方相CeO2样品CeO2-F127,CeO2-CTAB和CeO2-PEG,...     

基于CeO2-Co3O4纳米纤维的催化发光式甲醛传感器研究

采用双喷嘴静电纺丝法制备了CeO2-Co3 O4纳米纤维,将制备的CeO2-Co3 O4纳米纤维均匀涂覆于 ω型加热线圈表面形成催化发光薄膜,设计了一种新型催化发光甲醛传感器.采用X射线衍射仪、 扫描电子显微镜、 全自动程序化学吸附仪和X-射线光电子能谱仪,表征了Co3 O4-CeO2纳米纤维的相组成和微观形貌,讨论了甲醛在CeO2-Co3 O4催化剂表面的电化学特性和催化发光机理.在优化条件下,即波长500 nm、 温度550℃ 、 载气流速0.2 L/min,甲醛传感器件(Ce30)催化发光强度与甲醛浓度在1.2~50μg/m3范围内有良好的线性关系,灵敏度为40.04 a.u./(μg/m3),检出限为1.2μg/m3,动态响应和恢复时间分别为2.4和3.5 s.此传感器可用于汽车尾气中甲醛浓度检测,相对误差范围为0.4%~1.1%,相对标准偏差RSD<3%(n=6).     

基于碳纳米管的氧化铈纳米管的合成及表征

建立了一种制备氧化铈纳米管的新方法, 即以碳纳米管(CNTs)为模板, 在常温常压下采用液相沉积法在CNTs表面包覆CeO2, 通过煅烧除去CNTs模板, 得到氧化铈纳米管. 通过透射电子显微镜(TEM)、X射线衍射(XRD)和X射线光电子能谱(XPS)对其形貌和结构进行了表征. 所得CeO2纳米管为面心立方结构, 直径40~60 nm, 长度0.5~2 μm.     

同轴静电纺丝技术制备CeO2纳米管及光催化性能研究

采用同轴静电纺丝技术,以硝酸铈、聚乙烯吡咯烷酮、N,N-二甲基甲酰胺和氯仿为原料,制备了CeO2纳米管。用差热-热重分析、X射线衍射、扫描电镜、透射电镜和能谱仪对样品进行了表征。考察了CeO2纳米管对罗丹明B溶液的光催化性能。结果表明:所得到的产物属于立方晶系、空间群为O5H-FM3M的CeO2纳米管,CeO2纳米管平均外径约270 nm,内径约110 nm,管壁厚度约80 nm,长度>20μm,对其形成机理进行了分析。相对于CeO2纳米线、纳米带和CeO2颗粒,CeO2纳米管对罗丹明B的降解率有明显提高。     

阳极氧化铝模板合成介孔CeO2纳米纤维及其光致发光性能

以多孔阳极氧化铝膜(AAO)为模板,将模板的纳米孔洞作为微腔反应器,以聚环氧乙烯醚-聚环氧丙烯醚-聚环氧乙烯醚三嵌段共聚物(P123)为致孔剂、Ce(NO3)3.6H2O为铈源、无水乙醇为溶剂合成前躯体,采用压力诱导的方法将前躯体注入到AAO孔道内,经加热处理后,在模板的纳米孔洞内合成了具有介孔结构的一维CeO2纳米材料。通过SEM、TEM、XRD、EDS和N2吸附-脱附进行表征,结果表明,所合成的介孔CeO2纳米纤维具有介孔结构和较大的比表面积,并考察了其光致发光性能。     

多孔玻璃载体自转晶B-Al-MFI型沸石膜的原位合成

在乙胺和水的混合蒸汽相中,首次通过载体自转晶,在多孔玻璃表面原位合成了B-Al-MFI型沸石膜。X射线衍射和扫描电镜观察证明,膜中沸石晶体的取向是随机的。晶体尺寸约为15～25μm,单层晶体厚的膜约为10～20μm。在焙作去有机模板剂后的沸石膜上,O~2和N~2的透过性分别为0.095×10^-^8和0.15×10^-^8mol/(m^2·s·Pa)。计算的O~2/N~2的理想选择值(0.63)明显低于诺森扩散的理想选择性值(0.94)和透过原载体的理想选择性值(0.91)。     

拉伸微模塑制备低密度聚乙烯超疏水表面

以新鲜荷叶为原始模板制备聚二甲基硅氧烷(PDMS)软模板,并用该软模板在真空下热压得低密度聚乙烯(LDPE),冷却剥离得到LDPE超疏水薄膜.场发射扫描电镜(FE-SEM)显示其表面由细长乳突(长约30 μm)构成,接触角为154°±3.5°,水滴极易滚落,而常压下热压得到的薄膜表面乳突则短而粗(长约8～10μm),接触角仅137°±2.7°,短粗的乳突高度接近模板微坑的深度,证明细长乳突是在微模塑脱模时拉伸形成的.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.