稀土Ce掺杂对ZnO结构和光催化性能的影响

采用共沉淀-焙烧法合成了一系列不同含量的稀土Ce掺杂的ZnO光催化剂. 利用傅里叶变换红外(FT-IR)光谱、粉末X射线衍射(XRD)、扫描电镜(SEM)、紫外-可见(UV-Vis)光谱、光致发光(PL)谱等技术对所制备的光催化剂进行了系列表征. 以酸性橙II脱色降解为模型反应, 考察了掺杂不同含量的铈及不同焙烧温度对ZnO的物理结构和光催化脱色性能的影响. 结果表明: 掺入质量分数(w)为2%的铈可以明显改善氧化锌表面状态, 有利于产生更多的表面羟基; 同时可以抑制光生电子与光生空穴(e^-/h⁺)的复合, 显著提高光催化脱色活性和光催化稳定性; 焙烧温度对光催化剂的晶体结构、表面性能和光催化活性产生较大影响, 500 °C的焙烧处理使样品的结晶度较高, 同时催化剂颗粒粒径较细, 表面具有丰富的羟基. 但过高的焙烧温度(600-800 °C)将导致催化剂的物理结构发生恶化, 降低光催化性能.     

铈掺杂WO3的表征及其光解水催化性能的研究

采用固相烧结法制备了掺杂不同量铈的WO₃催化材料，并用XRD，XPS，DRS和PL光谱对样品进行了表征，主要考察了铈含量和焙烧温度对WO₃的性质及光催化分解水制氧活性的影响，初步探讨了样品的PL光谱与其光催化分解水制氧活性的关系。结果表明，铈的掺杂可以使WO₃的光谱响应范围向可见光区拓展。铈的掺杂没有引发新的荧光现象，适量铈的掺杂能够增强催化剂样品的荧光强度。在可见光辐射下进行光催化分解水制氧，于600 ℃处理的掺杂铈为0.05%(wt)的WO₃催化剂的催化活性最高，此时催化剂的析氧速率比未掺杂WO₃提高了1.5～1.7倍。研究表明，样品的光催化活性与其PL信号强度顺序一致，即PL信号越强，光催化活性越高。     

CoOx改性TiO2光催化剂的制备、优化及其光催化分解水析氢性能研究

利用热分解法制备了不同掺杂量的CoO_x-TiO₂系列光催化剂, 并优化了制备方法。在用XRD、TEM和XPS等技术对催化剂表征的基础上，探讨了乙醇作为电子给体时CoO_x改性对P25-TiO₂光催化分解水析氢性能的影响。本文还利用连续瞬态电流-时间响应和循环伏安法等电化学方法，考察了CoO_x-TiO₂改性系列光催化剂光照条件下电流响应强度、起始光电响应特性差别及光催化析氢电位变化等光电化学性能。光催化性能实验结果表明，适当掺杂CoO_x(110～400 ℃焙烧时最佳掺杂量约为0.4wt% Co，500 ℃焙烧时最佳掺杂量约为0.6～0.8wt% Co)能够显著地提高TiO₂析氢光催化性能，产氢速率提高2个数量级。另外在适当温度下的热处理，能够改善催化剂光催化性能(最佳处理温度为300～400 ℃)。光电化学性能评价结果表明，适当掺杂CoO_x和适当温度下焙烧能在催化剂表面形成较多的析氢活性物种——含钴复合物，能有效增强催化剂光电流响应强度，并使得析氢光还原电位向有利于析氢方向位移。高含量掺杂CoO_x会在催化剂表面形成某种碳化物物种，大量含钴复合物活性中心的出现会降低光吸收效率，增加TiO₂表面光生电子-空穴复合率而使催化剂失去析氢光催化性能。     

模板法制备的Fe3+/TiO2中空纳米纤维的光催化性能

以棉花纤维为模板,利用浸渍-热转化两步法制备了Fe³⁺掺杂的二氧化钛(Fe³⁺/TiO₂)中空纳米纤维光催化材料,并利用扫描电镜(SEM)、X射线衍射(XRD)、紫外-可见光谱(UV-Vis)和ζ电位等技术对其形貌、结构、光吸收特性及其表面状态等进行了表征。以亚甲基蓝(methylene blue,MB)溶液的脱色降解为模型反应,考察了煅烧温度与时间对Fe³⁺/TiO₂中空纳米纤维光催化性能的影响。结果表明：利用该法可以制得棉花纤维形貌的Fe³⁺/TiO₂中空纳米结构材料;所得材料的催化性能除与材料的尺寸、相结构有关外,还与表面荷电性质有关,表面荷电量越高、表面结构缺陷越多、表面活性位越多,催化活性越高。500 ℃下煅烧2 h所得材料表面长有大量的粒子(平均尺寸为12 nm),其中TiO₂为锐钛矿结构,表面荷负电荷量最高,催化性能最好,如在太阳光下,2 h可使MB溶液的脱色降解率达93%,6 h完全脱色,而在纯TiO₂中空纤维材料上约为70%;该材料还具有良好的催化稳定性能,重复使用5次仍可使MB溶液的脱色降解率保持在90%以上,且该催化剂材料易于离心分离去除。     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

Preparation, characterization and photocatalytic performance of Mo-doped ZnO photocatalysts

A series of Mo-doped ZnO photocatalysts with different Mo-dopant concentrations have been prepared by a grinding-calcination method.The structure of these photocatalysts was characterized by a variety of methods,including N 2 physical adsorption,X-ray diffraction(XRD),scanning electron microscopy(SEM),Fourier transform infrared(FT-IR) spectroscopy,photoluminescence(PL) emission spectroscopy,and UV-vis diffuse reflectance spectroscopy(DRS).It was found that Mo 6+ could enter into the crystal lattice of ZnO due to the radius of Mo 6+(0.065 nm) being smaller than that of Zn 2+(0.083 nm).XRD results indicated that Mo 6+ suppressed the growth of ZnO crystals.The FT-IR spectroscopy results showed that the ZnO with 2 wt.% Mo-doping has a higher level of surface hydroxyl groups than pure ZnO.PL spectroscopy indicated that ZnO with 2 wt.% Mo-doping also exhibited the largest reduction in the intensity of the emission peak at 390 nm caused by the recombination of photogenerated hole-electron pairs.The activities of the Mo-doped ZnO photocatalysts were investigated in the photocatalytic degradation of acid orange II under UV light(λ = 365 nm) irradiation.It was found that ZnO with 2 wt.% Mo-doping showed much higher photocatalytic activity and stability than pure ZnO.The high photocatalytic performance of the Mo-doped ZnO can be attributed to a great improvement in the surface properties of ZnO,higher crystallinity and lower recombination rate of photogenerated hole-electron(e-/h+) pairs.Moreover,the undoped Mo species may exist in the form of MoO3 and form MoO3 /ZnO heterojunctions which further favors the separation of e-/h+ pairs.     

Calcination temperature-dependent morphology of photocatalytic ZnO nanoparticles prepared by an electrochemical–thermal method

ZnO nanoparticles (NPs) with tunable morphologies were synthesized by a hybrid electrochemical–thermal method at different calcination temperatures without the use of any surfactant or template. The NPs were characterized by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction, dynamic light scattering, thermogravimetry–differential thermal analysis, scanning electron microscope and N₂ gas adsorption–desorption studies. The FT-IR spectra of ZnO NPs showed a band at 450 cm^?1, a characteristic of ZnO, which remained fairly unchanged at calcination temperatures even above 300 °C, indicating complete conversion of the precursor to ZnO. The products were thermally stable above 300 °C. The ZnO NPs were present in a hexagonal wurtzite phase and the crystallinity of ZnO increased with an increasing calcination temperature. The ZnO NPs calcined at lower temperature were mesoporous in nature. The surface areas of ZnO NPs calcined at 300 and 400 °C were 51.10 and 40.60 m² g^?1, respectively, which are significantly larger than commercial ZnO nanopowder. Surface diffusion has been found to be the key mechanism of sintering during heating from 300 to 700 °C with the activation energy of sintering as 8.33 kJ mol^?1. The photocatalytic activity of ZnO NPs calcined at different temperatures evaluated by photocatalytic degradation of methylene blue under sunlight showed strong dependence on the surface area of ZnO NPs. The ZnO NPs with high surface area showed enhanced photocatalytic activity.     

The preparation and characterization of La doped TiO2 nanoparticles and their photocatalytic activity

In this paper, pure and La doped TiO₂ nanoparticles with different La content were prepared by a sol-gel process using Ti (OC₄H₉)₄ as raw material, and also were characterized by XRD, TG-DTA, TEM, XPS, DRS and Photoluminescence (PL) spectra. We mainly investigated the effects of calcining temperature and La content on the properties and the photocatalytic activity for degrading phenol of as-prepared TiO₂ samples, and also discussed the relationships between PL spectra and photocatalytic activity as well as the mechanisms of La doping on TiO₂ phase transformation. The results showed that La³⁺ did not enter into the crystal lattices of TiO₂ and was uniformly dispersed onto TiO₂ as the form of La₂O₃ particles with small size, which possibly made La dopant have a great inhibition on TiO₂ phase transformation; La dopant did not give rise to a new PL signal, but it could improve the intensity of PL spectra with a appropriate La content, which was possibly attributed to the increase in the content of surface oxygen vacancies and defects after doping La; La doped TiO₂ nanoparticles calcined at 600°C exhibited higher photocatalytic activity, indicating that 600°C was an appropriate calcination temperature. The order of photocatalytic activity of La doped TiO₂ samples with different La content was as following: 1>1.5>3>0.5>5>0 mol%, which was the same as the order of their PL intensity, namely, the stronger the PL intensity, the higher the photocatalytic activity, demonstrating that there were certain relationships between PL spectra and photocatalytic activity. This could be explained by the points that PL spectra mainly resulted from surface oxygen vacancies and defects during the process of PL, while surface oxygen vacancies and defects could be favorable in capturing the photoinduced electrons during the process of photocatalytic reactions.     

Synthesis, characterization and photoluminescence properties of Ce3+-doped ZnO-nanophosphors

The present study involves the synthesis of Ce³⁺ doped ZnO nanophosphors by the zinc nitrate and cerium nitrate co-precipitation method. The synthesized nanophosphors were characterized with respect to their crystal structure, crystal morphology, particle size and photoluminescence (PL) properties using X-ray diffraction (XRD), scanning electron microscopy (SEM)/energy dispersive X-ray (EDX), transmission electron microscopy (TEM)/Energy-dispersive X-ray spectroscopy (EDS) and PL-spectroscopy respectively. XRD results revealed that ZnO nanophosphors are single phase and cubic type structures. Further, PL spectra of ZnO:Ce³⁺ nanophosphors showed green emission because of the charge transfer at single occupied oxygen vacancies with ZnO holes and red emission due to the cerium ion transitions. Intensity and fine structure of the Ce³⁺ luminescence and its temperature dependence are strongly influenced by the doping conditions. The formation of ZnO:Ce³⁺ nanophosphors was confirmed by Fourier transform infrared (FTIR) and XRD spectra.     

Sol–gel synthesized vanadium doped TiO2 photocatalyst: physicochemical properties and visible light photocatalytic studies

Vanadium doped titanium dioxide (V–TiO₂) photocatalyst was synthesized by the sol–gel method using ammonium vanadate as vanadium source. The prepared samples were characterized by XRD, N₂ adsorption–desorption method, UV–Vis DRS, Fourier transform infrared (FTIR), scanning electron microscope–energy dispersive X-ray and photoluminescence (PL) analysis. The results show that V⁵⁺ ions were successfully incorporated into the crystal lattice of TiO₂ as a consequence, not only an obvious decrease in the band gap and a red shift of the absorption threshold into the visible light region was recorded for the V modified TiO₂, but, also a decrease in photogenerated electrons and holes recombination rate was observed as demonstrated by PL analysis. FTIR study indicated that in undoped TiO₂ sample the acetate group favored a bidentate bridging mode of binding with titanium atoms, whereas a bidentate chelating mode of linkage was observed in V–TiO₂ powders. The crystallite size of the samples calcined at 300 and 500 °C were decreased beyond the molar ratio of 200:1 (V:Ti), this may be due to dopant presence in the grain boundaries hindering the crystal growth. The photocatalytic activities for both pure and vanadium doped TiO₂ powders were tested in the discoloration of a reactive dyestuff, methylene blue, under visible light. The 100:1 (V:Ti) doped photocatalyst, calcined at 300 °C showed enhanced photocatalytic activity under visible light with a rate constant (k_obs) of 5.024 × 10^?3 min^?1 which is nearly five times higher than that of pure TiO₂, as result of low band gap value, high specific surface area and a decrease in recombination rate.     

掺杂Ce的TiO_2纳米粒子的光致光及其光催化活性

采用sol-gel法制备了纯的和掺杂不同量Ce的TiO_2纳米粒子，并利用XRD， TEM，BET，XPS和PL光谱对样品进行表征，主要考察焙烧温度和含量对掺杂Ce的 TiO_2纳米粒子性质以及光催化降解苯酚活性的影响，并探讨了Ce的掺杂对TiO_2相 变的作用机制以及PL光谱与光催化活性的关系，结果表明，掺杂的Ce~(4+)没有进 入到TiO_2晶格中，而是以小团簇的CeO_2化学态均匀地弥散在TiO_2纳米粒子中， 这可能导致了Ce的掺杂对TiO_2的相变有很大的抑制作用；Ce的掺杂没有引起新的 光致发光现象，而适量Ce的掺杂能够降低TiO_2纳米粒子PL光谱的强度，这是因为 掺杂的Ce~(4+)易于捕获光生电子而生成Ce~(3+);600℃处理的掺杂Ce的TiO_2纳米 粒子表现出较高的光催化活性，这说明600℃是比较合适的焙烧温度，而掺杂不同 量的Ce的TiO_2样品的光催化活性顺序是：3 mol%＞4 mol%＞2 mol%＞5 mol%＞1 mol%＞0 mol%，这与它们的PL光谱强度的顺序是相反的，即PL光谱强度越低，其 光催化活性越高，这说明PL光谱与其光催化活性间有着必然的联系，这是因为掺杂 剂Ce~(4+)能够捕获光生电子，在光致发光过程中使PL光谱强度下降，而在光催化 反应过程中使有机污染物加快氧化。     

形貌可控ZnO微纳米结构的水热合成及光催化性能

以乙醇胺为辅助溶剂,采用水热合成法,制备了花状、梭状和剑状的ZnO微纳米结构。采用扫描电镜(SEM)、X射线衍射(XRD)、光致发光光谱(PL)和拉曼光谱等测试手段对样品的形貌、结构、晶相等进行了表征。结果表明所有样品均为六方纤锌矿结构ZnO;其形貌和结晶度可通过改变物质的量的配比nZn2+/nOH-来调控。探讨了反应物配比对产物形貌结构的影响,乙醇胺对不同形貌ZnO的制备起到至关重要作用。以亚甲基蓝为目标降解物,采用紫外-可见吸收光谱(UV-Vis)并结合低温氮吸附-脱附比表面测试(BET),研究了花状、梭状和剑状ZnO的光催化活性。结果表明,与商用ZnO相比,制备的ZnO具有更好的光催化活性;样品催化活性与其比表面积不成正比,具有最小比表面积的花状ZnO拥有最好的光催化活性,这可能是由于其低的结晶度和特殊的花状形貌所致。     

形貌可控ZnO微纳米结构的水热合成及光催化性能

以乙醇胺为辅助溶剂,采用水热合成法,制备了花状、梭状和剑状的ZnO微纳米结构。采用扫描电镜（SEM）、Ｘ射线衍射（XRD）、光致发光光谱（PL）和拉曼光谱等测试手段对样品的形貌、结构、晶相等进行了表征。结果表明所有样品均为六方纤锌矿结构ZnO;其形貌和结晶度可通过改变物质的量的配比n_Zn²⁺/n_OH^-来调控。探讨了反应物配比对产物形貌结构的影响,乙醇胺对不同形貌ZnO的制备起到至关重要作用。以亚甲基蓝为目标降解物,采用紫外-可见吸收光谱（UV-Vis）并结合低温氮吸附-脱附比表面测试（BET）,研究了花状、梭状和剑状ZnO的光催化活性。结果表明,与商用ZnO相比,制备的ZnO具有更好的光催化活性;样品催化活性与其比表面积不成正比,具有最小比表面积的花状ZnO拥有最好的光催化活性,这可能是由于其低的结晶度和特殊的花状形貌所致。     

The effects of cerium doping concentration on the properties and photocatalytic activity of bimetallic Mo/Ce catalyst

In this study, the characterization and photocatalytic activity of MoO₃ nanoparticles doped with various doping concentrations of cerium have been investigated. The Fourier transform infrared (FT-IR) spectra of the prepared catalysts confirmed that MoO₃ particles have been successfully doped by cerium. Field emission scanning electron microscopy (FESEM) was performed to visualize the surface morphology of the obtained catalysts. The XRD patterns suggested that the crystallinity of the sample with the lowest doping concentration of 15 mol % was higher in comparison with samples of higher doping concentrations. The volume-averaged crystal sizes of the obtained catalysts were calculated to be 25, 28, and 32 nm for 15, 35, and 60 mol % samples, respectively. The photocatalytic activity along with the reaction kinetics of Ce-doped MoO₃ nanoparticles have also been investigated through the dye degradation of methyl orange. The synthesized Ce-doped MoO₃ particles with the lowest dopant concentration of 15 mol % exhibited the highest photocatalytic activity for methyl orange dye degradation. It was observed that photo-degradation activity decreased with an increase in the doping concentration of cerium. The predicted rate constants for samples with 15, 35, and 60 mol % doping concentrations were found to be 0.0432, 0.035, and 0.029 min^–1, respectively.