Vibrational spectroscopy of oxygen on the (100) and (111) surfaces of lanthanum hexaboride

Reflection absorption infrared spectroscopy (RAIRS) and high resolution electron energy loss spectroscopy (HREELS) have been used to study the adsorption of oxygen on the (100) and (111) surfaces of lanthanum hexaboride. Exposure of the surface at temperatures of 95 K and above to O₂ produces atomic oxygen on the surface and yields vibrational peaks in good agreement with those observed in previous HREELS studies. On the La-terminated (100) surface, RAIRS peaks correspond to vibrations of the boron lattice that gain intensity due to a decrease in screening of surface dipoles that accompanies oxygen adsorption. A sharp peak at ～ 734 cm^?1 in the HREEL spectrum shows isotopic splitting with RAIRS into two components at 717 and 740 cm^?1 with full widths at half maxima of only 12 cm^?1. The sharpness of this mode is consistent with its interpretation as a surface phonon that is well separated from both the bulk phonons and other surface phonons of LaB₆. On the boron-terminated LaB₆(111) surface, broad and weak features are assigned to both vibrations of the boron lattice and of boron oxide. On the (100) surface, oxygen blocks the adsorption sites for CO, and adsorbed CO prevents the dissociative adsorption of O₂.     

An investigation of the effect of pre-dosed O atoms on the adsorption of NO on Pt{2 1 1}

Reflection absorption infrared spectroscopy (RAIRS) and temperature programmed desorption (TPD) have been used to investigate the effect of pre-dosed O atoms on the adsorption of NO on Pt{2 1 1} at room temperature. RAIRS experiments show that no new species are formed when NO is adsorbed onto a Pt{2 1 1} surface that has been pre-dosed with oxygen and no species are lost from the spectra, compared to spectra recorded for NO adsorption on the clean Pt{2 1 1} surface. However pre-dosed oxygen atoms do influence the frequency and intensity of several of the observed infrared bands. In stark contrast, pre-dosed O has a large effect on the TPD spectra. In particular N₂ and N₂O desorption, seen following NO adsorption on the clean Pt{2 1 1} surface, is completely inhibited. This effect has been assigned to the blocking of NO dissociation by the pre-adsorbed O atoms. A new NO desorption peak, not seen for NO adsorption on the clean Pt{2 1 1} surface, is also observed in TPD spectra recorded following NO adsorption on an oxygen pre-dosed Pt{2 1 1} surface.     

Ab initio determination of atomic structure and energy of surface states of bare and hydrogen covered GaN (0001) surface — Existence of the Surface States Stark Effect (SSSE)

Density Functional Theory (DFT) calculations indicate that energetically stable structure of clean GaN(0001) surface posses (2 × 1) reconstruction, having every second row of Ga located near plane of N atoms, that gives rise to Ga-related dispersionless surface electronic state, already identified by angle resolved photoelectron spectroscopy (ARPES) measurements [S.S. Dhesi et al. Phys. Rev. B 56 (1997) 10271, L. Plucinski et al. Surf. Sci 507-10 (2002) 223, S. M. Widstrand et al. Surf. Sci. 584 (2005) 169]. The energy reduction in reconstruction proceeds via change of the hybridization of the occupied Ga surface states from sp³ to sp², transforming the empty states to p_z type. It is also shown that the electric subsurface field, modeled in new slab model which allows to simulate electric fields at the semiconductor surfaces [P. Kempisty et al., J. Appl. Phys. 106 (2009) 054901], strongly affects the energy of electronic states of GaN(0001) surfaces. The change of the field may shift the energy of surface states of bare and hydrogen covered GaN(0001) surface, by several eV with respect to the band states. The phenomenon, denoted as Surface States Stark Effect (SSSE), explains various band bending values, measured at differently doped n-type GaN(0001) surfaces. It is shown also that, for the adsorbate density up to one H atom for each Ga surface atom i.e. 1 monolayer coverage (1 ML), the hydrogen adatoms are located at the on-top positions, i.e. directly above Ga atoms. For these adsorbate densities, the H-related quantum surface state is located slightly below the valence band maximum (VBM) in the case of p-type GaN surface. For n-type GaN, the H-related surface state is located deeply in the valence band, about 2 eV below VBM. For higher, 1.25 ML hydrogen coverage, the two H adatoms create either surface attached H₂ ad-molecule (energetically stable) or triple bridge configuration is created (metastable). The H₂ ad-molecule is weekly attached to the surface, having the desorption energy barrier equal to 0.16 eV. For 1.25 ML coverage the DFT results were obtained for p-type GaN only. They show that in the ad-molecule case, a new surface electronic state arises which is located about 6.7 eV below VBM. In the case of the bridge configuration, the bridge related surface state is located closely to the conduction band minimum (CBM).     

Stability of small chemical groups on hexagonal-SiC(0001) surfaces: A theoretical study

Density functional theory (DFT) calculations are used to investigate the stability on SiC(0001) surfaces of different chemical groups -NH₂, -NO₂, -CH₃, -OH, -SH and -CN. The adsorption stability decreases in the order -NO₂ > ? OH > ? NH₂ > ? SH > ? CN > ? CH₃. The stability of the single molecule-substrate bond is strongly influenced by the polarizability, which in turn depends on different parameters such as the electronegativity, atomic size and chemical environment. In a further step, methyl (? ACH₃) and phenyl (? AC₆H₅) substituted groups are also considered and similar behaviour is observed. The inductive effect of the -CH₃ or -C₆H₅ groups modifies the polarization of the Si adatom-molecule bond and the steric hindrance due to their size influences the molecular orientation. These two parameters affect the calculated adsorption energy, and are more important for –C₆H₅ substituent. This study provides clear tendencies that can be applied to more complex systems. Comparison of the adsorption of two large molecules, H₂Pc (metal-free phthalocyanine) and PTCDI (perylene tetracarboxylic diimide) on the SiC(0001) surface is presented as an example.     

Adsorption and dissociation of water on LaB6(100) investigated by surface vibrational spectroscopy

The chemisorption of water (H₂O and D₂O) on a LaB₆(100) surface was studied with reflection absorption infrared spectroscopy (RAIRS) and high resolution electron energy loss spectroscopy (HREELS). The clean surface was exposed to H₂O and D₂O at temperatures from 90 K to room temperature, and spectra were acquired after heating to temperatures as high as 1200 K. It was found that water molecularly adsorbs on the surface at 90 K as a monomer at low coverages and as amorphous solid water at higher coverages. Water adsorbs dissociatively at room temperature to produce surface hydroxyl species as indicated by OH/OD stretch peaks at 3676/2701 cm^?1. Room temperature adsorption also reveals low frequency loss features in HREEL spectra near 300 cm^?1 that are quite similar to results obtained following the dissociative adsorption of O₂. In the latter case, the loss features were attributed to the LaO stretch of O atoms bridge-bonded between two La atoms. In the case of dissociative adsorption of H₂O, the low frequency loss features could be due to either the LaO vibrations of adsorbed O or of adsorbed OH.     

Effect of H2O chemisorption on passivation of Ge(100) surface studied by scanning tunneling microscopy

The electronic passivation of a Ge(100) surface, via the chemisorption of H₂O at room temperature (RT), and the temperature dependence of H₂O coverage were investigated using scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS). With a saturation H₂O dose at RT, a highly-ordered structure, due to the dissociative chemisorption of H₂O, was observed on a Ge(100) surface with a coverage of 0.85 monolayers (ML). Annealing the room temperature H₂O-dosed Ge surface to 175 °C decreased the coverage of H₂O to 0.6 ML. Further annealing at 250 °C decreased the coverage of H₂O sites to 0.15 ML, and the surface reconstruction of Ge dimers was observed over much of the surface. Annealing above 300 °C induced Ge suboxide structures, similar to the oxygen-dosed Ge surface. STS measurements confirmed that the surface dangling bond states near Fermi energy are removed by the H₂O chemisorption because the dangling bonds of Ge atoms are terminated by ―OH and ―H. The H₂O pre-dose at room temperature provides a template for the ultrathin passivation of Ge(100) surface via atomic layer deposition (ALD) at RT, since near monolayer nucleation can be obtained with a 1/2 hydroxylated and 1/2 hydrogenated Ge surface.     

Protonic mobility in acidic colloids

Colloidal monoclinic zirconia ZrO₂ particles have been synthesized by hydrothermal treatment from acetate solutions. To increase their surface acidity, they have been treated by aqueous solutions of phosphoric acid, sulfophenylphosphonic acid (SPPA, (HO)₂(O)–C₆H₆–SO₃H) and sulfodifluoromethylphosphonic acid (SFPA, (HO)₂(O)P–CF₂–SO₃H). This leads to the covalent bonding of phosphoric or sulfonic acid groups onto the surface of the particles. Solid state NMR (³¹P, ¹H) studies show the covalent grafting of the phosphate and phosphonates groups and qualitatively illustrate the fast proton dynamics of these surface conducting materials as compared with that of crystalline α-Zr(HPO₄)₂. H₂O. But, water adsorption is still necessary to increase the long distance proton mobility. Then, the macroscopic conductivity remains low (between 10^− 4 S cm^− 1 and 10^− 3 S cm^− 1 25 °C, RH 70%) and shows a strong hysteresis while cycling the relative humidity. The mechanism limiting the conductivity seems to be interparticle transfer.     

Low temperature oxidation of Fe2+ surface sites on the (2 × 1) reconstructed surface of α-Fe2O3(011­2)

Temperature programmed desorption (TPD), electron energy loss spectroscopy (ELS) and low energy electron diffraction (LEED) were used to study the interaction of molecular oxygen with the (2 × 1) reconstructed surface of hematite α-Fe₂O₃(011­2) under UHV conditions. The (2 × 1) surface is formed from vacuum annealing of the ‘ideal’ (1 × 1) surface and possesses Fe²⁺ surface sites based on ELS. While O₂ does not stick to the (1 × 1) surface at 120 K, the amount of O₂ that can be reversibly adsorbed at 120 K on the (2 × 1) surface was estimated to be ～ 0.5 ML (where 1 ML is defined as the Fe³⁺ surface coverage on the ideal (1 × 1) surface), with additional O₂ that is irreversibly adsorbed based on subsequent H₂O TPD. Molecularly and dissociatively adsorbed O₂ modifies the surface chemistry of H₂O both in terms of enhanced OH stability (relative to either the (1 × 1) or (2 × 1) surfaces) and in the blocking of H₂O adsorption sites. While O₂ adsorption at 120 to 300 K does not transform the (2 × 1) surface into the (1 × 1) surface, the influence of O₂ on the (2 × 1) surface involves both charge transfer from surface Fe²⁺ sites and formation of an ordered c(2 × 2) structure resulting from O₂ dissociation.     

Hydrogen adsorption on palladium and palladium hydride at 1 bar

The dissociative sticking probability for H₂ on Pd films supported on sputtered Highly Ordered Pyrolytic Graphite (HOPG) has been derived from measurements of the rate of the H–D exchange reaction at 1 bar. The sticking probability for H₂, S, is higher on Pd hydride than on Pd (a factor of 1.4 at 140 °C), but the apparent desorption energy derived from S is the same on Pd and Pd hydride within the uncertainty of the experiment. Density Functional Theory (DFT) calculations for the (1 1 1) surfaces of Pd and Pd hydride show that, at a surface H coverage of a full mono layer, H binds less strongly to Pd hydride than to Pd. The activation barrier for desorption at a H coverage of one mono layer is slightly lower on Pd hydride, whereas the activation energy for adsorption is similar on Pd and Pd hydride. It is concluded that the higher sticking probability on Pd hydride is most likely caused by a slightly lower equilibrium coverage of H, which is a consequence of the lower heat of adsorption for H on Pd hydride.     

The structure and extinction of nonpremixed methane/nitrous oxide and ethane/nitrous oxide flames

Knowledge of combustion of hydrocarbon fuels with nitrogen-containing oxidizers is a first step in understanding key aspects of combustion of hypergolic and gun propellants. Here an experimental and kinetic-modeling study is carried out to elucidate aspects of nonpremixed combustion of methane (CH₄) and nitrous oxide (N₂O), and ethane (C₂H₆) and N₂O. Experiments are conducted, at a pressure of 1 atm, on flames stabilized between two opposing streams. One stream is a mixture of oxygen (O₂), nitrogen (N₂), and N₂O, and the other a mixture of CH₄ and N₂ or C₂H₆ and N₂. Critical conditions for extinction are measured. Kinetic-modeling studies are performed with the San Diego Mechanism. Experimental data and results of kinetic-modeling show that N₂O inhibits the flame by promoting extinction. Analysis of the flame structure shows that H radicals are produced in the overall chain-branching step 3H₂ + O₂ ? 2H₂O + 2H, in which molecular hydrogen is consumed. Hydrogen is also consumed in the overall step N₂O + H₂ ? N₂ + H₂O where stable products are formed. Inhibition of the flames by N₂O is attributed to competition between these two overall steps.     

Interaction of atomic H and CO with Cu(1 1 0) and bimetallic Ni/Cu(1 1 0)

Co-adsorption of hydrogen and CO on Cu(1 1 0) and on a bimetallic Ni/Cu(1 1 0) surface was studied by thermal desorption spectroscopy. Hydrogen was exposed in atomic form as generated in a hot tungsten tube. The Ni/Cu surface alloy was prepared by physical vapor deposition of nickel. It turned out that extended exposure of atomic hydrogen leads not only to adsorption at surface and sub-surface sites, but also to a roughening of the Cu(1 1 0) surface, which results in a decrease of the desorption temperature for surface hydrogen. Exposure of a CO saturated Cu(1 1 0) surface to atomic H leads to a removal of the more strongly bonded on-top CO (α₁ peak) only, whereas the more weakly adsorbed CO molecules in the pseudo threefold hollow sites (α₂ peak) are hardly influenced. No reaction between CO and H could be observed. The modification of the Cu(1 1 0) surface with Ni has a strong influence on CO adsorption, leading to three new, distinct desorption peaks, but has little influence on hydrogen desorption. Co-adsorption of H and CO on the Ni/Cu(1 1 0) bimetallic surface leads to desorption of CO and H₂ in the same temperature regime, but again no reaction between the two species is observed.     

First principles total energy calculations of the adsorption of germane and digermane on Si(0 0 1)-c(2 × 4)

First principles total energy studies are performed to investigate the energetics, and the atomic structure of the adsorption of germane (GeH₄), and digermane (Ge₂H₆) on the Si(0 0 1)-c(2 × 4) surface. It has been observed experimentally that adsorption of Ge₂H₆ is a dissociative process, which first yields GeH₃ and then GeH₂ fragments as products. We first study the adsorption of GeH₂ considering two different models; the intra-row and the on-dimer geometries. Our results show that the on-dimer site is more stable than the intra-row geometry by 0.44 eV. This is not a surprise since in the absence of H atoms, adsorption in the on-dimer site leaves no dangling bonds. In contrast, when the GeH₂ fragment is considered together with two H atoms, the intra-row geometry is favored energetically as compared with the on-dimer site, in good agreement with experiment. Similar results have been previously obtained for the adsorption of SiH₂ on Si(0 0 1). Digermane adsorption is explored according to two different geometries. In the first one, we have considered the adsorption as two GeH₃ fragments, while in the second, we have considered the adsorption as two GeH₂ fragments plus 2 H fragments. In good agreement with experiments, it is found that the latter geometry is energetically more favorable.     

Silver sulphide growth on Ag(111): A medium energy ion scattering study

The interaction of S₂ with Ag(111) under ultra-high vacuum conditions has been investigated by medium energy ion scattering (MEIS). 100 keV He⁺ MEIS measurements provide a direct confirmation of a previous report, based on thermal desorption, that the growth of multilayer films of Ag₂S occurs through a continuous corrosion process. These films show a commensurate (√7 × √7)R19° unit mesh in low energy electron diffraction, consistent with the epitaxial growth of (111) layers of the high-temperature F-cubic phase of Ag₂S. The substantial range of co-existing film thicknesses found indicates that the growth must be in the form of variable-thickness islands. The use of 100 keV H⁺ incident ions leads to a very rapid decrease in the sulphide film thickness with increasing exposure that we attribute to an unusual chemical leaching, with implanted H atoms interacting with S atoms and desorption of H₂S from the surface.     

Proton transfer in water–hydroxyl mixed overlayers on Pt(1 1 1): Combined approach of laser desorption and spatially-resolved X-ray photoelectron spectroscopy

Proton transfer in water–hydroxyl mixed overlayers on a Pt(1 1 1) surface was studied by a combination of laser induced thermal desorption (LITD) method and spatially-resolved X-ray photoelectron spectroscopy (micro-XPS). The modulated pattern OH + H₂O/H₂O/OH + H₂O was initially prepared by the LITD method; vacant area with a 400 μm width was first formed in the mixed OH + H₂O overlayer by irradiation of focused laser pulses, and followed by refilling the vacant area with pure H₂O. Spatial distribution changes of OH and H₂O were measured as a function of time with the micro-XPS technique, which indicated that H₂O molecules in the central region flow into the OH + H₂O region. From quantitative analyses using a diffusion equation, we found that the proton transfer in the mixed overlayer consists of at least two pathways: direct proton transfer from H₂O to OH in the nearest site and the proton transfer to the next-nearest site via H₃O⁺ formation. The time scale of first and second path was estimated to be 5.2 ± 0.9 ns and 48 ± 12 ns at 140 K, respectively. In the presence of water capping layer, however, the rate of proton transfer is reduced by an order of magnitude, which would be explained by peripatetic behavior of proton into H₂O capping layer.     

Highly sensitive hydrogen detection by medium energy Ne+ impact

Hydrogen atoms on solid surfaces were measured directly by elastic recoil detection analysis (ERDA) using medium energy (100–150 keV) Ne⁺ ions with an excellent sensitivity of (～ 1 × 10¹² H/cm²) without any absorber foils and time-of-flight techniques. An electrostatic toroidal analyzer acquired H⁺ ions with energy around 11 keV recoiled from Si(111)-1 × 1-H surfaces. The H⁺ fraction strongly depends upon emerging angle and takes a value more than 50% at the angle below 70° and a saturated value of 17% at the angle above 80° with respect to surface normal. We detected H atoms on the reduced TiO₂(110) exposed to water molecules at room temperature (2 L) and estimated the absolute amount of H to be ～ 2.0 × 10¹⁴ H/cm² corresponding to ～ 38% (～ 0.38 ML) of the bridging oxygen atoms.     

Interaction of hydrogen with (2 1 0)-oriented metal surfaces: Molecular precursors,chemisorbed atoms and subsurface states

Some selected aspects of hydrogen interaction with metal surfaces are surveyed with emphasis on the formation of molecular precursor states on surfaces that are normally known to readily and spontaneously dissociate hydrogen molecules (Ni, Pd, Rh). We will demonstrate that the crystallographic (2 1 0) orientation of the face-centered cubic (“f.c.c”) lattice seems to provide a particular route for stabilizing a (weakly) chemisorbed H₂ species notwithstanding the ordinary H₂ dissociative chemisorption and – in the Pd case – subsurface H state formation. This molecular hydrogen species – although or just because it is bound with an adsorption energy of merely ～20–25 kJ/mole may play an essential role both in heterogeneously catalysed surface and hydrogen uptake reactions that precede, e.g., H storage in solid materials.     

Surface modification of Ni and Co metal nanowires through MeV high energy ion irradiation

Nickel (Ni) and cobalt (Co) metal nanowires were fabricated by using an electrochemical deposition method based on an anodic alumina oxide (Al₂O₃) nanoporous template. The electrolyte consisted of NiSO₄ · 6H₂O and H₃BO₃ in distilled water for the fabrication of Ni nanowires, and of CoSO₄ · 7H₂O with H₃BO₃ in distilled water for the fabrication of the Co ones. From SEM and TEM images, the diameter and length of both the Ni and Co nanowires were measured to be ∼ 200 nm and 5–10 μm, respectively. We observed the oxidation layers in nanometer scale on the surface of the Ni and Co nanowires through HR–TEM images. The 3 MeV Cl²⁺ ions were irradiated onto the Ni and Co nanowires with a dose of 1 × 10¹⁵ ions/cm². The surface morphologies of the pristine and the 3 MeV Cl²⁺ ion-irradiated Ni and Co nanowires were compared by means of SEM, AFM, and HR–TEM experiments. The atomic concentrations of the pristine and the 3 MeV Cl²⁺ ion-irradiated Ni and Co nanowires were investigated through XPS experiments. From the results of the HR–TEM and XPS experiments, we observed that the oxidation layers on the surface of the Ni and Co nanowires were reduced through 3 MeV Cl²⁺ ion irradiation.     

Visible light induced photodesorption of NO from the α-Cr2O3(0001) surface

Nitric oxide chemistry and photochemistry on the Cr-terminated surface of α-Cr₂O₃(0001) were examined using temperature programmed desorption (TPD), sticking coefficient measurements and photodesorption. NO exposed to α-Cr₂O₃(0001) at 100 K binds at surface Cr cation sites forming a strongly bound surface species that thermally desorbs at 320–340 K, depending on coverage. No thermal decomposition was detected in TPD in agreement with previous results in the literature. Sticking probability measurements at 100 K indicated near unity sticking for NO up to coverages of ~ 1.3 ML, with additional adsorption with higher exposures at decreased sticking probability. These results suggest that some Cr cation sites on the α-Cr₂O₃(0001) surface were capable of binding more than one NO molecule, although it is unclear whether this was as separate NO molecules or as dimers. Photodesorption of adsorbed NO was examined for surface coverages below the 1 ML point. Both visible and UV light were shown to photodesorb NO without detectable NO photodecomposition. Visible light photodesorption of NO occurred with a greater cross section than estimated using UV light. The visible light photodesorption event was not associated with bandgap excitation in α-Cr₂O₃(0001), but instead was linked to excitation of a surface Cr^3 +–NO^? charge transfer complex. These results illustrate that localized photoabsorption events at surface sites with unique optical properties (relative to the bulk) can result in unexpected surface photochemistry.     

On the stability of the CO adsorption-induced and self-organized CuPt surface alloy

The stability of the recently discovered CO-induced and self-organized CuPt surface alloy was explored at near ambient pressures of O₂ (200 mbar) at room temperature, in a CO + H₂ mix (P_tot = 220 mbar, 4% CO) from room temperature to 573 K, as well as in a CO + H₂O mix (P_tot = 17 mbar, 50% CO) from room temperature to 673 K. No indications of substantial changes in surface structure were observed under the latter conditions compared to CO alone whereas the O₂ oxidation resulted in CO removal and the build-up of an ultrathin CuO_x-film. However, the oxidized CO/CuPt surface alloy could be regenerated by reducing the CuO_x in 100 mbar CO for 10 min at room temperature. The results show, amongst others, the stability of the CuPt surface alloy in various environments containing CO and how a novel coinage/Pt-group bimetallic surface alloy catalyst induced by CO adsorption can be reactivated before use in applications such as electrochemistry at ambient temperatures.