Macroporous ordered titanium dioxide (TiO2) inverse opal as a new label-free immunosensor

Photonic crystal sensing materials have been validated that they are very sensitive to refractive index changes. Herein, three-dimensionally ordered macroporous (3DOM) (>50 nm) TiO₂ inverse opal film has been fabricated by the self-assembly technique. Based on the TiO₂ inverse opal film, the optical spectrometer was established for label-free immunosensor. The sensing performance of the 3DOM TiO₂ was investigated using human IgG/goat anti-human IgG couple, which showed that the sensitivity of 3DOM TiO₂ inverse opal film could reach to 1 μg mL⁻¹ (equivalent to 1.5 pg mm⁻²) of protein concentration detection limit. The 3DOM TiO₂ inverse opal has a large internal surface area, low fluorescence background and unique optical properties. These characteristics indicated the feasibility of 3DOM TiO₂ inverse opal in label-free immunoassay.     

Surface chemistry and optical property of TiO2 thin films treated by low-pressure plasma

The low temperature RF plasma treatment was used to control the surface chemistry and optical property of TiO₂ thin films deposited by RF magnetron sputtering with a very good uniformity at 300 °C substrate heating temperature. The XRD pattern indicates the crystalline structure of the film could be associated to amorphous structure of TiO₂ in thin film. The plasma treatment of TiO₂ film can increase the proportion of Ti³⁺ in Ti2p and decrease in carbon atoms as alcohol/ether group in C1s at the surface. The optical transmittance of the film was enhanced by 50% after the plasma treatment. The surface structure and morphology remain the same for untreated and low-pressure plasma-treated films. Therefore, increase in the optical transmission could be due to change in surface chemistry and surface cleaning by plasma treatment.     

Preparation of TeOx–SiO2 film with excellent third-order nonlinear optical properties by electrochemically induced sol–gel method

TeO_x-SiO₂ composite films having third-order nonlinearities were prepared by electrochemically induced sol-gel deposition method on ITO substrate.The third-order optical nonlinearities of the films were measured by Z-scan technique.The third-order nonlinear susceptibilities(χ^（3）) of the as-prepared films are 5.9×10^-7 to 4.29×10^-6esu.The surface morphology and composition of the films were characterized by SEM/EDX,which identified that Te metallic particles well dispersed in TeO_x-SiO₂ gel films.     

Synthesis,Ferroelectric and Optical Properties of (Pb,Ca)TiO3 Thin Films by Soft Solution Processing

Calcium modified lead titanate sol was synthesized using a soft solution processing, the so-called polymeric precursor method. In soft chemistry method, soluble precursors such as lead acetate trihydrate, calcium carbonate and titanium isopropoxide, as starting materials, were mixed in aqueous solution. Pb_0.7Ca_0.3TiO₃ thin films were deposited on platinum-coated silicon and quartz substrates by means of the spinning technique. The surface morphology and crystal structure, dielectric and optical properties of the thin films were investigated. The electrical measurements were conducted on metal-ferroelectric-metal (MFM) capacitors. The typical measured small signal dielectric constant and dissipation factor at a frequency of 100 kHz were 299 and 0.065, respectively, for a thin film with 230 nm thickness annealed at 600°C for 2 h. The remanent polarization (2P_r) and coercive field (E _c) were 32 C/cm² and 100 kV/cm, respectively. Transmission spectra were recorded and from them, refractive index, extinction coefficient, and band gap energy were calculated. Thin films exhibited good optical transmissivity, and had optical direct transitions. The present study confirms the validity of the DiDomenico model for the interband transition, with a single electronic oscillator at 6.858 eV. The optical dispersion behavior of PCT thin film was found to fit well the Sellmeir dispersion equation. The band gap energy of the thin film, annealed at 600°C, was 3.56 eV. The results confirmed that soft solution processing provides an inexpensive and environmentally friendly route for the preparation of PCT thin films.     

Amperometric biosensor with HRP immobilized on a sandwiched nano-Au / polymerized m-phenylenediamine film and ferrocene mediator

An amperometric biosensor has been developed for the determination of H₂O₂ in plant samples. Horseradish peroxidase (HRP) is immobilized on a sandwiched nano-Au particle / m-phenylenediamine polymer film by glutaraldehyde cross-linking. The film is formulated on the carbon paste electrode (CPE) blended with ferrocene as an electron transfer mediator. On the low concentration range, the current response is related to the H₂O₂ concentration linearly from 0 to 8×10^-6 M with a detection limit of 1.3×10^-7 M. On a wider concentration range of 8×10^-6 to 1.4×10^-4 M, the reciprocal of current response is linearly related to the reciprocal of H₂O₂ concentration. The apparent Michaelis-Menten constant (K_m^app) was calculated to be 0.0334 mM. The sensor has been tested by determining H₂O₂ concentration in plant leaf samples.     

Preparation and Optical Properties of Gold-Dispersed BaTiO3, PGO (Pb5Ge3O11) and PLT (Pb1-1.5xLaxTiO3) Thin Films by Sol-Gel Process

Gold-dispersed BaTiO₃, PGO and PLT thin films, which will be used for third-order nonlinear optical devices, were prepared by sol-gel process with spin-coating using HAuCl₄4H₂O, Ba(CH₃COO)₂, Ti[O(CH₂)₃CH₃]₄, Pb(CH₃COO)₂3H₂O, Ge[O-n-C₄H₉]₄, La(CH₃COO)₃1.5 H₂O as starting materials. The thin films were heat-treated in air at temperatures ranging from 400 to 800 for 1 h. The nonlinear optical property of these thin films was measured by the degenerate four-wave mixing (DFWM) method using a frequency-doubled Nd: YAG laser with 20 ps pulse duration. Third-order nonlinear susceptibility χ⁽³⁾ of gold-dispersed BaTiO₃, PGO and PLT thin films with 5 vol% of gold were 1.410⁻⁶ esu, 3.510⁻⁷ esu respectively. The large χ⁽³⁾ may be ascribed to the high dielectric constant of the films.     

Synthesis and nonlinear optical properties of BaTi(BO3)2 and Ba3Ti3O6(BO3)2 crystals in glasses with high TiO2 contents

The ternary BaO-TiO₂-B₂O₃ glasses containing a large amount of TiO₂ (20-40 mol%) are prepared, and their optical basicities (Λ), the formation, structural features and second-order optical nonlinearities of BaTi(BO₃)₂ and Ba₃Ti₃O₆(BO₃)₂ crystals are examined to develop new nonlinear optical materials. It is found that the glasses with high TiO₂ contents of 30-40 mol% show large optical basicities of Λ=0.81-0.87, suggesting the high polarizabity of TiO_n polyhedra (n=4-6) in the glasses. BaTi(BO₃)₂ and Ba₃Ti₃O₆(BO₃)₂ crystals are found to be formed as main crystalline phases in the glasses. It is found that BaTi(BO₃)₂ crystals tend to orient at the surface of crystallized glasses. The new XRD pattern for the Ba₃Ti₃O₆(BO₃)₂ phase is proposed through Rietvelt analysis. The second harmonic intensities of crystallized glasses were found to be 0.8 times as large as α-quartz powders, i.e., I^2ω(sample)/I^2ω(α-quartz)=0.8, for the sample with BaTi(BO₃)₂ crystals and to be I^2ω(sample)/I^2ω(α-quartz)=68 for the sample with Ba₃Ti₃O₆(BO₃)₂ crystals. The Raman scattering spectra for these two crystalline phases are measured for the first time and their structural features are discussed.     

A new promising phosphor, Na3La2(BO3)3:Ln (Ln=Eu, Tb)

We present an efficient way to search a host for ultraviolet (UV) phosphor from UV nonlinear optical (NLO) materials. With the guidance, Na₃La₂(BO₃)₃ (NLBO), as a promising NLO material with a broad transparency range and high damage threshold, was adopted as a host material for the first time. The lanthanide ions (Tb³⁺ and Eu³⁺)-doped NLBO phosphors have been synthesized by solid-state reaction. Luminescent properties of the Ln-doped (Ln=Tb³⁺, Eu³⁺) sodium lanthanum borate were investigated under UV ray excitation. The emission spectrum was employed to probe the local environments of Eu³⁺ ions in NLBO crystal. For red phosphor, NLBO:Eu, the measured dominating emission peak was at 613 nm, which is attributed to ⁵D₀-⁷F₂ transition of Eu³⁺. The luminescence indicates that the local symmetry of Eu³⁺ in NLBO crystal lattice has no inversion center. Optimum Eu³⁺ concentration of NLBO:Eu³⁺ under UV excitation with 395 nm wavelength is about 30 mol%. The green phosphor, NLBO:Tb, showed bright green emission at 543 with 252 nm excited light. The measured concentration quenching curve demonstrated that the maximum concentration of Tb³⁺ in NLBO was about 20%. The luminescence mechanism of Ln-doped NLBO (Tb³⁺ and Eu³⁺) was analyzed. The relative high quenching concentration was also discussed.     

Composite film of carbon nanotubes and chitosan for preparation of amperometric hydrogen peroxide biosensor

A new amperometric biosensor for hydrogen peroxide was developed based on cross-linking horseradish peroxidase (HRP) by glutaraldehyde with multiwall carbon nanotubes/chitosan (MWNTs/chitosan) composite film coated on a glassy carbon electrode. MWNTs were firstly dissolved in a chitosan solution. Then the morphology of MWNTs/chitosan composite film was characterized by field-emission scanning electron microscopy. The results showed that MWNTs were well soluble in chitosan and robust films could be formed on the surface. HRP was cross-linked by glutaraldehyde with MWNTs/chitosan film to prepare a hydrogen peroxide biosensor. The enzyme electrode exhibited excellent electrocatalytic activity and rapid response for H₂O₂ in the absence of a mediator. The linear range of detection towards H₂O₂ (applied potential: −0.2 V) was from 1.67 × 10⁻⁵ to 7.40 × 10⁻⁴ M with correction coefficient of 0.998. The biosensor had good repeatability and stability for the determination of H₂O₂. There were no interferences from ascorbic acid, glucose, citrate acid and lactic acid.     

Electrochromism in Materials Prepared by the Sol-Gel Process

Electrochromism is defined as the persistent but reversible optical change (usually transmission) produced electrochemically. The preparation by the sol-gel process of thin films made of amorphous or crystalline nanoparticles of WO₃, V₂O₅, Nb₂O₅, TiO₂, CeO₂, Fe₂O₃ and mixed compounds such as WO₃−TiO₂, CeO₂−TiO₂, CeO₂−SnO₂, have opened remarkable new opportunities for obtaining electrochromic layers exhibiting large optical transmission variation in the UV, visible or infrared range and acceptable kinetics under H⁺ or Li⁺ insertion. In this paper we give an overview of what has been recently achieved in this field, with emphasis for cathodic electrochromic coatings of Nb₂O₅ and TiO₂ composition. Finally we stress the future developments in this fast growing field.     

Fabrication and optical conductivities of strained epitaxial NaxCoO2 thin films: x=0.5, 0.7

Epitaxial γ phase-Na_xCoO₂ thin films were deposited on (001) sapphire by the pulsed laser deposition method. To fabricate epitaxial Na_0.5CoO₂ thin films, we used a solution of iodine-dissolved acetonitrile and obtained an epitaxial Na_0.5CoO₂ thin film with a high crystallinity because of Na deintercalation of epitaxial Na_0.7CoO₂. From the spectroscopic ellipsometry analysis, we obtained the optical constants as well as the optical conductivities for the Na_0.5CoO₂ and Na_0.7CoO₂ thin films. The energy splitting between e_g and a_1g increased because of the structural strain of the Na_0.7CoO₂ thin film. It is inferred that the structural strain is the source for the lower resistivity and the preservation of the strongly correlated system up to 200 K for the Na_0.7CoO₂ thin film. On the other hand, the strain in the Na_0.5CoO₂ thin film was not affected, and the charge-ordering state and the Na content (x=0.5) only cause the charge-ordering state.     

Thermal and photochemical effects on the structure,morphology, thermal and optical properties of PVA/Ni0.04Zn0.96O and PVA/Fe0.03Zn0.97O nanocomposite films

Ni_0.04Zn_0.96O and Fe_0.03Zn_0.97O with average diameter of 23 and 19 nm, respectively, have been synthesized by a modified sol–gel method to be used in the preparation of (100 − x)/x poly(vinyl alcohol)/oxide nanocomposite films, with x = 0, 1, 3 and 5 (in wt.%). A 125 W-Hg vapor lamp with emission above 254 nmwas used to irradiate PVA/Ni_0.04Zn_0.96O and PVA/Fe_0.03Zn_0.97O films. The effect on their structural, thermal, morphological and optical properties was studied by TG, DSC, DRX, AFM, UV–vis and PL spectrophotometry. The Ni_0.04Zn_0.96O addition on PVA films decreases the thermal stability of the polymer in inert and in oxidative atmosphere. In contrast, the Fe_0.03Zn_0.97O presence in the PVA films seems to increase the thermal stability of the polymer. The characteristic peak of the crystalline phase of PVA and wurtzite phase of the zinc oxide were identified through X-ray diffraction in both films. The crystallinity of the PVA film increases with UV irradiation and with the presence of Ni_0.04Zn_0.96O and Fe_0.03Zn_0.97O. The roughness of the PVA film was not modified by the addition of the doped oxides; however, it increases after UV irradiation, more significantly in the films containing the oxides. The PVA film exhibits absorption around 280 nm characteristic of π–π^∗ transitions related to carbonyl groups from residuals acetate, while the 95/05 PVA/Ni_0.04Zn_0.96O and 95/05 PVA/Fe_0.03Zn_0.97O nanocomposite films show absorption at the visible region which is characteristics of the band gap reduction of the doped oxides. The photoluminescence of PVA was modified by the presence of the oxides in the film. These nanocomposite films are interesting due to their thermal, mechanical (flexible) properties and low cost of production. In addition they are also able to exhibit peculiar optical properties showing potential to be used in photonic devices, gas sensors and organic solar cell applications.     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.     

Bilayer lipid membrane biosensor with enhanced stability for amperometric determination of hydrogen peroxide

In this paper, a polydopamine (PDA) film is electropolymerized on the surface of bilayer lipid membrane (BLM) which is immobilized with horseradish peroxidase (HRP). The coverage of the PDA film on HRP/BLM electrode is monitored by electrochemical impedance spectroscopy (EIS). The electrocatalytic reduction of H₂O₂ at the PDA/HRP/BLM electrode is studied by means of cyclic voltammetry (CV). The biosensor has a fast response to H₂O₂ of less than 5 s and an excellent linear relationship is obtained in the concentration range from 2.5 × 10⁻⁷ to 3.1 × 10⁻³ mol L⁻¹, with a detection limit of 1.0 × 10⁻⁷ mol L⁻¹ (S/N = 3). The response current of BLM/HRP/PDA biosensor retains 84% of its original response after being stored in 0.1 mol L⁻¹ pH 7.0 PBS at 4 °C for 3 weeks. The selectivity, repeatability, and storage stability of PDA/HRP/BLM biosensor are greatly enhanced by the coverage of polydopamine film on BLM.     

Synthesis, crystal structure and nonlinear optical property of Rb3V5O14

The new nonlinear optical crystal Rb₃V₅O₁₄ has been synthesized by solid state reaction and characterized by single-crystal X-ray diffraction, IR and thermogravimetric analysis. The crystal Rb₃V₅O₁₄ crystallizes in the trigonal system with space P31m (No. 157), a=b=8.7134(12) Å, c=5.2807(11) Å and α=90°, β=90°, γ=120°, Z=1, ρ=3.516 g/cm³. It is a layered structure that is very flat and strongly parallel to c. The V₅O₁₄ layer structure consists of corner-linked square and triangular pyramids. The layers are separated by Rb⁺ ions, which fit equally well on the V₅O₁₄ layer. The Kurtz powder SHG measurement, using 1064 nm radiation, showed that the second-harmonic generation efficiency of Rb₃V₅O₁₄ is about two times that of KDP.     

Li ion diffusion in Li4Ti5O12 thin film electrode prepared by PVP sol-gel method

Li₄Ti₅O₁₂ thin films for rechargeable lithium batteries were prepared by a sol-gel method with poly(vinylpyrrolidone). Interfacial properties of lithium insertion into Li₄Ti₅O₁₂ thin film were examined by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and potentiostatic intermittent titration technique (PITT). Redox peaks in CV were very sharp even at a fast scan rate of 50 mV s⁻¹, indicating that Li₄Ti₅O₁₂ thin film had a fast electrochemical response, and that an apparent chemical diffusion coefficient of Li⁺ ion was estimated to be 6.8×10⁻¹¹ cm² s⁻¹ from a dependence of peak current on sweep rates. From EIS, it can be seen that Li⁺ ions become more mobile at 1.55 V vs. Li/Li⁺, corresponding to a two-phase region, and the chemical diffusion coefficients of Li⁺ ion ranged from 10⁻¹⁰ to 10⁻¹² cm² s⁻¹ at various potentials. The chemical diffusion coefficients of Li⁺ ion in Li₄Ti₅O₁₂ were also estimated from PITT. They were in a range of 10⁻¹¹-10⁻¹² cm² s⁻¹.     

Structural, spectroscopic and photoluminescence studies of LiEu(WO4)2−x(MoO4)x as a near-UV convertible phosphor

A series of lithium europium double tungsto-molybdate phosphors LiEu(WO₄)_2−x(MoO₄)_x (x=0, 0.4, 0.8, 1.2, 1.6, 2.0) have been synthesized by solid-state reactions and their crystal structure, optical and luminescent properties were studied. As the molybdate content increases, the intensity of the ⁵D₀→⁷F₂ emission of Eu³⁺ activated at wavelength of 396 nm was found to increase and reach a maximum when the relative ratio of Mo/W is 2:0. These changes were found to be accompanied with the changes in the spectral feature, which can be attributed to the crystal field splitting of the ⁵D₀→⁷F₂ transition. As the molybdate content increases the emission intensity of the 615 nm peak also increases. The intense red-emission of the tungstomolybdate phosphors under near-UV excitation suggests them to be potential candidate for white light generation by using near-UV LEDs. In this study the effect of chemical compositions and crystal structure on the photoluminescent properties of LiEu(WO₄)_2−x(MoO₄)_x is investigated and discussed.     

High-performance thin-film Li4Ti5O12 electrodes fabricated by using ink-jet printing technique and their electrochemical properties

Li₄Ti₅O₁₂ thin-film anode with high discharge capacity and excellent cycle stability for rechargeable lithium ion batteries was prepared successfully by using ink-jet printing technique. The prepared Li₄Ti₅O₁₂ thin film were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, cyclic voltammograms, and galvanostatic charge–discharge measurements. It was found that the average thickness of 10-layer Li₄Ti₅O₁₂ film was about 1.7~1.8 μm and the active material Li₄Ti₅O₁₂ in the thin film was nano-sized about 50–300 nm. It was also found that the prepared Li₄Ti₅O₁₂ thin film exhibited a high discharge capacity of about 174 mAh/g and the discharge capacity in the 300th cycle retained 88% of the largest discharge capacity at a current density of 10.4 μA/cm² in the potential range of 1.0–2.0 V.     

Superstructure and stacking faults in hydrothermal-grown KBe2BO3F2 crystals

The structure of the hydrothermal-grown nonlinear optical crystal KBe₂BO₃F₂ was investigated. A new structure of the R3?c space group with cell parameters of a=4.422(1) Å and c=37.524(3) Å was obtained by powder X-ray diffraction and Rietveld refinement. The new structure is a 1×1×2 superstructure of the previously reported R32 structure with a different stacking sequence of (Be₂BO₃F₂)_∞ layers along the c axis. The relationship between the refined structure and the experimental results is discussed. A stacking fault mechanism is proposed for the formation of the superstructure as well as the nonuniformity of the hydrothermal-grown KBBF crystals.     

Influence of the crystallinity on the Li+ intercalation process in Nb2O5 films

Nb₂O₅ thin films were prepared by the Pechini method. The effect of the film crystallinity on the electrochemical and electrochromic properties was investigated. A relationship between the crystalline structure and the Li⁺ intercalation/extraction process, stability and kinetics was observed. A significant decrease in the electrochemical response was observed as a function of the number of cycles for films treated at 400 and 450 °C. However, as the calcination temperature increases this effect disappears. XRD studies shown that at 400 °C, the material is amorphous, evolving to orthorhombic phase. The transmittance variation as well as the coloration efficiency increases as the temperature is increased. In the initial cycles the intercalation charge is higher for the amorphous oxide than for the orthorhombic phase. However, the variation in the optical density is small. On the other hand, the charge of the orthorhombic phase oxide does not change. These results suggest that there are two different processes associated with Li⁺ intercalation, but only one of them leads to the coloration process.