Computer controlled-flow injection potentiometric system based on virtual instrumentation for the monitoring of metal-biosorption processes

A completely automated flow-injection system was developed for the monitoring of biosorption studies of Cu(II) ion on vegetable waste by-products. The system employed flow-through Cu(II)-selective electrodes, of epoxy-resin-CuS/Ag₂S heterogeneous crystalline type, and computer controlled pumps and valves for the flow operation. Computer automation was done through a specially devised virtual instrument, which commanded and periodically calibrated the system, allowing for the monitoring of Cu(II) ions between 0.6 and 6530 mg L⁻¹ at a typical frequency of 15 h⁻¹. Grape stalk wastes were used as biosorbent to remove Cu(II) ions in a fixed-bed column with a sorption capacity of 5.46 mg g⁻¹, obtained by the developed flow system, while the reference determination performed by FAAS technique supplied a comparable value of 5.41 mg g⁻¹.     

2-{[1-(3,4-Dihydroxyphenyl)methylidene]amino}benzoic acid immobilized Amberlite XAD-16 as metal extractant

2-{[1-(3,4-Dihydroxyphenyl)methylidene]amino}benzoic acid (DMABA) was loaded on Amberlite XAD-16 (AXAD-16) via azo linker and the resulting resin AXAD-16-DMABA explored for enrichment of Zn(II), Mn(II), Ni(II), Pb(II), Cd(II), Cu(II), Fe(III) and Co(II). The optimum pH values for extraction are 6.5-7.0, 5.0-6.0, 5.5-7.5, 5.0-6.5, 6.5-8.0, 5.5-7.0, 4.0-5.0 and 6.0-7.0, respectively. The sorption capacity was found between 97 and 515 μmol g⁻¹ and the preconcentration factors from 100 to 450. Tolerance limits for foreign species are reported. The kinetics of sorption is fast as t_1/2 is ≤5 min. The chelating resin can be reused for 50 cycles of sorption-desorption without any significant change (<1.5%) in the sorption capacity. The limit of detection values (blank +3 s) are 1.12, 1.38, 1.76, 0.67, 0.77, 2.52, 5.92 and 1.08 μg L⁻¹ for Zn(II), Mn(II), Ni(II), Pb(II), Cd(II), Cu(II), Fe(III) and Co(II), respectively. The enrichment on AXAD-16-DMABA coupled with monitoring by flame atomic absorption spectrometry (FAAS) is used to determine all the metal ion ions in river and synthetic water samples, Co in vitamin tablets and Zn in milk samples.     

Structural and vibrational characterization of [KrF][AuF6] and α-[O2][AuF6] using single crystal X-ray diffraction, Raman spectroscopy and electron structure calculations

The salt [KrF][AuF₆] has been prepared by the direct oxidation of gold powder in anhydrous HF at 20 °C using the potent oxidative fluorinating agent KrF₂. The KrF⁺ salt readily oxidizes molecular oxygen at ambient temperature to yield [O₂][AuF₆]. Variable temperature Raman spectroscopy has been used to identify a reversible phase transition in [O₂][AuF₆], which occurs between −114 and −118 °C. Single crystal X-ray diffraction has been used to characterize the low-temperature, α-phase of [O₂][AuF₆]. The phase transition is attributed to ordering of the O₂⁺ cation in the crystal lattice, which is accompanied by minor distortions of the AuF₆⁻ anion. The α-phase of [O₂][AuF₆] crystallizes in the triclinic space group , with a=4.935(6) Å, b=4.980(6) Å, c=5.013(6) Å, α=101.18(1)°, β=90.75(2)°, γ=101.98(2)°, V=342.97 Å³, Z=1, and R₁=0.0481 at −122 °C. The structure of the precursor, [KrF][AuF₆], has also been determined by single crystal X-ray diffraction and crystallizes in the monoclinic space group Cc with a=7.992(3) Å, b=7.084(3) Å, c=10.721(4) Å, β=105.58(1)°, V=584.8(4) Å³, Z=4 and R₁=0.0389 at −125 °C. The KrF⁺ and AuF₆⁻ ions interact by means of a FKr---FAu fluorine bridge that is bent by 125.3(7)° about the bridge fluorine. The KrF_t and Kr---F_b bond lengths in [KrF][AuF₆] were determined to be 1.76(1) and 2.15(1) Å, respectively. The energy minimized structures of the [KrF][AuF₆] ion-pair and the AuF₆⁻ anion have been determined at the Hartree-Fock (HF), MP2 and local density functional (LDF) levels of theory. These calculations have also been used to assign the vibrational spectrum of the [KrF][AuF₆] ion-pair in greater detail and to reassign the vibrational spectrum of the AuF₆⁻ anion.     

Copper(II) complexes of symmetrical and unsymmetrical tetradentate Schiff base ligands incorporating 1-benzoylacetone: Synthesis,crystal structures and electrochemical behavior

Three new copper(II) complexes [CuL¹]₂(ClO₄)₂ (1), [CuL²]ClO₄ (2) and [CuL³] (3) with three Schiff base ligands [HL¹ = 1-phenyl-3-{3-[(pyridin-2-ylmethylene)-amino]-propylimino}-butan-1-one, HL² = 1-phenyl-3-[3-(1-pyridin-2-yl-ethylideneamino)-propylimino]-butan-1-one and H₂L³ = 3-[3-(1-methyl-3-oxo-3-phenyl-propylideneamino)-propylimino]-1-phenyl-butan-1-one] have been synthesized and structurally characterized by X-ray crystallography. The mono-negative tetradentate asymmetric Schiff base ligands (L¹)⁻ and (L²)⁻ are chelated in complexes 1 and 2 to form square planar copper(II) complexes. In complex 1, the two units are associated weakly through ketonic oxygen of benzoylacetone fragment to form the dimeric entity. The square planar geometry of complex 3 is unusually distorted towards tetrahedral one. All three complexes exhibit reversible cyclic voltammetric responses in acetonitrile solution corresponding to the Cu^II/Cu^I redox process. The E_1/2 (−0.47 V versus SCE) of 3 shows significant anodic shift due to the tetrahedral distortion around Cu(II) compare to that of 1 and 2 (−0.82 and −0.87 V versus SCE, respectively).     

Vinyl addition polymerization of norbornene catalyzed by β-iminoamine Ni(II) complexes/methylaluminoxane systems

Two nickel(II) complexes (A and B) bearing β-iminoamine ligands, [2-(ArNCH)-C₆H₄-NMe₂] (La, Ar = 2,6-i-Pr₂C₆H₃; Lb, Ar = 2,6-Me₂C₆H₃), were synthesized and characterized by elemental analyses and ¹H NMR. X-ray crystal structure of complex B reveals that the six-membered chelate ring adopts a envelope conformation, with nickel(II) atom deviating from the plane of backbone aromatic ring by 1.164 Å. In the presence of methylaluminoxane (MAO), both complexes showed moderate activities of 10⁵ g mol_Ni⁻¹ h⁻¹ for norbornene polymerization. β-iminoamine Ni(II)/MAO catalysts gave unimodal polymers (M_w, 3.16-8.02 × 10⁵ g/mol) with a relatively narrow MWD (M_w/M_n, 1.59-2.14), indicative of single-site catalyst behavior. The obtained polymers are vinyl-type polynorbornenes (PNBs), which are soluble in common solvents such as toluene, cyclohexane and dichlorobenzene.     

Chemically modified silica gel with aminothioamidoanthraquinone for solid phase extraction and preconcentration of Pb(II), Cu(II), Ni(II), Co(II) and Cd(II)

Silica gel chemically bonded with aminothioamidoanthraquinone was synthesized and characterized. The metal sorption properties of modified silica were studied towards Pb(II), Cu(II), Ni(II), Co(II) and Cd(II). The determination of metal ions was carried out on FAAS. For batch method, the optimum pH ranges for Pb(II), Cu(II) and Cd(II) extraction were ≥3 but for Ni(II) and Co(II) extraction were ≥4. The contact times to reach the equilibrium were less than 10 min. The adsorption isotherm fitted the Langmuir's model showed the maximum sorption capacities of 0.56, 0.30, 0.15, 0.12 and 0.067 mmol/g for Pb(II), Cu(II), Ni(II), Co(II) and Cd(II), respectively. In the flow system, a column packed modified silica at 20 mg for Pb(II) and Cu(II), 50 mg for Cd(II), 60 mg for Co(II), Ni(II) was studied at a flow rate of 4 and 2.5 mL/min for Ni(II). The sorbed metals were quantitatively eluted by 1% HNO₃. No interference from Na⁺, K⁺, Mg²⁺, Ca²⁺, Cl⁻ and SO₄²⁻ at 10, 100 and 1000 mg/L was observed. The application of this modified silica gel to preconcentration of pond water, tap water and drinking water gave high accuracy and precision (%R.S.D. ≤ 9). The method detection limits were 22.5, 1.0, 2.9, 0.95, 1.1 μg/L for Pb(II), Cu(II), Ni(II), Co(II) and Cd(II), respectively.     

Novel nickel(II) and copper(II) complexes with phenoxy-imidazole ligands: Syntheses, crystal structures and norbornene addition polymerization

The novel nickel(II) (1) and copper(II) (2) complexes bearing 2′-(4′,6′-di-tert-butylhydroxy-phenyl)-1,4,5-triphenyl imidazole ligand have been synthesized and characterized. The molecular structure analyses of complexes 1 and 2 indicated that Ni(II) centre in 1 adopts a distorted tetrahedral coordination geometry with a dihedral angle of 85.2° between Ni(1)O(1)N(1) plane and Ni(1)O(1A)N(1A) plane, while the Cu(II) centre in 2 represents a distorted square planar coordination geometry with a cis-N₂O₂ arrangement of the donor atoms, the dihedral angle being 32° between Cu(1)O(1)N(1) plane and Cu(1)O(1A)N(1A) plane. After activation with methylaluminoxane (MAO), both Ni(II) and Cu(II) complexes can be used as catalysts for the addition polymerization of norbornene (NB). The polynorbornenes (PNBs) are produced with very high polymerization activity (10⁸ g PNB mol⁻¹ Ni h⁻¹) for Ni(II) complex and moderate catalytic activity (10⁵ g PNB mol⁻¹ Cu h⁻¹) for Cu(II) complex, respectively. The high molecular weight polynorbornenes (10⁶) are obtained for complexes 1 and 2. Moreover, the distinct effects of polymerization temperature and Al/M ratio on catalytic activities and molecular weights of polymers are discussed.     

Simultaneous determination of Mn(II), Cu(II) and Fe(III) as 2-(5′-bromo-2′-pyridylazo)-5-diethylaminophenol complexes by adsorptive cathodic stripping voltammetry at a carbon paste electrode

A simple and precise square-wave adsorptive cathodic stripping voltammetry (SW-AdCSV) method has been described for simultaneous determination of Mn(II), Cu(II) and Fe(III) in water samples using a carbon paste electrode. In 0.1 mol L⁻¹ acetate buffer (pH 5) containing 50 μmol L⁻¹ of 2-(5′-bromo-2′-pyridylazo)-5-diethylaminophenol (5-Br-PADAP), Mn(II), Cu(II) and Fe(III) were simultaneously determined as metal-complexes with 5-Br-PADAP following preconcentration onto the carbon paste electrode by adsorptive accumulation at +1.0 V (vs. Ag/AgCl/3 M KCl). Insignificant interference from various cations (K⁺, Na⁺, Mg²⁺, Ca²⁺, Al³⁺, Bi³⁺, Sb³⁺, Se⁴⁺, Zn²⁺, Ni²⁺, Co²⁺, Cd²⁺, Pb²⁺, V⁵⁺, Ti⁴⁺ and NH₄⁺), anions (HCO₃⁻, Cl⁻, NO³⁻, SO₄²⁻ and PO₄³⁻) and ascorbic acid was noticed. Limits of detection of 0.066, 0.108 and 0.093 μg L⁻¹ and limits of quantitation of 0.22, 0.36 and 0.31 μg L⁻¹ Mn(II), Cu(II) and Fe(III), respectively, were achieved by the described method. The described stripping voltammetry method was successfully applied for simultaneous determination of Mn(II), Cu(II) and Fe(III) in ground, tap and bottled natural water samples.     

4-{[(2-Hydroxyphenyl)imino]methyl}-1,2-benzenediol (HIMB) anchored Amberlite XAD-16: Preparation and applications as metal extractants

Amberlite XAD-16 was loaded with 4-{[(2-hydroxyphenyl)imino]methyl}-1,2-benzenediol (HIMB) via azo linker and the resulting resin AXAD-16-HIMB explored for enrichment of Zn(II), Mn(II), Ni(II), Pb(II), Cd(II), Cu(II), Fe(III) and Co(II) in the pH range 5.0-8.0. The sorption capacity was found between 56 and 415 μmol g⁻¹ and the preconcentration factors from 150 to 300. Tolerance limits for foreign species are reported. The kinetics of sorption is not slow, as t_1/2 is ≤15 min. The chelating resin can be reused for seventy cycles of sorption-desorption without any significant change (<2.0%) in the sorption capacity. The limit of detection values (blank + 3 s) are 1.72, 1.30, 2.56, 2.10, 0.44, 2.93, 2.45 and 3.23 μg l⁻¹ for Zn, Mn, Ni, Pb, Cd, Cu, Fe and Co, respectively. The enrichment on AXAD-16-HIMB coupled with flame atomic absorption spectrometry (FAAS) monitoring is used to determine the metal ion ions in river and synthetic water samples, Co in vitamin tablets and Zn in powdered milk samples.     

Rhenium(IV)–copper(II) heterobimetallic complexes: Synthesis,crystal structure and magnetic properties

Two Re(IV)–Cu(II) heterometallic complexes {(CuL_α)[ReCl₄(ox)]}_n (where L_α = N-meso-5,12-Me₂-7,14-Et₂-[14]-4,11-dieneN₄), 1, and (CuL_β)[ReCl₄(ox)] (L_β = N-rac-5,12-Me₂-7,14-Et₂-[14]-4,11-dieneN₄N-rac-5,12-Me₂-7,14-Et₂-[14]-4,11-dieneN₄), 2, were synthesized. The [CuL²⁺] macrocyclic cation is coordinated from above and below by [ReCl₄(ox)]²⁻ units through the chloro-ligands and creates a chloro-bridged heterometallic Re^IV–Cu^II one-dimensional zig-zag chain. Compound 2 can be viewed as a heterobimetallic dinuclear unit, in which the Re(IV)-Cu(II) centers are linked by an oxalato bridge. The magnetic behavior of 1 and 2 has been investigated over the temperature range 1.8–300 K. Compound 1 behaves like a ferrimagnetic {Re(IV)–Cu(II)} bimetallic, one-dimensional chain with intrachain antiferromagnetic coupling. Compound 2 shows a weak antiferromagnetic interaction within the [Re(IV)–Cu(II)] unit along with a strong single-ion anisotropy, D(Re) = −63 cm⁻¹.     

Highly selective preconcentration of Cu(II) from seawater and water samples using amidoamidoxime silica

Chemically modified silica containing amidoamidoxime group was studied as a sorbent for solid-phase extraction (SPE) and preconcentration of Cu(II) prior to determination by flame atomic absorption spectrometry (FAAS). The sorbent showed an extremely high selectivity towards Cu(II) in the pH range of 4-6, while the extraction of Pb(II), Cd(II), Ni(II) and Co(II) was low. The adsorption isotherm followed the Langmuir model and the maximum sorption capacity of 0.0163 mmol Cu(II) g⁻¹ was achieved. In the flow system, Cu(II) was completely retained on a column containing 40 mg of the modified silica at the flow rate of 4.0 mL min⁻¹ and quantitatively eluted by 5 mL of 1% (v/v) HNO₃. No interference from Na⁺, K⁺, Mg²⁺, Ca²⁺, Cl⁻ and SO₄²⁻ at 10, 100 and 1000 mg L⁻¹ was observed. When applied for preconcentration and determination of Cu(II) in tap water, pond water, and seawater, the recoveries were 96, 101, and 95%, respectively, with high precision (% relative standard deviation (R.S.D.) < 4) and low method detection limit (9 μg L⁻¹).     

Two new coordination polymers of Robson-type macrocycle bridged by perchlorate anions: Structure,electrochemistry and magnetism

Two new coordination polymers of Robson-type macrocycles, [Cu₂L¹(μ-ClO₄)₂]_∞ (1) and [Cu₂L²(μ-ClO₄)₂]_∞ (2) (where H₂L¹and H₂L² are the [2+2] condensation products of 2,6-diformyl-4-flurophenol with 1,3-diaminopropane and 2-hydroxy-1,3-diaminopropane, respectively), have been synthesized and characterized. The intriguing feature is that intermolecular perchlorato bridges occur between adjacent copper(II) centers. The cyclic voltammograms of the complexes show that each complex undergoes two pseudo-reversible processes with the half wave potentials, −0.361 V and −0.729 V for 1, and −0.372 V and −0.744 V for 2, respectively. Magnetic susceptibility was measured for 1 and 2 over a temperature range of 2–300 K. The optimized magnetic data were J = −359.6 cm⁻¹, j′ = −30 cm⁻¹ and R = 6.8 × 10⁻⁸ for 1 and J = −411 cm⁻¹, j′ = −26 cm⁻¹ and R = 2.4 × 10⁻⁷ for 2, respectively. The data reveal antiferromagnetic couplings between the copper(II) ions of intra- and intermolecular units.     

Synthesis and characterization of para-nitro substituted 2,6-bis(phenylimino)pyridyl Fe(II) and Co(II) complexes and their ethylene polymerization properties

Four iron(II) and cobalt(II) complexes ligated by 2,6-bis(4-nitro-2,6-R₂-phenylimino)pyridines, LMCl₂ (1: R = Me, M = Fe; 2: R = iPr, M = Fe; 3: R = Me, M = Co; 4: R = iPr, M = Co) have been synthesized and fully characterized, and their catalytic ethylene polymerization properties have been investigated. Among these complexes, the iron(II) pre-catalyst bearing the ortho-isopropyl groups (complex 2) exhibited higher activities and produced higher molecular weight polymers than the other complexes in the presence of methylaluminoxane (MAO). A comparison of 2 with the reference non-nitro-substituted catalyst (2,6-bis(2,6-diisopropylphenylimino)pyridyl)FeCl₂ (FeCat 5) revealed a modest increase of the catalytic activity and longer lifetime upon substitution of the para-positions with nitro groups (activity up to 6.0 × 10³ kg mol⁻¹ h⁻¹ bar⁻¹ for 2 and 4.8 × 10³ kg mol⁻¹ h⁻¹ bar⁻¹ for 5), converting ethylene to highly linear polyethylenes with a unimodal molecular weight distribution around 456.4 kg mol⁻¹. However, the iron(II) pre-catalyst 1 on changing from ortho-isopropyl to methyl groups displayed much lower activities (over an order of magnitude) than 2 under mild conditions. As expected, the cobalt analogues showed relatively low polymerization activities.     

Solid phase extraction of metal ions using carbon nanotubes

The sorption behaviour of carbon nanotubes (CNTs) toward some divalent metal ions such as Cu(II), Co(II), Ni(II), Zn(II), Pb(II), Mn(II) and Cd(II) has been investigated systematically. The affinity order of the metal ions towards CNTs at pH in the range of 7.0-9.0 was: Cu(II) > Pb(II) > Zn(II) > Co(II) > Ni(II) > Cd(II) > Mn(II). The experimental parameters for preconcentration of copper, which exhibits the highest affinity towards carbon nanotubes, on a microcolumn packed with CNTs prior to its determination by flame atomic absorption spectrometry have been investigated. Copper can be quantitatively retained at pH 8.2 from sample volume up to 150 mL and then eluted completely with 0.1 mol L^− 1 HNO₃. The limit of detection limit for Cu(II) determination with FAAS detection was 2.1 μg L^− 1, and the RSD was 3.5% at the 50 μg L^− 1 level. Under the optimal conditions for copper enrichment also Zn(II), Pb(II) and Ni(II) could be quantitatively preconcentrated from water samples. The method was validated using a certified reference materials BCR-610 and SRM 1640.     

pH-dependent self-assembly of copper(II) complexes with a new imidazole-containing polyamine ligand: Synthesis,structure and magnetic property

Four copper(II) complexes were synthesized by reactions of new imidazole-containing polyamine ligand N¹-(2-aminoethyl)-N¹-(1H-imidazol-4-ylmethyl)-ethane-1,2-diamine (HL) with Cu(ClO₄)₂ · 6H₂O under different pH and their structures were characterized by X-ray crystallography. Interestingly, the complexes have diverse structures from protonated ligand [H₃(HL)][CuCl₄] · Cl (1), dinuclear [Cu₂(HL)₂Cl](ClO₄)₃ · H₂O (2), one-dimensional chain polynuclear {[Cu(L)](ClO₄)}_n (3) to cyclic-tetranuclear [Cu₄(L)₄](ClO₄)₄ · 3CH₃CN (4) coordination compounds by varying reaction pH from acidic to basic. The results indicate that the reaction pH has great impact on the formation and structure of the complexes. The magnetic measurements show that there are antiferromagnetic interactions between the Cu(II) centers with g = 2.09, J = −39.0 cm⁻¹ and g = 2.17, J = −36.8 cm⁻¹ for 3 and 4, respectively.     

Synthesis, characterization and luminescence properties of copper(I) complexes containing 2-phenyl-3-(benzylamino)-1,2-dihydroquinazolin-4(3H)-one and triphenylphosphine as ligands

Some copper(I) complexes of the formula [Cu(L)(PPh₃)₂]X (1-4) [where L = 2-phenyl-3-(benzylamino)-1,2-dihydroquinazolin-4(3H)-one; PPh₃ = triphenylphosphine; X = Cl⁻, NO₃⁻, ClO₄⁻ and BF₄⁻] have been prepared and characterized on the basis of elemental analysis, IR, UV-Vis and ¹H NMR spectral studies. The representative complex of the series 4 has been characterized by single crystal X-ray diffraction which reveal that in the complex the central copper(I) ion assumes the irregular distorted-tetrahedral geometry. Cyclic voltammetry of the complexes indicate a quasireversible redox behavior corresponding to Cu(II)/Cu(I) couple. All the complexes exhibit intraligand (π → π^∗) fluorescence with high quantum yield in dichloromethane solution.     

Oxidative and hydrolytic DNA cleavage by Cu(II) complexes of salicylidene tyrosine schiff base and 1,10 phenanthroline/bipyridine

Ternary Cu(II) complexes [Cu(II)(saltyr)(B)] (1,2), (saltyr = salicylidene tyrosine, B = 1,10 phenanthroline (1) or 2,2′ bipyridine (2)) were synthesized and characterized by various techniques. The complexes exhibit square pyramidal (CuN₃O₂) geometry. CT-DNA binding studies revealed that the complexes show good binding propensity (K_b = 3.47 × 10⁴ M⁻¹ and 3.01 × 10⁴ M⁻¹ for 1 and 2, respectively). The role of these complexes in the oxidative and hydrolytic DNA cleavage was studied. The catalytic ability of 1 and 2 follows the order: 1 > 2. The rate constants for the hydrolysis of phosphodiester bond were determined as 2.80 h⁻¹ and 2.11 h⁻¹ for 1 and 2, respectively. It amounts to (0.58-0.77) × 10⁸ fold rate enhancement compared to non-catalyzed DNA cleavage, which is significant.     

Synthesis of light-emmting materials bis-[2′-2″-(9H-fluoren-2-yl)-vinyl-8-hydroxyquinoline] zinc(II) and bis-[2′-4″-(4,5-diphenyl-1H-imidazol-2-yl)styryl-8-hydroxyquinoline] zinc(II)

Two novel light-emitting materials bis-[2′-2″-(9H-fluoren-2-yl)-vinyl-8-hydroxyquinoline] zinc(II) (3) and bis-[2′-4″-(4,5-diphenyl-1H-imidazol-2-yl)styryl-8-hydroxyquinoline] zinc(II) (4) containting 8-hydroxyquinoline and fluorene or imidazole moieties have been synthesized. The optical properties of these complexes were influenced by the styryl substituents, and exhibited orange-emission. They have higher fluorescence quantum yields than Alq₃, and good stabilities with thermal decomposition temperatures 395 °C and 435 °C. The single-layer OLED fabricated by 3 emitted lemon-yellow, and exhibited good device performance with a maximum luminance of 489 cd m⁻², and luminance efficiency of up to 0.41 cd A⁻¹. The single-layer OLED fabricated by 4 emitted yellow-green, and exhibited good device performance with a maximum luminance of 323 cd m⁻², and luminance efficiency of up to 0.54 cd A⁻¹.     

Synthesis, structure, and ionic conductivity of Na5Li3Ti2S8

The compound Na₅Li₃Ti₂S₈ has been synthesized by the reaction of Ti with a Na/Li/S flux at 723 K. Na₅Li₃Ti₂S₈ crystallizes in a new structure type with four formula units in space group C2/c of the monoclinic system. The structure contains three crystallographically independent Na⁺ cations and two crystallographically independent Li⁺ cations. Na₅Li₃Ti₂S₈ possesses a channel structure that features two-dimensional layers built from Li(1)S₄ and TiS₄ tetrahedra. The layers, which are stacked along c, comprise eight-membered rings and sixteen-membered rings. Na(3)⁺ cations are located between the eight-membered rings and Na(1)⁺, Na(2)⁺, and Li(2)⁺ cations are located between the sixteen-membered rings. These cations are each octahedrally coordinated by six S²⁻ anions. The ionic conductivity σ_T of Na₅Li₃Ti₂S₈ ranges from 8.8×10⁻⁶ S/cm at 303 K to 3.8×10⁻⁴ S/cm at 483 K. The activation energy E_a is 0.40 eV.