Alkyl chain barriers for kinetic optimization in dye-sensitized solar cells

The optimization of interfacial charge transfer is crucial to the design of dye-sensitized solar cells. In this paper we address the dynamics of the charge separation and recombination in liquid-electrolyte and solid-state cells employing a series of amphiphilic ruthenium dyes with varying hydrocarbon chain lengths, acting as an insulating barrier for electron-hole recombination. Dynamics of electron injection, monitored by time-resolved emission spectroscopy, and of charge recombination and regeneration, monitored by transient optical absorption spectroscopy, are correlated with device performance. We find that increasing dye alkyl chain length results in slower charge recombination dynamics to both the dye cation and the redox electrolyte or solid-state hole conductor (spiro-OMeTAD). These slower recombination dynamics are however paralleled by reduced rates for both electron injection into the TiO2 electrode and dye regeneration by the I-/I3- redox couple or spiro-OMeTAD. Kinetic competition between electron recombination with dye cations and dye ground state regeneration by the iodide electrolyte is found to be a key factor for liquid electrolyte cells, with optimum device performance being obtained when the dye regeneration is just fast enough to compete with electron-hole recombination. These results are discussed in terms of the minimization of kinetic redundancy in solid-state and liquid-electrolyte dye-sensitized photovoltaic devices.     

Enhanced light harvesting in mesoporous TiO2/P3HT hybrid solar cells using a porphyrin dye

We report panchromatic light harvesting in hybrid TiO(2)/P3HT photovoltaic devices using a porphyrin dye that complements the light absorption of P3HT. The high short circuit photocurrent (12.1 mA cm(-2)) obtained is found to be due, in part, to F?rster resonance energy transfer from the P3HT to the dye.     

纳米结构TiO2/聚3-己基噻吩多孔膜电极光电性能研究

用光电流作用谱、光电流-电势图等光电化学方法研究了ITO/聚3-己基噻吩(ITO/ P3HT)膜和纳米结构TiO2/聚3-己基噻吩(TiO2/P3HT)复合膜的光电转换性质. 结果表明, P3HT膜的禁带宽度为1.89 eV, 价带位置为－5.4 eV. 在ITO/TiO2/ P3HT复合膜电极中存在p-n异质结, 在一定条件下异质结的存在有利于光生电子-空穴对的分离. P3HT修饰ITO/TiO2电极可使光电流发生明显的红移, 从而提高了宽禁带半导体的光电转换效率.     

Improved efficiency of photovoltaics based on CdSe nanorods and poly(3-hexylthiophene) nanofibers

We present photovoltaic devices based on a blend of the conjugated polymer poly(3-hexylthiophene) (P3HT) with cadmium selenide nanorods, where the solvent for film deposition has been carefully chosen to optimize the film morphology. Using 1,2,4-trichlorobenzene (TCB), which has a high boiling point, as solvent for P3HT it is possible to obtain a fibrilar morphology, providing extended pathways for hole transport. Blend devices fabricated using this solvent gave solar power conversion efficiencies of 2.6%. This indicates that efficient transport of electrons and holes is achieved in these films, allowing them to operate effectively at solar illumination intensities.     

Interplay of three-dimensional morphologies and photocarrier dynamics of polymer/TiO2 bulk heterojunction solar cells

In this study, we investigated the interplay of three-dimensional morphologies and the photocarrier dynamics of polymer/inorganic nanocrystal hybrid photoactive layers consisting of TiO(2) nanoparticles and nanorods. Electron tomography based on scanning transmission electron microscopy using high-angle annular dark-field imaging was performed to analyze the morphological organization of TiO(2) nanocrystals in poly(3-hexylthiophene) (P3HT) in optimal solar cell devices. The Three-dimensional (3D) morphologies of these hybrid films were correlated with the photocarrier dynamics of charge separation, transport, and recombination, which were comprehensively probed by various transient techniques. Visualization of these 3D bulk heterojunction morphologies clearly reveals that elongated and anisotropic TiO(2) nanorods in P3HT not only can significantly reduce the probability of the interparticle hopping transport of electrons by providing better connectivity with respect to the TiO(2) nanoparticles, but also tend to form a large-scale donor-acceptor phase-separated morphology, which was found to enhance hole transport. The results support the establishment of a favorable morphology for polymer/inorganic hybrid solar cells due to the presence of the dimensionality of TiO(2) nanocrystals as a result of more effective mobile carrier generation and more efficient and balanced transport of carriers.     

High efficiency of dye-sensitized solar cells based on metal-free indoline dyes

We now report metal-free organic dyes having a new type of indoline structure, which exhibits high efficiencies in dye-sensitized solar cells. The solar energy to current conversion efficiencies with the new indoline dye was 6.51%. Under the same conditions, the N3 dye was 7.89% and the N719 dye was 8.26%. The new indoline dye was optimized for the amount of 4-tert-butyl pyridine in the electrolyte and cholic acid as a coadsorbent. Subsequently, the solar energy to current conversion efficiencies reached 8.00%. This value was the highest obtained efficiency for dye-sensitized solar cells based on metal-free organic dyes without an antireflection layer.     

A non-fullerene acceptor enables efficient P3HT-based organic solar cells with small voltage loss and thickness insensitivity

The large D core of DFPCBR results in efficient P3HT-based OSCs with a high V_OC and thickness insensitivity.     

Flexible dye sensitised nanocrystalline semiconductor solar cells

We report here flexible solid-state solar cells based upon dye-sensitised nanocrystalline Al2O3 coated TiO2 films and an I2/NaI doped solid-state polymer electrolyte. Such devices show remarkably high solar-light to electrical energy conversion efficiencies of approximately 5.3% under 10 mW cm-2 AM1.5 illumination.     

Tuning the HOMO energy levels of organic dyes for dye-sensitized solar cells based on Br-/Br3- electrolytes

A series of novel metal-free organic dyes TC301-TC310 with relatively high HOMO levels were synthesized and applied in dye-sensitized solar cells (DSCs) based on electrolytes that contain Br(-)/Br(3)(-) and I(-)/I(3)(-). The effects of additive Li(+) ions and the HOMO levels of the dyes have an important influence on properties of the dyes and performance of DSCs. The addition of Li(+) ions in electrolytes can broaden the absorption spectra of the dyes on TiO(2) films and shift both the LUMO levels of the dyes and the conduction band of TiO(2), thus leading to the increase of J(sc) and the decrease of V(oc). Upon using Br(-)/Br(3)(-) instead of I(-)/I(3)(-), a large increase of V(oc) is attributed to the enlarged energy difference between the redox potentials of electrolyte and the Fermi level of TiO(2), as well as the suppressed electron recombination. Incident photon to current efficiency (IPCE) action spectra, electrochemical impedance spectra, and nanosecond laser transient absorption reveal that both the electron collection yields and the dye regeneration yields (Φ(r)) depend on the potential difference (the driving forces) between the oxidized dyes and the Br(-)/Br(3)(-) redox couple. For the dyes for which the HOMO levels are more positive than the redox potential of Br(-)/Br(3)(-) sufficient driving forces lead to the longer effective electron-diffusion lengths and almost the same efficient dye regenerations, whereas for the dyes for which the HOMO levels are similar to the redox potential of Br(-)/Br(3)(-), insufficient driving forces lead to shorter effective electron-diffusion lengths and inefficient dye regenerations.     

Functionalized methanofullerenes used as n-type materials in bulk-heterojunction polymer solar cells and in field-effect transistors

The synthesis of two well-solubilized [60]methanofullerene derivatives ( p- EHO-PCBM and p- EHO-PCBA) is presented for usage in organic solar cells and in field-effect transistors. The para position of the PCBM's phenyl ring was substituted with a branched alkoxy side chain, which contributes to higher solubility, facilitating synthesis, purification, and processing. We find a small change of the open-circuit voltage ( V oc) as a slight improvement in performance upon application in P3HT/[60]methanofullerene bulk-heterojunction-photovoltaic cells, when compared to PCBM, because of the electron donation of the alkoxy group. In the case of the devices with a TiO x layer, the best power conversion efficiencies (PCE, eta e) is observed in a layered structure of P3HT/ p- EHO-PCBA/TiO x (eta e = 2.6%), which slightly exceeds that of P3HT/PCBM/TiO x (eta e = 2.3%) under conditions reported here. This can be attributed, in part, to the carboxylic acid group in p- EHO-PCBA that leads to an effective interface interaction between the active layer and TiO x phase. In addition, n-channel organic field-effect transistor (OFET) devices were fabricated with thin films of p- EHO-PCBM and p- EHO-PCBA, respectively cast from solution on SiO 2/Si substrates. The values of field-effect mobility (mu) for p- EHO-PCBM and p- EHO-PCBA are 1 x 10 (-2) and 1.6 x 10 (-3) cm (2)/V.s, respectively. The results in this paper demonstrate the effects of a carboxylic acid group and an electron-donating substituent in [60]methanofullerenes as n-type materials with respect to organic solar cells and OFET applications.     

Phenoxazine dyes for dye-sensitized solar cells: relationship between molecular structure and electron lifetime

A series of metal-free organic dyes with a core phenoxazine chromophore have been synthesized and tested as sensitizers in dye-sensitized solar cells. Overall conversion efficiencies of 6.03-7.40% were reached under standard AM 1.5G illumination at a light intensity of 100 mW cm(-2) . A clear trend in electron lifetime could be seen; a dye with a furan-conjugated linker showed a shorter lifetime relative to dyes with the acceptor group directly attached to the phenoxazine. The addition of an extra donor unit, which bore insulating alkoxyl chains, in the 7-position of the phenoxazine could increase the lifetime even further and, together with additives in the electrolyte to raise the conduction band, an open circuit voltage of 800 mV could be achieved. From photoelectron spectroscopy and X-ray absorption spectroscopy of the dyes adsorbed on TiO(2) particles, it can be concluded that the excitation is mainly of cyano character (i.e., on average, the dye molecules are standing on, and pointing out, from the surface of TiO(2) particles).     

Carbonated ferric green rust as a new material for efficient phosphate removal

Novel TiO(2)/carbon nanocomposites were prepared through the pyrolysis of TiO(2)/poly(furfuryl alcohol) hybrid materials, which were obtained by the sol-gel method, starting from titanium tetraisopropoxide (TTIP) and furfuryl alcohol (FA) precursors. Six different TiO(2)/C samples were prepared based on different TiO(2) nanoparticle sizes and TiO(2)/FA ratios. All of the samples were characterized using X-ray diffraction, infrared, and Raman spectroscopy. The results indicated effective FA polymerization onto the TiO(2) (anatase) nanoparticles, polymer conversion to disordered carbon following the pyrolysis, and a simultaneous TiO(2) anatase-rutile phase transition. The resulting TiO(2)/carbon composites were used as photocatalysts in the advanced oxidative process (AOP) for the degradation of reactive organic dyes in aqueous solution. The results indicate excellent photocatalytic performance (degradation of 99% of the dye after 60 min) with several advantages over traditional TiO(2)-based photocatalysts.     

Effect of chemical structure of interface modifier of TiO2 on photovoltaic properties of poly(3-hexylthiophene)/TiO2 layered solar cells

Two classes of phosphonic acid-bearing organic molecules, 2-oligothiophene phosphonic acid and omega-(2-thienyl)alkyl phosphonic acid were adopted as interface modifiers (IMs) of the TiO(2) surface, to increase its compatibility with poly(3-hexylthiophene) (P3HT). The self-assembled monolayers of these molecules on titania surface were characterized by making contact angle measurements and X-ray photoelectron spectroscopy (XPS). Atomic force microscopic (AFM) images revealed that the adsorption of IMs effectively smooths the TiO(2) surface. Both photoluminescence (PL) spectroscopy and PL lifetime measurements were made to investigate the photoinduced properties of the TiO(2)/IM/P3HT layered-junction. The PL quenching efficiency increased with the number of thiophene rings and as the alkyl chain-length in IMs decreased. Meanwhile, the decline in the PL lifetime followed a similar trend as the PL quenching efficiency. Additionally, the power conversion efficiency (PCE) of the ITO/TiO(2)/IM/P3HT/Au devices was examined by measuring their photocurrent density-applied voltage (J-V) curves. The experimental results indicated that the short-circuit current density (J(SC)) increased with the number of thiophene units and as the hydrocarbon chain-length in IMs decreased. However, the open-circuit voltage (V(OC)) of the devices slightly fell as the energy level of the highest occupied molecular orbital (HOMO) of IM decreased. The PCE of the device with 2-terthiophene phosphonic acid was 2.5 times that of the device with 10-(2-thienyl)decyl phosphonic acid.     

The importance of dye chemistry and TiCl(4) surface treatment in the behavior of Al(2)O(3) recombination barrier layers deposited by atomic layer deposition in solid-state dye-sensitized solar cells

Atomic layer deposition (ALD) was used to fabricate Al(2)O(3) recombination barriers in solid-state dye-sensitized solar cells (ss-DSSCs) employing an organic hole transport material (HTM) for the first time. Al(2)O(3) recombination barriers of varying thickness were incorporated into efficient ss-DSSCs utilizing the Z907 dye adsorbed onto a 2 μm-thick nanoporous TiO(2) active layer and the HTM spiro-OMeTAD. The impact of Al(2)O(3) barriers was also studied in devices employing different dyes, with increased active layer thicknesses, and with substrates that did not undergo the TiCl(4) surface treatment. In all instances, electron lifetimes (as determined by transient photovoltage measurements) increased and dark current was suppressed after Al(2)O(3) deposition. However, only when the TiCl(4) treatment was eliminated did device efficiency increase; in all other instances efficiency decreased due to a drop in short-circuit current. These results are attributed in the former case to the similar effects of Al(2)O(3) ALD and the TiCl(4) surface treatment whereas the insulating properties of Al(2)O(3) hinder charge injection and lead to current loss in TiCl(4)-treated devices. The impact of Al(2)O(3) barrier layers was unaffected by doubling the active layer thickness or using an alternative ruthenium dye, but a metal-free donor-π-acceptor dye exhibited a much smaller decrease in current due to its higher excited state energy. We develop a model employing prior research on Al(2)O(3) growth and dye kinetics that successfully predicts the reduction in device current as a function of ALD cycles and is extendable to different dye-barrier systems.     

Correlating interface heterostructure, charge recombination, and device efficiency of poly(3-hexyl thiophene)/TiO2 nanorod solar cell

The charge recombination rate in poly(3-hexyl thiophene)/TiO(2) nanorod solar cells is demonstrated to correlate to the morphology of the bulk heterojunction (BHJ) and the interfacial properties between poly(3-hexyl thiophene) (P3HT) and TiO(2). The recombination resistance is obtained in P3HT/TiO(2) nanorod devices by impedance spectroscopy. Surface morphology and phase separation of the bulk heterojunction are characterized by atomic force microscopy (AFM). The surface charge of bulk heterojunction is investigated by Kelvin probe force microscopy (KPFM). Lower charge recombination rate and lifetime have been observed for the charge carriers in appropriate heterostructures of hybrid P3HT/TiO(2) nanorod processed via high boiling point solvent and made of high molecular weight P3HT. Additionally, through surface modification on TiO(2) nan,orod, decreased recombination rate and longer charge carrier lifetime are obtained owing to creation of a barrier between the donor phases (P3HT) and the acceptor phases (TiO(2)). The effect of the film morphology of hybrid and interfacial properties on charge carrier recombination finally leads to different outcome of photovoltaic I-V characteristics. The BHJ fabricated from dye-modified TiO(2) blended with P3HT exhibits 2.6 times increase in power conversion efficiency due to the decrease of recombination rate by almost 2 orders of magnitude as compared with the BHJ made with unmodified TiO(2). In addition, the interface heterostructure, charge lifetime, and device efficiency of P3HT/TiO(2) nanorod solar cells are correlated.     

Kinetics of electron recombination of dye-sensitized solar cells based on TiO2 nanorod arrays sensitized with different dyes

The performance and electron recombination kinetics of dye-sensitized solar cells based on TiO(2) films consisting of one-dimensional nanorod arrays (NR-DSSCs) which are sensitized with dyes N719, C218 and D205, respectively, have been studied. It has been found that the best efficiency is obtained with the dye C218 based NR-DSSCs, benefiting from a 40% higher short-circuit photocurrent density. However, the open circuit photovoltage of the N719 based cell is 40 mV higher than that of the organic dye C218 and D205 based devices. Investigation of the electron recombination kinetics of the NR-DSSCs has revealed that the effective electron lifetime, τ(n), of the different dye based NR-DSSCs shows the sequence of C218 > D205 > N719. The higher V(oc) with the N719 based NR-DSSC is originated from the more negative energy level of the conduction band of the TiO(2) film. In addition, in comparison to the DSSCs with the conventional nanocrystalline particles based TiO(2) films, the NR-DSSCs have shown over two orders of magnitude higher τ(n) when employing N719 as the sensitizer. Nevertheless, the τ(n) of the DSSCs with the C218 based nanorod arrays is only ten-fold higher than that of the nanoparticles based devices. The remarkable characteristic of the dye C218 in suppressing the electron recombination of DSSCs is discussed.     

Mg(OOCCH(3))(2) as an electrolyte additive for quasi-solid dye-sensitized solar cells: with the purpose of enhancing both the photovoltage and photocurrent by modifying the TiO(2)/dye/electrolyte interfaces

The interface modification effect within quasi-solid dye-sensitized solar cells and the photovoltaic performance were investigated after the introduction of Mg(OOCCH(3))(2) as an additive into a polymer gel electrolyte. Electrochemical impedance spectroscopy showed that the addition of Mg(OOCCH(3))(2) into the polymer gel electrolyte can efficiently retard charge recombination at the TiO(2)/electrolyte interface. Mg(OOCCH(3))(2) in the electrolyte can also contribute to the enhancement of the incident photon-to-electron conversion efficiency by modifying the dye molecules. This results in an improvement in the photovoltage and photocurrent due to a barrier layer at the TiO(2)/electrolyte interface and the promotion of charge injection at the dye/TiO(2) interface, respectively. Photovoltaic measurements reveal that a conversion efficiency enhancement from 4.05% to 4.96% under 100 mW cm(-2) is obtained after the amount of Mg(OOCCH(3))(2) added was optimized.     

A Computational and Experimental Study of Thieno[3,4‐b]thiophene as a Proaromatic π‐Bridge in Dye‐Sensitized Solar Cells

Four D ‐π‐A dyes (D=donor, A=accpetor) based on a 3,4‐thienothiophene π‐bridge were synthesized for use in dye‐sensitized solar cells (DSCs). The proaromatic building block 3,4‐thienothiophene is incorporated to stabilize dye excited‐state oxidation potentials. This lowering of the excited‐state energy levels allows for deeper absorption into the NIR region with relatively low molecular weight dyes. The influence of proaromatic functionality is probed through a computational analysis of optimized bond lengths and nucleus independent chemical shifts (NICS) for both the ground‐ and excited‐ states. To avoid a necessary lowering of the TiO₂ semiconductor conduction band (CB) to promote efficient dye–TiO₂ electron injection, strong donor functionalities based on triaryl‐ and diarylamines are employed in the dye designs to raise both the ground‐ and excited‐state oxidation potentials of the dyes. Solubility, aggregation, and TiO₂ surface protection are addressed by examining an ethylhexyl alkyl chain in comparison to a simple ethyl chain on the 3,4‐thienothiophene bridge. Power conversion efficiencies of up to 7.8 % are observed.     

Enhanced Charge Separation Efficiency in Pyridine‐Anchored Phthalocyanine‐Sensitized Solar Cells by Linker Elongation

A series of zinc phthalocyanine sensitizers ( PcS22 – 24 ) having a pyridine anchoring group are designed and synthesized to investigate the structural dependence on performance in dye‐sensitized solar cells. The pyridine‐anchor zinc phthalocyanine sensitizer PcS23 shows 79 % incident‐photon to current‐conversion efficiency (IPCE) and 6.1 % energy conversion efficiency, which are comparable with similar phthalocyanine dyes having a carboxylic acid anchoring group. Based on DFT calculations, the high IPCE is attributed with the mixture of an excited‐state molecular orbital of the sensitizer and the orbitals of TiO₂. Between pyridine and carboxylic acid anchor dyes, opposite trends are observed in the linker‐length dependence of the IPCE. The red‐absorbing PcS23 is applied for co‐sensitization with a carboxyl‐anchor organic dye D131 that has a complementary spectral response. The site‐selective adsorption of PcS23 and D131 on the TiO₂ surface results in a panchromatic photocurrent response for the whole visible‐light region of sun light.     

Phthalocyanines: colorful macroheterocyclic sensitizers for dye-sensitized solar cells

Abstract  

Dye-sensitized solar cells (DSSCs) have gained great attention as lower-cost alternatives to conventional photovoltaic devices. One way to improve the excellent efficiencies (ca. 11%) exhibited by DSSCs based on ruthenium polypyridyl dyes would consist in using sensitizers with enhanced light-harvesting properties in the red region of the spectrum. Phthalocyanines (Pcs) are very robust molecules which present extraordinary high extinction coefficients in the 600- to 700-nm spectral region. Intensive research has been focused on reducing the undesired aggregation phenomena of Pcs on the metal oxide surface, while keeping a good electronic coupling between the LUMO of the Pcs and the TiO₂ conduction band, and a good solubility of the dye in organic solvents. Recently, unsymmetrically substituted “push–pull” Pcs have emerged as efficient red-absorbing dyes, reaching power conversion efficiencies of up to 4.7%, when used as single sensitizers.