Vibration-insensitive fiber spool for laser stabilization

Excess frequency noise induced by mechanical vibration is the dominant noise source at low Fourier frequencies in fiber-delay-line stabilized lasers. To resolve this problem, a double-winding fiber spool is designed and implemented that has ultralow acceleration sensitivity in all spatial directions. By carefully choosing the optimal geometry parameters of the fiber spool, we achieve acceleration sensitivity of 8 × 10~(-11)/g and 3 × 10~(-11)/g(g denotes the gravitational acceleration) in axial and radial directions, respectively.     

基于超窄线宽激光的一氧化碳多参数检测研究

基于超窄线宽激光特性和激光器波长扫描技术,通过对一氧化碳气体近红外吸收光谱的测量及分析,设计了一氧化碳气体多参数实时在线检测系统.系统采用超窄线宽可调谐半导体激光器作为光源,利用气体直接吸收光谱测温法,实现了一氧化碳气体温度实时检测.根据所测温度值并结合气体浓度差分检测原理,实现了一氧化碳气体温度和浓度同时测量.利用超...     

Simple and compact 1-Hz laser system via an improved mounting configuration of a reference cavity

We report an improved mounting configuration for a passive optical cavity used for laser frequency stabilization. The associated reduction of the vibration sensitivity of the effective cavity length has led to a simple and compact reference cavity system for laser stabilization at the level of 1 Hz linewidth.     

Low gain laser with an unstable cavity

A neon 633 nm laser with an unstable cavity was made to lase in the negative unstable region. The characteristic parameters were measured. The loss calculated by using both the geometric approach and the diffraction integral is higher than the gain of the gas mixture, it contradicts the experimental results. If the radial dependence of the gain is taken into account then the calculated loss fits the experimental results satisfactorily.     

RF cavity for gas laser excitation

Summary A new technique for RF transverse excitation of gas laser has been tested: the plasma tube has been put inside a quarter wave strip line RF cavity. Excellent field uniformity and arcing problem avoidance have been observed. The efficiency is greater than 15%. The guidelines for cavity design are discussed. Work partially supported by ENEA-Contract No. C/451 (Dip. Fusione Associazione EURATOM-ENEA, CRE Frascati).     

Mode-locked pulse generation from an all-FMF ring laser cavity

Experimental generation of stable mode-locked pulses and cylindrical vector beams(CVBs), from an all fewmode fiber(FMF) ring laser is first reported, to the best of our knowledge. In this laser, a section of few-mode erbium-doped fiber(FM-EDF) is used as the gain medium. The FM-EDF is pumped by 976 nm laser with LP11 mode, which is simultaneously converted and multiplexed through a homemade hybrid device, i.e., wavelength division multiplexing-mode selection coupler(WDM-MSC). All the components in our experiment are connected using FMF. The resulted CVB pulses have a spectral width of 0.33 nm with a repetition rate of 30.58 MHz under the pump power of 340 m W. Moreover, both azimuthally and radially polarized CVBs were achieved with a high purity of 95%. This mode-locked CVB fiber laser with an all FMF configuration opens the way to manipulate the transverse mode in mode-locked fiber lasers.     

带非谐振环激光谐振腔的特性

本文中分析了带非谐振环激光谐振腔的光学对称性、稳定性和光束腰位置,可以据此选择谐振腔参数。     

Tunable dual-wavelength operation of an external cavity semiconductor laser

Tunable dual-wavelength operation of a laser diode has been achieved using a dual-period holographic element. The holographic element was positioned in Littrow configuration in an external cavity. The design of this holographic element was based on the superposition of a constant-period grating and a variable-period grating on the same location in a photoresist. We observed simultaneous emission at two wavelengths from a visible semiconductor laser operated with this holographic element. The spectral separation of the dual-wavelength output was varied from 0.76 to 6.27 nm by a simple translation of the holographic element.     

Extended temperature tuning of an external cavity diode laser

We describe the construction and operation of an external cavity diode laser in which the diode is cooled to -45 °C. This technique allows us to pull the wavelength of a nominally 782 nm diode to operate at 766.7 nm, a change of over 15 nm. The important aspects of our design are its ease and low cost as compared to other designs of changing the operating wavelength of laser diodes. We provide background information on thermal design with multiple TECs so the reader can extend this example for use in their own applications. PACS 42.60.By; 42.62.Fi; 32.80.Pj     

Sub-Doppler spectroscopy with an external cavity quantum cascade laser

The linewidth of an external cavity quantum cascade laser is studied as a function of injection current and laser scan rate. The laser linewidth is inferred to be ca. 2.5 MHz from Lamb-dip spectra on a low pressure sample of NO and its variation with injection current is well modeled using literature values for the intrinsic material properties of the lasing medium. The laser linewidth measurements are corroborated by polarization spectroscopy studies as well as by analysis of hyperfine structure and cross-over resonances.     

Continuous-wave wavelength conversion for high-power applications using an external cavity diamond Raman laser

We demonstrate continuous-wave (cw) operation of a diamond Raman laser at 1240 nm in an external cavity configuration. The output power increased linearly with pump power with a 49.7% slope efficiency and reached 10.1 W at the maximum available pump power of 31 W. The combination of resonator design with diamond provides a novel approach to power-scalable cw wavelength and beam conversion.     

Quasi-monolithic ring resonator for efficient frequency doubling of an external cavity diode laser

A quasi-monolithic second-harmonic-generation ring resonator assembled with miniaturized components is presented. The ring contains a 10-mm-long bulk periodically poled lithium niobate crystal for second-harmonic generation, four plane mirrors and two gradient-index lenses. All parts are mounted on a glass substrate with an overall size of 19.5 mm×8.5 mm×4 mm. As pump source a broad-area laser diode operated in an external resonator with Littrow arrangement is utilized. This external cavity diode laser provides near diffraction limited, narrow-bandwidth emission with an optical output power of 450 mW at a wavelength of 976 nm. Locking of the diode laser emission to the resonance frequency of the ring cavity was achieved by an optical self-injection locking technique. With this setup more than 126 mW of diffraction-limited blue light at 488 nm could be generated. The opto–optical conversion efficiency was 28% and a wall plug efficiency better than 5.5% could be achieved.     

半内腔He-Ne激光器的调整技巧

介绍了半内腔式He-Ne激光器的结构及调整的技巧,测量了在不同放电电流以及不同腔长条件下激光器的输出功率,得到了最佳的放电电流. 半内腔式He-Ne激光器的应用,有助于学生了解激光器的工作物质、谐振腔等主要组成部分,也促进了学生对激光理论的进一步理解.     

Pulsed laser cooling for cavity optomechanical resonators

A pulsed cooling scheme for optomechanical systems is presented that is capable of cooling at much faster rates, shorter overall cooling times, and for a wider set of experimental scenarios than is possible by conventional methods. The proposed scheme can be implemented for both strongly and weakly coupled optomechanical systems in both weakly and highly dissipative cavities. We study analytically its underlying working mechanism, which is based on interferometric control of optomechanical interactions, and we demonstrate its efficiency with pulse sequences that are obtained by using methods from optimal control. The short time in which our scheme approaches the optomechanical ground state allows for a significant relaxation of current experimental constraints. Finally, the framework presented here can be used to create a rich variety of optomechanical interactions and hence offers a novel, readily available toolbox for fast optomechanical quantum control.     

一种实现光纤激光器高功率输出的方法

介绍了一种实现光纤激光器高功率输出的新方法——采用螺旋芯光纤，这种光纤是在光纤制作过程中按照一定的弯曲半径使纤芯呈螺旋状排布在光纤包层中。介绍了这种螺旋芯光纤的原理和其提高输出功率的能力，以及目前的理论与实验研究现状。基于该光纤，提出了一种光纤激光器相干合成新思想。     

Intracavity photoacoustic gas detection with an external cavity diode laser

The first use of an external cavity diode-laser light source in combination with a photoacoustic detector for high-sensitivity gas detection is described. This combined system is applicable for detecting gases with absorption coefficients as low as 5 x 10^–8 cm^–1 by operating the photoacoustic cell in an intracavity mode. Measurements were made on the 1.13 m absorption lines of water vapour. For quantitative measurements, it was found to be necessary to introduce a reference cell into the system.     

Power efficiency of a semiconductor laser with an external cavity

Optical feedback modifies the power vs. current diagram of a laser diode as well as its spectrum. Though optimization of the spectral characteristics is usually the main goal in the design of an external cavity source, power efficiency is also important, especially with relatively high power devices, where temperature variations due to dissipation can have an impact on the wavelength stability and on the laser lifetime. A useful parameter to describe the total power efficiency of the stabilized laser, relative to that of the solitary laser, is proposed in this paper. The dependence of this parameter on the characteristics of the active device, and of the external cavity, is investigated.