Role of a‐Si:H bulk in surface passivation of c‐Si wafers

The low thermal stability of hydrogenated amorphous silicon (a‐Si:H) thin films limits their widespread use for surface passivation of c‐Si wafers on the rear side of solar cells. We show that the thermal stability of a‐Si:H surface passivation is increased significantly by a hydrogen rich a‐Si:H bulk, which acts as a hydrogen reservoir for the a‐Si:H/c‐Si interface. Based on this mechanism, an excellent lifetime of 5.1 ms (at injection level of 10¹⁵ cm^–3) is achieved after annealing at 450 °C for 10 min. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Theoretical investigation on the passivation layer with linearly graded bandgap for the amorphous/crystalline silicon heterojunction solar cell

Passivation layer with linearly graded bandgap (LGB) was proposed to improve the performance of amorphous/crystalline silicon heterojunction (SHJ) solar cell by eliminating the large abrupt energy band uncontinuity at the a‐Si:H/c‐Si interface. Theoretical investigation on the a‐Si:H(p)/the LGB passivation layer(i)/c‐Si(n)/a‐Si:H(i)/a‐Si:H(n⁺) solar cell via AFORS‐HET simulation show that such LGB passivation layer could improve the solar cell efficiency (η) by enhancing the fill factor (FF) greatly, especially when the a‐Si:H(p) emitter was not efficiently doped and the passivation layer was relatively thick. But gap defects in the LGB passivation layer could make the improvement discounted due to the open‐circuit voltage (V_OC) decrease induced by recombination. To overcome this, it was quite effective to keep the gap defects away from the middle of the bandgap by widening the minimum bandgap of the LGB passivation layer to be a little larger than that of the c‐Si base. The underlying mechanisms were analysed in detail. How to achieve the LGB passivation layer experimentally was also discussed. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Silicone oxidation for a‐Si:H passivation of wafers bonded to glass

A possible scenario for wafer‐based silicon photovoltaics is the processing of solar modules starting from thin silicon wafers bonded to glass. However, interactions between the adhesive used for bonding and the solar cell processing can affect the surface passivation of the bonded wafer and decrease cell performances. A method that suppresses these interactions and leads to state‐of‐the‐art a‐Si:H surface passivation is presented in this Letter. The method is based on an increase of the surface cross‐linking of a silicone adhesive by means of an O₂ plasma and it is successfully tested on three different silicones. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Ion implantation into amorphous Si layers to form carrier‐selective contacts for Si solar cells

This paper reports our findings on the boron and phosphorus doping of very thin amorphous silicon layers by low energy ion implantation. These doped layers are implemented into a so‐called tunnel oxide passivated contact structure for Si solar cells. They act as carrier‐selective contacts and, thereby, lead to a significant reduction of the cell's recombination current. In this paper we address the influence of ion energy and ion dose in conjunction with the obligatory high‐temperature anneal needed for the realization of the passivation quality of the carrier‐selective contacts. The good results on the phosphorus‐doped (implied V_oc = 725 mV) and boron‐doped passivated contacts (iV_oc = 694 mV) open a promising route to a simplified interdigitated back contact (IBC) solar cell featuring passivated contacts. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Light trapping for a‐Si:H/µc‐Si:H tandem solar cells using direct pulsed laser interference texturing

We present a‐Si:H/µc‐Si:H tandem solar cells on laser textured ZnO:Al front contact layers. Direct pulsed laser interference patterning (DLIP) was used for writing arrays of one‐dimensional micro gratings of submicron period into ZnO:Al films. The laser texture provides good light trapping which is indicated by an increase in short‐circuit current density of 20% of the bottom cell limited device compared to cells on planar ZnO:Al. The open‐circuit voltage of the cells on laser textured ZnO:Al is almost the same as for cells on planar substrates, indicating excellent growth conditions for amorphous and microcrystalline silicon on the U‐shaped grating grooves. DLIP is a simple, single step and industrially applicable method for large area periodic texturing of ZnO:Al thin films. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Comparison of batch and in‐line PECVD of a‐Si:H passivation layers for silicon heterojunction solar cells

We present PECVD deposition of i‐a‐Si:H in an in‐line configuration for the fabrication of silicon heterojunction solar cells. For industry, in‐line processing has the potential to increase production throughput and yield. We compared batch and in‐line fabrication of i‐a‐Si:H passivation samples with identical plasma conditions and observed that the a‐Si:H material properties do not significantly differ. In batch‐type production the substrate is in the plasma zone at the moment of ignition, whereas for in‐line deposition the substrate is introduced into the plasma zone when steady plasma conditions have been reached. Our preliminary results show that there are depositions conditions that result both for in‐line and batch‐type deposition in good i‐a‐Si:H passivation layers. Therefore both methods can equally well be considered for the production of silicon heterojunction solar cells. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

19.4%‐efficient large‐area fully screen‐printed silicon solar cells

We demonstrate industrially feasible large‐area solar cells with passivated homogeneous emitter and rear achieving energy conversion efficiencies of up to 19.4% on 125 × 125 mm² p‐type 2–3 Ω cm boron‐doped Czochralski silicon wafers. Front and rear metal contacts are fabricated by screen‐printing of silver and aluminum paste and firing in a conventional belt furnace. We implement two different dielectric rear surface passivation stacks: (i) a thermally grown silicon dioxide/silicon nitride stack and (ii) an atomic‐layer‐deposited aluminum oxide/silicon nitride stack. The dielectrics at the rear result in a decreased surface recombination velocity of S_rear = 70 cm/s and 80 cm/s, and an increased internal IR reflectance of up to 91% corresponding to an improved J_sc of up to 38.9 mA/cm² and V_oc of up to 664 mV. We observe an increase in cell efficiency of 0.8% absolute for the cells compared to 18.6% efficient reference solar cells featuring a full‐area aluminum back surface field. To our knowledge, the energy conversion efficiency of 19.4% is the best value reported so far for large area screen‐printed solar cells. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Small‐signal lock‐in thermography at the maximum power point of an a‐Si solar mini‐module

The paper introduces a small‐signal lock‐in thermography (MPP‐SLIT) technique based on voltage modulations around the maximum power point (MPP) of an illuminated solar cell or module. At MPP the differential power dissipation of the entire device turns from negative (less dissipation with increasing voltage) to positive (more dissipation with increasing voltage). Pictures taken around the MPP unveil a positive or negative response depending on the respective local maximum power point. This paper presents qualitative discussions for two situations; firstly, where opposite signs of the LIT signal arise due to the parallel connection of areas with different photovoltaic quality on a single cell, and second, the interaction of cells of different quality connected in series in a solar module. The experimental verification of our method is obtained from an amorphous silicon thin‐film mini‐module. The experimental results demonstrate the validity of the method, especially the fact that positive and negative signs are observed in the same picture and depend on the position of the local operating point with respect to the local MPP. It is also observed that the signal arising from power dissipation at the cell interconnects is always negative. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Low‐temperature atomic layer deposition of MoOx for silicon heterojunction solar cells

The preparation of high‐quality molybdenum oxide (MoO_x) is demonstrated by plasma‐enhanced atomic layer deposition (ALD) at substrate temperatures down to 50 °C. The films are amorphous, slightly substoichiometric with respect to MoO₃, and free of other elements apart from hydrogen (&11 at%). The films have a high transparency in the visible region and their compatibility with a‐Si:H passivation schemes is demonstrated. It is discussed that these aspects, in conjunction with the low processing temperature and the ability to deposit very thin conformal films, make this ALD process promising for the future application of MoO_x in hole‐selective contacts for silicon heterojunction solar cells. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Ca/Alq3 hybrid cathode buffer layer for the optimization of organic solar cells based on a planar heterojunction

Use of efficient anode cathode buffer layer (CBL) is crucial to improve the efficiency of organic photovoltaic cells. Here we show that using a double CBL, Ca/Alq₃, allows improving significantly cell performances. The insertion of Ca layer facilitates electron harvesting and blocks hole collection, leading to improved charge selectivity and reduced leakage current, whereas Alq₃ blocks excitons. After optimisation of this Ca/Alq₃ CBL using CuPc as electron donor, it is shown that it is also efficient when SubPc is substituted to CuPc in the cells. In that case we show that the morphology of the SubPc layer, and therefore the efficiency of the cells, strongly depends on the deposition rate of the SubPc film. It is necessary to deposit slowly (0.02 nm/s) the SubPc films because at higher deposition rate (0.06 nm/s) the films are porous, which induces leakage currents and deterioration of the cell performances. The SubPc layers whose formations are kinetically driven at low deposition rates are more uniform, whereas those deposited faster exhibit high densities of pinholes.     

Enhanced rear‐side reflection and firing‐stable surface passivation of silicon solar cells with capping polymer films

Low refractive index polymer materials have been investigated with a view to form the back surface mirror of advanced silicon solar cells. SiO_x:H or AlO_y SiO_x:H polymer films were spun on top of an ultra‐thin (<10 nm) atomic‐layer‐deposited (ALD) Al₂O₃ layer, itself deposited on low‐resistivity (1 Ω cm) p‐type crystalline silicon wafers. These double‐layer stacks were compared to both ALD Al₂O₃ single layers and ALD Al₂O₃/plasma‐enhanced chemical vapour deposited (PECVD) SiN_x stacks, in terms of surface passivation, firing stability and rear‐side reflection. Very low surface recombination velocity (SRV) values approaching 3 cm/s were achieved with ALD Al₂O₃ layers in the 4–8 nm range. Whilst the surface passivation of the single ALD Al₂O₃ layer is maintained after a standard firing step typical of screen printing metallisation, a harsher firing regime revealed an enhanced thermal stability of the ALD Al₂O₃/SiO_x:H and ALD Al₂O₃/AlO_y SiO_x:H stacks. Using simple two‐dimensional optical modelling of rear‐side reflection it is shown that the low refractive index exhibited by SiO_x:H and AlO_y SiO_x:H results in superior optical performance as compared to PECVD SiN_x, with gains in photogenerated current of ～0.125 mA/cm² at a capping thickness of 100 nm. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Assessment of the illumination dependency of Al2O3 and SiO2 rear‐passivated p‐type silicon solar cells

This Letter discusses an important difference between positively charged SiO₂ and negatively charged Al₂O₃ rear‐passivated p‐type Si solar cells: their illumination level dependency. For positively charged SiO₂ rear‐passivated p‐type Si solar cells, a loss in short circuit current (J_SC) and open circuit voltage (V_OC) as a function of illumination level is mainly caused by parasitic shunting and a decrease in surface recombination, respectively. Hence, the relative loss in cell conversion efficiency, J_SC, and V_OC as a function of the illumination level for SiO₂ compared to Al₂O₃ rear‐passivated p‐type Si solar cells has been measured and discussed. Subsequently, an exponential decay fit of the loss in cell efficiency is applied in order to estimate the difference in the energy output for both cell types in three different territories: Belgium (EU), Seattle and Austin (US). The observed trends in the difference in energy output between both cells, as a function of time of the year and region, are as expected and discussed. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Micromorph tandem solar cells: optimization of the microcrystalline silicon bottom cell in a single chamber system

We report on the development of single chamber deposition of microcrystalline and micromorph tandem solar cells directly onto low-cost glass substrates. The cells have pin single-junction or pin/pin double-junction structures on glass substrates coated with a transparent conductive oxide layer such as SnO₂ or ZnO. By controlling boron and phosphorus contaminations, a single-junction microcrystalline silicon cell with a conversion efficiency of 7.47% is achieved with an i-layer thickness of 1.2 μm. In tandem devices, by thickness optimization of the microcrystalline silicon bottom solar cell, we obtained an initial conversion efficiency of 9.91% with an aluminum (Al) back reflector without a dielectric layer. In order to enhance the performance of the tandem solar cells, an improved light trapping structure with a ZnO/Al back reflector is used. As a result, a tandem solar cell with 11.04% of initial conversion efficiency has been obtained.     

Improved control of the phosphorous surface concentration during in‐line diffusion of c‐Si solar cells by APCVD

Emitter formation for industrial crystalline silicon (c‐Si) solar cells is demonstrated by the deposition of phosphorous‐doped silicate glasses (PSG) on p‐type monocrystalline silicon wafers via in‐line atmospheric pressure chemical vapor deposition (APCVD) and subsequent thermal diffusion. Processed wafers with and without the PSG layers have been analysed by SIMS measurements to investigate the depth profiles of the resultant phosphorous emitters. Subsequently, complete solar cells were fabricated using the phosphorous emitters formed by doped silicate glasses to determine the impact of this high‐throughput doping method on cell performance. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

钙钛矿/硅叠层太阳电池中平面a-Si:H/c-Si异质结底电池的钝化优化及性能提高

最近,旋涂法制备的钙钛矿/平面硅异质结高效叠层太阳电池引起人们广泛关注,主要原因是相比于绒面硅衬底制备的钙钛矿/硅叠层太阳电池,其制备工艺简单、制备成本低且效率高.对于平面a-Si:H/c-Si异质结电池, a-Si:H/c-Si界面的良好钝化是获得高转换效率的关键,进而决定了钙钛矿/硅异质结叠层太阳电池的性能.本文主要从硅片表面处理、a-Si:H钝化层和P型发射极等方面展开研究,通过对硅片表面的氢氟酸(HF)浸泡时间和氢等离子体预处理气体流量、a-Si:H钝化层沉积参数、钝化层与P型发射极(I/P)界面富氢等离子体处理的综合调控,获得了相应的优化工艺参数.对比研究了p-a-Si:H和p-nc-Si:H两种缓冲层材料对I/P界面的影响,其中高电导、宽带隙的p-nc-Si:H缓冲层既能够降低I/P界面的缺陷态,又可以增强P型发射层的暗电导率,提高了前表面场效应钝化效果.通过上述优化,制备出最佳的P-type emitter layer/aSi:H(i)/c-Si/a-Si:H(i)/N-type layer (inip)结构样品的少子寿命与implied-Voc分别达到2855μs和709 mV,表现出良好的钝化效果.应用于平面a-Si:H/c-Si异质结太阳电池,转换效率达到18.76%,其中开路电压达到681.5 mV,相对于未优化的电池提升了34.3 mV.将上述平面a-Si:H/c-Si异质结太阳电池作为底电池,对应的钙钛矿/硅异质结叠层太阳电池的开路电压达到1780 mV,转换效率达到21.24%,证明了上述工艺优化能够有效地改善叠层太阳电池中的硅异质结底电池的钝化及电池性能.     

Contact passivation in silicon solar cells using atomic‐layer‐deposited aluminum oxide layers

Atomic‐layer‐deposited aluminum oxide (AlO_x) layers are implemented between the phosphorous‐diffused n⁺‐emitter and the Al contact of passivated emitter and rear silicon solar cells. The increase in open‐circuit voltage V_oc of 12 mV for solar cells with the Al/AlO_x/n⁺‐Si tunnel contact compared to contacts without AlO_x layer indicates contact passivation by the implemented AlO_x. For the optimal AlO_x layer thickness of 0.24 nm we achieve an independently confirmed energy conversion efficiency of 21.7% and a V_oc of 673 mV. For AlO_x thicknesses larger than 0.24 nm the tunnel probability decreases, resulting in a larger series resistance. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Surface passivation of phosphorus‐diffused n+‐type emitters by plasma‐assisted atomic‐layer deposited Al2O3

In recent years Al₂O₃ has received tremendous interest in the photovoltaic community for the application as surface passivation layer for crystalline silicon. Especially p‐type c‐Si surfaces are very effectively passivated by Al₂O₃, including p‐type emitters, due to the high fixed negative charge in the Al₂O₃ film. In this Letter we show that Al₂O₃ prepared by plasma‐assisted atomic layer deposition (ALD) can actually provide a good level of surface passivation for highly doped n‐type emitters in the range of 10–100 Ω/sq with implied‐V_oc values up to 680 mV. For n‐type emitters in the range of 100–200 Ω/sq the implied‐V_oc drops to a value of 600 mV for a 200 Ω/sq emitter, indicating a decreased level of surface passivation. For even lighter doped n‐type surfaces the passivation quality increases again to implied‐V_oc values well above 700 mV. Hence, the results presented here indicate that within a certain doping range, highly doped n‐ and p‐type surfaces can be passivated simultaneously by Al₂O₃. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Extremely low surface recombination in 1 Ω cm n‐type monocrystalline silicon

A key requirement in the recent development of highly efficient silicon solar cells is the outstanding passivation of their surfaces. In this work, plasma enhanced chemical vapour deposition of a triple layer dielectric consisting of amorphous silicon, silicon oxide and silicon nitride, charged extrinsically using corona, has been used to demonstrate extremely low surface recombination. Assuming Richter's parametrisation for bulk lifetime, an effective surface recombination velocity S_eff = 0.1 cm/s at Δn = 10¹⁵ cm^–3 has been obtained for planar, float zone, n ‐type, 1 Ω cm silicon. This equates to a saturation current density J_0s = 0.3 fA/cm², and a 1‐sun implied open‐circuit voltage of 738 mV. These surface recombination parameters are among the lowest reported for 1 Ω cm c‐Si. A combination of impedance spectroscopy and corona‐lifetime measurements shows that the outstanding chemical passivation is due to the small hole capture cross section for states at the interface between the Si and a‐Si layer which are hydrogenated during nitride deposition. (© 2016 The Authors. Phys. Status Solidi RRL published by WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Quantitative evaluation method for electroluminescence images of a‐Si:H thin‐film solar modules

This work presents a method for extracting the absolute local junction voltage of a‐Si:H thin‐film solar cells and modules from electroluminescence (EL) images. It is shown that the electroluminescent emission of a‐Si:H devices follows a diode law with a radiative ideality factor n_r larger than one. We introduce an evaluation method that allows us to determine the absolute local junction voltage in cases of n_r > 1, while existing approaches rely on the assumption of n_r = 1. Furthermore, we find that the experimentally determined values of n_r vary from sample to sample. It is also explained why the derived radiative ideality factor is influenced by the spectral sensitivity of the camera system used in the experiment. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)