Preparation of Ca<Subscript>3</Subscript>Co<Subscript>4</Subscript>O<Subscript>9</Subscript> by polyacrylamide gel processing and its thermoelectric properties

Ca₃Co₄O₉ powder was prepared by a polyacrylamide gel route in this paper. The effect of the processing on microstructure and thermoelectric properties of Ca₃Co₄O₉ ceramics via spark plasma sintering were investigated. Electrical measurement shows that the Seebeck coefficient and conductivity are 170 μV/K and 128 S/cm, respectively, at 700 °C, yielding a power factor value of 3.70 × 10⁻⁴ W m⁻¹ K⁻² at 700 °C, which is larger than that of Ca₃Co₄O₉ ceramics via solid-state reaction processing. The polyacrylamide gel processing is a fast, cheap, reproducible and easily scaled up chemical route to improve the thermoelectric properties of Ca₃Co₄O₉ ceramics by preparing the homogeneous and pure Ca₃Co₄O₉ phase.     

Influence of composition on corroding process of Na<Subscript>2</Subscript>O-K<Subscript>2</Subscript>O-CaO-ZrO<Subscript>2</Subscript>-SiO<Subscript>2</Subscript> glasses

The corroding process of six glasses of the Na₂O-K₂O-CaO-ZrO₂-SiO₂ system with ZrO₂content 0–2.13 mass % by water was observed during static tests at 121°C and pressure of 0.25 MPa in steam sterilizer. Significant increase of Na⁺ and K⁺ content in leachates was observed after the addition of ZrO₂ into glass. Further increase of the content of ZrO₂ in glasses slowed down the rate of Na⁺ and K⁺ leaching. The leaching process of SiO₂ as well as Na⁺, K⁺, and Ca²⁺ ions was evaluated on the basis of comparison with model leaching processes. Variation of the concentrations of Na⁺, K⁺, Ca²⁺, and SiO₂ in leachates with time was described by empirical equation. Observed changes in the initial leaching rates of Na⁺, K⁺, Ca²⁺, and SiO₂ can be ascribed to the content of ZrO₂ in glasses. The presence of ZrO₂ in glasses reduced the overall rate of glass dissolution.     

Voltammetric determination of the trace amounts of bromate in drinking water after pre-concentration on hydrous γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

A differential pulse voltammetric (DPV) method for the determination of bromate in drinking water, after pre-concentration on γ-Al₂O₃, is proposed. The reduction peak of bromate has been observed at the potential E _p -−1.6 V in an ammonia buffer as a supporting electrolyte. The method has been successfully applied to determine a bromate concentration of 2.5 μg·l⁻¹ in drinking water (RSD=6.1%, n=7). A sample pre-treatment with a column filled with mixed cation-exchange resin in Ag, Ba and H forms was needed before pre-concentration of bromate on alumina.     

Synthesis of ammonia from natural gas at atmospheric pressure with doped ceria–Ca<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>–K<Subscript>3</Subscript>PO<Subscript>4</Subscript> composite electrolyte and its proton conductivity at intermediate temperature

A new type of oxide–salt composite electrolyte, yttrium doped ceria YDC–Ca₃(PO₄)₂–K₃PO₄, was developed and demonstrated for its promising use for ammonia synthesis. Using this composite electrolyte, ammonia was synthesized from nitrogen and natural gas at atmospheric pressure in the solid-state proton conducting cell reactor, and the optimal condition for ammonia production was determined . The evolved rate of ammonia is up to 6.95×10⁻⁹ mol s⁻¹ cm⁻².     

Determination of the enthalpy of fusion of K<Subscript>3</Subscript>TaO<Subscript>2</Subscript>F<Subscript>4</Subscript> and KTaF<Subscript>6</Subscript>

Areas of fusion and crystallization peaks of K₃TaO₂F₄ and KTaF₆ were measured using the DSC mode of a high-temperature calorimeter (SETARAM 1800 K). On the basis of these quantities, considering the temperature dependence of the calorimeter sensitivity, values of the fusion enthalpy of K₃TaO₂F₄ at the fusion temperature of 1181 K of (43 ± 4) kJ mol⁻¹ and of KTaF₆ at the fusion temperature of 760 K of (8 ± 1) kJ mol⁻¹ were determined.     

A kinetic study of the oxidation of <Emphasis Type="SmallCaps">l</Emphasis>-methionine by water soluble colloidal MnO<Subscript>2</Subscript>

Aqueous solution of water soluble colloidal MnO₂ was prepared by Perez-Benito method. Kinetics of l-methionine oxidation by colloidal MnO₂ in perchloric acid (0.93 × 10⁻⁴ to 3.72 × 10⁻⁴ mol dm⁻³) has been studied spectrophotometrically. The reaction follows first-order kinetics with respect to [H⁺]. The first-order kinetics with respect to l-methionine at low concentration shifts to zero order at higher concentration. The effects of [Mn(II)] and [F⁻] on the reaction rate were also determined. Manganese (II) has sigmoidal effect on the rate reaction and act as auto catalyst. The exact dependence on [Mn(II)] cannot be explained due to its oxidation by colloidal MnO₂. Methionine sulfoxide was formed as the oxidation product of l-methionine. Ammonia and carbon dioxide have not been identified as the reaction products. The mechanism with the observed kinetics has been proposed and discussed.     

Osmotic Coefficients of the Li<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript>+LiCl + H<Subscript>2</Subscript>O System at <Emphasis Type="Italic">T</Emphasis>=273.15 K

Osmotic coefficients and water activities for the Li₂B₄O₇+LiCl+H₂O system have been measured at T=273.15 K by the isopiestic method, using an improved apparatus. Two types of osmotic coefficients, φ _S and φ _E, were determined. φ _S is based on the stoichiometric molalities of the solute Li₂B₄O₇(aq), and φ _E is based on equilibrium molalities from consideration of the equilibrium speciation into H₃BO₃,B(OH)₄⁻ and B₃O₃(OH)₄⁻. The stoichiometric equilibrium constants K _m for the aqueous speciation reactions were estimated. Two types of representations of the osmotic coefficients for the Li₂B₄O₇+LiCl+H₂O system are presented with ion-interaction models based on Pitzer’s equations with minor modifications: model (I) represents the φ _S data with six parameters based on considering the ion-interactions between three ionic species of Li⁺, Cl⁻, and B₄O₇²⁻, and model (II) for represents the φ _E data based on considering the equilibrium speciation. The parameters of models (I) and (II) are presented. The standard deviations for the two models are 0.0152 and 0.0298, respectively. Model (I) was more satisfactory than model (II) for representing the isopiestic data.     

Electropolymerization of <Emphasis Type="Italic">trans</Emphasis>-[RuCl<Subscript>2</Subscript>(vpy)<Subscript>4</Subscript>] complex—EQCM and Raman studies

The electropolymerization of trans-[RuCl₂(vpy)₄] (vpy=4-vinylpyridine) on Au or Pt electrodes was studied by cyclic voltammetry, electrochemical quartz crystal microbalance (EQCM) technique, and Raman spectroscopy. Cyclic voltammetry of the monomer at a microelectrode shows the typical Ru(III/II) and Ru(IV/III) waves, together with the vinyl reduction waves at −1.5 and −2.45 V and adsorption wave at −0.8 V. Electrodeposition on EQCM technique performed under potential cycling between −0.9 and −2.0 V revealed that the polymerization proceeded well in advance of the vinyl reduction waves. At potentials more positive than −0.9 V, soluble oligomers were deposited irreversibly on the electrode during the oxidative sweep. The film also showed reversible mass changes due to the oxidation and accompanying ingress of charge-balancing anions and solvent into the film. In contrast, potentiostatic growth of the polymer at −1.6 V was slower because the oligomeric material was lost completely from the electrode. Unreacted vinyl groups were detected by in situ Raman spectroscopy for films grown at −0.7, −0.9, and −1.6 V but were absent when the polymerization was carried out at −2.9 V vs Ag/Ag⁺.     

Synthesis and electrochemical properties of Ca-doped LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2</Subscript>O<Subscript>2</Subscript> cathode material for lithium ion battery

LiNi_0.8Co_0.2O₂ and Ca-doped LiNi_0.8Co_0.2O₂ cathode materials have been synthesized via a rheological phase reaction method. X-ray diffraction studies show that the Ca-doped material, and also the discharged electrode, maintains a hexagonal structure even when cycled in the range of 3.0–4.35 V (vs Li⁺/Li) after 100 cycles. Electrochemical tests show that Ca doping significantly improves the reversible capacity and cyclability. The improvement is attributed to the formation of defects caused by the partial occupancy of Ca²⁺ ions in lithium lattice sites, which reduce the resistance and thus improve the electrochemical properties.     

A novel amperometric immunosensor based on Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> magnetic nanoparticles/chitosan composite film for determination of ferritin

A novel amperometric immunosensor was developed by immobilizing ferritin antibody (FeAb) on the surface of Fe₃O₄ magnetic nanoparticles/chitosan composite film modified glassy carbon electrode (GCE). This material combined the advantages of inorganic Fe₃O₄ nanoparticles with the organic polymer chitosan. The stepwise assembly procedure of the immunosensor was characterized by means of differential pulse voltammetry (DPV) and ac impedance. The K₃Fe(CN)₆/K₄Fe(CN)₆ was used as a marker to probe the interface and to determinate ferritin. The factors that could influence the performance of the resulting immunosensor were studied in detail. After the immunosensor was incubated with ferritin for 32 min at 35 °C, the DPV current decreased linearly with the logarithm of ferritin concentration in the range from 20 to 500 ng mL⁻¹ with a correlation coefficient of 0.995 and a detection limit of 7.0 ng mL⁻¹. This immunosensor was used to analyze ferritin in human serum samples. The analytical results showed that the developed immunoassay was comparable with the radioimmunoassay (RIA), and the studied immunosensor exhibited good accuracy, high sensitivity, and long-term stability for 3 weeks, which implies a promising alternative approach for detecting ferritin in clinical diagnosis.     

Electronic structure and chemical bonding in K<Subscript>2</Subscript>V<Subscript>3</Subscript>O<Subscript>8</Subscript>

The calculations of the electronic structure of layered polyvanadate K₂V₃O₈ were made employing the spin-polarized tight-binding LMTO method. Calculated magnetic moment for K₄V₆O₁₆ compound phase equals 1.97 μ_B. V-O interactions were established to be dominating in the chemical bonding generation in this polyvanadate according to the estimated crystal orbital overlap population. The covalent bonds V(2)-V(2) in V(2)₂O₇ groups and electron density localization on vanadium atoms in isolated pyramids V(1)O₅ were found.     

Determination of the enthalpy of fusion of Na<Subscript>3</Subscript>FeF<Subscript>6</Subscript>

The areas of the fusion and crystallization peaks of Na₃FeF₆ and of four calibration substances (KCl, NaCl, Na₂SO₄, and K₂SO₄) were measured using the DSC mode of a high-temperature calorimeter. Using the measured quantities and known values of the enthalpy of fusion of the calibration substances, the enthalpy of fusion of Na₃FeF₆ was determined. Its value at the temperature of fusion 1224 K was 70 ± 4 kJ mol⁻¹.     

Effects of particle size on the electrochemical performances of a layered double hydroxide, [Ni<Subscript>4</Subscript>Al(OH)<Subscript>10</Subscript>]NO<Subscript>3</Subscript>

In this paper, the electrochemical performances of a layered double hydroxide, [Ni₄Al(OH)₁₀]NO₃, of different particle sizes are studied. The results show that the particle size of the sample has evident effects on its discharge capacity at high current density, although a larger capacity may be observed for the bigger particles when they are discharged at lower current densities, e.g. 0.2 A g⁻¹. However, the capacity decreases more quickly than that of the sample in smaller particle size when the current density increases. For example, the discharge capacity of the smallest particle remains as high as 180 mAh·g⁻¹ even at very high current density, e.g. 4.0 A g⁻¹. The results also show that long time soaked electrodes in 7 mol l⁻¹ KOH have improved performance, especially for the hydrothermal samples. It also seems that there is an optimal size for materials, which can maintain their performance for longer time.     

Electrochemical study of Meldola's blue,methylene blue and toluidine blue immobilized on a SiO<Subscript>2</Subscript>/Sb<Subscript>2</Subscript>O3 binary oxide matrix obtained by the sol-gel processing method

SiO₂/Sb₂O₃ (SiSb), having a specific surface area, S _BET, of 788 m² g⁻¹, an average pore diameter of 1.9 nm and 4.7 wt% of Sb, was prepared by the sol-gel processing method. Meldola's blue (MeB), methylene blue (MB) and toluidine blue (TB) were immobilized on SiSb by an ion exchange reaction. The amounts of the dyes bonded to the substrate surface were 12.49, 14.26 and 22.78 μmol g⁻¹ for MeB, MB and TB, respectively. These materials were used to modify carbon paste electrodes. The midpoint potentials (E _m) of the immobilized dyes were −0.059, −0.17 and −0.18 V vs. SCE for SiSb/MeB, SiSb/MB and SiSb/TB modified carbon paste electrodes, respectively. A solution pH between 3 and 7 practically did not affect the midpoint potential of the immobilized dyes. The electrodes presented reproducible responses and were chemically stable under various oxidation-reduction cycles. Among the immobilized dyes, MeB was the most efficient to mediate the electron transfer for NADH oxidation in aqueous solution at pH 7. In this case, amperometric detection of NADH at an applied potential of 0 mV vs. SCE gives linear responses over the concentration range of 0.1–0.6 mmol L⁻¹, with a detection limit of 7 μmol L⁻¹.     

Preparation and characterization of LiFePO<Subscript>4</Subscript> from NH<Subscript>4</Subscript>FePO<Subscript>4</Subscript>·H<Subscript>2</Subscript>O under different microwave heating conditions

Olivine-type LiFePO₄ is a very promising polyanion-type cathode material for lithium-ion batteries. In this work, LiFePO₄ with high specificity capacity is obtained from a novel precursor NH₄FePO₄·H₂O via microwave processing. The grains grow up in the duration of sintering until they reach the decomposition temperature. The apparent conductivity of the samples rises rapidly with the irradiation time and influences the electrochemical performance of the material greatly at high current density. As a result, the LiFePO₄ cathode material obtained with a sintering time of 15 min has good electrochemical performance. Between 2.5 and 4.2 V versus Li, a reversible capacity is as high as 156 mAh g⁻¹ at 0.05 C.     

Heat capacity at constant pressure and thermodynamic properties of phase transitions in PbMO<Subscript>3</Subscript> (<Emphasis Type="Italic">M</Emphasis>=Ti,Zr and Hf)

The heat capacity of PbMO₃ (M=Ti, Zr and Hf) at constant pressure was measured using a differential scanning calorimeter (DSC) from room temperature up to 870 K. Large anomalies were found in the heat capacity curves, corresponding to the ferroelectricparaelectric phase transition in PbTiO₃ (PT), the antiferroelectric-paraelectric phase transitions in PbZrO₃ (PZ) and PbHfO₃ (PH). The transition entropies were estimated as 7.3 J K⁻¹ mol⁻¹ (PT), 9.9 J K⁻¹ mol⁻¹ (PZ) and 9.3 J K⁻¹ mol⁻¹ (PH). These values of transition entropies are much larger than that of a typical displacive-type phase transition.     

Theoretical study of the mechanism for C-H bond activation in spin-forbidden reaction between Ti<Superscript>+</Superscript> and C<Subscript>2</Subscript>H<Subscript>4</Subscript>

The mechanism of the spin-forbidden reaction Ti⁺(⁴F, 3d²4s¹) + C₂H₄→TiC₂H₂ ⁺ (²A₂) + H₂ on both doublet and quartet potential energy surfaces has been investigated at the B3LYP level of theory. Crossing points between the potential energy surfaces and the possible spin inversion process are discussed by means of spin-orbit coupling (SOC) calculations. The strength of the SOC between the low-lying quartet state and the doublet state is 59.3 cm⁻¹ in the intermediate complex IM1-⁴B₂. Thus, the changes of its spin multiplicity may occur from the quartet to the doublet surface to form IM1-²A₁, leading to a sig-nificant decrease in the barrier height on the quartet PES. After the insertion intermediate IM2, two distinct reaction paths on the doublet PES have been found, i.e., a stepwise path and a concerted path. The latter is found to be the lowest energy path on the doublet PES to exothermic TiC₂H₂ ⁺(²A₂) + H₂ products, with the active barrier of 4.52 kcal/mol. In other words, this reaction proceeds in the following way: Ti⁺+C₂H₄→⁴IC→IM1-⁴B₂→^4,2ISC→IM1-²A₁→[²TS_ins]→IM2→[²TS_MCTS]→IM5→TiC₂H₂ ⁺(²A₂)+H₂. Supported by ‘Qinglan’ Talent Engineering Funds by Tianshui Normal University.     

Molecular modeling of hydration properties of hydrophobic ions Li<Superscript>+</Superscript>@C<Subscript>60</Subscript> and K<Superscript>+</Superscript>@C<Subscript>60</Subscript>

The Gibbs free energies of solvation (ΔG _s) and the electronic structures of endohedral metallofullerenes M⁺@C₆₀ (M⁺= Li⁺, K⁺) were calculated within the framework of the density functional theory and the polarizable continuum model. In water environment, the equilibrium position of K⁺ is at the center of the fullerene cavity whereas that of Li⁺ is shifted by 0.14 nm toward the fullerene cage. The Li⁺ cation is stabilized by interactions with both the fullerene and solvent. The equilibrium structures of both endohedral metallofullerenes are characterized by very close ΔG _s values. In particular, the calculated ΔG _s values for K⁺@C₆₀ are in the range from −124 to −149 kJ mol⁻¹ depending on the basis set and on the type of the density functional. Molecular dynamics simulations (TIP3P H₂O, OPLS force field, water sphere of radius 1.9 nm) showed that the radial distribution functions of water density around C₆₀ and M⁺@C₆₀ are very similar, whereas orientations of water dipoles around the endohedral metallofullerenes resemble the hydration pattern of isolated metal ions.     

Effects of La<Superscript>3+</Superscript> and Eu<Superscript>3+</Superscript> on outward potassium channels in Vicia guard cells

Effects of La³⁺ and Eu³⁺ on outward potassium channels (K_out⁺) in Vicia guard cells have been studied by patch clamping technique. Extracellular La³⁺ inhibited K_out⁺ currents with a half-inhibition concentration (IC₅₀) of 81 μmol·L⁻¹. Interestingly, intracellular La³⁺ activated K_out⁺ currents at a free concentration of 1.13 × 10⁻¹⁴ mol·L⁻¹, and inhibited K_out⁺ currents at a free concentration of 5.86 × 10⁻¹⁴ mol·L⁻¹. Extracellular Eu³⁺ also activated K_out⁺ currents at concentrations of 10 μmol·L⁻¹ and 50 μmol·L⁻¹, and inhibited K_out⁺ currents at concentrations of more than 1 mmol·L⁻¹. The effects of La³⁺ and Eu³⁺ on K_out⁺ currents may contribute to regulation of the plant water status, which may be one of the mechanisms of the biological effect of rare earth elements.