Application of argon as the internal standard method in glow discharge mass spectrometry

Using (78)Ar(2)(+) as the internal standard (argon internal standard) in glow discharge mass spectrometry (GDMS) was investigated in detail. After comparing ion intensities and interferences, i.e. of argon ions, bi-atom argon ions and tri-atom argon ions, the (78)Ar(2)(+) was selected as the internal standard in the analysis. Mass spectral behavior of the argon internal standard affected by glow discharge current and voltage were studied. The ion intensity relationship between the argon internal standard and the matrix internal standard showed that the argon internal standard and the matrix internal standard have the same corrective effect on sample analysis. The experiment proved that the effects of the difference in analysis samples and the fluctuation of discharge conditions for analytical results were efficiently reduced if the argon internal standard was used. Moreover, the argon internal standard is similar to the matrix internal standard in correcting analytical results and both give satisfactory results. Elemental content in samples can be accurately determined by using the argon internal standard when the matrix content is unknown with good results.     

Quantification of residual monomer in polylactide by gas chromatographic internal standard method

An analytical method has been developed to quantitatively determine the residual lactide monomer in polylactide (PLA) using an internal standard method of gas chromatography (GC). The experimental results showed that diphenyl ether (DPE) was an appropriate internal standard for quantitative analysis of residual lactide in PLA. PLA and DPE were dissolved in dichloromethane and precipitated in hexane. At the same time, the residual lactide in PLA and DPE as an internal standard were extracted to hexane from the polymer solution. The resulting solution could be directly injected into a GC system. Therefore, the residual lactide was determined quantitatively using an internal standard method of GC. This method is practical for measuring the residual lactide content in PLA. When the lactide content is 5.0%, the relative standard deviation (RSD) of the measurements is 1.7%, while RSD is 6.9% at the low level of 0.4%, which indicates that the method is sufficiently precise.     

Photon and proton activation analysis of iron and steel standards using the internal standard method coupled with the standard addition method

The internal standard method coupled with the standard addition method has been applied to photon activation analysis and proton activation analysis of minor elements and trace impurities in various types of iron and steel samples issued by the Iron and Steel Institute of Japan (ISIJ). Samples and standard addition samples were once dissolved to mix homogeneously, an internal standard and elements to be determined and solidified as a silica-gel to make a similar matrix composition and geometry. Cerium and yttrium were used as an internal standard in photon and proton activation, respectively. In photon activation, 20 MeV electron beam was used for bremsstrahlung irradiation to reduce matrix activity and nuclear interference reactions, and the results were compared with those of 30 MeV irradiation. In proton activation, iron was removed by the MIBK extraction method after dissolving samples to reduce the radioactivity of⁵⁶Co from iron via⁵⁶Fe(p,n)⁵⁶Co reaction. The results of proton and photon activation analysis were in good agreement with the standard values of ISIJ.     

Instrumental photon activation analysis of coal fly ashes using the internal standard method coupled with the standard addition method

Multielement determinations of coal fly ashes (NIST SRM-1633a and BCR CRM-38) have been carried out by instrumental photon activation analysis using 30 MeV bremsstrahlung and the internal standard method coupled with the standard addition method. In these determinations, some major and minor constituent elements in the samples were properly used as effective internal standards. As a result, it was demonstrated that concentrations of 18 elements were determined accurately and precisely. Furthermore, a similar multielement determination has also been examined using 20 MeV bremsstrahlung. In this case, it was proved that better results can be achieved, because all interfering reactions were eliminated completely.     

Accurate determination of arsenic in arsenobetaine standard solutions of BCR-626 and NMIJ CRM 7901-a by neutron activation analysis coupled with internal standard method

Neutron activation analysis (NAA) coupled with an internal standard method was applied for the determination of As in the certified reference material (CRM) of arsenobetaine (AB) standard solutions to verify their certified values. Gold was used as an internal standard to compensate for the difference of the neutron exposure in an irradiation capsule and to improve the sample-to-sample repeatability. Application of the internal standard method significantly improved linearity of the calibration curve up to 1 μg of As, too. The analytical reliability of the proposed method was evaluated by k₀-standardization NAA. The analytical results of As in AB standard solutions of BCR-626 and NMIJ CRM 7901-a were (499 ± 55) mg kg⁻¹ (k = 2) and (10.16 ± 0.15) mg kg⁻¹ (k = 2), respectively. These values were found to be 15-20% higher than the certified values. The between-bottle variation of BCR-626 was much larger than the expanded uncertainty of the certified value, although that of NMIJ CRM 7901-a was almost negligible.     

Instrumental photon activation analysis of soil samples using the internal standard method coupled with the standard addition method

Multielement determinations in the certified reference materials of soils (IAEA soil-5 and 7) have been studied fundamentally by instrumental photon activation analysis using the internal standard method coupled with the standard addition method. For the soil-5 sample, in the first place, the qualities of the comparative standards prepared by two processing methods were compared with each other. As a result, it was demonstrated that a highly accurate and precise multielement determination can be achieved easily by minor improvement in the processing method of the comparative standard to ensure homogeneity. The utility of this processing method for soil samples was proved further through a similar analysis in another soil sample (IAEA soil-7).     

内标法测定偏二甲肼中的杂质含量

偏二甲肼(Unsymmetrical D imethylhydrazine,UDMH)是液体火箭推进剂主体燃烧剂之一,它与硝基氧化剂等组成双组元液体推进剂作为火箭发动机的能量工质,被广泛应用于导弹、卫星及航天器的发射中。偏二甲肼中杂质含量水平对于保证火箭的顺利发射具有重要意义。在有关标准和技术规     

Simplification of determination method for standard materials using post-column reaction GC/FID

For the simple and fast preparation of highly reliable standard materials, a post-column reaction GC/FID system was developed and evaluated on the mixture of oxygen-containing organic compounds. The oxygen-containing organic compounds mixing solution were determined with the post-column reaction GC/FID system using n-dodecane as an internal calibration standard. Required value of relative expanded uncertainty as an original source of SI-traceable standard materials was within 1% and it aimed at this value as accuracy of the quantitative analysis. The results showed good agreement between the prepared concentrations and analytical values using post-column reaction GC/FID system. These results indicated that the post-column reaction GC/FID system would be used for getting SI-traceable values.     

Interpolation in the standard additions method

The standard additions method (SAM) has traditionally been performed by using extrapolation. This practice is suboptimal because predictions are affected by even slight departures of calibration points from a straight line. Despite this, most textbooks and papers in analytical chemistry still refer exclusively to extrapolation. In contrast, the use of interpolation is recommended in this paper as a way to get predictions on the central part of the regression line and thus minimize the bias in the prediction and the variance associated with the analytical result. Several scenarios were studied, with concentration errors simulated in different calibration solutions. It was found that translational effects due to variations at the central part of the calibration caused the lowest disturbances on the predicted concentrations. The differences between the interpolated and extrapolated predictions can be as large as ±30%. The confidence interval associated with the extrapolation result is wider than that due to interpolation by as much as 100%. It is shown that commonly used equations underestimate the correct confidence intervals. Both, absence of bias and improved precision, are of relevance in quality assurance, method validation and error propagation.     

17种酞酸酯类环境激素GC-EI-MS分析方法的建立

以17种酞酸酯类(Phthalic Acid Esters,PAEs)环境激素为目标物,选择苯甲酸苄基酯为内标物,优化了气相色谱的升温程序和质谱的离子化方式等分析条件,初步解析了PAEs和内标物的电子轰击离子源-质谱谱图,并确定了选择离子检测方式的特征碎片离子,建立了同时分析17种PAEs环境激素的GC-EI-MS SIM分析方法,并应用于水生植物海白菜样品的分析。     

An internal standard method for the determination of trace elements in cigarette tobacco by neutron activation analysis

An internal standard method has been applied for the determination of lanthanum, antimony, scandium, chromium, iron and cobalt in commercial cigarettes by neutron activation analysis using gold as an internal standard element. These trace elements were separated from irradiated samples by APDC (ammonium pyrrolidine dithiocarbamate)/Zeph (tetradecyl dimethyl benzyl ammonium chloride) coprecipitation, followed by direct gamma-counting of the separated precipitate using a Ge(Li) detector. Standard reference tobacco 1R1 prepared by the University of Kentucky was also analyzed by this procedure for the above 6 elements, the results of which were compared with literature values. Good results were obtained by the present method.     

Stripping voltammetry with the electrode material acting as a ‘built-in' internal standard

The oxidation peak of the bismuth layer of bismuth-film electrodes is used as an internal standard in anodic stripping voltammetry. Such use of the electrode material as a ‘built-in' internal standard simplifies the analytical protocol (as it obviates the need for an external standard or long calibration and standard additions procedures) while correcting for run-to-run variations due to uncertainties (e.g., changes in mass transport, surface area, or other variables). The new internal standard strategy relies on common in situ plated film electrodes, where the deposition of both the analyte and electrode material is subject to the same variations. Such one-step quantitation and improvements are illustrated for trace measurements of lead. The use of the intrinsic signal of the system for obtaining the concentration of the target analyte is unique not only for electroanalysis, but for analytical chemistry in general.     

Enhanced spectrophotometric determination of chromium (VI) with diphenylcarbazide using internal standard and derivative spectrophotometry

In the present work, erioglaucine A was applied as internal standard to enhanced spectrophotometric determination of chromium (VI) with diphenylcarbazide. The following procedure was used: (1) addition of internal standard and formation of ion pairs of Cr (VI) with benzyltributylammonium bromide (BTAB) (sample volume 100 ml), (2) extraction to 10 ml of methylene chloride, (3) evaporation in nitrogen stream, and (4) redissolution in a micro-volume with addition of diphenylcarbazide for color development (final volume 200 mul). The preconcentration factor achieved was about 400 and it was shown that, using internal standard, the analytical errors due to sample treatment were reduced. The analytical signals for chromium and internal standard were obtained at 591.30 and 653.50 nm from first derivative spectra, normalized against (1)D(653.50nm). The analytical characteristics evaluated were: detection limit = 0.06 mug l(-1), quantification limit = 0.19 mug l(-1), precision for 1 mug l(-1) 14.2%, and for 10 mug l(-1) 3.2%, correlation coefficient of linear regression was 0.9985. The proposed procedure was applied to determination of chromium (VI) in tap water. Total chromium was determined by electrothermal atomic absorption spectrometry, the recovery of hexavalent chromium added was then evaluated and compared with the results of the proposed procedure. In this experiment, good agreement was obtained between results obtained by the two methods.     

Chromatographic quantitation at losses of analyte during sample preparation. Application of the modified method of double internal standard

Known methods of quantitative chromatographic analysis (calibration, external standard, internal standard and standard addition) require the application of sample preparation techniques without significant losses of analytes. If this condition cannot be satisfied, the compensation of these losses should be provided. The modification of known method of quantitative chromatographic analysis (double internal standard), implying the addition of two homologues (previous and following) of target analytes as internal standards into initial samples is considered. This approach permits us to compensate significant losses both analytes and standards at all stages of sample preparation. The advantages of this method are demonstrated on the examples of liquid-liquid extraction, head space analysis (HSA), distillation of volatile compounds with volatile solvents (concentration in condensates) and evaporation of volatile solvents (concentrating in the residues of solvents). In all cases the application of two homologues as internal standards provides accurate results (the typical relative errors are within 1-6%) at the values of a factor of composition distortion of initial samples (K', the definition is suggested) from 0.2 up to 4. These results are in accordance with general relationships between variations in any physicochemical properties of organic compounds within homologous series. The single found exception was the evaporation of volatile solvents (the open phase transition process) when to get the results with relative errors not more then +10% requires the minimal changes in the composition of initial samples (K' values should not be more then approximately 1.5).     

Elemental analysis of vegetation samples by INAA internal standard method

Journal of Radioanalytical and Nuclear Chemistry - The application of comparator instrumental neutron activation analysis (INAA) combined with the internal standard method (ISM) was considered to...     

Application of internal standard for derivative-spectrophotometric determination of azinphos-methyl in commercial formulations

The use of an internal standard is proposed in this work for first derivative spectrophotometric determination of azinphos in formulations. Generally, the spectrophotometric procedure is simpler and less expensive than chromatographic techniques recommended for the analysis of pesticides. However, while determining the pesticide in commercial formulations the, many-fold dilution required for such sensitive detection is a serious source of analytical error. It is known that an internal standard (IS), if properly chosen, can help eliminate this type of problem. A mixture of acetophenone (used as an IS in the high performance liquid chromatography (HPLC) procedure) and the blue dye Erioglaucine (A) was applied for the determination of azinphos-methyl in commercial formulations. To ensure the best conditions for the zero-crossing technique, the composition of the mixture was optimized to obtain the zero value of the first derivative absorbance of the IS at a minimum of the azinphos-methyl first derivative absorbance. Also, at the maximum of the first derivative spectrum of the IS, the differential absorption signal of the analyte was negligible. Analytical characteristics for the first derivative spectrophotometric procedure proposed were evaluated (r(2) = 0.9998, detection limit = 0.043 mg, quantification limit = 0.143 mg) and the analytical results obtained (35.02 +/- 0.20% of azinphos-methyl in the formulation) were in good agreement with the results obtained using the official HPLC method (35.44 +/- 0.32%).     

Metrological effectiveness of an analytical method for volatile organic compounds standard materials using post-column reaction GC/FID system

The metrological effectiveness of an analytical method using the post-column reaction GC/FID system was evaluated. The SI-traceable certified reference material (CRM), the eight ester phthalates mixture standard solution, was used as a sample. We assigned specific value to n-eicosane and it was used as an internal standard. A known quantity of n-eicosane was added to the CRM, and the mixture was measured with the post-column reaction GC/FID system. Six phthalate esters were chromatographically separated and determined. The assigned values by our system are in good agreement with the certified values of the CRM, and the combined uncertainties of the measurements by the present system were better than those of the CRM. Our method is classified as a primary ratio method and the specific values of many organic compounds can be assigned very precisely by using a small number of reference materials. Also, the method can make it possible to avoid the purity determination of raw materials and directly to assign their specific values after the preparation of the standard mixture. Conclusively, this post-column reaction GC/FID system is very effective for the chemical metrology.     

An endogenous standard, radioisotopic ratio method in NAA

A derivative form of NAA is proposed which is based on the use of an endogenous internal standard of already known concentration in the sample. If a comparator with a known ratio of the determinand and endogenous standard are co-irradiated with the sample, the determinand concentration is derived in terms of the endogenous standard concentration and the activity ratios of the two induced nuclides in the sample and comparator. As well as eliminating the sample mass and greatly reducing errors caused by pulse pile-up and geometrical differences, it was shown that in the radiochemical mode, if the endogenous standard is chosen so that the induced activity is radioisotopic with that from the determinand, the radiochemical yield is also eliminated and the risk of non-achievement of isotopic exchange greatly reduced. The method is demonstrated with good results on reference materials for the determination of I, Mn and Ni. The advantages and disadvantages of this approach are discussed. It is suggested that it may be of application in quality control and in extending the range of certified elements in reference materials.     

Instrumental photon activation analysis of environmental materials using the internal standard method

In order to study effective applications of the photon activation analysis using the internal standard method, determinations of Cr, Co, Ni, Zn, As, Rb, Sr, Y, Zr, Nb, Sb, Cs, Ba, Ce and Pb in two marine sediments as environmental materials have been examined by the use of a personal computer-based gamma-ray spectrometer equipped with a micro-robot for sample changing. In these determinations, some major and minor constituent elements in the samples were properly used as effective internal standards to check the roles with each other. As a result, it was demonstrated that accurate and precise determinations of the above 15 elements were achieved efficiently and favourably.