电感耦合等离子体原子发射光谱法测定高温合金中低含量钇

建立电感耦合等离子体原子发射光谱法测定高温合金中低含量钇的方法。采用盐酸、硝酸、氢氟酸溶解样品,在优化的仪器条件下,采用基体匹配法配制系列标准工作溶液,选择分析线为360.073 nm。钇的含量在0.0005%~0.050%范围内与光谱强度具有良好的线性关系,相关系数为0.99999,检出限为0.000003%。该方法测定结果的相对标准偏差不大于6.0%(n=8),加标回收率为90.0%~104.0%。该方法简便、快速、准确,可用于高温合金中低含量钇的测定。     

电感耦合等离子体发射光谱法测定高纯铝中硅

建立电感耦合等离子体发射光谱(ICP-AES)法测定高纯铝中硅元素的分析方法。样品采用碱溶法进行预处理,以氢氧化钠溶液溶解,再加入盐酸、硝酸酸化。选取了硅251.611 nm分析谱线进行分析。硅的质量分数在0.001%~0.01%范围内与光谱强度具有良好的线性关系,线性相关系数为0.9991。该方法检出限为0.00012%,测定结果的相对标准偏差不大于10.2%(n=8),加标回收率为93.2%~104.2%。该方法操作简便,测定结果准确、可靠,适用于快速检测高纯铝中硅元素,具有推广价值。     

电感耦合等离子体发射光谱法测定二硼化锆中26种杂质

建立微波消解样品,电感耦合等离子体发射光谱法测定二硼化锆中26种杂质元素含量的方法。根据二硼化锆的化学组成对杂质检测的影响,确定了各元素最佳分析线;通过考察不同浓度的锆基体对待测元素的影响来确定最佳锆基体浓度;通过萃取法分离硼元素,消除硼对杂质检测的干扰;采用基体匹配法、多谱拟和技术消除了锆基体的干扰。在选定的仪器工作条件下,各待测元素的质量浓度与信号强度成良好的线性关系,线性相关系数均大于0.999。测定结果的相对标准偏差不大于6%(n=11),样品加标回收率为94%~101%。该方法操作简便,测定结果准确,可用于二硼化锆中26种杂质元素的测定。     

电感耦合等离子体原子发射光谱法测定钛合金中锆

建立电感耦合等离子体原子发射光谱法(ICP-AES)测定钛合金中锆元素的含量。采用盐酸-氢氟酸-硝酸溶解钛合金样品,选择357.247 nm为锆的分析谱线,通过基体匹配法消除基体钛的干扰,以电感耦合等离子体原子发射光谱法测定钛合金中锆的含量。锆的质量分数在0%~0.4%范围内与光谱强度呈良好的线性关系,相关系数大于0.999,定量下限为0.21%。测定结果的相对标准偏差小于2%(n=11),样品加标回收率为99.0%~102.7%。该方法快速、准确,能够满足实际生产中钛合金样品的测定要求。     

锌精矿中铟的测定

应用电感耦合等离子体发射光谱法测定锌精矿中的铟,确定了最佳工作条件,选择了最佳分析谱线,并利用标准加入法和基体匹配法确定了该方法的准确性。样品用氟化氢铵、盐酸、硝酸、高氯酸溶样,用盐酸浸取。本法与萃取分离盐酸羟胺示波极谱法测定的铟含量结果一致。方法准确,快速,加标回收率为99.6%~101.7%,相对标准偏差为0.97%~2.1%。     

电感耦合等离子体原子发射光谱法测定工业电解质中钙、镁、锂

工业电解质中微量元素钙、镁、锂对电解槽的正常运行非常重要。本文采用高氯酸加热挥发除氟,以盐酸(1 1)溶解残渣,选用Ca317.9nm、Mg297.5nm、Li670.7nm作为分析谱线,考察了样品处理方法、共存元素干扰对测定结果的影响。建立了电感耦合等离子体原子发射光谱法测定工业电解质中钙、镁、锂的方法。结果表明：不同的电解质因其所含氧化铝的不同会有部分不溶杂质,但对微量元素的测定影响很小,可以忽略不计。共存元素铝和钠不干扰微量元素的测定。按照试验方法对2个电解质标准样品进行了测定,其测定值与标准值吻合。同时对不同电解槽的工业电解质样品进行了分析,其结果的相对标准偏差(RSD,n=11)在0.69%-5.68%之间,满足生产分析的需要。     

电感耦合等离子体原子发射光谱(ICP-OES)法测定硫磺中的铅、铜、铁、镍、钙

提出了电感耦合等离子体原子原子发射光谱测定硫磺中的铅、铜、铁、镍、钙含量的方法,选择各元素的分析谱线,采用正交试验的方法确定仪器的工作参数,方法的检出限0.0046 ug/ml-0.012 ug/ml,方法的回收率在87.60%~111.78%,测定值的相对标准偏差(n=5)小于9.82%,填补无硫磺中铅、铜、镍、钙元素检测方法的空白。     

电感耦合等离子体发射光谱法检测镍基/钴基高温合金中硼磷硅

采用一定比例的混合酸溶解样品,利用基体匹配配制一系列标液消除基体的影响,以及轴向观测喷嘴吹扫技术来提高待测元素的灵敏度,使用电感耦合等离子体发射光谱(ICP-OES)测定镍基/钴基高温合金中硼磷硅。各元素选的分析线依次为B 182.577 nm、P 178.222 nm、Si 185.005 nm。检测范围分别是：B：0.001%-3.0%,P：0.003%-0.20%,Si：0.005%-3.0%,检出限范围是0.00005%-0.0004%,线性相关系数>0.9995。加标回收率为90.0%-105.0%,精密度RSD<2.0%。该方法操作简单快速,结果令人满意。     

电感耦合等离子体原子发射光谱(ICP-AES)法测定银钯合金中银和钯

建立健全测定银钯合金中银和钯含量的检测方法,对实现银钯合金中银和钯的高精度分析以及资源化利用有着重大意义。实验建立了电感耦合等离子发射光谱法(ICP-AES)同时测定银钯合金中银钯含量的分析方法。实验采用先加入10mL硝酸,再加入50mL过量盐酸混合,采用加热套混合消解银钯合金并混合定容在酸性浓度为18%HCl为介质中,然后通过控制不同的HCl浓度来测定银钯含量。实验结果表明：银的最佳检测酸性浓度为18%、钯的最佳酸性检测浓度为4%且该方法的加标回收率在97%-100%之间,相对标准偏差(RSD, n=10)小于2%。     

电感耦合等离子体发射光谱法（ICP-OES）测定钴白合金中锗

建立了一种电感耦合等离子体发射光谱法（ICP-OES）测定钴白合金中锗含量的分析方法,确定了最佳实验条件,方法的检出限为0.043 μg/mL,对钴白合金中锗的测定结果与其他法结果一致,方法的相对标准偏差RSD在1.07 %~1.91 %（n=7）之间,样品的加标回收率在98.5 %~102.1 %之间。     

ICP-AES 法测定硅铁中痕量元素

采用电感耦合等离子原子发射光谱法测定硅铁中的痕量元素,研究了 Fe 基体对被测元素的影响,并选择了最佳工作条件.被测元素的检测限为 0 .60～76.2 ng/mL,样品加标回收率为 92%～108%,RSD(n=8)<3%.     

Laser ablation inductively coupled plasma atomic emission spectrometry of a uranium-zirconium alloy: ablation properties and analytical behavior

The ablation properties and analytical behavior of a uranium-zirconium alloy have been examined using tandem laser ablation/pneumatic nebulization sample introduction in conjunction with inductively coupled atomic emission spectrometry (LA-ICP-AES). An apparent change in composition of the laser ablation aerosol (1–15 GW cm⁻² Zr deficient, 40–250 GW cm⁻² Zr rich) is observed. This phenomenon is independent of laser wavelength. After collection and bulk chemical analysis of the ablation product, this phenomenon is attributed to an atomization interference in the ICP.

Two distinct modes of laser ablation have been observed which depend upon the wavelength of the ablating laser (visible or near infrared). These two modes result in characteristic ablation crater types and analyte emission behavior. Ablation yields at 1064 nm are dependent upon laser power density only, whilst yields at 532 nm are dependent upon both laser power density and illumination area. The latter is considered to be symptomatic of direct interaction of the laser light with the surface, and the former, of indirect coupling of laser energy, via a micro-plasma, into the surface.     

电感耦合等离子体原子发射光谱法测定新购及再生铬矿砂中二氧化硅

新及再生铬矿砂经1000℃灼烧,研磨,以过氧化钠为熔剂,经高温熔融,热水洗涤,盐酸、硝酸酸化前处理样品,直接用电感耦合等离子体发射光谱法测定铬矿砂中的二氧化硅。试验了熔融试样时引入的基体元素钠对被测元素的干扰情况,结果表明,过氧化钠加入为1.5克对检测干扰影响小。采用加基体铬、铁有效克服了基体效应对结果影响。硅的检出限为0.0049 mg/L, 二氧化硅测定范围为0.010%～6.0%。对铬矿砂标准物质进行测定,结果与标准值一致,方法精密度(RSD,n=10)小于1%。常规重量方法步骤繁琐、耗时长、工作量大的不足。本检测方法大大提高了检测效率,满足生产需要。     

电感耦合等离子体原子发射光谱法测定稀土钢中微量镧、铈

采用稀王水溶解样品,选择La408.672 nm、Ce456.236nm为分析线,建立了电感耦合等离子体原子发射光谱法(ICP-OES)测定稀土钢中微量镧、铈的方法。结果表明,各元素校准曲线线性良好,相关系数可达0.99999;方法测定范围为：0.0001%～0.10%。检出限为：镧0.00002%,铈0.00006%。按照实验方法测定标样中镧、铈,结果的相对标准偏差RSD(n=8)为2.18%、1.68%。     

Separate vaporisation of boric acid and inorganic boron from tungsten sample cuvette-tungsten boat furnace followed by the detection of boron species by inductively coupled plasma mass spectrometry and atomic emission spectrometry (ICP-MS and ICP-AES)

Utilising extremely different vaporisation properties of boron compounds, the determination procedures of volatile boric acid and total boron using tungsten boat furnace (TBF) ICP-MS and TBF-ICP-AES have been investigated. For the determination of volatile boric acid by TBF-ICP-MS, tetramethylammonium hydroxide (TMAH, Me₄NOH) was used as a chemical modifier to retain it during drying and ashing stages. As for the total boron, not only non-volatile inorganic boron such as boron nitride (BN), boron carbide (B₄C), etc. but also boric acid (B(OH)₃) was decomposed by a furnace-fusion digestion with NaOH to produce sodium salt of boron, a suitable species for the electrothermal vaporisation (ETV) procedure. The proposed method was applied to the analysis of various standard reference materials. The analytical results for various biological and steel samples are described.     

Application of wavelet transform to background correction in inductively coupled plasma atomic emission spectrometry

A background correction method based on wavelet transform was devised and applied to inductively coupled plasma atomic emission spectrometry (ICP-AES). The proposed approach separated background from analyte signal according to their different frequencies. Compared with the analyte signal, the background has a low frequency. By removal of the components attributed to the signal, the background over the spectral window of the analyte line can be fitted through wavelet reconstruction. The results showed that the wavelet transform technique could handle all kinds of background and low signal-to-background ratio spectra, and required no prior knowledge about the sample composition, no selection of suitable background correction points, and no mathematical assumption of the background distribution. This technique performed as well as the conventional three-point background correction method for linear backgrounds, and provided better results than the latter for curved backgrounds. The proposed procedure was illustrated, by processing real spectra, to be an effective and practical tool for background correction in ICP-AES.     

Silicon determination by inductively coupled plasma atomic emission spectrometry after generation of volatile silicon tetrafluoride

A method for the determination of silicon by inductively coupled plasma atomic emission spectrometry (ICP-AES) is described. The procedure is based on a discontinuous generation of volatile silicon tetrafluoride in concentrated sulphuric acid medium after injecting 125 μl of 0.1%, w/v sodium fluoride solution into 100 μl of the sample. The gaseous silicon tetrafluoride is fed directly into the ICP torch by a flow of 250 ml min⁻¹ Ar carrier gas. The calibration curve was linear up to at least 100 μg ml⁻¹ of Si(IV) and the absolute detection limit was 9.8 ng working with a solution volume of 100 μl. The relative standard deviation for six measurements of 10 μg ml⁻¹ of Si(IV) was 2.32%. The method was applied to the determination of silicon in water and iron ores.     

电感耦合等离子体原子发射光谱法（ICP-AES）测定RoHS指令聚合物中的铅和镉

本文引入微波技术消解聚合物塑料样品,使用电感耦合等离子体原子发射光谱仪（ICP-AES）测定聚合物中的铅（Pb）和镉（Cd）含量,并建立了优化的样品消解程序和测定方法,得到满意的测定结果。[摘要应包括目的、方法、结果、结论,请修改,同时修改英文]该方法具有效率高、污染小的优点。检测结果具有良好的精密度。     

Determination of trace impurities in boron nitride by graphite furnace atomic absorption spectrometry and electrothermal vaporization inductively coupled plasma optical emission spectrometry using solid sampling

Two digestion-free methods for trace analysis of boron nitride based on graphite furnace atomic absorption spectrometry (GFAAS) and electrothermal vaporization inductively coupled plasma spectrometry optical emission (ETV-ICP-OES) using direct solid sampling have been developed and applied to the determination of Al, Ca, Cr, Cu, Fe, Mg, Mn, Si, Ti and Zr in four boron nitride materials in concentration intervals of 1–23, 54–735, 0.05–21, 0.005–1.3, 1.6–112, 4.5–20, 0.03–1.8, 6–46, 38–170 and 0.4–2.3 μg g^− 1, respectively. At optimized experimental conditions, with both methods, effective in-situ analyte/matrix separation was achieved and calibration could be performed using calibration curves measured with aqueous standard solutions. In solid sampling GFAAS, before sampling, the platform was covered with graphite powder and, for determination of Si, also the Pd/Mg(NO₃)₂ modifier was used. In the determination of all analyte elements by solid sampling ETV-ICP-OES, Freon R12 was added to argon carrier gas. For solid sampling GFAAS and ETV-ICP-OES, the achievable limits of detection were within 5 (Cu)–130 (Si) ng g^− 1 and 8 (Cu)–200 (Si) ng g^− 1, respectively. The results obtained by these two methods for four boron nitride materials of different purity grades are compared each with the other and with those obtained in analysis of digests by ICP-OES. The performance of the two solid sampling methods is compared and discussed.     

Direct analysis of fly ash materials by inductively coupled plasma atomic emission spectrometry using slurry nebulization

Fly ash samples of cement works were analysed using slurry nebulization inductively coupled plasma atomic emission spectrometric (ICP-AES). Because of the influence of the experimental factors on the signal intensity, the optimal conditions of the analysis circumstances were determined. Control analyses (wet digestion followed by ICP-AES, and XRF of dry powders (pressed pellets)) were also carried out to compare the results. Based on the result, it was concluded that the slurry nebulization method using slurry standard of same type reference material for calibration can be applied for rapid but less precise (RSD 5–10%) determination of the elements in fly ash.