Self-compliance multilevel storage characteristic in HfO_2-based device

In this paper, the self-compliance bipolar resistive switching characteristic of an HfO_2-based memory device with Ag/HfO_2/Au structure for multilevel storage is investigated. By applying a positive voltage, the dual-step set processes corresponding to three stable resistance states are observed in the device. The multilevel switching characteristics can still be observed after 48 hours. In addition, the resistance values of all the three states show negligible degradation over 104 s,which may be useful for the applications in nonvolatile multilevel storage.     

氧化钒薄膜的微结构及阻变特性研究

采用射频反应溅射法于室温下在Cu/Ti/SiO₂/Si基底上制备了氧化钒薄膜. X-射线衍射、X射线光电子能谱分析仪及原子力显微镜结果表明, 室温下制备的氧化钒薄膜除微弱的V₂O₅ (101)和V₂O₃ (110)峰外, 没有明显的结晶取向, 是VO₂, V₂O₅, V₂O₃及VO的混合相薄膜, 且薄膜表面颗粒大小均匀, 表面均方根粗糙度约为1 nm. 采用半导体参数分析仪对薄膜的电开关特性进行测试. 结果表明薄膜具有较低的开关电压(V_Set<1 V, V_Reset<-0.5 V), 并且具有稳定的可逆开关特性. 薄膜从低阻态转变为高阻态的电流(I_Reset)随限流的增大而增大.通过高低阻态时I-V对数曲线的拟合(高阻态斜率>1, 低阻态斜率=1), 认为Cu离子在薄膜中扩散形成的导电细丝是该体系发生电阻转变的主要机制. 关键词： 氧化钒薄膜 电阻开关 电阻式非挥发存储器 导电细丝     

基于Cu/SiO_x/Al结构的阻变存储器多值特性及机理的研究

采用氧化硅材料构建了Cu/SiOx/Al的三明治结构阻变存储器件.用半导体参数分析仪对其阻变特性进行测量,结果表明其具有明显的阻变特性,并且通过调节限制电流,得到了四个稳定的阻态,各相邻阻态的电阻比大于10,并且具有良好的数据保持能力.在不同温度条件下对各个阻态进行电学测试及拟合,明确了不同阻态的电子传输机理不尽相同:阻态1和阻态2为欧姆传导机制,阻态3为P-F(Pool-Frenkel)发射机制,阻态4为肖特基发射机制.根据电子传输机制,建立了铜细丝导电模型并对Cu/SiOx/Al阻变存储器件各个阻态的电致阻变机制进行解释.     

Ni/HfO_2/Pt阻变单元特性与机理的研究

研究了Ni/HfO2(10 nm)/Pt存储单元的阻变特性和机理.该器件具有forming-free的性质,还表现出与以往HfO2(3 nm)基器件不同的复杂的非极性阻变特性,并且具有较大的存储窗口值(105).存储单元的低阻态阻值不随单元面积改变,符合导电细丝阻变机理的特征.采用X射线光电子能谱仪分析器件处于低阻态时的阻变层HfO2薄膜的化学组分以及元素的化学态,结果表明,Ni/HfO2/Pt阻变存储器件处于低阻态时的导电细丝是由金属Ni导电细丝和氧空位导电细丝共同形成的.     

氧分压对Ni/HfO_x/TiN阻变存储单元阻变特性的影响

采用射频磁控溅射的方法,基于不同氧分压制备的氧化铪构建了Ni/HfO_x/TiN结构阻变存储单元.研究发现,随着氧分压的增加,薄膜表面粗糙度略有降低;另一方面,阻变单元功耗降低,循环耐受性能可达10~3次,且转变电压分布的一致性得到改善.结合电流-电压曲线线性拟合结果及外加温度测试探究了器件的转变机理,得出在低阻态的传导机理为欧姆传导机理,在高阻态的传导机理为肖特基发射机理,并根据氧空位导电细丝理论,对高低阻态的阻变机理进行了详细的理论分析.     

基于HfO2的阻变存储器中Ag导电细丝方向和浓度的第一性原理研究

采用基于密度泛函理论的第一性原理方法, 研究了基于HfO₂的阻变存储器中Ag 导电细丝浓度以及方向性. 通过计算Ag杂质5种方向模型的分波电荷态密度等势面图、形成能、 迁移势垒和分波电荷态密度最高等势面值, 发现[-111]方向最有利于Ag导电细丝的形成, 这对器件的开启电压、形成电压和开关比有很大影响. 本文基于最佳的[-111]导电细丝方向, 设计了4 种Ag 浓度结构. 计算4种Ag浓度结构的分波电荷态密度等势面图, 得出Ag浓度低于4.00 at.% 时晶胞结构中无导电细丝形成且无阻变现象. 当Ag浓度从4.00 at.%增加到4.95 at.% 时, 晶胞结构中发现有导电细丝形成, 表明Ag浓度高于4.00 at.%时, 晶胞中可以发生阻变现象. 然而, 通过进一步对比计算这两种晶胞结构中Ag的形成能、分波电荷态密度最高等势面值、总态密度与Ag的投影态密度发现, Ag浓度越大, 导电细丝却不稳定, 并且不利于提高阻变存储器的开关比. 本文的研究结果可为改善基于HfO₂的阻变存储器的性能提供一定理论指导.     

Interface‐engineered resistive memory using plasma‐modified electrode on polyimide substrate

In this study, we report a low power Ni/GeO_x /TiO_y /TaN resistive random access memory (RRAM) using plasma‐modified electrode. The low sub‐mA switching current, highly uniform switching cycles (only 4% variation for the set) and good high‐temperature current distribution at 125 °C are simultaneously achieved in this RRAM device. Such good performance can be ascribed to interface plasma treatment on TaN electrode where the resulting Ta–N ionic bond increases the oxidation resistance and reduces the oxygen vacancy concentration near TaN interface that is favorable to lower switching power and improve high‐temperature current distribution.

     

阻变存储器复合材料界面及电极性质研究

采用基于密度泛函理论的第一性原理对比研究了Cu（111）/HfO₂（001）,Cu（111）/HfO₂（010）,Cu（111）/HfO₂（100）三种复合材料界面模型的失配率、界面束缚能、电荷密度、电子局域函数以及差分电荷密度. 计算结果表明：Cu（111）/HfO₂（010）失配率最小,界面束缚能最大,界面体系相对最稳定;对比电荷密度及电子局域函数图显示,只有HfO₂（010）方向形成的复合材料体系出现了垂直Cu电极方向完整连通的电子通道,表明电子在此方向上具有局域性、连通性,与阻变存储器（RRAM）器件导通方向一致;差分电荷密度图显示,Cu（111）/HfO₂（010）复合材料体系界面处存在电荷密度分布重叠的现象,界面处有电子的相互转移、成键的存在;进一步计算了Cu（111）/HfO₂（010）体系距离界面不同位置的间隙Cu原子形成能,表明越靠近界面Cu原子越容易进入HfO₂ 体内,在外加电压下易发生电化学反应,从而导致Cu导电细丝的形成与断裂. 研究结果可为RRAM存储器的制备及性能的提高提供理论指导和设计工具. 关键词： 阻变存储器 复合材料 界面 电子通道     

Bipolar resistance switching in the fully transparent BaSnO_3-based memory device

The fully transparent indium-tin-oxide/BaSnO3/F-doped SnO2 devices that show a stable bipolar resistance switching effect are successfully fabricated. In addition to the transmittance being above 87% for visible light, an initial forming process is unnecessary for the production of transparent memory. Fittings to the current-voltage curves reveal the interfacial conduction in the devices. The first-principles calculation indicates that the oxygen vacancies in cubic BaSnO3 will form the defective energy level below the bottom of conduction band. The field-induced resistance change can be explained based on the change of the interracial Schottky barrier, due to the migration of oxygen vacancies in the vicinity of the interface. This work presents a candidate material BaSnO3 for the application of resistive random access memory to transparent electronics.     

Investigation of resistive switching behaviours in WO3-based RRAM devices

In this paper, a WO₃-based resistive random access memory device composed of a thin film of WO₃ sandwiched between a copper top and a platinum bottom electrodes is fabricated by electron beam evaporation at room temperature. The reproducible resistive switching, low power consumption, multilevel storage possibility, and good data retention characteristics demonstrate that the Cu/WO₃/Pt memory device is very promising for future nonvolatile memory applications. The formation and rupture of localised conductive filaments is suggested to be responsible for the observed resistive switching behaviours.     

Resistive switching characteristic and uniformity of low-power HfO_x-based resistive random access memory with the BN insertion layer

In this letter,the Ta/HfO_x/BN/TiN resistive switching devices are fabricated and they exhibit low power consumption and high uniformity each.The reset current is reduced for the HfO_x/BN bilayer device compared with that for the Ta/HfO_x/TiN structure.Furthermore,the reset current decreases with increasing BN thickness.The HfO_x layer is a dominating switching layer,while the low-permittivity and high-resistivity BN layer acts as a barrier of electrons injection into TiN electrode.The current conduction mechanism of low resistance state in the HfO_x/BN bilayer device is space-chargelimited current(SCLC),while it is Ohmic conduction in the HfO_x device.     

Analysis of the resistive switching behaviors of vanadium oxide thin film

We demonstrate the polarization of resistive switching for a Cu/VOx/Cu memory cell.The switching behaviors of Cu/VOx/Cu cell are tested by using a semiconductor device analyzer(Agilent B1500A),and the relative micro-analysis of I-V characteristics of VOx/Cu is characterized by using a conductive atomic force microscope(CAFM).The I-V test results indicate that both the forming and the reversible resistive switching between low resistance state(LRS) and high resistance state(HRS) can be observed under either positive or negative sweep.The CAFM images for LRS and HRS directly exhibit evidence for the formation and rupture of filaments based on positive or negative voltage.The Cu/VOx/Cu sandwiched structure exhibits reversible resistive switching behavior and shows potential applications in the next generation of nonvolatile memory.     

Thermal effect on endurance performance of 3-dimensional RRAM crossbar array

Three-dimensional(3D) crossbar array architecture is one of the leading candidates for future ultra-high density nonvolatile memory applications. To realize the technological potential, understanding the reliability mechanisms of the3 D RRAM array has become a field of intense research. In this work, the endurance performance of the 3D 1D1 R crossbar array under the thermal effect is investigated in terms of numerical simulation. It is revealed that the endurance performance of the 3D 1D1 R array would be seriously deteriorated under thermal effects as the feature size scales down to a relatively small value. A possible method to alleviate the thermal effects is provided and verified by numerical simulation.     

Thermal stability and data retention of resistive random access memory with HfO_x/ZnO double layers

As an industry accepted storage scheme, hafnium oxide(HfO_x) based resistive random access memory(RRAM)should further improve its thermal stability and data retention for practical applications. We therefore fabricated RRAMs with HfO_x/ZnO double-layer as the storage medium to study their thermal stability as well as data retention. The HfO_x/ZnO double-layer is capable of reversible bipolar switching under ultralow switching current( 3 μA) with a Schottky emission dominant conduction for the high resistance state and a Poole–Frenkel emission governed conduction for the low resistance state. Compared with a drastically increased switching current at 120℃ for the single HfO_x layer RRAM, the HfO_x/ZnO double-layer exhibits excellent thermal stability and maintains neglectful fluctuations in switching current at high temperatures(up to 180℃), which might be attributed to the increased Schottky barrier height to suppress current at high temperatures. Additionally, the HfO_x/ZnO double-layer exhibits 10-year data retention @85℃ that is helpful for the practical applications in RRAMs.     

Graphene resistive random memory — the promising memory device in next generation

Graphene-based resistive random access memory(GRRAM) has grasped researchers' attention due to its merits compared with ordinary RRAM. In this paper, we briefly review different types of GRRAMs. These GRRAMs can be divided into two categories: graphene RRAM and graphene oxide(GO)/reduced graphene oxide(r GO) RRAM. Using graphene as the electrode, GRRAM can own many good characteristics, such as low power consumption, higher density, transparency,SET voltage modulation, high uniformity, and so on. Graphene flakes sandwiched between two dielectric layers can lower the SET voltage and achieve multilevel switching. Moreover, the GRRAM with r GO and GO as the dielectric or electrode can be simply fabricated. Flexible and high performance RRAM and GO film can be modified by adding other materials layer or making a composite with polymer, nanoparticle, and 2D materials to further improve the performance. Above all,GRRAM shows huge potential to become the next generation memory.     

Forming‐free resistive switching characteristics and improved reliability in sub‐stoichiometric NbNx films

In this study, we demonstrate forming‐free and reliable resistive switching (RS) characteristics by controlling the stoichiometry of niobium nitride (NbN_x) films. Compared to a perfect stoichiometric NbN_x film, a decrease of 6% nitrogen content and an increase of 5% O₂ content are found in the sub‐stoichiometric NbN_x sample (s‐NbN_x), and a structural change for the s‐NbN_x film is observed from X‐ray diffraction results, which results in the possibility of abundant defect generation in the s‐NbN_x film at virgin state. In the RS test, the s‐NbN_x film normally carries out well without initial forming because of the already‐formed conducting filaments; in particular, in the reliability study, the s‐NbN_x film shows more stable dc cycling characteristics for 1000 cycles without any degradation and smaller variations in the operating current and voltage characteristics. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

阻变式存储器存储机理

阻变式存储器（resistive random access memory, RRAM）是以材料的电阻在外加电场作用下可在高阻态和低阻态之间实现可逆转换为基础的一类前瞻性下一代非挥发存储器.它具有在32nm节点及以下取代现有主流Flash存储器的潜力,成为目前新型存储器的一个重要研究方向.但阻变式存储器的电阴转变机理不明确,制约它的进一步研发与应用.文章对阻变式存储器的体材料中几种基本电荷输运机制进行了归纳,总结了目前对阻变式存储器存储机理的理论模型.     

利用加速器重离子进行SRAM单粒子效应研究

 报导了利用北京大学串列静电加速器提供的重离子对两类静态随机存储器进行单粒子效应的实验和测量。给出了两类静态随机存储器的单粒子效应翻转截面随线性能量转移值的变化关系曲线。