吡哌酸在玻碳电极上的伏安测定

本文应用线性扫描伏安法，微分脉冲伏安法，循环伏安法对吡哌酸在ＧＣＥ上的伏安行为进行了研究，发现在磷酸盐缓冲溶液中＋１．２Ｖ左右有一氧化峰，ＰＰＡ的浓度２－１００μｇ／ｍｌ与峰电流呈良好的线性关系。测定了胶囊和片剂中ＰＰＡ的含量，ＲＳＤ２．１％，回收率在９７％－１０４％之间，方法操作简单快速。ＰＰＡ在ＧＣＥ上的电极反应属于不可逆过程。     

裸玻碳电极伏安测定甲氰咪胍

提出了裸ＧＣＥ不需任何处理测定甲氰咪胍的方法，浓度在３×１０＾－７－６×１０＾－５ｇ／ｍＬ，范围内与峰电流呈线性关系，ＲＳＤ为２．２％，回收率为９６％－１０２％。该方法操作简便快速，大多数金属离子和多种有机生化物质不干扰测定，方法用于片剂和加标尿样中甲氰咪胍的测定与药典方法对照，获得满意结果，并对电极反应进行了初步探讨。     

活化玻碳电极伏安法测定锰的研究

采用活化玻碳电极(GC)以伏安法对测定锰进行了研究。结果表明:沉积于电极表面的二氧化锰对锰(Ⅱ)的电化学氧化具有自催化作用,活化GC电极可极大地提高测定锰的灵敏度。在0.04mol LNH3 NH4Cl(pH9.0)底液中,锰浓度在6.0×10-8～1.0×10-5mol L范围内成线性关系,检出限为4.0×10-8mol L。用3×10-7mol L锰溶液重复测定9次,RSD为1.6%。     

Voltammetric determination of mercury (II) in aqueous media using glassy carbon electrodes modified with novel calix[4]arene

A novel calix[4]arene derivative containing benzothiazole group was coated on glassy carbon electrode (GCE) and then applied to the recognition of mercury ion. Cyclic and square wave voltammetric results showed that the modified electrode selectively recognizes Hg²⁺ ion in aqueous media. A new anodic stripping peak at −0.3 V (vs. Ag/Ag⁺) can be obtained by scanning the potential from −0.6 to 0.6 V, and the peak currents are proportional to the Hg²⁺ concentration. The modified electrode in a 0.1 M H₂SO₄+0.01 M NaCl solution shows linear voltammetric response in the range of 25-300 μg l⁻¹ and detection limit of 5 μg l⁻¹ (ca. 2.5×10⁻⁸ M). This modified GCE does not present any significant interference from alkali, alkaline and transition metal ions except for Pb²⁺, Ag⁺ and Cu²⁺ ions. Only 500, 50 and 100-fold molar excess of Pb²⁺, Ag⁺ and Cu²⁺ ions, respectively, can lead to voltammetric response comparable with that of Hg²⁺. The proposed method was successfully applied to determine mercury in natural water.     

隐丹参酮的电化学行为及其测定

采用循环伏安法研究隐丹参酮在电极上的电化学行为及建立差示脉冲伏安对其测定的新方法。在pH 4.0乙酸盐缓冲液中,氧化峰电流与隐丹参酮浓度在3.0×10-8~2.0×10-7mol/L范围内呈良好的线性关系,检出限为2.0×10-9mol/L。玻碳电极可有效消除样品中其它组分对隐丹参酮测定的干扰,已用于实际样品中隐丹参酮的直接测定。该方法灵敏度高、检测范围宽。     

Voltammetric Detection of the DNA Interaction with Toluidine Blue

Binding reactions of toluidine blue (TB) with herring fish DNA in pH 6.0 Britton–Robinson (B–R) buffer solution have been investigated by cyclic voltammetry and linear‐sweep voltammetry at a glassy carbon electrode. TB has a couple of well‐defined redox peaks. The addition of DNA into the TB solution resulted in the decrease of the redox‐peak currents and the shift negatively of the anodic peak potential. The values of the electrochemical parameters such as the electron number of the electrochemical reaction, the electron transfer coefficient and the electrochemical reaction standard rate constant in the absence and presence of DNA, as well as the values of binding constant and binding ratio of DNA with TB were obtained. Almost unchanged values of the electrochemical parameters in the absence and presence of DNA show that nonelectroactive complexes were formed when TB interacted with DNA. DNA concentration can be determined by the decrease of the peak current of TB. The binding mode of TB with DNA was discussed.     

磷酸可待因在Nafion修饰玻碳电极上的伏安行为研究及测定

用循环伏安法和微分脉冲吸附伏安法对磷酸可待因在Nafion修饰玻碳电极上的伏安行为进行了研究。结果表明在 0 .1mol/LHCl底液中 ,磷酸可待因在 + 1 .0 6V处 (vs.SCE)产生一良好的氧化峰 ,磷酸可待因浓度在 5 .0× 1 0 - 7～2 .5× 1 0 - 5mol/L范围内与峰电流呈线性关系 ,检出限为 1 .3× 1 0 - 7mol/L。并分别对其单方药和复方药制剂进行了测定     

Voltammetric study of the interaction of lomefloxacin (LMF)–Mg(II) complex with DNA and its analytical application

The voltammetric behavior of the LMF-Mg(II) complex with DNA at a mercury electrode is reported for the first time. In NH₃–NH₄Cl buffer (pH=9.10), the adsorption phenomena of the LMF–Mg(II) complex were observed by linear sweep voltammetry. The mechanism of the electrode reaction was found to be a reduction of LMF in the complex, and the composition of the LMF–Mg(II) complex is 2:1. In the presence of calf thymus DNA (ctDNA), the peak current of LMF–Mg(II) complex decreased considerably, and a new well-defined adsorptive reduction peak appeared at −1.63 V (vs. SCE). The electrochemical kinetic parameters and the binding number of LMF–Mg(II) with ctDNA were also obtained. Moreover, the new peak currents of LMF–Mg(II)–DNA system increased linearly correlated to the concentration of DNA in the 4.00×10⁻⁷–2.60×10⁻⁶ g ml⁻¹ range when the concentrations of LMF–Mg(II) complex was fixed at 5.00×10⁻⁶ mol l⁻¹, with the detection limits of 2.33×10⁻⁷ g ml⁻¹. An electrostatic interaction was suggested by electrochemical method.     

Electrochemical Determination of Anti-Hyperlipidemic Drug Ezetimibe Based on its Oxidation on Solid Electrodes

Ezetimibe is the first of a new class of drugs that selectively inhibits cholesterol absorption in the small intestine and reduces plasma LDL cholesterol. In this study, electrochemical oxidation of ezetimibe was investigated on carbon based electrodes and a single and irreversible peak at both electrodes was observed. A linear response was detected between 2 × 10^?6 and 8 × 10^?5 M with glassy carbon electrode and between 2 × 10^?6 and 2 × 10^?4 M with a boron-doped diamond electrode in 0.1 M H₂SO₄ supporting electrolyte. The proposed methods were successfully applied for the determination of ezetimibe from pharmaceutical dosage forms and human serum samples.     

Electroanalytical characteristics of antipsychotic drug ziprasidone and its determination in pharmaceuticals and serum samples on solid electrodes

Ziprasidone is a psychotropic agent used for the treatment of schizophrenia. Its oxidation was investigated electrochemically at boron-doped diamond and glassy carbon electrodes using cyclic, differential pulse, and square wave voltammetry. The dependence of the peak current and peak potentials on pH, concentration, nature of the buffer, and scan rate were examined. The process was diffusion and adsorption controlled for boron-doped diamond and glassy carbon electrodes, respectively. The possible mechanism of oxidation was discussed with some model compounds that have indole and piperazine oxidations. A linear response was obtained between 8 × 10⁻⁷ and 8 × 10⁻⁵ M for the first peak in acetate buffer (pH 5.5) and between 2 × 10⁻⁶ and 2 × 10⁻⁴ M for the second peak in 0.1 M H₂SO₄ with boron-doped diamond electrode for differential pulse and square wave voltammetric techniques. The reproducibility and accuracy of the proposed methods were found between 0.31 and 1.20, 99.27 and 100.22, respectively. The recovery studies were also achieved to check selectivity and accuracy of the methods. The proposed methods were applied for the determination of ziprasidone from pharmaceutical dosage forms and human serum samples without any time-consuming extraction, separation, evaporation or adsorption steps prior to drug assay except precipitation of the proteins using acetonitrile. The results were statistically compared with those obtained through an established LC-UV technique, no significant differences were been found between the voltammetric and LC methods.     

Voltammetric Detection of Captopril Using Copper(II) and an Unmodified Glassy Carbon Electrode

We report a simple, sensitive, and rapid detection of captopril using copper(II) and a bare glassy carbon electrode with cyclic voltammetry. The captopril is detected by the formation of a copper(II)‐captopril complex that is observed to have a characteristic oxidation potential at+0.24 V vs. Ag/AgCl. It is found that the peak current varies linearly with the concentration of captopril. The linear dynamic range is obtained for a captopril concentration of 1 µM to 10 µM, and the sensitivity is found to be 0.10±0.003 μA μM^?1. Importantly, the low limit of detection (n=3) of 0.10 μM and the precision of 3.2 %, are achieved using a simple, unmodified electrode. This is attributable to in situ adsorption of a copper(II)‐captopril complex on the electrode surface.     

Electrochemical determination of maltol in beverages with glassy carbon electrode and its silica sol-gel modified electrode

The electrochemical behavior of maltol on a glassy carbon (GC) electrode was investigated. The results were applied to differential pulse voltammetric determination of maltol in beverages pretreated by ultrafiltration. Under the optimum experimental conditions, the linear range is 1×10⁻⁵ to 6×10⁻⁴ mol l⁻¹ maltol and the relative standard deviation for 0.4 mmol l⁻¹ maltol is 0.6% (n=9). The detection limit was 5 μmol l⁻¹. Furthermore, silica sol-gel film on GC electrode could be used as suitable selective membrane, which integrated selective membrane on the electrode and substituted for the pretreatment of ultrafiltration. Under the above conditions, maltol was determined by semi-differential linear sweep voltammetry at a silica sol-gel modified GC electrode in the concentration range of 5×10⁻⁶ to 5×10⁻⁴ mol l⁻¹. The detection limit was 2 μmol l⁻¹ and the relative standard deviation for 0.1 mmol l⁻¹ maltol was 0.7% (n=7). The proposed method is of sensitivity, simplicity, rapidness and no contamination. It had been applied to the direct determination of maltol in beverages such as grape wines, drinks and beers without any pretreatment. The results obtained with the present method were satisfactory with those obtained by spectrophotometry. It could be used as a simple and practical method for the determination of the flavor enhancer maltol in beverages.     

辛硫磷在玻碳电极上的伏安行为

在以0.1 mol.L-1氯化钾为支持电解质,pH为2.21的B-R缓冲溶液中辛硫磷于-0.72 V(vs.Ag/AgCl)处产生灵敏的还原峰。当辛硫磷的浓度在4×10-5~8×10-4mol.L-1范围内时,浓度与线性扫描还原峰电流呈线性关系。据此对辛硫磷样品作6次平行测定,测得平均值为3.42%,其RSD为1.7%,回收率为98.6%~103.6%。用线性扫描与循环伏安法探讨了该体系的伏安行为,结果表明,辛硫磷在玻碳电极上的电化学还原机理为不可逆过程。     

Sensitive Voltammetric Response of p‐Nitroaniline on Single‐Wall Carbon Nanotube‐Ionic Liquid Gel Modified Glassy Carbon Electrodes

An ionic liquid (i.e., 1‐butyl‐3‐methylimidazolium hexafluorophosphate, BMIMPF₆)‐single‐walled carbon nanotube (SWNT) gel modified glassy carbon electrode (BMIMPF₆‐SWNT/GCE) is fabricated. At it the voltammetric behavior and determination of p‐nitroaniline (PNA) is explored. PNA can exhibit a sensitive cathodic peak at ?0.70 V (vs. SCE) in pH 7.0 phosphate buffer solution on the electrode, resulting from the irreversible reduction of PNA. Under the optimized conditions, the peak current is linear to PNA concentration over the range of 1.0×10^?8–7.0×10^?6 M, and the detection limit is 8.0×10^?9 M. The electrode can be regenerated by successive potential scan in a blank solution for about 5 times and exhibits good reproducibility. Meanwhile, the feasibility to determine other nitroaromatic compounds (NACs) with the modified electrode is also tested. It is found that the NACs studied (i.e., p‐nitroaniline, p‐nitrophenol, o‐nitrophenol, m‐nitrophenol, p‐nitrobenzoic acid, and nitrobenzene) can all cause sensitive cathodic peaks under the conditions, but their peak potentials and peak currents are different to some extent. Their peak currents and concentrations show linear relationships in concentration ranges with about 3 orders of magnitude. The detection limits are 8.0×10^?9 M for p‐nitroaniline, 2.0×10^?9 M for p‐nitrophenol, 5.0×10^?9 M for o‐nitrophenol, 5.0×10^?9 M for m‐nitrophenol, 2.0×10^?8 M for p‐nitrobenzoic acid and 8.0×10^?9 M for nitrobenzene respectively. The BMIMPF₆‐SWNT/GCE is applied to the determination of NACs in lake water.     

硝基吖啶酮差示脉冲伏安法测定核酸的研究

采用循环伏安法对合成的硝基吖啶酮(NACR)的电化学行为进行研究,建立硝基吖啶酮差示脉冲伏安法测定核酸的新方法。在pH 4.8的PBS缓冲液中,硝基吖啶酮与ctDNA能够相互作用形成超分子复合物,使硝基吖啶酮在0.043 V处的氧化峰电流下降,峰电流的下降值同ctDNA的浓度在5.0×10-5mg/L~6.5×10-6mg/L范围内呈良好的线性关系,检出限为2.0×10-7mg/L,相关系数为0.9974,已用于实际样品DNA的测定,故硝基吖啶酮有望成为一种新型的生物小分子电化学探针。     

Voltammetric study of levomepromazine induced ionic permeability in a model lipid membrane system

The interaction of solid supported liquid films of lipids with levomepromazine is investigated in the present work by voltammetry. It is shown that the levomepromazine penetrates into the films, which results in a readily detectable change of the film permeability to electroactive species. In this respect, possibilities for the employment of supported lipid films as model systems in the research of biomembrane active compounds are briefly discussed.     

Voltammetric behavior of urapidil and its determination at multi-wall carbon nanotube paste electrode

The voltammetric behavior of urapidil was investigated. In pH 6.8 Britton-Robinson buffer, an irreversible oxidation peak of urapidil at 0.62 V (versus SCE) at a multi-wall carbon nanotube paste electrode (MWNT-PE) was observed, which was more sensitive with lower potential than that at the carbon paste electrode (CPE). The oxidation of urapidil was a two-electron and two-proton process with adsorption character. A differential pulse voltammetric method was proposed for the determination of urapidil. The peak current of the oxidation peak of urapidil was linearly with its concentration in a range from 5.0 × 10⁻⁸ to 2.0 × 10⁻⁶ mol/L at open-circuit accumulation for 60 s, with a detection limit of 3.8 × 10⁻⁸ mol/L. The proposed method was employed to determine urapidil in urapidil tablets.     

Electrochemical Behaviour of Carbamazepine in Acetonitrile and Dimethylformamide Using Glassy Carbon Electrodes and Microelectrodes

The electrochemical reduction of carbamazepine in acetonitrile (ACN) and dimethylformamide (DMF) using a glassy carbon electrode and microelectrodes has been studied. The reduction process is consistent with an electrochemical‐chemical mechanism (EC) involving a two electron transfer followed by a first order reaction, as shown by the cyclic voltammetry (CV) and differential pulse voltammetry (DPV). Half‐wave potential, number of electron transferred, diffusion coefficient and rate constant of the associated chemical reaction are reported. Limits of detection (LOD) for DPV are 0.92 and 0.76 µg mL^?1 (3.89×10^?6 mol L^?1 and 3.21×10^?6 mol L^?1) in ACN and DMF, respectively. Precision (%RSD) and recovery (%) values when pharmaceutical compounds (200mg carbamazepine tablets) and spiked plasma samples were tested ranged from 1.09 to 9.04 % and % recoveries ranged from 96 to 104.1 %.     

黄芩甙在玻碳电极上的电化学行为及其应用

用线性扫描伏安法(LSV)、循环伏安法(CV)和常规脉冲伏安法(NPV)等多种电化学方法研究了黄芩甙在玻碳电极上的电化学行为,并建立了尿样和血清样品中黄芩甙的微分脉冲伏安(DPV)测定法。实验结果表明:黄芩甙在玻碳电极上的吸附符合Frumkin吸附等温式,吸附自由能为-35.01kJ mol。采用整体电解法求得电极反应电子数为2,并结合Nernst方程式推导了反应机理。黄芩甙在玻碳电极上预富集后,在4.20×10-10～1.05×10-5mol L范围内分段呈线性关系,对5.60×10-7mol L黄芩甙溶液连续6次测定的RSD=2.0%,检出限为2.8×10-10mol L。     

Electrochemical Characterization and Rapid Voltammetric Determination of Riluzole in Pharmaceuticals and Human Serum

The electrochemical oxidation of riluzole was investigated using cyclic and linear sweep voltammetry. Under optimized conditions, current and concentration showed linear dependence in Britton Robinson buffer at pH 3.00 for boron doped diamond and pH 3.00 phosphate buffers for glassy carbon electrodes. Differential pulse and square wave voltammetry were used for the determination of riluzole levels in serum samples and pharmaceutical formulations. The limit of detections were found as 5.25 × 10^?7 M and 8.26 × 10^?8 M for glassy carbon electrode and 1.78 × 10^?7 M and 8.42 × 10^?8 M for boron-doped diamond electrodes, in serum samples, using differential pulse and square wave methods, respectively.