Fabrication of large-area ferromagnetic arrays using etched nanosphere lithography

Nanosphere lithography (NSL) is a simple, cost-effective, and powerful technique capable of producing large-area arrays of ferromagnetic nanostructures with dimensions below 100 nm. These properties make NSL an attractive process for the fabrication of arrays of magnetic elements with applications in magnetic data storage. The main disadvantage with conventional NSL is that the monolayer of spheres always contains imperfections that are transferred to the resulting nanostructures. This can significantly affect the structural and magnetic properties of the fabricated array. In this paper we present a novel adaptation of NSL that reduces the effect of such defects on the resulting nanostructures. The technique also offers excellent control over the diameter, aspect ratio, and pitch of the fabricated elements. These properties are demonstrated through the fabrication of arrays of Ni elements of 210 nm diameter and arrays of Co elements with diameters between 200 and 320 nm.     

Nanostructures of functionalized gold nanoparticles prepared by particle lithography with organosilanes

Periodic arrays of organosilane nanostructures were prepared with particle lithography to define sites for selective adsorption of functionalized gold nanoparticles. Essentially, the approach for nanoparticle lithography consists of procedures with two masks. First, latex mesospheres were used as a surface mask for deposition of an organosilane vapor, to produce an array of holes within a covalently bonded, organic thin film. The latex particles were readily removed with solvent rinses to expose discrete patterns of nanosized holes of uncovered substrate. The nanostructured film of organosilanes was then used as a surface mask for a second patterning step, with immersion in a solution of functionalized nanoparticles. Patterned substrates were fully submerged in a solution of surface-active gold nanoparticles coated with 3-mercaptopropyltrimethoxysilane. Regularly shaped, nanoscopic areas of bare substrate produced by removal of the latex mask provided sites to bind silanol-terminated gold nanoparticles, and the methyl-terminated areas of the organosilane film served as an effective resist, preventing nonspecific adsorption on masked areas. Characterizations with atomic force microscopy demonstrate the steps for lithography with organosilanes and functionalized nanoparticles. Patterning was accomplished for both silicon and glass substrates, to generate nanostructures with periodicities of 200-300 nm that match the diameters of the latex mesospheres of the surface masks. Nanoparticles were shown to bind selectively to uncovered, exposed areas of the substrate and did not attach to the methyl-terminal groups of the organosilane mask. Billions of well-defined nanostructures of nanoparticles can be generated using this high-throughput approach of particle lithography, with exquisite control of surface density and periodicity at the nanoscale.     

Superhydrophobic silicon surfaces with micro-nano hierarchical structures via deep reactive ion etching and galvanic etching

An effective fabrication method combining deep reactive ion etching and galvanic etching for silicon micro-nano hierarchical structures is presented in this paper. The method can partially control the morphology of the nanostructures and enables us to investigate the effects of geometry changes on the properties of the surfaces. The forming mechanism of silicon nanostructures based on silver nanoparticle galvanic etching was illustrated and the effects of process parameters on the surface morphology were thoroughly discussed. It is found that process parameters have more impact on the height of silicon nanostructure than its diameter. Contact angle measurement and tilting/dropping test results show that as-prepared silicon surfaces with hierarchical structures were superhydrophobic. What's more, two-scale model composed of micropillar arrays and nanopillar arrays was proposed to study the wettability of the surface with hierarchical structures. Wettability analysis results indicate that the superhydrophobic surface may demonstrate a hybrid state at which water sits on nanoscale pillars and immerses into microscale grooves partially.     

憎水性金纳米粒子的制备、表征与形貌控制

在十六烷基三甲基溴化铵(CTAB)或十八胺(C18NH2)/正庚烷/乙醇/HAuCl4.4H2O W/O型微乳液体系中,利用简单的加热手段通过乙醇还原法制备了具有不同形貌和尺寸的憎水性金纳米材料。由CTAB或C18NH2稳定的金纳米颗粒运用紫外可见光谱(UV-vis)、透射电镜(TEM)和X射线衍射(XRD)等分别进行了表征和分析。用混合表面活性剂(CTAB/C18NH2)替代单一表面活性剂(CTAB)可以削弱CTAB对金纳米晶体生长的导向作用并提高粒子的单分散性。     

Fabrication of heterogeneous binary arrays of nanoparticles via colloidal lithography

Heterogeneous binary arrays of metallic nanoparticles have been constructed by consecutively depositing gold and silver into monolayers of hexagonally close-packed latex spheres at the incidence angles of 15 and -15 degrees, followed by removal of the colloidal masks. The present approach is independent of the chemical nature of both colloidal masks and deposition materials. The pattern feature of the resulting binary nanoparticle arrays is dependent on the colloidal mask registry.     

Green preparation of hollow mesoporous silica nanosphere inside-loaded gold nanoparticles and the catalytic activity

In this work, an active nano-catalyst with gold nanoparticles loaded in hollow mesoporous silica nanospheres (HMSNs/Au) was prepared by a one-pot sol-gel method, in which gold ions were loaded in hollow mesoporous silica spheres followed by sodium alginate reduction. The characterization of the HMSNs/Au were determined by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), N₂ adsorption–desorption isotherms (BET). The high catalytic activity of HMSNs/Au, denoted as apparent turn-over frequency (TOF), was detected by UV-Vis spectrophotometer for the catalytic reduction of 4-nitrophenol (74.5 h^?1) and 2-nitrophenol (108.7 h^?1) in the presence of sodium borohydride solution due to the small gold nanoparticles size and overall exposure of active sites. It is expected that this ecofriendly approach to prepare inorganic composited nanoparticles as high active catalysts based on hollow mesoporous materials was a promising platform for loading noble metal nanoparticles.     

Microfluidic cells with interdigitated array gold electrodes: Fabrication and electrochemical characterization

Microfluidic flow cells combined with an interdigitated array (IDA) electrode and/or individually driven interdigitated electrodes were fabricated and characterized for application as detectors for flow injection analysis. The gold electrodes were produced by a process involving heat transfer of a toner mask onto the gold surface of a CD-R and etching of the toner-free gold region by short exposure to iodine-iodide solution. The arrays of electrodes with individual area of 0.01 cm² (0.10 cm of length × 0.10 cm of width and separated by gaps of 0.05 or 0.03 cm) were assembled in microfluidic flow cells with 13 or 19 μm channel depth. The electrochemical characterization of the cells was made by voltammetry under stationary conditions and the influence of experimental parameters related to geometry of the channels and electrodes were studied by using K₄Fe(CN)₆ as model system. The obtained results for peaks currents (I_p) are in excellent agreement with the expected ones for a reversible redox system under stationary thin-layer conditions. Two different configurations of the working electrodes, E_i, auxiliary electrode, A, and reference electrode, R, on the chip were examined: E_i/R/A and R/E_i/A, with the first presenting certain uncompensated resistance. This is because the potentiostat actively compensates the iR drop occurring in the electrolyte thin layer between A and R, but not from R to each E_i. This is confirmed by the smaller difference between the cathodic and anodic peak potentials for the second configuration. Evaluation of the microfluidic flow cells combined with (individually driven) interdigitated array electrodes as biamperometric or amperometric detectors for FIA reveals stable and reproducible operation, with peak heights presenting relative standard deviations of less than 2.2%. For electrochemically reversible species, FIA peaks with enhanced current signal were obtained due to redox cycling under flow operation. The versatility of microfluidic flow cells, produced by simple and low-cost technique, associated with the rich information content of electrochemical techniques with arrays of electrodes, opens many future research and application opportunities.     

Block copolymer-mediated synthesis of size-tunable gold nanospheres and nanoplates

We have successfully controlled the size and shape of isotropic and anisotropic gold nanocrystals through a one-step reaction by using amphiphilic polyethylene oxide-polystyrene oxide block copolymers as both reductant and stabilizing agents in water solution. Spherical or quasispherical nanoparticles were obtained at room temperature with tunable mean sizes and polydispersities depending on reaction conditions, that is, on copolymer block length, and copolymer and gold salt concentrations. By moderate increases of reaction temperature up to 65 degrees C, progressive formation of single-crystalline gold nanoplates in good yields takes place (up to 70%) without the necessity of additional reactants or growing solutions. These nanoplates are characterized by lateral mean sizes between 0.1-1.2 microm depending on copolymer concentration and reaction temperature, with mainly truncated or rounded triangular shapes with {111} planes as two basal surfaces. This allows us to tune the surface plasmon band of the nanoplates from ca. 850 nm to more than 1100 nm, well inside the near-infrared region (NIR), which enables the use of these type of nanostructures as a very promsing materials in applications such as optical coatings, SERS, and cancer cell hyperthermia. We proposed that the growth of these nanostructures can stem from a decrease in the reaction rate as temperature increases due to an enhanced copolymer hydrophobicity, which gives rise to a structure of interacting micelles formed from the fluid via a percolation transition (known as "soft gel") at elevated temperatures. In this way, reduction becomes slow enough to allow kinetic control of the reaction, and preferential adsorption of the copolymer molecules/micelles on certain crystallographic planes can favor the growth of certain nanocrystal facets to give the final structure. This alternative water-based system provides a more convenient and environmentally benign route to the synthesis of shape-controlled noble-metal nanocrystals in high yield because it does not involve toxic organic solvents or reagents and serves as a bridge between two frontline discipline: the block copolymeric science and anisotropic nanoparticles.     

Fabrication and electrochemical application of three-dimensional gold nanoparticles: self-assembly

Multilayers film of nanostructured citrate-stabilized gold particles (AuNPs) has been fabricated based on the layer-by-layer (LBL) technique using a self-assembled monolayer of 1,4-benzenedimethanethiol (BDMT). The formation of AuNPs and BDMT self-assemblies as alternative multilayers was confirmed by transmission electron microscopy (TEM), X-ray photoelectron spectroscope (XPS), and quartz crystal microbalance (QCM). The formation of uniform AuNP layers with an average monolayer thickness of 5-6 nm was obvious in the TEM images. The existence of BDMT molecules as cross linkers for the AuNPs' layers was proved by XPS measurements. The greater affinity of AuNPs' layers to bind BDMT molecules in comparison with the bare Au bulk electrode was revealed by QCM measurements. Electrochemically, the AuNPs' layers on the electrode surface did not only catalyze the reduction of oxygen (ca. 100-mV positive shift of the reduction peak potential compared with that at the bare Au bulk electrode) but also showed a fascinating nature of working as a renewed activated-electrode surface; a zigzag response was observed for oxygen reduction during alternative immobilization of BDMT and the AuNP layer. The self-assembly of a new AuNPs layer restored the catalytic activity that was entirely blocked by the preceding BDMT layer.     

Preparation of high-quality colloidal mask for nanosphere lithography by a combination of air/water interface self-assembly and solvent vapor annealing

Nanosphere lithography (NSL) has been regarded as an inexpensive, inherently parallel, high-throughput, materials-general approach to the fabrication of nanoparticle arrays. However, the order of the resulting nanoparticle array is essentially dependent on the quality of the colloidal monolayer mask. Furthermore, the lateral feature size of the nanoparticles created using NSL is coupled with the diameter of the colloidal spheres, which makes it inconvenient for studying the size-dependent properties of nanoparticles. In this work, we demonstrate a facile approach to the fabrication of a large-area, transferrable, high-quality latex colloidal mask for nanosphere lithography. The approach is based on a combination of the air/water interface self-assembly method and the solvent-vapor-annealing technique. It enables the fabrication of colloidal masks with a higher crystalline integrity compared to those produced by other strategies. By manipulating the diameter of the colloidal spheres and precisely tuning the solvent-vapor-annealing process, flexible control of the size, shape, and spacing of the interstice in a colloidal mask can be realized, which may facilitate the broad use of NSL in studying the size-, shape-, and period-dependent optical, magnetic, electronic, and catalytic properties of nanomaterials.     

Tailoring ordered taper-nanopore arrays by combined nanosphere self-assembling, imprinting, anodizing and etching

We report a simple and effective method for tailoring ordered three-dimensional alumina taper-nanopore arrays, dispensing with any unavailable and expensive top-down equipment.     

Mercaptocarborane-capped gold nanoparticles: electron pools and ion traps with switchable hydrophilicity

A simple single-phase method for the preparation of ca. 2 nm gold nanoparticles capped with mercaptocarborane ligands is introduced. The resultant monolayer protected clusters (MPCs) exhibit redox-dependent solubility and readily phase transfer between water and nonpolar solvents depending on the electronic and ionic charge stored in the metal core and in the ligand shell, respectively. The particles and their properties have been characterized by high angle annular dark field imaging in a scanning transmission electron microscope, elemental analysis, centrifugal particle sizing, UV-vis and FTIR spectroscopy, and thermogravimetric analysis and by (1)H, (11)B, and (7)Li NMR spectroscopy. Cellular uptake of the MPCs by HeLa cells has been studied by TEM, and the subsequent generation of reactive oxygen species inside the cells has been evaluated by confocal fluorescence microscopy. These MPCs qualitatively showed significant toxicity and the ability to penetrate into most cell compartments with a strong tendency of finally residing inside membranes. Applications in catalysis, electrocatalysis, and biomedicine are envisaged.     

Synthesis and characterization of pore size-tunable magnetic mesoporous silica nanoparticles

Magnetic mesoporous silica nanoparticles (M-MSNs) are emerging as one of the most appealing candidates for theranostic carriers. Herein, a simple synthesis method of M-MSNs with a single Fe(3)O(4) nanocrystal core and a mesoporous shell with radially aligned pores was elaborated using tetraethyl orthosilicate (TEOS) as silica source, cationic surfactant CTAB as template, and 1,3,5-triisopropylbenzene (TMB)/decane as pore swelling agents. Due to the special localization of TMB during the synthesis process, the pore size was increased with added TMB amount within a limited range, while further employment of TMB lead to severe particle coalescence and not well-developed pore structure. On the other hand, when a proper amount of decane was jointly incorporated with limited amounts of TMB, effective pore expansion of M-MSNs similar to that of analogous mesoporous silica nanoparticles was realized. The resultant M-MSN materials possessed smaller particle size (about 40-70 nm in diameter), tunable pore sizes (3.8-6.1 nm), high surface areas (700-1100 m(2)/g), and large pore volumes (0.44-1.54 cm(3)/g). We also demonstrate their high potential in conventional DNA loading. Maximum loading capacity of salmon sperm DNA (375 mg/g) was obtained by the use of the M-MSN sample with the largest pore size of 6.1 nm.     

Fabrication of electroactive layer-by-layer films of myoglobin with gold nanoparticles of different sizes

Alternate adsorption of oppositely charged myoglobin (Mb) and gold nanoparticles with different sizes were used to assemble {Au/Mb}n layer-by-layer films on solid surfaces by electrostatic interaction between them. The direct electrochemistry of Mb was realized in {Au/Mb}n films at pyrolytic graphite (PG) electrodes, showing a pair of well-defined, nearly reversible cyclic voltammetry (CV) peaks for the Mb heme FeIII/FeII redox couple. Quartz crystal microbalance (QCM), electrochemical impedance spectroscopy (EIS), and CV were used to monitor or confirm the growth of the films. Compared with other Mb layer-by-layer films with nonconductive nanoparticles or polyions, {Au/Mb}n films showed much improved properties, such as smaller electron-transfer resistance (Rct) measured by EIS with Fe(CN)3-/4- redox probe, higher maximum surface concentration of electroactive Mb (Gamma*max), and better electrocatalytic activity toward reduction of O2 and H2O2, mainly because of the good conductivity of Au nanoparticles. Because of the high biocompatibility of Au nanoparticles, adsorbed Mb in the films retained its near native structure and biocatalytic activity. The size effect of Au nanoparticles on the electrochemical and electrocatalytic activity of Mb in {Au/Mb}n films was investigated, demonstrating that the {Au/Mb}n films assembled with smaller-sized Au nanoparticles have smaller Rct, higher Gamma*max, and better biocatalytic reactivity than those with larger size.     

Use of CF3,Br/Al,discharges for reactive ion etching of III-V semiconductors

The reactive ion etching of GaAs, InP, InGaAs, and InAlAs in CF₃Br/Ar discharges was investigated as a function of both plasma power density (0.56-1.3 W - cm^–2) and total pressure (10-40 mTorr) The etch rate of GaAs in 19CF₃Br:1Ar discharges at 10 m Torr increases linearly with power density, from 600 Å min^–1 at 0.56 W · cm^–2, to 1550 Å · min at 1.3 W · cm^–2. The in-based materials show linear increases in etch rates only for power densities above – 1.0 W · cm^–2. These etch rates are comparable to those obtained with CCI₂F₂:O₂ mixtures under the same conditions. Smooth surface morphologies and vertical sidewalls are obtained over a wide range of plasma parameters. Reductions in the near-surface carrier concentration in n-type GaAs are evident for etching with power densities of >0.8 W cm^–2, due to the introduction of deep level trapping centers. At 1.3 W· cm^–2, the Schottky barrier height of TiPtAu contacts on GaAs is reduced from 0.74 to 0.53 eV as a result of this damage, and the photoluminescent intensity from the material is degraded. Alter RIE, we detect the presence of both F and Br on the surface of all of the semiconductors. This contamination is worse than with CCl₂F₂-based mixtures. High-power etching with CF₃Br/Ar together with Al-containing electrodes can lead to the presence of a substantial layer of aluminum oxide on the samples if the moisture content in the reactor is appreciable.     

Liposome-mediated enhancement of the sensitivity in immunoassay based on surface-enhanced Raman scattering at gold nanosphere array substrate

A novel immunoassay based on surface-enhanced Raman scattering (SERS) has been developed. The method exploits the SERS-derived signal from reporter molecules (crystal violet, CV) encapsulated in antibody-modified liposome particles. The antigen is firstly captured by the primary antibody immobilized in microwell plates and then sandwiched by secondary antibody-modified liposome. The CV molecules are released from the liposome and transferred to specially designed substrate of gold nanosphere arrays with sub-10-nm gaps. The concentration of the antigen is indirectly read out by the SERS intensity of the CVs. The substrate used could substantially improve the sensitivity and reproducibility of SERS measurement. The SERS intensity responses are linearly correlated to logarithm of antigen concentration in the range of 1.0 x 10(-8) to 1.0 x 10(-4) gm L(-1) with a detection limit of 8 ng mL(-1). To our knowledge, this is the first report describing liposome-mediated enhancement of the sensitivity in immunoassay based on surface-enhanced Raman scattering. Experimental results show that the proposed method illustrates a potential prospect of applications in immunoassay.     

Fabrication, characterization, and chemical etching of Ag nanoelectrodes

The previously developed methodologies for fabricating flat, polished nanoelectrodes were extended to produce silver electrodes with the radii from 50 nm to micrometers. The prepared electrodes were characterized by steady-state voltammetry, scanning electrochemical microscopy (SECM), and atomic force microscopy. The protocol was developed for controlled chemical etching of silver in ammonia solutions to produce recessed nanoelectrodes. Voltammograms and SECM approach curves were obtained to evaluate the recess depth and other geometric parameters of the etched electrodes.     

Planar array of 1D gold nanoparticles on ridge-and-valley structured carbon

For fabrication of a planar array of 1D chains of gold nanoparticles prepared by a chemical process, the faceted (110) planes of sodium chloride crystals were used as templates to produce nanoscale ridge-and-valley structured carbon layers by a vacuum process. When these carbon layers loaded on copper grids were dipped in toluene solution of 3.4 nm gold nanoparticles followed by natural dry, a planar array of 1D chains of gold nanoparticles were formed on carbon layers, where the nanoparticles were immobilized predominantly in valleys and partly on ridges of carbon layers.