Hierarchical helical assembly of conjugated poly(3-hexylthiophene)-block-poly(3-triethylene glycol thiophene) diblock copolymers

We report on the solution-state assembly of all-conjugated polythiophene diblock copolymers containing nonpolar (hexyl) and polar (triethylene glycol) side chains. The polar substituents provide a large contrast in solubility, enabling formation of stably suspended crystalline fibrils even under very poor solvent conditions for the poly(3-hexylthiophene) block. For appropriate block ratios, complexation of the triethylene glycol side chains with added potassium ions drives the formation of helical nanowires that further bundle into superhelical structures.     

Interfacial properties of free-standing poly(3-hexylthiophene) films

Using full atomistic classical molecular dynamics simulations, the interfacial properties of free-standing poly(3-hexylthiophene) (P3HT) films have been investigated. The orientations of different parts of the P3HT chain and the surface tensions of the films were calculated in a temperature range of 540 K-600 K. At the liquid/vacuum interface, the P3HT chain shows ordering by exposing hexyl groups at the interface, while the chain backbone lays flat with the thiophene ring preferentially tilt toward the surface. At the interface, the terminal methyl groups of hexyl side chains are in excess compared to the methylene groups or thiophene rings. The surface tension of P3HT in its melt state shows similar temperature dependence to that of polymers that have long alkyl side chains. The surface tension values are comparable to those polymers that expose methyl or methylene groups on the surface. The surface tension values determined for the melt state are lower than the experimental reported values for crystalline P3HT films, as expected.     

Air-tolerant poly(3-hexylthiophene) synthesis via catalyst-transfer polymerization

The discovery of catalyst-transfer polymerization and its further developments have led to unprecedented control over the length and sequence of conjugated polymers. However, the methods themselves are technically challenging to perform due to the air- and moisture-sensitivities of the monomers and catalysts. Herein, we report a catalyst-transfer polymerization method that affords poly(3-hexylthiophene) in high yields without using an inert atmosphere. The synthesis capitalizes on a rapid Negishi cross-coupling using a moisture-tolerant organozinc monomer mediated by an air-stable Pd precatalyst. This simple method should make conjugated polymer synthesis more accessible to a broader range of researchers and may be generalizable to other monomer scaffolds.     

Semicrystalline morphology in thin films of poly(3-hexylthiophene)

The thermodynamic phase behavior and the morphology in thin films of poly(3-hexylthiophene) (P3HT) has been studied using calorimetry, X-ray scattering, and scanning force microscopy (AFM). Around 225 °C a phase transition from the crystalline state to a layered, liquid crystalline structure occurs in regioregular P3HT, while the regiorandom counterpart material is disordered at all temperatures and displays a glass transition temperature T_g–3 °C. Regioregular P3HT is semicrystalline and forms needle or plate like crystallites which in solution cast thin films are oriented with respect to the substrate. Films produced by spin coating display a non-equilibrium structure with reduced order and orientation. Annealing of these films in the liquid crystalline state leads to the formation of a morphology similar to the one observed in solution cast films.

Surface-induced conformational changes in poly(3-hexylthiophene) monolayer films

With the aim of elucidating the surface-induced molecular ordering in regioregular poly(3-hexylthiophene) (P3HT) monolayer films, we have controlled the intermolecular interactions at the interface between P3HT and the insulator substrate by using self-assembled monolayers (SAMs) functionalized with two kinds of groups (-NH2 and -CH3). We have found that, depending on the surface properties of such modified insulator substrates, the P3HT chains in the monolayer films can adopt two different conformations (edge-on and face-on). This surprising variation in chain conformation arises because of the specific interactions of the P3HT chains with the modified insulator substrates, which can be explained in terms of the following factors: the unshared electron pairs of the SAM end groups (in the -NH2 system), the pi-H interactions between the thienyl backbone bearing pi systems and the H (hydrogen) atoms of the SAM end groups, and interdigitation between the alkyl chains of P3HT and the alkyl chains of the SAMs (in the -NH2 system).     

Uniaxial alignment of poly(3-hexylthiophene) nanofibers by zone-casting approach

The preparation of large area coverage of films with uniaxially aligned poly(3-hexylthiophene)(P3HT) nanofibers by using zone-casting approach is reported.The length and the orientation of the nanofibers are defined by the solubility of the solvent,the P3HT molecular weight and the substrate temperature.The length of the oriented nanofibers could be increased from 1 μm to more than 10 μm by adding poor solvent into the P3HT solution.It is found that for P3HT of relatively low molecular weight,a solvent with relatively low solubility has to be chosen to get the oriented film.While for the high molecular weight P3HT,the solvent with a relatively high solubility has to be used.The well-aligned film could be obtained because of the solute concentration gradient in the region where the critical concentration is reached during the zone-casting process.Particularly,the solvent evaporation rate and crystallization rate must be chosen properly to satisfy the stationary conditions above,which were controlled by an appropriate choice of solvent and substrate temperature.The film prepared by zone-casting approach had microcrystalline P3HT domains with more inter-chain order than spin-coating film.Meanwhile,the P3HT π-π stacking direction was parallel to the alignment direction of the nanofibers.     

Structure of friction-transferred highly oriented poly(3-hexylthiophene) thin films

Oriented thin films of P3HT were obtained by a friction-transfer technique. The morphology and structure of the film were studied by means of optical microscopy, atomic force microscopy and transmission electron microscopy. Optical microscopy observation indicates that large size well-ordered P3HT thin films can be produced by a friction-transfer technique. Highly ordered lamellae were observed in P3HT friction-transferred films by electron microscopy. Electron diffraction results confirm the existence of high orientation with the a- and c-axes of P3HT crystals aligned in the film plane while the c-axis parallel to the friction-transfer direction. The atomic force microscopy observation of the as-prepared P3HT thin film shows, however, a featureless top surface morphology, indicating the structure inhomogeneity of the obtained film. To get highly oriented P3HT thin films with homogenous structure, high temperature annealing, solvent vapor annealing and self-seeding recrystallization of the friction-transferred film were performed. It is confirmed that solvent vapor annealing and self-seeding recrystallization methods are efficient in improving the surface morphology and structure of the frictiontransferred P3HT thin film. Highly oriented P3HT films with unique structure can be obtained through friction-transfer with subsequent solvent vapor annealing and self-seeding recrystallization.     

Solvent evaporation induced liquid crystalline phase in poly(3-hexylthiophene)

We report on the evolution of the chain orientation of a representative π-conjugated polymer, poly(3-hexylthiophene) (P3HT), during the solution-casting process, as monitored using polarized Raman spectroscopy. These measurements point to the formation of a liquid-crystalline phase of P3HT solutions within a specific time period during solvent evaporation, which leads to a conducting channel. These conclusions are based on the angular dependence of polarized Raman scattering peaks, the anisotropy in the fluorescence background signal, analysis of the scattering-peak shape, and direct observations of the three-phase contact line in an optical microscope under crossed polarizers. These results shed new light on the evolution of chain alignment and thus materials nanostructure, specifically in solution-processed P3HT and more generally in π-conjugated systems. They may further enable the design of improved materials and processes for this important class of polymers.     

Control of the interchain pi-pi interaction and electron density distribution at the surface of conjugated poly(3-hexylthiophene) thin films

Interchain interaction, i.e., pi-pi stacking, can benefit the carrier transport in conjugated regio-regular poly(3-hexylthiophene) (P3HT) thin films. However, the existence of the insulating side hexyl chains in the surface region may be detrimental to the charge transfer between the polymer backbone and overlayer molecules. The control of the molecular orientation in the surface region is expected to alter the distribution of the pi electron density at the surface to solve such problems, which can be achieved by controlling the solvent removal rate during solidification. The evidence that the pi-electron density distribution at the outermost surface can be controlled is demonstrated by the investigation using the powerful combination of near edge X-ray absorption fine structure spectroscopy, ultraviolet photoelectron spectroscopy, and the most surface-sensitive technique: Penning ionization electron spectroscopy. From the spectroscopic studies, it can be deduced that the slower removal rate of the solvent makes the polymer chains even at the surface have sufficient time to adopt a more nearly equilibrium structure with edge-on conformation. Thus, the side hexyl chains extend outside the surface, which buries the pi-electron density contributed from the polymer backbone. Contrarily, the quench of obtaining a thermo-equilibrium structure in the surface region due to the faster removal of the solvent residual can lead to the surface chain conformation without persisting to the strong bulk orientation preference. Therefore, the face-on conformation of the polymer chain at the surface of thin films coated with high spin coating speed facilitate the electron density of the polymer backbone exposed outside the surface. Finally, thickness dependence of the surface electronic structure of P3HT thin films is also discussed.     

电场极化调控聚(3-己基噻吩)薄膜润湿性

本文首次采用电场极化技术精确控制共轭聚合物P₃HT薄膜表面的润湿性,通过调节极化条件,成功实现了对P₃HT薄膜表面润湿性的精确控制,薄膜表面水接触角可以实现从疏水性到亲水性的转变.通过光谱学、形貌学及接触角等表征手段,详细研究了电场极化作用下共轭聚合物分子取向聚集形态及作用机理.该工作不但扩展了共轭聚合物薄膜材料的应用范围,也为分子形态学的研究奠定了基础.     

Time-temperature superposition for viscoelastic properties of regioregular poly(3-hexylthiophene) films

Shear moduli were determined for chemically polymerized and solvent cast regioregular poly(3-hexylthiophene) films, using thickness shear mode acoustic wave resonators. The results are strikingly different to those for electropolymerized regiorandom poly(3-hexylthiophene) films. The time scale of the measurement was varied directly by use of higher harmonics of the acoustic wave resonator and indirectly via temperature. The significant variations in shear modulus with effective time scale can be "normalized"onto a stress master relaxation curve by using the concept of time-temperature superposition; this is the first time this has been demonstrated for electroactive films. The shift factors required to effect this normalization do not follow the classical Williams-Landel-Ferry (WLF) equation developed for long-range backbone motions of bulk polymers. Instead, they follow an Arrhenius-like behavior, commonly used to describe secondary motions of polymer side-chains. The activation enthalpy associated with this is independent of applied potential, is the same as for as cast (undoped) films, and is similar to that for rotation about a carbon-carbon single bond. These all point to the hexyl side-chains as the origins of the observed phenomena, consistent with the "melting point" separating two temperature-dependent phases and with the different molecular packing arrangements that would necessarily apply to regioregular and regiorandom materials.     

The mechanism of photo- and thermooxidation of poly(3-hexylthiophene) (P3HT) reconsidered

Poly(3-hexylthiophene) (P3HT) has been the focus of great interest as it is widely used in organic solar cells. However, P3HT has relatively poor photochemical and thermal stability under ambient atmosphere, which leads to a reduced lifetime of the solar cells. It was therefore necessary to study the photo- and thermooxidation of P3HT. Thin P3HT films were exposed to UV-visible light irradiation and thermal ageing, both in the presence of air. Changes in the infrared spectra of the aged samples were recorded, and the oxidation products were identified. A degradation mechanism that accounted for the modifications in the infrared spectra was then developed. This mechanism confirmed that singlet oxygen plays no decisive role, as previously reported. Oxidation was shown to involve the radical oxidation of the n-hexyl side-chains and the subsequent degradation of the thiophene rings. The breaking of the macromolecular backbone resulted in a loss of π-conjugation, provoking the bleaching of the sample.     

Head-to-tail regioregularity of poly(3-hexylthiophene) in oxidative coupling polymerization with FeCl3

We investigated a head-to-tail regioregularity of poly(3-alkylthiophenes) from 3-alkylthiophene by an oxidative coupling polymerization, which is the simplest and easiest way for the synthesis of polythiophenes. The polymerizations were conducted using ferric chloride (III) as an oxidant in chloroform. Investigating the polymerization conditions, a lower temperature and a lower concentration were effective for increasing the head-to-tail (HT) content. The best HT content of 88% was obtained when the temperature was −45°C and the initial monomer concentration was 0.02 mol L⁻¹. Washing the resulting polymer by n-hexane further increased the content to 91%. Thus, it was found that the high regioselectivity can be achieved by the simple polymerization and the simple operation such as washing. The polymerization mechanism causing the regularity is also discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1943–1948, 1999     

Influence of the microstructure on the photooxidative degradation of poly(3-hexylthiophene)

The influence of the microstructure of poly(3-hexylthiophene) (P3HT) on its photodegradation upon exposure to UV-visible light was studied. High-regioregular (>98%) and low-regioregular (<95%) P3HTs with different molecular weights, dispersities and purities were submitted to irradiation under accelerated artificial ageing conditions. While the molecular weight had no effect on the photodegradation rate, a linear relationship was observed between the photodegradation rate and the regioregularity. The higher photo-instability of low-regioregular P3HTs, which have low crystalline phase content, could be due to the fact that the radical chain oxidation occurs predominantly in the amorphous phase of the polymer. Low-regioregular P3HTs also have a higher number of impurities, especially Fe residues, which are well known for their photocatalytic effect. The results also show that, at low concentrations, oxidation products are able to quench the singlet state of P3HT by acting as electron traps, and that the shortest wavelengths of solar light are the most harmful. Finally, the photooxidation of P3HT leads to the formation of low-molecular-weight carboxylic acids that can easily diffuse and migrate out of low-regioregular P3HT thin films. These results are therefore relevant to the preparation, storage and lifetimes of P3HT-based organic solar cells.     

The influence of poly(3-hexylthiophene) regioregularity on fullerene-composite solar cell performance

A comparison of three samples of poly(3-hexylthiophene) having regioregularities of 86, 90, and 96% is used to elucidate the effect of regioregularity on polymer-fullerene-composite solar cell performance. It is observed that polymer samples with lower regioregularity are capable of generating fullerene composites that exhibit superior thermal stability. The enhanced thermal stability of the composites is attributed to a lower driving force for polymer crystallization in the less regioregular polymer samples, which is supported with two-dimensional grazing incidence X-ray scattering and differential scanning calorimetry measurements. Furthermore, it is demonstrated that all three polymer samples are capable of generating solar cells with equivalent peak efficiencies of approximately 4% in blends with [6,6]-phenyl-C61-butyric acid methyl ester. While it may be non-intuitive that polymers with lower regioregularity can exhibit higher efficiencies, it is observed that the charge-carrier mobility of the three polymers is on the same order of magnitude (10(-4) cm2 V(-1) s(-1)) when measured from the space-charge-limited current, suggesting that highly regioregular and crystalline polythiophenes are not required in order to effectively transport charges in polymer solar cells. Overall, these results suggest a design principle for semicrystalline conjugated polymers in fullerene-composite solar cells in which crystallization-driven phase separation can be dramatically suppressed via the introduction of a controlled amount of disorder into the polymer backbone.     

Improved efficiency of photovoltaics based on CdSe nanorods and poly(3-hexylthiophene) nanofibers

We present photovoltaic devices based on a blend of the conjugated polymer poly(3-hexylthiophene) (P3HT) with cadmium selenide nanorods, where the solvent for film deposition has been carefully chosen to optimize the film morphology. Using 1,2,4-trichlorobenzene (TCB), which has a high boiling point, as solvent for P3HT it is possible to obtain a fibrilar morphology, providing extended pathways for hole transport. Blend devices fabricated using this solvent gave solar power conversion efficiencies of 2.6%. This indicates that efficient transport of electrons and holes is achieved in these films, allowing them to operate effectively at solar illumination intensities.     

Macroscopic alignment of poly(3-hexylthiophene) for enhanced long-range collection of photogenerated carriers

An epitaxy-directing solvent additive 1,3,5-trichlorobenzene is combined with an off-center spin-casting technique to produce poly(3-hexylthiophene) (P3HT) fibers with uniaxial in-plane alignment on the centimeter scale. Photoconductive atomic force microscopy (pc-AFM) is used to characterize planar heterojunction devices assembled from phenyl-C₆₁ butyric acid methyl ester (PCBM) acceptor and both aligned and unaligned P3HT donor. By varying the relative positions of the laser spot (site of carrier generation) and probe (site of hole extraction), it is found that devices with aligned P3HT exhibit anisotropic and greatly enhanced long-range photocarrier transport, with nearly 10% of original photocurrent measured 400 µm from the laser spot along the direction parallel to the alignment. Complementary thin film transistor (TFT) measurements reveal a factor of ∼3.5 difference in the hole mobilities parallel and perpendicular to the direction of alignment. Together, these findings highlight the importance of macroscopic alignment as a strategy to overcome the low mobilities of disordered polymer semiconductors.1 © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 180–188     

Surface characterization and liquid crystal alignment behavior of comb-like poly(oxyethylene)/poly(3-hexylthiophene) blend films

The blend surfaces of poly[oxy(n-decylsulfonylmethyl)ethylene] (CH(3)-10SE) and poly (3-hexylthiophene) (P3HT) with different weight ratios were prepared by spin coating the polymer solution mixtures. In this study, their surface properties such as surface morphology, chemical composition, molecular structure, and wettability were systematically studied and correlated with liquid crystal (LC) alignment behaviors on the blend films. Therefore, we found that CH(3)-10SE part with a well-ordered side chain structure predominantly affects the both of wettability and LC alignment behavior of the blend films while there was no clear association between the wettability and the LC alignment behavior.