光催化材料Cu/Fe2O3-TiO2的结构和性能

光催化材料Cu/Fe2O3-TiO2的结构和性能;复合半导体;Cu/Fe2O3-TiO2;光催化材料;光响应性能     

(MoO3,ZnO)-TiO2/SiO2上光催化甲烷和水的反应性能

(MoO3;ZnO)-TiO2/SiO2上光催化甲烷和水的反应性能;TiO2/SiO2;MoO3;ZnO;甲烷;甲醇;光催化     

TiO2/SiO2气凝胶对吡啶的光催化降解

TiO2/SiO2气凝胶对吡啶的光催化降解;吡啶     

焙烧温度对TS/TiO2结构及光催化反应性能的影响

TS/TiO2是一种热稳定的光催化材料.将该样品分别在300、400、500、540、600和700℃下空气中焙烧,并用UV-Raman、XRD、BET及TPD等手段进行了表征.同时,以苯乙烯光催化氧化反应为探针,考察了其光催化氧化反应性能.结果表明,焙烧温度对催化剂的结构与表面性质有较大程度的影响,除TS/TiO2的晶型及比表面积外,其酸量也发生了较大程度的变化;并与催化剂性能进行了关联.     

MoS_2负载量对MoS_2/TiO_2光催化降解苯酚效率的影响及其作用机理研究

通过水解法制备TiO_2纳米颗粒,与经过超声处理后的MoS_2片层纳米材料复合制备MoS_2/TiO_2纳米催化剂,考察不同MoS_2负载量对其光催化降解苯酚效率及路径的影响。XRD、SEM、EDS、FT-IR和UV-vis DRS等表征结果表明,复合催化剂主要由锐钛矿型TiO_2和MoS_2组成;剥离后的MoS_2呈现薄片层状结构,均匀地分散在TiO_2纳米颗粒当中。光催化降解苯酚性能测试结果显示,对于MoS_2/TiO_2催化剂,MoS_2负载量的提高有利于光催化降解苯酚效率的提高;当MoS_2负载量为27%时,复合M o S2/TiO_2纳米颗粒的光催化性能最佳,反应80 min后可将苯酚完全降解。通过对苯酚降解过程中生成中间产物跟踪发现,MoS_2负载量的提高有利于促进中间产物苯醌、对苯二酚以及邻苯二酚的生成,进而提升了MoS_2/TiO_2复合材料的光催化性能。     

TiO_2/SnO_2复合光催化剂的耦合效应

采用改进的 sol-gel技术制备 TiO_2/SnO_2耦合型半导体光催化剂 ,利用 XRD、气相色谱仪、粒度仪和表面光电压装置等研究了耦合型半导体光催化机理和光催化效率的影响因素 ,并通过降解甲醛探讨其在空气污染治理中的作用 .实验结果表明 ,添加 20％ (mol) SnO_2的复合半导体光催化剂 ,其光催化效率比纯 TiO_2高一倍以上 .据实验结果和粒子紧密堆积原理 ,提出强耦合效应和弱耦合效应的光催化反应模型 ,并用此模型较好地解释了 TiO_2/SnO_2复合型半导体光催化剂的光催化效率随 SnO_2含量变化规律 .     

TiO2/SnO2复合光催化剂的制备及光催化降解敌敌畏

包覆型催化剂;TiO2/SnO2复合光催化剂的制备及光催化降解敌敌畏     

ZnFe2O4/Ag/TiO2复合材料的制备及其光催化性能

以硝酸银、钛酸四丁酯、无水氯化锌、六水氯化铁为原料,采用溶胶-凝胶法与溶剂热相结合的方法制备了ZnFe₂O₄/Ag/TiO₂复合材料,通过扫描电子显微镜、能谱分析仪、X射线粉末衍射仪、X射线光电子能谱仪、振动样品磁强计、紫外可见分光光度计对样品进行表征及测试。结果表明：ZnFe₂O₄/Ag/TiO₂-10具有最佳的光催化效果,在紫外和可见光下对染料的降解率都能达到90%以上,具有优异的紫外可见光光催化活性。ZnFe₂O₄/Ag/TiO₂具有独特的磁性,能在外部磁场作用下进行回收利用,这使其在实际应用中成为可能。通过磁分离技术重复回收利用5次后仍然保持优良的光催化性能,说明ZnFe₂O₄/Ag/TiO₂-10具有优异的磁性及较高的光催化循环稳定性。     

酞菁钴/SnO2纳米复合材料的原位合成及可见光光催化

酞菁钴/SnO2纳米复合材料的原位合成及可见光光催化;SnO2;酞菁钴;纳米复合材料;原位合成;光催化     

SO2-4/TiO2光催化氧化邻硝基苯酚

采用不同浓度的硫酸溶液浸渍处理TiO2,制得不同SO2-4含量的SO2-4/TiO2光催化剂.考察了光催化剂对邻硝基苯酚溶液的光催化行为.发现SO2-4/TiO2的光催化活性高于TiO2的光催化活性,浸渍液中H2SO4的浓度和焙烧温度对SO2-4/TiO2的催化活性有一定的影响,最佳浸渍H2SO4浓度为0.5 mol·L-1,最佳焙烧温度为500℃.     

The preparation of NbH5(Me2PCH2CH2Me2)2 and NbHL2(Me2PCH2CH2PMe2)2 (L = CO or C2H4)

MMe₅(dmpe) (M = Nb or Ta, dmpe = Me₂PCH₂CH₂PMe₂) reacts with H₂ (500 atm) and dmpe in THF at 60°C to give MH₅(dmpe)_2? NbH₅(dmpe)₂ readily reacts with two mol of CO or ethylene (L) to give NbHL₂(dmpe)₂. The exchange of the hydride ligand with the ethylene protons in NbH(C₂H₄)₂(dmpe)₂ is not rapid on the ¹H NMR time scale (60 MHz) at 95°C.     

Formation of nano-crystalline quartz crystals from ZnO/MgO/Al2O3/TiO2/ZrO2/SiO2 glasses

Glasses with the compositions 50.9 SiO₂ · 20.8 Al₂O₃ · (20.8 ? x) MgO· × ZnO · 3.7 TiO₂ · 3.7 ZrO₂ with x = 0, 2.3, 4.6 and 9.3 were annealed at temperatures in the range from 850 to 1100 °C. Depending on temperature, high- or low-quartz solid solutions, magnesium aluminosilicate, mullit and spinel precipitated. These glass–ceramics exhibit excellent mechanical properties and are potential candidates for applications in micromechanics or as hard disc substrate.The larger the ZnO concentration, the lower is the glass transition temperature. Also microhardnesses and Young’s moduli increased with increasing ZnO concentration. The nucleation temperature was of minor importance. To achieve good mechanical properties, the initially formed high-quartz phase must transform to the corresponding low-quartz phase. This occurs if the quartz phase contains only minor MgO or ZnO concentrations, which can be achieved by increasing the annealing times or temperature. Then MgO, ZnO and Al₂O₃ occur as separate spinel or gahnite phase.     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Removal of NO in NO/N2, NO/N2/O2, NO/CH4/N2, and NO/CH4/O2/N2 systems by flowing microwave discharges

In this paper, continuing previous work, we report on experiments carried out to investigate the removal of NO from simulated flue gas in nonthermal plasmas. The plasma-induced decomposition of small concentrations of NO in N2 used as the carrier gas and O2 and CH4 as minority components has been studied in a surface wave discharge induced with a surfatron launcher. The reaction products and efficiency have been monitored by mass spectrometry as a function of the composition of the mixture. NO is effectively decomposed into N2 and O2 even in the presence of O2, provided always that enough CH4 is also present in the mixture. Other majority products of the plasma reactions under these conditions are NH3, CO, and H2. In the absence of O2, decomposition of NO also occurs, although in that case HCN accompanies the other reaction products as a majority component. The plasma for the different reaction mixtures has been characterized by optical emission spectroscopy. Intermediate excited species of NO*, C*, CN*, NH*, and CH* have been monitored depending on the gas mixture. The type of species detected and their evolution with the gas composition are in agreement with the reaction products detected in each case. The observations by mass spectrometry and optical emission spectroscopy are in agreement with the kinetic reaction models available in literature for simple plasma reactions in simple reaction mixtures.     

Neue Verbindungen im System CaO/SiO2/CaCl2/H2O

New Compounds in the System CaO/SiO₂/CaCl₂/H₂O The hydrothermal formation of novel calcium silicate hydrates of compositions 5 CaO · 2 SiO₂ · CaCl₂ · 4 H₂O, 5 CaO · 2 SiO₂ · CaCl₂ · 2 H₂O and 4 CaO · 2 SiO₂ · CaCl₂ · H₂O from Ca₃SiO₅ and mixtures of CaO and SiO₂, respectively, in presence of calciumchloride at 200°–350 °C is described. From molybdate-reaction, ²⁹Si MAS NMR, DTA and TG measurements it is concluded that these compounds are based on disilicate anions and are to be interpreted as calcium hydroxide disilicate chlorides.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Solubility in the Na2Cr2O7-(NH4)2Cr2O7-K2Cr2O7-H2O system

Solubility in the Na₂Cr₂O₇-(NH₄)₂Cr₂O₇-K₂Cr₂O₇-H₂O four-component water-salt system at 25, 50, and 75°C was studied for the first time. Phase field boundaries for individual salts and potassium and ammonium dichromate solid solutions, monovariant lines, and invariant points were determined. Experimental data were used to optimize the looped isohydric process of potassium dichromate preparation involving additional salts.     

Formation of [Cp2TiSbMe2]2, [Cp2TiSb(SiMe3)2]2 and [Cp2TiCl]2·2Mes4Sb2

Reactions of [Cp₂Ti(btmsa)] (btmsa = bis(trimethylsilyl)acetylene) with R₄Sb₂ (R = Me, Me₃Si) give [Cp₂TiSbMe₂]₂ (1) or [Cp₂TiSb(SiMe₃)₂]₂ (2) respectively. [Cp₂TiCl]₂·2Mes₄Sb₂ (3) is serendipitously formed from [Cp₂Ti(btmsa)] and Mes₂SbH containing NH₄Cl traces.     

Conversion of NO in NO/N2, NO/O2/N2, NO/C2H4/N2 and NO/C2H4/O2/N2 Systems by Dielectric Barrier Discharge Plasmas

An experimental study on the conversion of NO in the NO/N₂, NO/O₂/N₂, NO/C₂H₄/N₂ and NO/C₂H₄/O₂/N₂ systems has been carried out using dielectric barrier discharge (DBD) plasmas at atmospheric pressure. In the NO/N₂ system, NO decomposition to N₂ and O₂ is the dominating reaction; NO conversion to NO₂ is less significant. O₂ produced from NO decomposition was detected by an on-line mass spectrometer. With the increase of NO initial concentration, the concentration of O₂ produced decreases at 298 K, but slightly increases at 523 K. In the NO/O₂/N₂ system, NO is mainly oxidized to NO₂, but NO conversion becomes very low at 523 K and over 1.6% of O₂. In the NO/C₂H₄/N₂ system, NO is reduced to N₂ with about the same NO conversion as that in the NO/N₂ system but without NO₂ formation. In the NO/C₂H₄/O₂/N₂ system, the oxidation of NO to NO₂ is dramatically promoted. At 523 K, with the increase of the energy density, NO conversion increases rapidly first, and then almost stabilizes at 93–91% of NO conversion with 61–55% of NO₂ selectivity in the energy density range of 317–550 J L⁻¹. It finally decreases gradually at high energy density. A negligible amount of N₂O is formed in the above four systems. Of the four systems studied, NO conversion and NO₂ selectivity of the NO/C₂H₄/O₂/N₂ system are the highest, and NO/O₂/C₂H₄/N₂ system has the lowest electrical energy consumption per NO molecule converted.     

Slow energy transfer between vibrational models of CH2Cl2, CD2Cl2, CH2ClBr and CH2Br2

Inefficient vibrational energy exchange between the lowest vibrational mode and the higher lying vibrational modes of CH₂Cl₂, CD₂Cl₂, CH₂ClBr and CH₂Br₂ was investigated by ultrasonic absorption experiments. Breathing sphere theory is used to interpret the data available for VV and VR, T transfer in methylene halides.