Use of Saccharomyces cerevisiae immobilized in agarose gel as a binding agent for diffusive gradients in thin films

A new binding agent, consisting of the yeast Saccharomyces cerevisiae immobilized in agarose, is proposed for use in diffusive gradients in thin films (DGT). Different gel compositions, containing from 4.5% to 20% (m/v) of S. cerevisiae and 1.5-5.0% (m/v) of agarose, were prepared and tested for uptake of Cd(II). For gels containing 20% (m/v) of S. cerevisiae, a mass of 14,900 ng has been attributed as the uptake limit of Cd for each disk. Determination of the Cd retained in the binding agent was readily carried out using a slurry of the agarose-yeast disk introduced directly into the inductively coupled plasma optical emission spectrometer. The performance characteristics of the DGT samplers, which were assembled with the proposed binding agent (25 mm disk containing 20% of S. cerevisiae and 1.5% of agarose) and a diffusive layer of cellulose (chromatographic paper 3MM Chr of 25 mm diameter), were evaluated by measuring the Cd(II) uptake at various pH values and ionic strengths. Very consistent results were found within the pH range 4.5-7.5 and at ionic strengths ≥0.005 mol L⁻¹. The precision of DGT measurements was characterized by relative standard deviations of <8%. No changes in the uptake of Cd(II) were observed in the samplers that were assembled with recently prepared disks or 35-day-old stored disks. The proposed material has been applied to the analyses of river and sea water samples. For determination of Cd(II), excellent agreement between the results obtained from devices assembled with the proposed material and those assembled with conventional material (Chelex-100 resin) were obtained, strongly validating the use of the agarose-yeast gel disk as a new binding agent for DGT.     

Amperometric sensor for nitrite using a glassy carbon electrode modified with alternating layers of iron(III) tetra-(N-methyl-4-pyridyl)-porphyrin and cobalt(II) tetrasulfonated phthalocyanine

The development of a highly sensitive amperometric sensor for nitrite using a glassy carbon electrode modified with alternated layers of iron(III) tetra-(N-methyl-4-pyridyl)-porphyrin (FeT4MPyP) and cobalt(II) tetrasulfonated phthalocyanine (CoTSPc) is described. The modified electrode showed an excellent catalytic activity and stability for the nitrite oxidation decreasing the peak potentials about 200 mV toward less positive values and presenting much higher peak currents than those obtained on the bare GC electrode. A linear response range of 0.2-8.6 μmol l⁻¹, with a sensitivity of 0.37 μA l μmol⁻¹ and detection limit of 0.04 μmol l⁻¹ were obtained with this sensor. The repeatability of the proposed sensor, evaluated in term of relative standard deviation, was verified to be 1.4% for 10 measurements of 0.2 μmol l⁻¹ nitrite solution. Interference caused by common ions has been investigated in simulated mixtures containing high concentration level of interfering ions and the sensor was found to be tolerant against these ions. The developed sensor was applied for the nitrite determination in water samples and the results were in agreement with those obtained by a comparative method described in the literature. The average recovery for these samples was 100.1 (±0.7)%.     

Chelating resin from functionalization of chitosan with complexing agent 8-hydroxyquinoline: application for metal ions on line preconcentration system

This study describes the functionalization of biopolymer chitosan, using the complexing agent 8-hydroxyquinoline (oxine) by reaction of diazotization. The chelating resin was characterized by degree of deacetylation, infrared, Raman spectroscopy. The efficiency of the chelating resin and accuracy of the proposed method was evaluated by the metal ion recovery technique in the analysis of potable water, lake water, seawater and a certified sample of oyster tissue. The metal ions Cd(II) and Cu(II) in the samples were previously enriched in a minicolumn and flow injection flame atomic absorption spectrometry (FI-FAAS) determined the concentrations of the analytes. The chelating resin exhibited high selectivity for Cd(II) at pH 7 and for Cu(II) at pH 10. The eluent concentration was tested by the use of HNO₃ in concentrations of 0.1-3 mol l⁻¹ maximum response was obtained at 0.5 mol l⁻¹ for Cd(II) and Cu(II), with R.S.D. values of 0.4%. The analytes gave relative standard deviations (R.S.D.) of 1.5 and 0.7% for solutions of Cd(II) and Cu(II), respectively (n = 7) containing 20 μg l⁻¹ of the metal ions, defining a high reproducibility. The limits of detection (LOD) were 0.1 μg l⁻¹ for Cd(II) and 0.4 μg l⁻¹ for Cu(II). The analytical properties of merit were obtained using the parameters previously optimized with preconcentration time of 90 s. The chelating resin showed chemical stability within a wide range of pH and the efficiency was not altered for the preconcentration of the metal ions during all the experiments.     

Application of the diffusive gradients in thin films technique for available potassium measurement in agricultural soils: Effects of competing cations on potassium uptake by the resin gel

The utilization of Amberlite (IRP-69 ion-exchange resin, 100–500 wet mesh) as the binding phase in the diffusive gradients in thin films (DGT) technique has shown potential to improve the assessment of plant-available K in soils. The binding phase has recently been optimized by using a mixed Amberlite and ferrihydrite (MAF) gel which results in linear K uptake over extended deployment periods and in solutions with higher K concentrations. As restriction of K uptake by Ca on the Amberlite based resin gel has been previously proposed, potential competing effects of Ca²⁺, Mg²⁺ and NH₄⁺ on K uptake by the MAF gel were investigated. These cations had no effect on K elution efficiency which was 85%. However, K uptake by the MAF gel was restricted in the presence of competing cations in solution. Consequently, the diffusion coefficient of K decreased in the presence of cations compared to previous studies but was stable at 1.12 × 10⁻⁵ cm² s⁻¹ at 25 °C regardless of cation concentrations. Uptake of K by the DGT device was affected by the presence of excessive Ca in more than 30% of twenty typical Australian agricultural soils. However, this problem could be circumvented by using a shorter deployment time than the normal 24 h. Moderate correlation of concentrations of K extracted by DGT with Colwell K (extracted by NaHCO₃, R² = 0.69) and NH₄OAc K (R² = 0.61) indicates that DGT measures a different pool of K in soils than that measured by the standard extractants used. In addition, the MAF gel has the ability to measure Ca and Mg simultaneously.     

Synthesis and application of a functionalized resin for flow injection/F AAS copper determination in waters

This paper reports the development of a new strategy for low-level determination of copper in water samples by using a flow-injection system coupled to solid-phase extraction (SPE) using flame atomic absorption spectrometry (F AAS) as detector. In order to preconcentrate copper from samples, a minicolumn packed with a styrene-divinylbenzene resin functionalized with (S)-2-[hydroxy-bis-(4-vinyl-phenyl)-methyl]-pyrrolidine-1-carboxylic acid ethyl ester was used and the synthesis procedure is described. System operation is based on the on-line retention of Cu(II) ions at pH 9.0 ± 0.2 in a such minicolumn with posterior analyte elution with 2 mol l⁻¹ HCl directly to the F AAS nebulizer. The influence of several chemical (sample pH, buffer concentration, HCl eluent concentration and effect of the ionic strength) and flow (sample and eluent flow rates and preconcentration time) variables that could affect the performance of this system were investigated as well as the possible interferents. At optimized conditions, for 2 min of preconcentration time (13.2 ml of sample volume), the system achieved a detection limit of 1.1 μg l⁻¹, a R.S.D. 1% at 20 μg g l⁻¹ and an analytical throughput of 25 h⁻¹, whereas for 4 min of preconcentration time (26.4 ml of sample volume), a detection limit of 0.93 μg l⁻¹, a R.S.D. 5.3% at 5 μg l⁻¹ and a sampling frequency of 13 h⁻¹ were reported.     

Factorial design for optimization of experimental variables in preconcentration of copper by a chromotropic acid loaded Q-Sepharose adsorbent

An agarose-based anion exchanger (Q-Sepharose) was loaded with chromotropic acid (CTA) and used for column preconcentration and determination of copper by flame AAS. Preliminary experiments indicated that a sample pH of 5.7-6.5 is best suited for accumulation of copper and a 2.5 ml portion of a 0.02 mol l⁻¹ HCl solution can efficiently desorb the analyte from the column. An incomplete factorial design was used for optimization of five different variables that affect recovery of copper. The results indicated that ionic strength, pH and sample volume variables are the most important effects, respectively. Hence, these variables and their possible interactions were studied more carefully. In optimized conditions, the column could tolerate up to 0.18 mol l⁻¹ sodium nitrate in the matrix. A 5 ml portion of a 0.02 mol l⁻¹ CTA was sufficient for loading of a 0.5 ml column prior to preconcentration of copper from a 150 ml sample solution. Matrix ions of Ca²⁺, Mg²⁺, Na⁺ and K⁺ and potentially interfering ions of Pb²⁺, Ni²⁺, Cd²⁺, Co²⁺, Zn²⁺ and Mn²⁺ with relatively high concentrations did not have any significant effect on the recovery of the analyte. A preconcentration factor of 60 and a detection limit of 1.0 μg l⁻¹ was obtained for the determination of copper by the flame AAS method. A precision better than 2.5%, expressed as R.S.D., was also achieved. Application of the method to tap water and two different river water samples resulted in values well confirmed by direct determinations with ET-AAS.     

Development of the diffusive gradient in thin films technique for the measurement of labile mercury species in waters

The diffusive gradients in thin films (DGT) technique, utilizing resin gel with ion-exchange resin Duolite GT73 and new ion-exchange resin Ambersep GT74, was investigated for the accumulation of four mercury species (Hg²⁺, CH₃Hg⁺, C₂H₅Hg⁺, C₆H₅Hg⁺). The diffusion coefficients of mercury species in agarose gel calculated on the basis of Fick’s Law were mercury species-specific. The diffusion coefficients of Hg²⁺ and CH₃Hg⁺ at 25 °C (9.07 ± 0.23 × 10⁻⁶ cm² s⁻¹ and 9.06 ± 0.30 × 10⁻⁶ cm² s⁻¹, respectively) were very similar, but the diffusion coefficients of C₂H₅Hg⁺ (6.87 ± 0.23 × 10⁻⁶ cm² s⁻¹) and C₆H₅Hg⁺ (3.86 ± 0.19 × 10⁻⁶ cm² s⁻¹) were significantly lower. Influence of experimental conditions (pH, selected cations, chlorides and humic substance) on mercury species accumulation by DGT was studied. The DGT technique was applied to river water spiked with mercury species.     

Synthesis of cross-linked chitosan possessing N-methyl-d-glucamine moiety (CCTS-NMDG) for adsorption/concentration of boron in water samples and its accurate measurement by ICP-MS and ICP-AES

A chitosan resin derivatized with N-methyl-d-glucamine (CCTS-NMDG) was synthesized by using a cross-linked chitosan (CCTS) as base material. The N-methyl-d-glucamine (NMDG) moiety was attached to the amino group of CCTS through the arm of chloromethyloxirane. The adsorption behavior of 59 elements on the synthesized resin was systematically examined by using the resin packed in a mini-column, passing water samples through it and measuring the adsorbed elements in eluates by ICP-MS. The CCTS-NMDG resin shows high ability in boron sorption with the capacity of 0.61 mmol ml⁻¹ (= 2.1 mmol g⁻¹). The sorption kinetics of this resin was faster than that of the commercially available resins. Other advantages of the synthesized resin are: (1) quantitative collection of boron at neutral pH regions; (2) complete removal of large amounts of matrices; (3) no loss of efficiency over prolonged usage; (4) effective collection of boron in wide range concentration using a mini column containing 1 ml resin; (5) complete elution of boron with 1 mol l⁻¹ nitric acid. The resin was applied to the collection/concentration of boron in water samples. Boron in tap water and river water was found to be in the range of 6-8 μg l⁻¹. The limit of detection (LOD) of boron after pretreatment with CCTS-NMDG resin and measurement by ICP-MS was 0.07 μg l⁻¹ and the limit of quantification (LOQ) was 0.14 μg l⁻¹ when the volume of each sample and eluent was 10 ml.     

Application of a cellulose phosphate ion exchange membrane as a binding phase in the diffusive gradients in thin films technique for measurement of trace metals

The technique of diffusive gradients in thin films (DGT) is a newly developed analytical technique capable of measuring in situ concentrations of trace metals in the environment. The technique employs a thin film diffusive hydrogel (with well-defined diffusion properties) in contact with a binding phase capable of binding metal ions of interest. In this work, we demonstrate, for the first time, the use of a commercially available solid ion exchange membrane (Whatman P81) as the binding phase in DGT analysis. The cellulose phosphate-based Whatman P81 membrane is a strong cation exchange membrane. Its performance characteristics as a new binding phase in DGT measurement of Cu²⁺ and Cd²⁺ were systematically investigated. Several advantages over the conventional ion exchange resin-embedded hydrogel binding phases used in DGT were observed including simple preparation, ease of handling, and reusability. The binding capacities of the material to various metal ions were examined both collectively and individually. The binding phase preferentially binds to transition metal ions rather than matrix ions such as potassium, sodium, calcium and magnesium, which are competitive species in natural waters. Within the optimum pH range (pH 4.0-9.0), the maximum non-competitive binding capacities of the membrane for Cu²⁺ and Cd²⁺ were 3.22 and 3.07 μmol cm⁻², respectively. The suitability of the new membrane-based binding phase for DGT applications was validated experimentally. The experimental results demonstrated excellent agreement with theoretically predicted trends. The measurement was not degraded after four consecutive reuses of the cellulose phosphate binding phase.     

Diffusion characteristics of agarose hydrogel used in diffusive gradients in thin films for measurements of cations and anions

The agarose hydrogel has been increasingly used as a diffusive layer in diffusive gradients in thin films (DGT) measurements. However its diffusive characteristics have not been examined in detail. In this study, the performance of agarose gel was tested in DGT measurements of eight cations (Fe(II), Mn(II), Co(II), Ni(II), Cu(II), Zn(II), Pb(II), and Cd(II)) and eight anions (P(V), As(V), Cr(VI), Mo(VI), Sb(V), Se(VI), V(V), and W(VI)). It was found that the thickness of agarose, a key parameter in the calculation of DGT measured concentration, remained unchanged after hydration followed by storage under the following conditions: pH 2–11, ionic strength 0–1.0 M, temperature 4–40 °C, and with the storage time extending to 300 d. Enrichment of cations and repelling of anions were observed in the gel under the ionic strengths of < 2–3 mM and <1 mM (NaNO₃), respectively, which was attributed to the electrostatic interactions of these ions with the fixed negatively charged groups (mainly pyruvate) in the gel. The diffusion coefficients of cations and anions through the agarose gel (plus a PVDF filter membrane) were on average 1.10 ± 0.04 times of the reported diffusion coefficients through the agarose cross-linked polyacrylamide (APA) hydrogel, typically used in DGT technique. The working pH ranges for the agarose gel-assembled DGTs were 4–10 and 5–9 for anions and cations, respectively. The use of agarose gel, either individually or along with different filter membranes, affected the overall diffusion rates of cations and anions. The measured DGT concentrations of cations and anions in filtered natural freshwater and seawater were mostly in line with those measured directly. The results showed that the agarose gel can be used as one of the standard diffusive layers in DGT measurements for a wide range of inorganic and organic analytes.     

Spectrophotometric catalytic determination of Fe(III) in estuarine waters using a flow-batch system

A flow-batch system was developed for the determination of Fe(III) in estuarine waters with high variability in salinity. The method is based on the catalytic effect of iron(III) on the oxidation rate of N,N-dimethyl-p-phenylenediammonium dichloride (DmPD) by hydrogen peroxide and the formed product is spectrophotometrically monitored at 554 nm. A controlled addition of sodium chloride to every assayed sample is accomplished for in-line individual salinity matching.The proposed system processes about 30 samples h⁻¹ and yields reproducible results. Relative standard deviations were estimated as <1.5% after 10 injections of typical samples (10.0-50.0 μg l⁻¹ Fe; ca. 0.5 mol l⁻¹ Cl). Synthetic samples (15.0 μg l⁻¹ Fe; 0.25-1.0 mol l⁻¹ NaCl) were efficiently processed, and no significant differences in results were found at a probability level of 99.7%. The method works for the full range of salinities. Only 120 μg DmPD are consumed per determination. The analytical curve is linear up to about 60 μg l⁻¹ Fe (r>0.999; n=5) and the detection limit is 5 μg l⁻¹ Fe. Results are in agreement with graphite furnace atomic absorption spectrometry.     

Flow injection analysis of ultratrace orthophosphate in seawater with solid-phase enrichment and luminol chemiluminescence detection

Solid-phase extraction technique had been applied to extract molybdophosphoric heteropoly acid (MoP) paired with cetyltrimethylammonium bromide (CTAB) from seawater matrix using C18 sorbent. Chemiluminescence emission could be generated via MoP reaction with alkaline luminol. Based on these, a novel on-line solid-phase extraction method coupled with flow injection (FI) analysis and luminol chemiluminescence detection had been established to determine ultratrace orthophosphate in seawater. The MoP-CTAB compound could be efficiently extracted on an in-line Sep-Pak C18 cartridge, and rapidly eluted by 0.3 mol l⁻¹ sulphuric acid-ethanol solution. Then the compound was reduced by luminol to produce chemiluminescence light, which could be detected using a luminescence analyzer. Experimental parameters were optimized using a univariate experimental design. Using artificial seawater with salinity of 35 as a matrix, the standard curve with a linear range between 0.005 and 0.194 μmol l⁻¹ had been obtained, and the recovery and the detection limit of the proposed method were found to be 92.5% and 0.002 μmol l⁻¹, respectively. The relative standard deviation (R.S.D.), which was determined over eight hour, was 4.66% (n = 7) for the artificial seawater at a concentration of 0.097 μmol l⁻¹ orthophosphate. Si of 200 μmol l⁻¹ would not interfere with the detection of 0.012 μmol l⁻¹ orthophosphate compound. Three typical seawater samples were analyzed using both the proposed method and the magnesium hydroxide-induced coprecipitation (MAGIC) method, and the results of the two methods showed no significant difference using the t test. Compared to the MAGIC method, the proposed method was more sensitive, time saving and easy for on-line analysis.     

Sampling 4-chlorophenol in water by DGT technique with molecularly imprinted polymer as binding agent and nylon membrane as diffusive layer

For the first time, a diffusive gradients in thin films (DGT) device using molecularly imprinted polymer (MIP) as the binding agent and nylon membrane (NM) as the diffusive layer (NM-MIP-DGT) has been developed for sampling 4-chlorophenol (4-CP) in water. The MIP was prepared by precipitation polymerization with methacrylic acid as monomer and ethyleneglycoldimethacrylate as cross-linker. The diffusion coefficient of 4-CP through NM was obtained to be 0.788 ± 0.040 μ cm² s⁻¹ by diffusion cell method. The ratio was 1.01 ± 0.05 (mean ± standard deviation) for the concentration of 4-CP sampled by NM-MIP-DGT and analyzed by HPLC method to the total concentration of 4-CP in the synthetic solution where free 4-CP species dominated. The results showed that NM-MIP-DGT could sample 4-CP in synthetic solution accurately. The performance of NM-MIP-DGT for sampling 4-CP was independent of pH in the range of 3–7 and ionic strength in the range of 0.0001–0.1 mol L⁻¹ NaCl solution. The concentration of free form of 4-CP sampled by NM-MIP-DGT decreased with the increasing concentration of dissolved organic carbon in different water samples due to the electrostatic interaction of natural organic compounds with 4-CP. 1.8 mg L⁻¹ of the free form of 4-CP was determined by HPLC which was sampled by NM-MIP-DGT in an intermediate untreated industrial effluent. The NM-MIP-DGT can be a potential passive tool for sampling the free form of 4-CP in water.     

The use of a gold disc microelectrode for the determination of copper in human sweat

A novel approach of using a gold disc microelectrode to analyze sweat samples for copper ions by anodic square wave stripping voltammetry (SW stripping voltammetry) is described. Sweat was collected from the lower back of four subjects after physical exercise and the sample volume required for the determinations was 100 μL. Under the optimized conditions, the calibration plot was linear over the range 1-100 μmol L⁻¹ Cu(II) with a limit of detection of 0.25 μmol L⁻¹. The precision was evaluated by carrying out five replicate measurements in a 1 μmol L⁻¹ Cu(II) solution and the standard deviation was found to be 1.5%. Measurements were performed by inserting the microelectrode into sweat drops and Cu(II) concentrations in the analyzed samples ranged from 0.9 to 28 μmol L⁻¹. Values obtained by the proposed voltammetric method agreed well with those found using graphite furnace atomic absorption spectroscopy (GFAAS).     

Flow-injection investigation of the chemiluminescent reaction of bis(2,4,6-(trichlorophenyl)oxalate) with free chlorine

This work investigated the chemiluminescent reaction of free chlorine with bis(2,4,6-(trichlorophenyl)oxalate) (TCPO) in the presence of 9,10-diphenylanthracene in acetonitrile/water medium, with analytical application for free chlorine in tap water. In the absence of free chlorine, the background signal increased with the pH and the chemiluminescence emission showed strong dependence with the sample acidity. A flow injection analysis system, for free chlorine determination, was developed. The linear range for free chlorine was (0.2-3.0)×10⁻⁵ mol l⁻¹. Chloramine 1.0×10⁻⁵ mol l⁻¹ and chlorite 1.0×10⁻⁶ mol l⁻¹ also enhanced the chemiluminescence intensity.     

Bia-amperometric quantification of salbutamol in pharmaceutical products

This paper presents a simple, rapid and reproducible method of analysis of salbutamol in pharmaceutical products, utilizing batch injection analysis (BIA) associated with amperometric detection. A study of salbutamol oxidation demonstrated a strong dependence between electrode fouling and pH. All determinations were done utilizing a glassy carbon electrode in presence of 3.0 mol l⁻¹ NaOH. A large linear dynamic range from 8×10⁻⁷ to 2×10⁻⁴ mol l⁻¹ was obtained by using an injected volume of 100 μl with a detection limit of 2.5×10⁻⁷ mol l⁻¹. R.S.D. of 0.92% for 50 successive injections of 4×10⁻⁶ mol l⁻¹ of salbutamol and a sample throughput of 60 samples per hour were achieved. The method was applied for salbutamol quantification in syrups.     

Development and evaluation of a diffusive gradients in a thin film technique for measuring ammonium in freshwaters

A new diffusive gradients in a thin film (DGT) technique, using Microlite PrCH cation exchange resin, was developed and evaluated for measuring NH₄–N in freshwaters. Microlite PrCH had high uptake (>92.5%) and elution efficiencies (87.2% using 2 mol L⁻¹ NaCl). Mass vs. time validation experiments over 24 h demonstrated excellent linearity (R² ≥ 0.996). PrCH-DGT binding layers had an extremely high intrinsic binding capacity for NH₄–N (∼3000 μg). NH₄–N uptake was quantitative over pH ranges 3.5–8.5 and ionic strength (up to 0.012 mol L⁻¹ as NaCl) typical of freshwater systems. Several cations (Na⁺, K⁺, Ca²⁺ and Mg²⁺) were found to compete with NH₄–N for uptake by PrCH-DGT, but NH₄–N uptake was quantitative over concentration ranges typical of freshwater (up to 0.012 mol L⁻¹ Na⁺, 0.006 mol L⁻¹ K⁺, 0.003 mol L⁻¹ Ca²⁺ and 0.004 mol L⁻¹ Mg²⁺). Effective diffusion coefficients determined from mass vs. time experiments changed non-linearly with electrical conductivity. Field deployments of DGT samplers with varying diffusive layer thicknesses validated the use of the technique in situ, allowed deployment times to be manipulated with respect to NH₄–N concentration, and enable the calculation of the diffusive boundary layer thickness. Daily grab sample NH₄–N concentrations were observed to vary considerably independent of major rainfall events, but good agreements were obtained between PrCH-DGT values and mean grab sample measurements of NH₄–N (C_DGT:C_SOLN 0.83–1.3). Reproducibility of DGT measurements in the field was good (relative standard deviation < 11%). Limit of detection was 0.63 μg L⁻¹ (equivalent to 0.045 μmol L⁻¹) based on 24 h deployments.     

New microdialysis-electrochemical device for simultaneous determination of ascorbic acid and 5-hydroxyindole-3-acetic acid in rat striatum

A new device combining microdialysis with electrochemical microsensor was developed. It can be applied to monitor the biomolecules in the brain for biological and pharmaceutical research. In this paper, the device was applied to simultaneously determine ascorbic acid (AA) and 5-hydroxyindole-3-acetic acid (5-HIAA) in rat striatum. The microsensor used for the device was poly (sulphosalicylic acid) microsensor, which exhibited a good electrocatalytic effect on oxidization of AA and 5-HIAA. The oxidation currents measured by differential pulse voltammetry (DPV) were linear for AA in the range of 0.02-1.0 mmol l⁻¹, and for 5-HIAA from 0.5 to 10.0 μmol l⁻¹ (r=0.9998 and 0.9991, respectively). The detection limits were calculated to be 0.01 mmol l⁻¹ for AA and 0.25 μmol l⁻¹for 5-HIAA (S/N=3). Studies also showed that co-existing substances in biological fluids did not interfere with AA and 5-HIAA determination when using this microsensor. Since, the substances in the microdialysate are easily oxidized by air, the microdialysate in this device was under the protection of N₂. It was found that the concentrations of AA and 5-HIAA in rat striatum were 215±5 and 6.21±0.61 μmol l⁻¹ (mean±S.E.M., n=7), respectively with this device under the protection of N₂. In addition, the effect of the nitric oxide donor, sodium nitroprusside (SNP), on 5-HIAA in the rat striatum was investigated. It was found that a high concentration of SNP (1.0 mmol l⁻¹) resulted in a 34% increase in 5-HIAA level.     

Flow injection spectrophotometric method for chloride determination in natural waters using Hg(SCN)(2) immobilized in epoxy resin

A flow injection (FI) spectrophotometric method was proposed for the determination of chloride ion in natural waters. The determination of chloride was carried out by reaction with Hg(SCN)₂ immobilized in an epoxy resin bead in a solid-phase reactor (SPR) and the thiocyanate ions released were determined spectrophotometrically at 480 nm after complexing reaction with Fe(III). The analytical curve for chloride was linear in the concentration range from 5.6 × 10⁻⁵ to 2.2 × 10⁻⁴ mol l⁻¹ with a detection limit of 1.4 × 10⁻⁵ mol l⁻¹. The relative standard deviation (R.S.D.) was 2.2% for a solution containing 2.2 × 10⁻⁴ mol l⁻¹ (n = 10). The simple manifold allows a routine analytical frequency of 100 determinations per hour. The main advantage of the developed method is the 400% reduction of the Hg waste solution generated when compared to conventional methods for chloride determination based on the same spectrophotometric reaction.     

Chemiluminometric photo-induced determination of Strychnine in a Multicommutation flow assembly

This paper deals on the determination of Strychnine, a potent and dangerous pesticide and the analytical procedure is based on the photo-induced chemiluminescence of the pesticide by means of the Multicommutation continuous-flow methodology. Small segments of the pesticide solution were sequentially alternated with segments of the solution for adjusting the suitable medium for the photodegradation. The required time of UV irradiation was obtained by stopped-flow during 150 s; then, the resulting solution formed alternated segments with the oxidizing solution containing 5 × 10⁻³ mol l⁻¹ Ce(IV) in 0.6 mol l⁻¹ nitric acid. The calibration range, from 2 μg l⁻¹ to 50 mg l⁻¹, resulted in a linear behaviour over the range 25 μg l⁻¹ to 20 mg l⁻¹ and fitting the equation: I = 4706x + 624 with a correlation coefficient of 0.9955. The limit of detection was 2 μg l⁻¹ and the sample throughput 15 h⁻¹. After testing the influence of a large series of potential interferents, the method was applied to different kinds of samples.