Optimization of microwave digestion for mercury determination in marine biological samples by cold vapour atomic absorption spectrometry

Optimization of acid digestion method for mercury determination in marine biological samples (dolphin liver, fish and mussel tissues) using a closed vessel microwave sample preparation is presented. Five digestion procedures with different acid mixtures were investigated: the best results were obtained when the microwave-assisted digestion was based on sample dissolution with HNO3-H2SO4-K2Cr2O7 mixture. A comparison between microwave digestion and conventional reflux digestion shows there are considerable losses of mercury in the open digestion system. The microwave digestion method has been tested satisfactorily using two certified reference materials. Analytical results show a good agreement with certified values. The microwave digestion proved to be a reliable and rapid method for decomposition of biological samples in mercury determination.     

Single vessel procedure for acid-vapour partial digestion in a focused microwave: Fe and Co determination in biological samples by ETAAS

A single vessel procedure using a focused microwave oven is proposed for biological sample preparation with nitric acid vapour under atmospheric pressure. A laboratory-made PTFE support vessel equipped with four cups that received the samples was adapted to fit on the microwave glass vessel. Biological samples (30 mg) were directly weighed into these PTFE cups followed by the addition of 150 microliters of water or H2O2. The mixture was exposed to acid vapour stemming from 15 ml of concentrated HNO3 placed in the bottom of the glass vessel. The acid vapour was formed at 115 degrees C and brought about the Co and Fe extraction in 10 and 60 min, respectively. The resulting suspension was diluted with 0.14 mol l-1 HNO3 to a final volume of 1.0 ml, shaken and centrifuged. The supernatant was analysed by electrothermal atomic absorption spectrometry (ETAAS) by placing the cups directly in the autosampler of the spectrometer. This system minimised contamination, and reagent and time consumption and was suitable for Co and Fe determination in biological materials. The accuracy of the proposed method was assessed by using certified reference materials and by comparison with the closed vessel microwave as a comparative technique. Cobalt and Fe recovery was around 82-99%. As an additional advantage, up to 6 samples can be simultaneously prepared in each vessel, thereby improving the sample throughput from 6 to 24, when a 6-cavity focused microwave is used.     

A new procedure for bovine milk digestion in a focused microwave oven: gradual sample addition to pre-heated acid

Milk samples can be efficiently digested using a focused microwave oven, however the conventional procedure of addition of concentrated acids to the liquid sample leads to digestates with elevated acidity and residual carbon concentrations. In this work a focused microwave oven was applied for acid digestion of bovine milk samples using a conventional and an alternative procedure based on gradual sample addition to hot and concentrated acids. A two-level 2³ full factorial design experiment with eight runs was carried out to evaluate the optimum experimental conditions for reducing both the residual carbon and the final acidity of digestates. The three studied parameters were: temperature of the digestion medium for sample addition, addition of sulfuric acid before the sample or during the first step, and number of aliquots of the sample gradually added. The best conditions were attained by adding small aliquots of milk (ten-fold a volume of 0.5 ml added during 5.0 min) to a digestion mixture containing 3.0 ml nitric acid plus 1.0 ml sulfuric acid heated at 105 °C. It was demonstrated that the digestion efficiency of the alternative procedure was better than the conventional procedure, i.e. 98 and 80%, respectively. The alternative procedure was applied for determination of Ba, Ca, Cu, K, Mg, Na, P, and Zn in whole and non-fat bovine milk. The accuracy was proved using two certified reference materials (whole and non-fat milk powder).     

Automatic flow-injection system for the determination of heavy metals in sewage sludge by microwave digestion and detection by inductively coupled plasma-atomic emission spectrometry (MW-ICP/AES)

Results are shown obtained in the optimization of an automatic flow injection system that combines microwave digestion with atomic spectrometric detection (FAAS, ICP/AES) for the determination of heavy metals in sewage sludge. Digestion is performed by preparing a suspension of the sample in 1.5 mol/l HNO(3) and making it flow through a PTFE capillary tube placed inside a conventional microwave oven. The effects of the length and inner diameter of the capillary tube, as well as that of the pumping rate, have been studied in order to find the experimental conditions that allow a quantitative elemental recovery in the shortest period of time possible. The optimization study was carried out on a certified sample (BCR No. 146), and the elements determined were Zn, Cu, Pb, Cd, Ni and Cr. The experimental data (percent recovery vs. digestion time) have been fitted to a mathematical model in order to quantify the influence of each of the variables studied. The optimized procedure (MW-ICP/AES) has been applied to one ordinary and one certified sewage sludge sample. In comparison with the conventional methods of sewage sludge analysis, the one proposed is less time consuming, while being equally precise and accurate.     

Determination of lead in biological samples by use of slurry sampling electrothermal atomic absorption spectrometry

Slurry-sampling electrothermal atomic absorption spectrometry has been applied to the determination of lead in several biological samples (fish and marine algae). The slurries were prepared both by magnetic shaking and microwave-heating and the effect of instrument operating conditions and slurry preparation conditions on the signal were examined. In addition, results from slurry sampling were compared with those obtained by microwave-assisted acid digestion of the same samples and no significant differences were found between them when the analysis of variance (ANOVA) was applied. The between-batch precision of the slurry techniques employed was similar to that for the microwave-assisted digestion procedure; values were always below 6.7%, except for the Dicentrarchus labrax sample for which the value obtained was 9.5% when using slurry magnetic shaking and 7.6% when using the slurry microwave heating. The accuracy of the slurry methodology employed was also evaluated by analysis of two biological reference materials (NIST-1577b and IAEA-V10); percentage recoveries obtained were between 95.6 and 98.5% of the values certified for lead.     

Determination of cobalt in sewage sludge using ultrasonic slurry sampling graphite furnace atomic absorption spectrometry

Cobalt in sludge of domestic and industrial origin, with high iron contents (> 17 g/kg), was determined by slurry sampling graphite furnace atomic absorption spectrometry (GF-AAS). Slurries prepared by ultrasonic stirring were adequately diluted to cover the variation in cobalt content in the sludge samples. The diluent was 5% HNO3. Standard atomisation conditions for cobalt determination were used and no matrix modifier was applied. Slurry sampling GF-AAS results in the sludge were verified by analysing totally digested samples by inductively coupled plasma atomic emission spectrometry (ICP-AES) and by GF-AAS. The procedure was validated by analysing the certified reference material BCR 146 R, a sewage sludge of industrial origin. Recoveries for cobalt in the spiked slurried sludge samples ranged from 92 to 96%, with a relative standard deviation of 10%. Recoveries in the certified sludge using slurry sampling GF-AAS technique were about 103% for a cobalt content of 7.39 mg/kg.     

Application of acetylacetone chelation solid-phase extraction to GFAAS measurements of trace amounts of beryllium in marine organisms.

Trace amounts of Be (0.046-2.59 ng) in a dried marine organism sample (10 mg) could be accurately determined by GFAAS after treating with microwave digestion (HNO3/H2O2) at 85 degrees C for 10 min and using acetylacetone as a chelating agent in the presence of an acetate buffer (pH 6.0). The method detection limit (MDL, 3sigma) for Be was found to be 4.6 ng g(-1); the calibration graph was linear up to 259 ng g(-1). Good recoveries (98.5-105.0%) were obtained for eight marine organism samples (including five fish, one lobster, one oyster, and one algae) with a relative standard deviation (RSD, n = 3) < 3.0%. The proposed method could be applied measurements of Be in various marine organisms.     

Investigation of microwave assisted drying of samples and evaporation of aqueous solutions in trace element analysis

Investigations of microwave assisted drying of sample materials and microwave assisted evaporation of aqueous sample solutions and acidic digestion residues were accomplished by means of special rotors for the microwave digestion system MULTIWAVE. To check the results obtained by microwave assisted drying, the samples were also conventionally dried at 105 degrees C in an oven. The following samples have been dried: 10 g each of meat, fish, apple, cucumber, potato, mustard, yogurt, clay and marl; 1 g each of certified reference material TORT 2 (lobster hepatopancreas), BCR 278 (mussel tissue) and BCR 422 (cod muscle); 500 g garden mould. Microwave assisted drying takes 40 min for organic samples and 30 min for inorganic material. Important is a slow increase of microwave power during the first 20 min. The results agree well with conventional drying at 105 degrees C. Losses of As, Se and Hg have been investigated for 3 CRMs. Only Se shows losses in the range of 20%. Losses of As, Be, Cd, Co, Cr, Cu, Fe, Hg, Li, Mg, Mn, Mo, Ni, Pb, Sb, Se, Sr, Ti, Tl, V and Zn after evaporation of aqueous samples and acidic solutions after wet digestion, respectively, have been investigated. 50 mL aqueous solution was evaporated almost to dryness within 25 min. The recovery of Hg is 40-50%, of Se 90-95% and of the other elements 97-102%. 0.2 g each of TORT 2, BCR 278 and BCR 422 have been digested with 4 mL nitric acid and 1 mL hydrochloric acid by means of the microwave digestion system MULTIWAVE. The digestion residue was evaporated almost to dryness and dissolved again in 10 mL diluted nitric acid. In this case no element losses have been observed. The measured concentration of As, Cd, Cu, Fe, Mn, Hg, Pb, Mo, Ni, Se, Sr, V and Zn agree very well with the certified values. An important prerequisite for good recoveries is not to evaporate the solutions to complete dryness.     

Determination of tin and titanium in soils, sediments and sludges using electrothermal atomic absorption spectrometry with slurry sample introduction

Fast-heating programmes for determining titanium and tin in soils, sediments and sludges using electrothermal atomic absorption spectrometry (ETAAS) with slurry sampling are developed. For titanium determination, suspensions are prepared by weighing 5-40 mg of sample and adding 25 ml of a solution containing 50% (v/v) concentrated hydrofluoric acid. For tin determination, suspensions are prepared by weighing up to 300 mg of sample and then adding 1 ml of a solution containing 25% (v/v) concentrated hydrofluoric acid. Palladium (30 μg) and ammonium dihydrogen phosphate (7% w/v) are used as matrix modifiers for titanium and tin, respectively. Prior mild heating in a microwave oven is recommended for titanium determination. Calibration is carried out using aqueous standards. The tin and titanium contents of a number of samples obtained by using the slurry approach agree with those obtained by means of a procedure based on the total dissolution of the samples using microwave oven digestion. The reliability of the procedures is also confirmed by analysing several certified reference materials.     

Determination of thirteen common elements in food samples by inductively coupled plasma atomic emission spectrometry: comparison of five digestion methods

Five sample digestion procedures were evaluated for the determination of Al, B, Ca, Cu, Fe, K, Mg, Mn, Na, P, S, Sr, and Zn in food samples by inductively coupled plasma atomic emission spectrometry. The 5 procedures include dry ashing at 500 degrees C, wet digestion with HNO3-HClO4, microwave digestion with HNO3, microwave digestion with HNO3-H2O2, and microwave digestion with HNO3-H2O2-HF. For microwave digestion with HNO3-H2O2-HF, silicon (IV) oxide was used to eliminate the excess HF, making it possible to determine total Al, B, and other common elements accurately and simultaneously. Seven National Institute of Standards and Technology standard reference materials (SRMs) were analyzed to compare the recovery of 13 elements with above digestion procedures. The results demonstrated that the microwave digestion procedure with HNO3-H2O2-HF yielded the best recoveries for all 13 elements in the selected SRMs. The determined concentrations of most elements were close for all 3 microwave digestion procedures with the exception of Al in oyster tissue, bovine liver, and spinach. Notably, the wet digestion with HNO3-HClO4 is the simplest and the most effective procedure for the selected elements except Al and B. Although there are several concerns with the dry ashing procedure, it might be a preferable procedure for those analyses where only nonvolatile elements are to be determined and the concentrations of the elements are low.     

Determination of cadmium and lead in biological samples by three ultrasonic-based samples treatment procedures followed by electrothermal atomic absorption spectrometry

The development of 3 different ultrasonic-based sample treatment methods, ultrasonic probe-assisted acid extraction, ultrasonic-assisted acid slurry, and ultrasonic-assisted acid pseudodigestion is presented. These methods were compared for the determination of Cd and Pb by electrothermal atomic absorption spectrometry in biological samples (blood and scalp hair) and validated by using certified materials BCR 397 human hair and BCR 185R bovine liver. The sample amounts chosen to perform the analysis were 100 mg and 0.5 mL for solids (human hair and bovine liver) and blood samples, respectively. An acid digestion induced by microwave energy was used to obtain the total metal concentrations and for comparative purposes. The best results were obtained with the ultrasonic-assisted acid pseudodigestion, with which it was possible to perform accurate and precise determination of the Cd and Pb contents in 2 certified reference materials and biological samples of 50 normal males of ages 25-40 years. The precision of the methods, together with their efficiency, rapidity, low cost, and environmental acceptability, make them good alternatives for the determination of trace metals from biological samples. The precision of the methods for accuracy evaluation, resulting in good agreement according to the t-test for a 95% confidence level, and the relative standard deviations were lower than 10% (n=10) for all determinations.     

Optimization of digestion methods for sewage sludge using the Plackett-Burman saturated design

The Plackett-Burman saturated factorial design was used to select optimized dissolution conditions for sewage sludge samples. Three different digestion methods were applied: i) microwave oven digestion in a domestic oven with Parr-type reactors; ii) microwave oven digestion with controlled-pressure reactors; iii) pressure bomb reactor heated on a hot plate. The three methods were validated by statistically comparing the metal contents found with the certified ones of the sewage sludge sample (BCR 145R). No significant differences were obtained and the RSD values were lower than 3% in all cases. The metals were determined by flame-AAS. The variables studied were the following: microwave power; digestion time; predigestion; volume of hydrochloric acid; volume of hydrofluoric acid; volume of nitric acid. The operative advantages offered by microwave digestion with controlled-pressure reactors were also considered. Received: 23 July 1997 / Revised: 31 October 1997 / Accepted: 5 November 1997     

Optimization of digestion methods for sewage sludge using the Plackett-Burman saturated design

The Plackett-Burman saturated factorial design was used to select optimized dissolution conditions for sewage sludge samples. Three different digestion methods were applied: i) microwave oven digestion in a domestic oven with Parr-type reactors; ii) microwave oven digestion with controlled-pressure reactors; iii) pressure bomb reactor heated on a hot plate. The three methods were validated by statistically comparing the metal contents found with the certified ones of the sewage sludge sample (BCR 145R). No significant differences were obtained and the RSD values were lower than 3% in all cases. The metals were determined by flame-AAS. The variables studied were the following: microwave power; digestion time; predigestion; volume of hydrochloric acid; volume of hydrofluoric acid; volume of nitric acid. The operative advantages offered by microwave digestion with controlled-pressure reactors were also considered. Received: 23 July 1997 / Revised: 31 October 1997 / Accepted: 5 November 1997     

Investigation of microwave assisted drying of samples and evaporation of aqueous solutions in trace element analysis

Investigations of microwave assisted drying of sample materials and microwave assisted evaporation of aqueous sample solutions and acidic digestion residues were accomplished by means of special rotors for the microwave digestion system MULTIWAVE. To check the results obtained by microwave assisted drying, the samples were also conventionally dried at 105?°C in an oven. The following samples have been dried: 10 g each of meat, fish, apple, cucumber, potato, mustard, yogurt, clay and marl; 1 g each of certified reference material TORT 2 (lobster hepatopancreas), BCR 278 (mussel tissue) and BCR 422 (cod muscle); 500 g garden mould. Microwave assisted drying takes 40 min for organic samples and ¶30 min for inorganic material. Important is a slow increase of microwave power during the first 20 min. The results agree well with conventional drying at 105?°C. Losses of As, Se and Hg have been investigated for ¶3 CRMs. Only Se shows losses in the range of 20%. Losses of As, Be, Cd, Co, Cr, Cu, Fe, Hg, Li, Mg, Mn, Mo, Ni, Pb, Sb, Se, Sr, Ti, Tl, V and Zn after evaporation of aqueous samples and acidic solutions after wet digestion, respectively, have been investigated. 50 mL aqueous solution was evaporated almost to dryness within 25 min. The recovery of Hg is 40–50%, of Se 90–95% and of the other elements 97–102%. 0.2 g each of TORT 2, BCR 278 and BCR 422 have been digested with 4 mL nitric acid and 1 mL hydrochloric acid by means of the microwave digestion system MULTIWAVE. The digestion residue was evaporated almost to dryness and dissolved again in 10 mL diluted nitric acid. In this case no element losses have been observed. The measured concentration of As, Cd, Cu, Fe, Mn, Hg, Pb, Mo, Ni, Se, Sr, V and Zn agree very well with the certified values. An important prerequisite for good recoveries is not to evaporate the solutions to complete dryness.     

Digestion of biological materials using the microwave-assisted sample combustion technique

In this study a procedure for sample digestion based on sample combustion assisted by microwave radiation is proposed. Combustion is started by microwave radiation in the presence of oxygen under pressure using ammonium nitrate as aid for ignition. The system was adapted in a microwave oven with quartz closed vessels. A quartz piece is used simultaneously as a sample holder and as protection to the cap of quartz vessel from the flame generated in the combustion process. Sample was pressed into a pellet and placed on a disc paper in the holder and 50 μl of 50% m/v ammonium nitrate solution was added. The influence of the absorption solution (diluted and concentrated nitric acid or water) on the recoveries for Cu and Zn was evaluated. About 3 s of microwave irradiation was necessary to start the combustion. The combustion process was evaluated in relation to the influence of sample mass on the ignition time, combustion time and maximum operation pressure. Bovine liver, milk powder and oyster tissue certified reference materials were used to evaluate the accuracy of the procedure for determination of copper and zinc. Good agreement for zinc (96% to 103%) was obtained from bovine liver certified reference material when microwave combustion and microwave combustion followed by reflux were used to sample decomposition, even if water was used for absorption of analyte. For copper, the combustion followed by reflux of 5 min allows an agreement from 96% to 100%. Similar results were obtained for oyster tissue samples. However, for milk powder good agreement close to 100% was obtained only if 4 mol l^− 1 HNO₃ was used with a reflux step. Results from the proposed procedure were also compared to those from conventionally used procedures for biological samples decomposition, such as wet digestion in open vessels and microwave-assisted digestion in closed vessels. The advantages of this procedure include the complete sample decomposition in less time than other procedures and the acid consumption was always lower than 2%. Another advantage is the low residual carbon content, less of 1.4% without reflux and less than 0.3% with the reflux step and the possibility of use of diluted acid as absorbing solution. Moreover, the new holder allows an effective protection of the vessel cap to burnt high masses.     

Sulfur-nanoparticle-based method for separation and preconcentration of some heavy metals in marine samples prior to flame atomic absorption spectrometry determination

The application of sulfur-nanoparticle-loaded alumina as an efficient adsorbent for the solid-phase extraction (SPE) and determination of trace amounts of Cd, Cu, Zn, and Pb ions was investigated in marine samples using flame atomic absorption spectrometry (FAAS). The nanometer-sized sulfur particles were synthesized in situ, physically loaded onto alumina microparticles, and the parameters influencing the preconcentration of the analytes, such as the pH, solution flow rate and volume, eluent solution, and interfering ions, were examined. The results showed that the optimal conditions for quantitative recovery of the metal ions by adsorption and elution on the sulfur nanoparticles (SNPs) was achieved by employing a flow rate of 15 mL min(-1), a pH of 8.5 for the sample solutions, and an eluent composed of 3.0 mol L(-1) HNO(3) in methanol. The detection limits of this method for Cd, Zn, Cu, and Pb ions were 0.30, 0.21, 0.24, and 0.63 μg L(-1) (n=10), respectively. Application of the proposed method to the analysis of fish certified reference material (DORM-3) produced results that were in good agreement with the certified values. The proposed method was also successfully applied to the determination of analytes in marine samples, including seawater, fish, and oysters.     

Comparison of microwave digestion procedures for the determination of some elements in asphaltite ash using ICP-AES

A microwave digestion procedure for asphaltite ash was developed in an attempt to facilitate routine analysis and obtain reproducible conditions or comparable results. The conditions of the most effective procedure for 0.1 g asphaltite ash samples are 1 ml of HNO3 + 3 ml of HCl + 1 ml of HF + 1 ml of deionized water as acid mixture and 15 min for digestion time. The digestion was accomplished in five stages applying continuously 90% to 20% of the microwave power and 20 to 100 psi of the pressure for 10 min of total time. Concentrations of selected elements, Cr, Co, Fe, Mn, Ni and Zn were measured using inductively coupled plasma-atomic emission spectroscopy. The proposed method of digestion provided precise results with relative standard deviations generally less than 3% for investigated elements. Results for fly ash as standard reference material was in good agreement with certified values.     

Comparison of four microwave digestion methods for the determination of selenium in fish tissue by using hydride generation atomic absorption spectrometry

Four microwave digestion methods of fish tissue for selenium determination by hydride generation atomic absorption spectrometry were compared, in which potassium hexacyanoferrate(III) was chosen as a masking agent for eliminating matrix interferences. The results showed that the methods employing HNO(3)/H(2)O(2), HNO(3)/K(2)S(2)O(8)/H(2)O(2) and HNO(3)/H(3)PO(4)/H(2)O(2) digestion media were unreliable. However, the decomposition using the digestion media of HNO(3)/H(2)SO(4)/H(2)O(2) enabled adequate digestion of fish tissue and retention of selenium in a state amenable for determination. Therefore, the digestion procedures with HNO(3)/H(2)SO(4)/H(2)O(2) media are proposed for the determination of selenium in fish tissue by hydride generation atomic absorption spectrometry. The recoveries of the spiked samples investigated ranged from 90 to 102%. The result obtained from analyzing the NIES CRM No. 6 mussel was in good agreement with the reference value (reference value: 1.5 mug/g; found: 1.45 +/- 0.05 mug/g). The limit of detection for selenium was 0.03 mug/g dry mass for a 100 mg sample. The contents of selenium in local fish species investigated ranged from 0.49 to 2.90 mug/g, and the relative standard deviation for the determination of selenium was less than 8%.     

Microwave-assisted double insert vapour-phase digestion of organic samples

A microwave-assisted double insert multimode vapour-phase digestion method was developed for the digestion of organic samples. The experimental set-up was based on a third generation-type teflon microwave vessel, equipped with an automatic pressure regulating type vessel cover. A borosilicate glass holder insert, containing a smaller quartz sample insert, was fitted inside the vessel. Sulphuric acid was added to the holder insert as a microwave absorbing and temperature transferring liquid, which transferred heat to the sample insert (into which the sample was weighed) and charred the sample material. Oxidation of the sample material was carried out simultaneously with charring using nitric acid vapour, which was generated by the 1:1 (v/v) sulphuric acid-nitric acid mixture located in the bottom of the microwave vessel. This set-up generated high digestion efficiency, without any of the interferences normally associated with direct sulphuric acid usage. The method was used for determining the concentrations of Cd, Cr, Cu, Mn, Mo, Zn and Fe in certified organic reference materials using ICP-OES instrumentation. The certified organic reference materials were NRCC DOLT-2 dogfish liver, NIST-SRM 1577b bovine liver and IRMM VDA cadmium in polyethylene No. 001 and No. 004. The results were in good agreement with the certified values, forepart from Cd. For Cd the results were lower than the certified values due to volatilization losses. Sample materials that could not be digested by an earlier procedure were completely digested during a single-step, 30 min digestion. The tested sample materials included certified reference materials, 3-nitrobenzoic acid (3-NBA) and pike (Esox lucius) muscle. The residual carbon concentrations in the digestion solutions were below the detection limit of the TOC instrument. This type of digestion method is described here for the first time in the literature.     

Multi-element analysis by inductively coupled plasma optical emission spectrometry of airborne particulate matter collected with a low-pressure cascade impactor

A method was developed for the elemental analysis of size segregated particles ranging from 0.03 to 10 microns. Sampling and analysis problems are discussed in this paper. Particles were collected with a Dekati low-pressure cascade impactor. PTFE filters coated with oleic acid were used as substrate. Particles were microwave digested in closed vessels. The optimum digestion mixture was composed of HNO3 (1 mL), HF (50 microL) and H2O (1 mL). The optimal power setting and digestion time were studied in order to achieve an efficient digestion. A ca. 35 min microwave digestion cycle at a 650 W maximum power allowed complete digestion of the samples. Special emphasis was placed on the pressure in the closed vessels to avoid sample losses. Solution samples were analysed by inductively coupled plasma optical emission spectrometry using an ultrasonic nebuliser for 18 elements (Al, Ba, Ca, Cd, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, S, Sr, Ti, V, Zn). This procedure was tested with NIST Standard Reference Material 1648 Urban Particulate. Recoveries for certified elements ranged from 95 to 105% except for Al (90%). The influence of cascade impactor materials was investigated with 44 field samples. Strong artefacts due to contamination were shown for analysis at environmental concentrations of Al, Cr, Mn and Ni.