Microwave-assisted extraction of metal elements from glass fibrous filters for aerosol sampling

Atmospheric aerosols are generally collected on filters according to the International Monitoring System (IMS) designed in the Comprehensive Nuclear-Test-Ban Treaty (CTBT). More information could be revealed when the filter sample is pretreated rather than measured directly by g-ray spectrometer. Microwave-assisted extraction (MAE) is a suitable method that gives higher recoveries of elements from glass fibrous filters under different conditions. The results indicate that the MAE is a highly efficient and robust method for the treatment of glass fibrous filter samples. The recoveries of potential fission products from glass fibrous filter samples by microwave-assisted extraction meet the efficiency of the extraction by both aqua regia and 2% HCl.     

Comparative study of pretreatment methods for the determination of metals in atmospheric aerosol by electrothermal atomic absorption spectrometry

A comparative study of pretreatment methods for the determination of 10 elements (As, Cd, Pb, V, Ni, Mn, Cr, Cu, Fe, Al) in atmospheric aerosols by electrothermal atomic absorption spectrometry (ETAAS) was conducted. For the digestion of the particulates collected in filters, six methods were compared using a mixture of HNO₃ and HF with or without the addition of various oxidative agents (HClO₄ or H₂O₂) or acids (HCl). The comparative study was performed using loaded cellulose filter samples, which were digested in Parr bombs and heated in a conventional oven at 170 °C for 5 h. The extraction efficiency and blanks were compared and it was proved that the digestion method using only HNO₃–HF extracted most of the metals and gave the lowest blanks. The HNO₃–HF mixture was selected for the development of an improved microwave digestion method specific for aerosol-loaded filters. The operating parameters were optimized, so that quantitative recovery of the reference materials NIST 1649a urban dust and NIST 1648 urban particulate matter was achieved. The blank of cellulose and teflon filters were also determined and compared. Teflon filters present the lowest blanks for all the elements. The obtained limits of detection for each type of filters were adequate for environmental monitoring purposes. ETAAS instrumental operation was also optimized for the compensation and the elimination of interferences. The temperature optimization was performed for each metal in every type of filter and optimized parameters are proposed for 10 elements.     

微波消解-分光光度法测定石油焦中的硅

重点研究了微波消解石油焦样品的方法,详细考察了微波消解时样品的最佳用量、消解压力、消解功率、消解时间,建立了最佳微波消解程序：在样品处理中也采用了常规溶样方法,并分别用两种样品处理方法测定石油焦中的硅。结果表明两种方法测定结果基本吻合,样品测定的RSD小于3．85％,加标回收率在97％～103％之间,但微波消解法的溶样速度是常规法的10倍。实验结果表明,微波消解分光光度法测定石油焦中的硅是一种快速、准确且无环境污染的绿色环保方法,具有一定的实用价值。     

Determination of heavy metals in soil, mushroom and plant samples by atomic absorption spectrometry

The concentrations of heavy metals in the soil, mushroom and plant samples collected from Tokat, Turkey have been determined by flame and graphite furnace atomic absorption spectrometry after dry ashing, wet ashing and microwave digestion. The study of sample preparation procedures showed that the microwave digestion method was the best. Good accuracy was assured by the analysis of standard reference materials. The relative standard deviations for all measured metal concentrations were lower than 10%. In all cases, quantitative analytical recoveries ranging from 95 to 103% were obtained. Metal accumulation factors were calculated for mushroom and plant samples. High ratio of plants to soil cadmium, zinc and copper concentrations indicate that these elements are accumulated by mushrooms. Results obtained are in agreement with data reported in the literature.     

虾粉中总砷测定方法的探讨

用氢化物原子荧光光度法测定虾粉中总砷含量时,对干法灰化、湿法消解、微波消解3种样品处理方法对虾粉中砷元素测定结果的影响进行了比较。通过试验确定了最佳消解条件。砷元素浓度在0~10μg/L的范围内与荧光强度呈线性关系,线性相关系数r=0.999 6,检出限为0.2μg/L。比对结果表明,干法灰化适合于测定虾粉中总砷的含量,湿法消解测定总砷的含量偏低,微波消解不适合测定虾粉中总砷的含量。采用干法灰化-氢化物原子荧光光度法测定虾粉中总砷含量,加标回收率为76.2%~106.0%。     

Determination of thirteen common elements in food samples by inductively coupled plasma atomic emission spectrometry: comparison of five digestion methods

Five sample digestion procedures were evaluated for the determination of Al, B, Ca, Cu, Fe, K, Mg, Mn, Na, P, S, Sr, and Zn in food samples by inductively coupled plasma atomic emission spectrometry. The 5 procedures include dry ashing at 500 degrees C, wet digestion with HNO3-HClO4, microwave digestion with HNO3, microwave digestion with HNO3-H2O2, and microwave digestion with HNO3-H2O2-HF. For microwave digestion with HNO3-H2O2-HF, silicon (IV) oxide was used to eliminate the excess HF, making it possible to determine total Al, B, and other common elements accurately and simultaneously. Seven National Institute of Standards and Technology standard reference materials (SRMs) were analyzed to compare the recovery of 13 elements with above digestion procedures. The results demonstrated that the microwave digestion procedure with HNO3-H2O2-HF yielded the best recoveries for all 13 elements in the selected SRMs. The determined concentrations of most elements were close for all 3 microwave digestion procedures with the exception of Al in oyster tissue, bovine liver, and spinach. Notably, the wet digestion with HNO3-HClO4 is the simplest and the most effective procedure for the selected elements except Al and B. Although there are several concerns with the dry ashing procedure, it might be a preferable procedure for those analyses where only nonvolatile elements are to be determined and the concentrations of the elements are low.     

A study of sample mineralization methods for arsenic analysis of blood and urine by hydride generation and graphite furnace atomic absorption spectrometry

Mineralization procedures for blood and urine suitable for the determination of arsenic by Hydride Generation Atomic Absorption Spectrometry (HGAAS) are studied on model samples, and the results are utilized in biological monitoring investigations. The objective of this work is to obtain good total As recoveries for both matrices regardless of added As species (As(III), As(V), DMA, MMA, AsB, or AsC). Prior to the HGAAS analyses, preparation procedures were controlled under optimised conditions by graphite furnace atomic absorption spectrometry (GFAAS). Two preparation procedures for urine give As recoveries close to 100% by HGAAS: a) dry ashing at 420°C with Mg(NO₃)₂ on a hot plate, and b) microwave oven decomposition with (NH₄)₂S₂O₈. For blood samples, As recoveries by HGAAS range between 95 and 108% for all species when using dry ashing after a pretreatment of samples with HNO₃ and H₂O₂ in a microwave oven. Wet digestion with (NH₄)₂S₂O₈ in a microwave oven gives recoveries very near 100% for As _inorg. and MMA. For other As species in spiked blood samples, recoveries of less than 20% As are found. Precision and detection limits obtained by both techniques are evaluated as well. For arsenic concentrations of 20 μg dm⁻³ or more in blood and urine, a chemical modifier is recommended for GFAAS analysis; it may or may not be proceeded by a mineralization step. For low As levels encountered in the unexposed population, the HGAAS technique provides reliable results only if a very complete mineralization procedure is used.     

A Comparison of Sample Preparation Procedures for the Determination of Iron and Zinc in Bulgur Wheat by Graphite Furnace Atomic Absorption Spectrometry

ABSTRACT

A comparison was made of different digestion methods for the determination of iron and zinc in two types of bulgur wheat prior to their analysis in graphite furnace atomic absorption spectrometry. Samples were digested by means of acid treatment in room temperature, acid treatment at 60°C in a water bath and in a microwave oven and by dry ashing in open ah system. Except for microwave digestion, the samples proved to be unclear. The concentrations of the elements studied in the bulgur samples obtained by the four digestion methods are inconsistent in limits of standard deviations. It was found that aluminum sulfate (4μg/10μl sample) added to the samples acted as a modifier, improving the signal shape and increasing the stability of slurries obtained from digestion procedures.     

ICP-AES法测定润滑油元素含量的前处理方法

准确测定润滑油中元素的含量对于监控润滑油使用性能和预测各种润滑机械故障具有重要的意义。介绍了高温灰化、溶剂稀释、湿法消解、乳化、压力融弹、微波消解6种前处理方法在ICP-AES测定润滑油元素含量中的应用。     

Determination of trace elements by inductively coupled plasma mass spectrometry of biomass and fuel oil reference materials using milligram sample sizes

Most of the analytical techniques used to quantify elements associated with solid samples suffer from high detection limits and cannot be used for trace elements in biomass samples, particularly when only 20 mg are available for analysis. Inductively coupled plasma mass spectrometry (ICP-MS) can achieve detection limits of parts-per-trillion with liquid sample introduction by solution nebulisation. This technique was therefore tested with two standard biomass reference materials: oriental tobacco leaves and cabbage leaves. Two preparations successfully used on coal standards were used to digest the solid samples: a total digestion method (wet ashing digestion) and a partial leaching (microwave extraction). The concentrations of up to seventeen elements (As, Ba, Be, Cd, Co, Cr, Cu, Ga, Mn, Mo, Ni, Pb, Sb, Se, Sn, V and Zn) were measured after the two preparations. The accuracy and sensitivity of the measurements improved when the dilution factor decreased from 5000 to 1000 and to 500. Since the proportion of mineral matter in biomass samples is small (5%), the microwave digestion extracted elements that are generally not completely extracted from coal samples (e.g. Sb). However, some trace element concentrations were below the limit of quantification after microwave extraction, even with a reduced dilution factor (As, Se and Mo) and could not be quantified. A fuel oil was also digested. The trace element concentrations were very low (between 28 and 0.1 microgram g(-1)) but acceptable results were obtained by applying a dilution factor of 100. Only six elements in the fuel oil (As, Ba, Co, Ni, Se and V) had certified or indicated values. Factors affecting the accuracy and sensitivity of the analyses are discussed. The reproducibility of analysis of the tobacco leaf standard was checked over a period of nine months by both digestion methods. The wet ashing method gave acceptable reproducibility for Ba, Cd, Co, Cu, Ga, Mn, Mo, Ni, Pb, V and Zn but poor precision for Cr, Se and Sn and showed evidence of residual chloride interference for As. The microwave extraction gave good reproducibility for As, Ba, Cd, Co, Cr, Cu, Mo, Ni and Zn but poor precision for Se and low recoveries for Ga, Mn, Sn and V. In spite of the small quantities of material analysed, it proved possible to determine the trace elements at levels down to 0.1 microgram g(-1) in the reference materials.     

TXRF法测定松花粉中的9种生命元素

建立了微波消解前处理,全反射X射线荧光法(TXRF)同时测定松花粉中K、Ca、Ti、Mn、Fe、Ni、Cu、Zn和Rb9种生命元素含量的分析方法.松花粉原料经过微波消解前处理后,采用全反射X射线荧光光谱净计数、QXAS分析软件解谱和单一内标法进行定量分析.比较了干灰化法、湿消解法和微波消解法3种前处理方法的效果,并确立微波消解法作为样品前处理方法.用微波消解- TXRF法测定了花粉标准物质中的上述9种元素,并计算得到其仪器检出限(LLD)为0.002～0.054 mg/L,方法检出限(LDM)为0.004～0.122 mg/kg.TXRF法测定各元素的相对标准偏差(RSDs)为1.0％～5.5％.该方法操作简单、样品用量少、检出限低,对实际样品松花粉的测定结果与ICP - MS法无显著性差异.     

Comparison of sample digestion procedures for the determination of arsenic in certified marine samples using the FI-HG-AAS-technique

 High-pressure digestion and a closed-vessel microwave heated system, both employing a mixture of nitric acid and hydrogen peroxide as digesting agent, were tested for decomposing the certified samples of BCR 278 mussel tissue (Mytilus edulis) and of BCR 422 cod muscle to determine arsenic by use of FI-HG-AAS. While the microwave system is insufficient to mineralize arsenic in marine samples (arsenic recoveries of 13±10% in BCR 278, 2±1% in BCR 422; n=4), high-pressure ashing at 300 °C results in recovery percentages of 56±15% (n=4) in mussel tissue (BCR 278) and of 25±10% (n=4) in cod muscle (BCR 422). A dry ashing procedure is given as a reference digestion, yielding complete recoveries of arsenic for both materials. The nitrite interference arising during measurement can be entirely overcome by using an amino sulfuric acid concentration of about 350 mmol/L in the solutions for measurement. Received: 30 April 1996/Revised: 12 July 1996/Accepted: 16 July 1996     

微波消解-ICP-MS测定塑料原料中14种催化剂残留元素

采用微波消解法预处理聚乙烯(PE)、聚丙烯(PP)、聚苯乙烯(PS)、聚对苯二甲酸乙二醇酯(PET)常用塑料原料,使用压力控制装置对消解过程进行监控并对消解条件进行摸索,考察了消解量、消解体系、消解温度和保持时间对消解结果的影响,优化选择了电感耦合等离子体-质谱法(ICP-MS)的测定参数和内标元素。建立了微波消解-电感耦合等离子体-质谱法测定塑料原料中Li、Ca、Mg、Al、Si、Ti、V、Cr、Co、Zn、Ga、Zr、Sb、Hf 14种元素的催化剂残留的检测方法。方法检出限在0.001～10.60μg/L,回收率在82%～120%之间,相对标准偏差小于20%。     

Determination of mineral and trace element concentrations in pine needles by ICP-OES: evaluation of different sample pre-treatment methods

In the present study, the determination of mineral and trace elements (Al, B, Ca, Cu, Fe, K, Mg, Mn, Na, P and Zn) from pine needles using three sample pre-treatment methods followed by inductively coupled plasma optical emission spectrometry, was examined. Sample pre-treatment methods tested were microwave digestion, ultrasound-assisted digestion and dry ashing. The new ultrasound-assisted digestion method was optimised by the analysis of the standard reference material (SRM) 1575a (pine needles) sample. The speed of dry ashing method was significantly increased by ultrasound dissolution after ashing. All the ICP-OES measurements were performed in robust plasma conditions which were tested by measuring the Mg II 280.270 nm/Mg I 285.213 nm line intensity ratios. The microwave digestion resulted generally in slightly higher element concentrations than ultrasound-assisted digestion. B, Cu and Na resulted in such low concentrations that they could not be accurately determined by using the microwave digestion method. The t-tests found no significant differences between the certified and the determined element concentrations of the SRM 1575a using the dry ashing method followed with ultrasound dissolution.     

非完全消化-火焰原子吸收光谱法测定杜仲叶中的微量元素

用非完全消化法处理杜仲叶,在低温下用浓硝酸消解样品,加入乳化剂Triton X-100(OP)溶解消化过程中所产生的油脂,获得均匀的样品乳浊液,取适量的乳浊液制成试液,用火焰原子吸收光谱法快速测定了样品中的微量元素,并对检出限、加标回收率进行了测定。结果表明,相对标准偏差小于2.1%,测定结果与灰化法一致,且相对误差小于±1.8%。用非完全消化法结合火焰原子吸收光谱法对杜仲叶进行预处理取代灰化法是可行的,且方法简便、准确。     

电感耦合等离子体原子发射光谱法测定载钯树脂中钯的前处理方法考察

采用电感耦合等离子体原子发射光谱法(ICP-AES)测定载钯树脂中的钯,对比了灰化法、硝酸-高氯酸法和微波消解法3种前处理方法,考察了称样量、消解加酸量、处理时间和灰化温度等对测定的影响,优化了最佳试验条件,讨论了共存离子的干扰.结果表明,钯质量浓度在0~50 mg/L范围内与强度线性关系良好,线性相关系数为0.999 5,灰化法、硝酸-高氯酸法和微波消解法3种方法的检出限分别为0.002 8、0.005 4、0.002 3 mg/L,相对标准偏差(n=11)分别0.69%、0.63%、0.42%,加标回收率分别为98%~100%、98%~101%、100%~104%.采用3种方法对实际样品进行测定,发现微波消解法处理时间最短,样品处理最完全,检测值最平行.用试验方法与原子吸收光谱法测定同一个载钯树脂,两者测定结果基本相符.     

超级微波消解-电感耦合等离子体发射光谱（ICP-OES）法测定土壤中18种元素

为提高土壤多元素同时检测的效率,采用超级微波消解-电感耦合等离子体发射光谱法测定土壤中钾、钠、钙、镁、铜、铁、锰、锌、磷、硫、硼、砷、镉、铬、铅、钴、镓、锂等18种元素含量。比较了超级微波消解、常规微波消解和电热板消解的处理效果,采用超级微波消解法对样品进行前处理,并优化了消解条件。在最优条件下,各元素的检出限在0.05~20 mg/kg,加标回收率在86.2%~107.5%,RSD在0.1%~3.0%,方法准确度及精密度可以满足多元素同时测定的需求,且该方法具有简单、快速、成本低、用酸量少、重现性好等特点。     

Use of microwave digestion and atomic absorption spectrophotometry to determine chromic oxide as a digestibility marker in feed, feces, and ileal content.

Most conventional digestion procedures, such as dry ashing and wet ashing, are tedious and labor intensive. Microwave digestion is a good alternative, because microwave dissolution is faster, safer, and simpler, and provides more controlled reproducible conditions than conventional methods. The purpose of this study was to develop a microwave digestion method for mineralizing meat and bone meal diets, feces, and ileal contents. Each sample was heated on a hot plate for 10 min, dry ashed at 65 degrees C for 4 h, and transferred into microwave vessels. Then, 10 mL 70% HNO3 was added. Samples were digested for 7, 10, and 20 min at 95, 90, and 85% power, respectively. After the heating cycle, 6 mL 30% H2O2 was added, and samples were returned to the microwave for a second heating cycle of 1 and 7 min at 95% and 90% power, respectively. Finally, chromium concentration was determined by flame atomic absorption spectrophotometry. The digestion method was validated by using a standard reference material, SRM domestic sludge 2781, with a certified chromium value of 195 +/- 9 micrograms/g. The value obtained in this study was 178 +/- 11 micrograms/g, for a difference of 17 micrograms/g. Spike recovery experiments resulted in 103.16 and 100.35% recoveries of chromium from diet and feces samples, respectively. Coefficients of variation were 10.8 and 7.8%, respectively.     

Comparison of dissolution procedures for the determination of cadmium and lead in plastics

Summary A microwave digestion procedure and an oxygen flask combustion procedure were developed for the determination of cadmium and lead in plastic materials. A comparison with conventional wet ashing shows acceptable agreement. Different types of plastics such as polyvinylchloride, polypropylene, polyethylene, polystyrene, polyamide, and polyethyleneterephthalate were investigated. The precision of microwave digestion was determined within a series and from day to day. The results obtained by flame atomic absorption spectrometry were verified by measurement with inverse voltammetry. Overall, microwave digestion as well as oxygen flask combustion are time saving and cost-effective dissolution procedures to supervise the legal cadmium limit in plastics.Abbreviations FAAS Flame atomic absorption spectrometry - GFAAS Graphite furnace atomic absorption spectometry - ICPMS Inductively coupled plasma mass spectrometry - PVC Polyvinylchloride - PP Polypropylene - PE Polyethylene - PS Polystyrene - PET Polyethyleneterephthalate - PA Polyamide 6.6 - PTFE-TFM Polytetrafluoroethylene-tetrafluoromethoxylate - HMDE Hanging mercury drop electrode - MS Mass spectrometry - OFC Oxygen flask combustion - MWD Microwave digestion - CWA Conventional wet ashing - DL Detection limit - QL Quantification limit     

Comparison of partial digestion procedures for determination of Ca, Cr, Cu, Fe, K, Mg, Mn, Na, P, and Zn in milk by inductively coupled plasma-optical emission spectrometry

A fast procedure was developed for determination of Ca, Cr, Cu, Fe, K, Mg, Mn, Na, P, and Zn in milk samples. This procedure consisted of a partial digestion with hydrochloric acid on a hot plate. The results obtained were compared with 3 other digestion procedures (dry ashing and 2 microwave digestions). All the procedures showed similar precision levels, with coefficients of variation <10% for most analyzed elements. Accuracy was evaluated by using certified reference materials, and the values obtained were within the confidence intervals for these products. The results obtained were not considered statistically different. The partial digestion on a hot plate with HCl can be very practical for laboratories with relatively large numbers of sample analyses.