Synthesis and electro‐optical properties of light‐emitting polymers containing oxadiazole derivatives for light‐emitting diodes applications

Two PPV‐based bipolar polymers containing 1,3,4‐oxadiazole pendant groups were synthesized via the Gilch polymerization reaction for use in light‐emitting diodes (LEDs). The resulting polymers were characterized using ¹H and ¹³C NMR, elemental analysis, DSC, and TGA. These polymers were found to be soluble in common organic solvents and are easily spin‐coated onto glass substrates, producing high optical quality thin films without defects. The electro‐optical properties of ITO/PEDOT/polymer/Al devices based on these polymers were investigated using UV‐visible, PL, and EL spectroscopy. The turn‐on voltages of the OC₁Oxa‐PPV and OC₁₀Oxa‐PPV devices were found to be 8.0 V. The maximum brightness and luminescence efficiency of the OC₁Oxa‐PPV device were found to be 544 cd/m² at 19 V and 0.15 cd/A, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1098–1110, 2008     

High‐efficiency doped polymeric organic light‐emitting diodes

Fabrication of polymer light‐emitting diodes based on emission from the phosphorescent molecule fac‐tris(2‐phenylpyridine) iridium doped into a poly(N‐vinyl carbazole) host are reported. For single‐layered devices with magnesium‐silver cathodes, the luminance efficiency at 20 mA/cm² was measured as 8.7 cd/A. This efficiency could be increased by over a factor of two by incorporation of evaporated small‐molecule layers into the device structure. Significant increases in device efficiency were also obtained without these evaporated layers by modification of the electrodes. Incorporation of 3,4‐poly(ethylene dioxythiophene):poly(styrene sulfonate) at the anode improved the device efficiency but had little impact on drive voltage. Insertion of lithium fluoride at the cathode resulted in no improvement in performance for magnesium‐silver and aluminum cathodes, but a significant improvement was realized in efficiency and drive voltage for calcium‐aluminum cathodes. Excellent device performance was observed for all three cathode metals used in conjunction with cesium fluoride. Through optimization of the electrodes and emitter‐layer thickness, devices exhibiting efficiencies as high as 37.3 cd/A are realized. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2715–2725, 2003     

Encapsulants for light‐emitting diodes from visible light‐cured epoxy monomers

During the last decade, light‐emitting diodes (LEDs) have replaced incandescent, fluorescent, and neon lamps due to their ability to produce high luminosity at low currents and voltages. LEDs are currently encapsulated by thermally curable epoxy resins. However, long periods of curing at high temperature result in high consumption of energy and require stringent process control to avoid failure of the devices. In addition, the thermal cure results in yellowing of the encapsulant, which decreases the efficiency of the LED. In recent years, photoinitiated polymerization has received much interest as it congregates a wide range of economic and ecological benefits. Cationic photoinitiators, such as diaryliodonium salts, generate Brønsted acid in situ, which initiates polymerization. The process can be triggered on demand by irradiating the mixture with light. Results from the present research reveal that cycloaliphatic epoxy monomers, photoactivated with an iodonium salt and Camphorquinone, polymerize readily under visible light irradiation (470 nm) in the absence of external heating. The partial replacement of cycloaliphatic epoxy with aromatic diglycidyl ether of bisphenol‐A (DGEBA) is an effective means of improving the refractive index of the material and consequently the efficiency of the photoemission. Visible light polymerization of DGEBA pure proceeds at a slow rate; however, it is enhanced by the increase in temperature during the polymerization of the highly reactive cycloaliphatic monomer. From results obtained in the present research, it may be concluded that visible light polymerization of epoxy monomers is a promising route for the processing of LED encapsulants. Copyright © 2013 John Wiley & Sons, Ltd.     

New series of highly phenyl‐substituted polyfluorene derivatives for polymer light‐emitting diodes

A new series of highly phenyl‐substituted polyfluorene derivatives were synthesized and characterized. The resulting polymers were amorphous and showed excellent solubility in common organic solvents, such as chloroform, tetrahydrofuran, xylene, toluene, chlorobenzene, and so forth. All possessed satisfied thermal stability with glass‐transition temperatures (T_g's) in the range of 79–115 °C. They emitted blue light with photoluminescent (PL) maximum peaks at about 408–412 nm in thin films. The PL efficiencies of the polymer films were measured around 30–33%. The highly phenylated pendants improved the T_g of polyfluorene without forming defects in the polymers and reduced their tendency to form aggregate/excimers. Polymer light‐emitting diodes were fabricated from these polymers with the configuration of indium tin oxide/polyethylenedioxythiophene:polystyrene sulfonic acid/polymer/Ba/Al, which emitted bright blue light with maximum peaks at 418–420 nm. The maximum external quantum efficiencies of these devices were 0.41–0.6%. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2985–2993, 2004     

Contact optimization in polymer light‐emitting diodes

To fully exploit the properties of light‐emitting polymers (LEPs) in electroluminescent applications, it is of paramount importance to develop efficient electrical contacts. An ideal electrode is highly conductive, stable, provides a low barrier to carrier injection, and does not degrade the LEP upon contact. It is difficult to find a single homogeneous material that satisfies all of these requirements. Hence, contact optimization has often required the development of multilayer structures. In particular, indium tin oxide covered by a film of poly(ethylene‐dioxythiophene):poly(styrene sulfonic acid) {ITO/PEDOT:PSS} has become a favorite combination for the transparent anode, and heterostructures of LiF and CsF with metals (Al and Ca) have proven to be efficient electron‐injecting contacts. Here we review our progress in the understanding of the operation of light‐emitting diodes incorporating such contacts, in particular by gauging the materials' energy‐level lineup via electroabsorption measurements. Among the series of LEDs investigated, using a high‐energy‐gap blue polyfuorene polymer, CsF/Ca/Al and LiF/Ca/Al electrodes lead to the best improvements in electron injection. The most promising performance for applications, where a high luminance (～1600 cd/m² at 5 V) is also accompanied by a high maximum efficiency (～3 lm/W), was obtained with LiF/Ca/Al cathodes and ITO/PEDOT:PSS anodes. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2649–2664, 2003     

Soluble polynorbornenes with pendant carbazole derivatives as host materials for highly efficient blue phosphorescent organic light‐emitting diodes

We report novel host polymers for a high‐efficiency polymer‐based solution‐processed phosphorescent organic light‐emitting diode with typical blue‐emitting dopant bis(4,6‐difluorophenylpyridinato‐N,C²)iridium(III) picolinate (FIrpic). The host polymers, soluble polynorbornenes with pendant carbazole derivatives, N‐phenyl‐9H‐carbazole ( P1 ), N‐biphenyl‐9H‐carbazole ( P2 ), and 9,9′‐(1,3‐phenylene)bis‐9H‐carbazole (mCP) ( P3 ) are efficiently synthesized by vinyl addition polymerization of norbornene monomers using Pd(II) catalyst in combination with 1‐octene chain transfer agent. The polymers exhibit high thermal stability with high decomposition (T_d5 > 410 °C) and glass transition temperatures (T_g ≈ 268 °C). The HOMO (ca. ?5.5 to ?5.7 eV) and LUMO (ca. ?2.0 to ?2.1 eV) levels with the high triplet energy of about 2.7–3.0 eV suggest that the polymers are suitable for a host material for blue emitters. Among the solution‐processed devices that were fabricated based on the emissive layers containing the P1 ? P3 host doped with various concentrations of FIrpic (7–13 wt %), the best device with P3 host exhibits power efficiency of 3.0 lm W^?1 and external quantum efficiency of 4.0% at a luminance of 1000 cd m^?2 that is outstanding among the polymeric rivals. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Poly(p‐phenylenevinylene) presenting pendent pentaphenylene dendron groups for light‐emitting diodes

We have synthesized, using the Gilch method, a novel poly(p‐phenylenevinylene) derivative (PPV‐PP) containing two pendent pentaphenylene dendritic wedges, and have characterized its structure and properties. The incorporated side chain pentaphenylene dendrons serve as solubilizing groups, prevent π‐stacking interactions from occurring between the polymer main chains, and suppress the formation of excimers in the solid state. Photoluminescence studies indicate that efficient intramolecular energy transfer occurred from the photoexcited pentaphenylene groups to the poly(p‐phenylenevinylene) backbone. The polymer film exhibits a maximum emission at 510 nm and had a photoluminescence efficiency of 46%, which is similar to that measured in dilute solution. The photoluminescence spectra remained almost unchanged after thermal annealing at 150 °C for 20 h, and displayed inhibited excimer formation. Polymer light‐emitting diodes that we fabricated in the configuration ITO/PEDOT/PPV‐PP/Mg:Ag/Ag exhibited a maximum emission peak at 513 nm, corresponding to the green region [x = 0.30 and y = 0.62 in the Commission Internationale de L'Eclairage (CIE) chromaticity coordinates]. The maximum brightness and maximum luminance efficiency were 1562 cd/m² and 1.93 cd/A, respectively. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5147–5155, 2005     

Synthesis of novel nitrogen‐ and sulfur‐containing conjugated polymers used as hole‐transporting materials for organic light‐emitting diodes

Two series of highly soluble novel nitrogen‐ and sulfur‐containing conjugated polymers were synthesized via an acid‐induced self‐polycondensation of functional monomers with methyl sulfinyl and aromatic groups. The well‐defined structures of synthesized polymers were confirmed by their NMR and IR spectra. The highest occupied molecular orbital energy values for these materials, estimated by cyclic voltammetry, showed a broad range of values from about 5.0 to 5.2 eV used as hole‐transport layers (HTL) in two‐layer light‐emitting diodes ITO/HTL/Alq₃/Mg:Ag [ITO = indium tin oxide, and Alq₃ = tris(8‐quinolinato) aluminum]. The typical turn‐on voltage of these diodes was about 4–5 V. The maximum brightness of the device was about 3440 cd/m² at 20 V. The maximum efficiency was estimated to be 0.15 lm/W at 10 V. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1321–1333, 2002     

Copolyfluorenes containing phenothiazine or thiophene derivatives: Synthesis,characterization, and application in white‐light‐emitting diodes

Four copolyfluorenes chemically doped with 0.1 and 1 mol % 3,7‐bis[2‐thiophene‐2‐yl)‐2‐cyanovinyl]phenothiazine ( PFPhT ) or 2,5‐bis[2‐(thiophene‐2‐yl)‐2‐cyanovinyl]thiophene chromophores ( PFThT ) were synthesized using the Suzuki coupling reaction and applied in white‐light‐emitting devices. They were characterized by GPC, elemental analysis, DSC, TGA, optical spectra, and cyclic voltammetry. They exhibited good thermal stability (T_d > 420 °C) and moderate glass transition temperatures (>95 °C). The PhT‐Br and ThT‐Br showed PL peaks at 586 and 522 nm (with a shoulder at 550 nm). In film state, PL spectra of the copolymers comprised emissions from the fluorene segments and the chromophores due to incomplete energy transfer. Both monomers exhibited low LUMO levels around ?3.50 to ?3.59 eV, whereas the PhT‐Br owned the higher HOMO level (?5.16 eV) due to its electron‐donating phenothiazine core. Light‐emitting diodes with a structure of ITO/PEDOT:PSS/copolymer/Ca(50 nm)/Al(100 nm) showed broad emission depending on the chromophore contents. The maximum brightness and maximum current efficiency of PFPhT2 ( PFThT1 ) device were 8690 cd/m² and 1.43 cd/A (7060 cd/m² and 0.98 cd/A), respectively. White‐light emission was realized by further blending PFPhT2 with poly(9,9‐dihexylfluorene) (w/w = 10/1), with the maximum brightness and maximum current efficiency being 10,600 cd/m² and 1.85 cd/A. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 833–844, 2009     

Synthesis and characterization of fluorene‐based copolymers containing benzothiadiazole derivative for light‐emitting diodes applications

Five new thermally robust electroluminescent fluorene‐based conjugated copolymers, including poly[2,7‐(9,9‐dioctylfluorene)‐co‐4,7‐{5,6‐bis(3,7‐dimethyloctyloxymethyl)‐2,1,3‐(benzothiadiazole)}] ( PFO‐P2C₁₀BT ) were synthesized and used to fabricate the efficient polymer light‐emitting diodes (PLEDs). The glass transition temperatures of the polymers were found to be higher than that of poly(9,9‐dialkylfluorenes) and are in the range 113–165 °C. We fabricated PLEDs in indium‐tin oxide/PEDOT/light‐emitting polymer/cathode configurations using either double‐layer LiF/Al or triple‐layer Alq₃/LiF/Al cathode structures. The new copolymers were found to have emission colors that vary from greenish blue (491 nm) to green (543 nm) depending on the copolymer composition. The maximum brightness and luminance efficiency of these PLEDs were found to be up to 5347 cd/m² and 1.51 cd/A at 10 V, respectively. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6762–6769, 2008     

Homologous series of alkylsilylphenyl‐substituted poly (p‐phenylenevinylene)s for light‐emitting diodes

Substituent‐induced electroluminescence polymers—poly[2‐(2‐dimethyldodecylsilylphenyl)‐1,4‐phenylenevinylene] [(o‐R₃Si)PhPPV], poly[2‐(3‐dimethyldodecylsilylphenyl)‐1,4‐phenylenevinylene] [(m‐R₃Si)PhPPV], and poly[2‐(4‐dimethyldodecylsilylphenyl)‐1,4‐phenylenevinylene] [(p‐R₃Si)PhPPV]—were synthesized according to the Gilch polymerization method. The band gap and spectroscopic data were tuned by the dimethyldodecylsilyl substituent being changed from the ortho position to the para position in the phenyl side group along the polymer backbone. The weight‐average molecular weights and polydispersities were 8.0–96 × 10⁴ and 3.0–3.4, respectively. The maximum photoluminescence wavelengths for (o‐R₃Si)PhPPV, (m‐R₃Si)PhPPV, and (p‐R₃Si)PhPPV appeared around 500–530 nm in the green emission region. Double‐layer light‐emitting diodes with an indium tin oxide/poly(3,4‐ethylenedioxythiophene)/polymer/Al configuration were fabricated with these polymers. The turn‐on voltages and the maximum brightness of (o‐R₃Si)PhPPV, (m‐R₃Si)PhPPV, and (p‐R₃Si)PhPPV were 6.5–8.7 V and 1986–5895 cd/m², respectively. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2347–2355, 2004     

Synthesis and characterization of stable blue light‐emitting poly(spirobifluorene) derivatives containing alkoxy group

Polymers containing alkoxy‐substituted spirobifluorene have been prepared from nickel(0)‐mediated coupling or palladium‐catalyzed Suzuki coupling. The polymers were characterized using various spectroscopies, such as ¹H‐NMR, FT‐IR, and elemental analysis. The high glass transition temperature and high decomposition temperature suggested that the resulting polymers possessed a high thermal stability. The obtained polymers possessed weight average molecular weight of 4500–33,000 with polydispersity index of 1.1–1.9 and good solubility. The low onsets of the oxidation potential suggested that the polymers containing alkoxy substituted spirobifluorene possessed a good hole injection property. The photoluminescence and electroluminescence of the polymers containing alkoxy substituted spirobifluorene showed stable blue color by suppressing the excimer formation due to intermolecular interaction. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2316–2324, 2005     

Synthesis and characterization of naphthyl‐substituted poly(p‐phenylenevinylene)s with few structural defects for polymer light‐emitting diodes

A series of naphthyl‐substituted poly(p‐phenylenevinylene)s (2N‐PPV, 4N‐PPV, and NAP‐PPV) has been synthesized and characterized by Fourier transform IR, ¹H NMR, and elemental analysis. The polymers possess excellent solubility, high molecular weights, good thermal stability, and high photoluminescence efficiencies. Thermogravimetric analysis reveals the onset of degradation to be 347, 301, and 306 °C for 2N‐PPV, 4N‐PPV, and NAP‐PPV, respectively. The differential scanning calorimetry investigation gives the respective glass‐transition temperature values of 118, 135, and 141 °C. The UV and photoluminescence spectra measurements reveal that the polymers exhibit similar optical properties, indicating that side‐chain substitution has little effect on the optical properties of this series of polymers. Proton NMR measurement of the signal due to tolane–bisbenzyl defects at around 2.7 ppm indicates that all the polymers have negligible amounts of tolane–bisbenzyl defects along the polymer main chain as a result of the steric bulk imposed by the naphthalene side chain. The highest occupied and lowest unoccupied molecular orbital energy levels of the polymers are investigated through cyclic voltammetry. Polymer light‐emitting diodes utilizing the polymers as the emissive layer with a configuration of indium tin oxide/poly(3,4‐ethylenedioxythiophene)/polymer/Ba/Al are fabricated and evaluated. The diodes emit blue‐green to yellow‐green light with maximum peaks at 518, 542, and 486 nm for 2N‐PPV, 4N‐PPV, and NAP‐PPV, respectively. The respective turn‐on electric fields of the diodes are 0.84, 0.69, and 0.83 MV/cm and the respective maximum external quantum efficiencies are 0.08, 0.54, and 0.02%. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1647–1657, 2004     

Enhanced efficiency of polyfluorene derivatives: Organic–inorganic hybrid polymer light‐emitting diodes

Two novel organic–inorganic hybrid polyfluorene derivatives, poly{(9,9′‐dioctyl‐2,7‐fluorene)‐co‐(9,9′‐di‐POSS‐2,7‐fluorene)‐co‐[2,5‐bis(octyloxy)‐1,4‐phenylene]} (PFDOPPOSS) and poly{(9,9′‐dioctyl‐2,7‐fluorene)‐co‐(9,9′‐di‐POSS‐2,7‐fluorene)‐co‐bithiophene} (PFT2POSS), were synthesized by the Pd‐catalyzed Suzuki reaction of polyhedral oligomeric silsesquioxane (POSS) appended fluorene, dioctyl phenylene, and bithiophene moieties. The synthesized polymers were characterized with ¹H NMR spectroscopy and elemental analysis. Photoluminescence (PL) studies showed that the incorporation of the POSS pendant into the polyfluorene derivatives significantly enhanced the fluorescence quantum yields of the polymer films, likely via a reduction in the degree of interchain interaction as well as keto formation. Additionally, the blue‐light‐emitting polyfluorene derivative PFDOPPOSS showed high thermal color stability in PL. Moreover, single‐layer light‐emitting diode devices of an indium tin oxide/poly(3,4‐ethylene dioxythiophene):poly(styrene sulfonate)/polymer/Ca/Al configuration fabricated with PFDOPPOSS and PFT2POSS showed much improved brightness, maximum luminescence intensity, and quantum efficiency in comparison with devices fabricated with the corresponding pristine polymers PFDOP and PFT2. In particular, the maximum external quantum efficiency of PFT2POSS was 0.13%, which was twice that of PFT2 (0.06%), and the maximum current efficiency of PFT2POSS was 0.38 cd/A, which again was twice that of PFT2 (0.19 cd/A). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2943–2954, 2006     

Synthesis of thermal‐stable and photo‐crosslinkable polyfluorenes for the applications of polymer light‐emitting diodes

Three polyfluorene derivatives which have oxetane‐containing phenyl group at C‐9 position were synthesized via the palladium‐catalyzed Suzuki‐coupling reaction. The synthesized polymers PFB, PFG, and PFR emit blue, green, and red light, respectively. A double‐layer device with the configuration of ITO/PEDOT/polymer/Ca/Al using PFB as the active layer showed a threshold voltage of 5 V, a maximum brightness of 2030 cd/m², and a maximum current efficiency of 0.35 cd/A. Using PFG as the active layer, the device exhibited a threshold voltage of 6 V, a maximum brightness of 6447 cd/m², and a maximum current efficiency of 1.27 cd/A. Using PFR as the active layer, the device showed a threshold voltage of 4 V, a maximum brightness of 2135 cd/m², and a maximum current efficiency of 0.16 cd/A. Better electroluminescent performance was also found based on different design of device structures. Due to photo‐crosslinking property of oxetane groups, the UV‐exposed thin films are insoluble in common organic solvents. A device comprised of blue, green, and red‐emissive pixels was successfully fabricated by spin‐coating and photo‐lithographic processes. In addition, a white light‐emitting device with CIE coordinate of (0.34, 0.33) was achieved by blending PFR into a host material PFB as the active layer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 516–524, 2010     

Hyperbranched poly(arylene ethynylene)s with triphenylamine core for polymer light‐emitting diodes

A series of light‐emitting hyperbranched poly(arylene ethynylene)s (HB‐PAEs) were prepared by the Sonogashira coupling from bisethynyl of carbazole, fluorene, or dialkoxybenzenes (A₂ type) and tris(4‐iodophenyl)amine (B₃ type). For comparison, two linear polymers (L‐PAEs) of the HB analogs were also synthesized. The polymers were characterized by Fourier transform infrared, NMR, and GPC. The HB polymers showed excellent solubility in chloroform, THF, and chlorobenzene when compared with their linear analogs. The number‐average molecular weight (M_n) of the polymers determined from GPC was found to be in the range of 18,600–34,200. The polymers were thermally stable up to 298–330 °C with only 5% weight loss. The absorption maxima of the polymers were between 354 and 411 nm with optical band gap in the range of 2.5–2.9 eV. The HB polymers were found to be highly fluorescent with photoluminescence quantum yields around 33–42%. The highest occupied molecular orbital energy levels of the polymers calculated from onset oxidation potentials were found to be in the range from ?5.83 to ?6.20 eV. Electroluminescence (EL) properties of three HB‐PAEs and one L‐PAE were investigated with device configuration ITO/PEDOT:PSS/Polymer/LiF/Al. The EL maxima of HB‐PAEs were found to be in the range of 507–558 nm with turn‐on voltages around 7.5–10 V and maximum brightness values of 316–490 cd/m². At the same time, linear analog of one HB‐PAE was found to show a maximum brightness of 300 cd/m² at a turn‐on voltage of 8.2 V. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Donor–acceptor copolymers for red‐ and near‐infrared‐emitting polymer light‐emitting diodes

We report a comparative study of two organic soluble, vinylene‐based, alternating donor–acceptor copolymers with 1,4‐(2,5‐dihexadecyloxyphenylene) as the donor; the acceptor is either a 2,5‐linked pyridine or a 5,8‐linked 2,3‐diphenylpyrido[3,4‐b]pyrazine. The polymers are synthesized via a Heck coupling methodology from a dihalo monomer and a divinyl monomer to yield number‐average molecular weights of 16,000 g/mol for the pyridine polymer (PPyrPV) and 6500 g/mol for the pyridopyrazine polymer (PPyrPyrPV), with high solubility in common chlorinated solvents and lower solubility in less polar solvents (e.g., tetrahydrofuran). Thin‐film measurements show band gaps of 2.2 and 1.8 eV for PPyrPV and PPyrPyrPV, respectively. Both polymers exhibit photoluminescence in solution and in the solid state and exhibit electroluminescence when incorporated into light‐emitting diodes. In this case, a broad red emission centered at 690 nm for PPyrPV and a near‐infrared emission centered at 800 nm for PPyrPyrPV have been observed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1417–1431, 2005     

Pyrene‐functionalized oligofluorenes as non‐doped deep blue emitters for solution‐processed organic light‐emitting diodes

Two pyrene‐functionalized oligofluorenes (TPA‐PyF₃ and CBP‐PyF₃) are prepared using the condensation reaction by the Friedel–Crafts procedure. In the produced oligomers, the triphenylamine or N,N′‐dicarbazolyl‐4,4′‐biphenyl core serves as a spacer bearing spiro‐linked fluorene moieties to form a multi‐H shaped structure. This specific structure efficiently retards the crystallization tendency of the pyrene groups, and gives the materials completely amorphous morphological structure and film forming ability. Solution‐processed OLEDs with the structure of ITO/PEDOT:PSS (25 nm)/TPA‐PyF₃ or CBP‐PyF₃ (40 nm)/TPBI (35 nm)/Ca (10 nm)/Ag (100 nm) show low turn‐on voltages of 3.6 V, and the maximum external quantum efficiencies reach 1.78% and 2.07% for TPA‐PyF₃ and CBP‐PyF_3, respectively. Moreover, both devices exhibit stable deep‐blue light emission with Commission International de I'Eclairage (CIE) coordinates of around (0.16, 0.09) at the brightness of 100–1000 cd m^?2. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 795–801     

Chromophore‐labeled dendrimers for use in single‐layer light‐emitting diodes

Two novel chromophore‐labeled dendrimers are presented and their incorporation into two‐component, single layer organic light emitting diodes (OLEDs) is described. The photoluminescence (PL) spectra, both in solution and in the solid state, demonstrate that Forster energy transfer from the donor chromophores on the dendrimers periphery to the acceptors located at the core is highly efficient, and affords emission exclusively from the core dyes, either coumarin 343 or a benzene‐capped pentathiophene. When these dendrimers are doped into single layer OLEDs, the electroluminescence (EL) is nearly identical to the photoluminescence described above, indicating once again exclusive emission from the core chromophores.