Synthesis and electrochemical properties of chemically substituted LiMn2O4 prepared by a solution-based gel method

Lithium manganese oxide, LiMn(2)O(4), and its substituted samples LiM(0.05)Mn(1.95)O(4) (M=Al, Co, and Zn) were first prepared by a cost-saving and effective new solution-based gel method using a mixture of acetate and ethanol as the chelating agent. The physical properties of the synthesized samples were investigated by thermogravimetry/differential thermal analysis, X-ray diffraction, and scanning electronic microscopy. The as-prepared powders were used as positive materials for a lithium-ion battery, whose charge/discharge properties and cycle performance were examined. The results revealed that all the substituted samples had better cycle performance than pure LiMn(2)O(4). Among these synthesized materials, the LiCo(0.05)Mn(1.95)O(4) sample had the best cycle performance. After 30 cycles, its capacity loss was only 3%. Therefore, cyclic voltammetry and electrochemical impedance spectroscopy were employed to characterize the reactions of Li ion insertion into and extraction from LiCo(0.05)Mn(1.95)O(4) electrodes.     

Synthesis of ZnO/polystyrene composites particles by Pickering emulsion polymerization

ZnO/polystyrene composite particles were synthesized by Pickering emulsion polymerization. ZnO nanoparticles were first prepared by reaction of zinc acetate and sodium hydroxide in ethanol medium. Then different amount of styrene monomer was emulsified in water in the presence of ZnO nanoparticles either by mechanical stirring or by sonication, followed by polymerization of styrene. Two kinds of initiators were used to start the polymerization, azobisisobutyronitrile (AIBN) and potassium persulfate (KPS). The X-ray diffraction pattern verified the crystal structure of ZnO and FT-IR spectra evidenced the existence of ZnO and polystyrene (PS) in ZnO/polystyrene composite particles. Different morphologies were observed for the composite particles when using different initiators. From TEM photographs, AIBN-initiated system produced mainly core-shell composite particles with PS as core and ZnO as shell, while KPS-initiated system showed both composite particles and pure PS particles. Two schemes of reaction mechanism were proposed to explain the morphologies accordingly. Both systems of composite particles showed good pH adjusting ability.     

Synthesis of molybdenum disulfide particles by aerosol-assisted chemical vapor deposition

It was shown that dimethylformamide can be, in principle, used as a solvent of ammonium thiomolybdate for obtaining molybdenum disulfide particles by the aerosol-assisted chemical vapor deposition method. IR Fourier spectroscopy was used to examine (NH₄)₂MoS₄–C₃H₇NO liquid solutions and the thermal stability of dimethylformamide and ammonium thiomolybdate vapors. It was demonstrated that pyrolysis at temperatures of 700–900°C yields spherical molybdenum disulfide microparticles with average diameters in the range 0.6–1 µm and “onion” structure.     

Synthesis of aligned ZnO nanocolumn arrays by a vapor phase transport method

Vertically large-scale aligned ZnO nanocolumn arrays have been synthesized on Si(100) substrate at 550°C via a simple vapor phase transport process in a horizontal chemical vapor depositon (CVD) reactor. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) observations show that the ZnO nanocolumns have a uniform length of about 3 ??m with an average diameter of 80 nm. The clear lattice fringes in HRTEM image indicate the synthesis of good quality hexagonal single crystal ZnO. The X-ray diffraction (XRD) result shows the nanocolumns are c-axis preferentially oriented.     

Synthesis and evolution of novel double tower-like ZnO by a simple method

Delicate double tower-like ZnO have been fabricated through the decomposition of the zinc nitrate hexahydrate (Zn(NO₃)₂6H₂O). The phase transformation and morphology evolution of the products were carefully studied and investigated with X-ray diffraction, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, and Raman spectra. The resultant results indicated that the obtained double tower-like ZnO materials possess pure wurtzite hexagonal phase, growing along the [100] direction. A reasonable formation mechanism was also presented in this paper.     

Preparation, structure and ultraviolet photoluminescence of ZnO films by a novel chemical method

A novel and simple chemical method was developed for the deposition of ZnO films from aqueous solution, integrating the merits of successive ionic layer adsorption and reaction with the chemical bath deposition technology. By this new method, dense and continuous ZnO thin films with good crystallinity can be prepared in a very short time, e.g., in about 20 min. Results show that as-deposited ZnO films on glass and Si (1 0 0) exhibit hexagonal wurtzite crystalline structure and the preferential orientation along (0 0 2) plane. With a dense and continuous appearance, the film is composed of ZnO particles in even size of 200-300 nm. The strong and sharp emission at 391 nm and several weak emissions at the wavelength band of 440-500 nm indicate the high optical quality and the stoichiometrical nature of obtained film. Mechanism analysis shows that the reaction duration in hot water and the drying process are vital important factors affecting the deposition process and the crystallization behavior of the film prepared via the aqueous solution route.     

A facile method to prepare CdS/polystyrene composite particles

Nano-CdS/polystyrene composite particles were prepared via surfactant-free emulsion polymerization. 2-(Dimethylamino)ethyl methacrylate (DMEMA) was used as auxiliary monomer which co-polymerized with styrene (St) and provided the location for coordinating with Cd²⁺. By the coordination of Cd²⁺ ions to DMEMA, mono-disperse polystyrene with the Cd²⁺ ions on the particles surface were prepared successfully. With the release of S²⁻ ions from the thioacetamide (TAA), cadmium sulfide (CdS) was formed. Nano-CdS/PS composite particles could be synthesized via this facile method. The order of materials addition and the amount of initiator both are playing important roles to the final morphologies of the composite particles. In the method proposed in this study, no surfactant was used, and the stable emulsion was successfully obtained. UV–vis absorption and fluorescence measurement indicated the quantum dot effect in the resulted nano-CdS/PS composite particles. The possible composite particle formation mechanism was presented.     

Facile chemical approach to ZnO submicrometer particles with controllable morphologies

We have developed a simple wet-chemistry approach to fabricating ZnO submicrometer particles with unique morphologies including rings, bowls, hemispheres, and disks. The size and morphology of the particles can be conveniently tailored by varying the concentrations of the zinc precursor. The reaction temperature, pH, and concentration of ammonia are also found to play critical roles in directing the formation of these particle morphologies. These submicrometer particles exhibit strong white-light emission upon UV excitation as a result of the presence of surface defect states resulting from the fabrication method and synthesis conditions.     

Synthesis of amino‐functionalized latex particles by a multistep method

Cationic latex particles with surface amino groups were prepared by a multistep batch emulsion polymerization. In the first one or two steps, monodisperse cationic latex particles to be used as the seed were synthesized, and in the third step, two different amino‐functionalized monomers [aminoethylmethacrylate hydrochloride (AEMH) and vinylbenzylamine hydrochloride (VBAH)] were used to synthesize the final functionalized latex particles. 2,2′‐Azobisisobutyramidine dihydrochloride was used as the initiator, and different concentrations of two quaternary ammonium emulsifiers with hydrophobic chains of different lengths were examined. To characterize the final latexes yields were obtained gravimetrically, and particle size distributions and average particle diameters were determined by transmission electron microscopy and photon correlation spectroscopy. The amount of amino groups was determined by fluorimetry. The effect of the amino‐functional monomer used on the final latexes and the colloidal behavior of the system were studied. The influence of the different conditions utilized to synthesize the latexes on the colloidal stability of the particles was evaluated in terms of the Fuchs stability ratio and electrophoretic mobility. High yields of the amino‐functional monomers were obtained. Surface amino, amidine, and quaternary ammonium groups provided the cationic character. The colloidal stability behavior of the products obtained was compatible with their cationic character. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2929–2936, 2001     

Synthesis and morphological characterization of nanocrystalline powders obtained by a gas condensation method

The preparation of nanocrystalline powders of Fe and Fe50Ni50 has been performed by a gas-condensation method under pure helium atmosphere. The characterization of the prepared materials which was carried out by means of Transmission Electron Microscopy, X-rays diffraction and Mössbauer Spectrometry, evidences for the presence of oxide phases. Fe and FeNi based ultrafine particles are observed with a size comprised within the range 10–70 nm and they occur as clusters or chains.     

Synthesis of a novel water-soluble polyamide dendrimer based on a facile convergent method

A novel, rapid, inexpensive, and highly efficient convergent approach has been developed for the synthesis of a 32-amine-terminated G3 polyamide dendrimer by the hydrolysis of the dendrimer with trifluoroacetamide groups. The resulting dendrimer could be successfully modified with oligo(ethylene glycol) chains at its periphery to afford a novel water-soluble polyamide dendrimer. The structural homogeneity of the dendrimers was confirmed by NMR and MALDI-TOF mass spectroscopies.     

Photocatalytic studies of silver doped ZnO nanoparticles synthesized by chemical precipitation method

Ag-doped ZnO nanoparticles (Zn_1?xAg_xO; where x = 0.00–0.05) were synthesized by chemical precipitation method. The synthesized products were characterized by X-ray diffraction, scanning electron microscope (SEM), transmission electron microscope (TEM) and UV–Vis spectrometer. The SEM and TEM micrographs revealed the agglomerated spherical-like morphology and the measurements show that the size of crystallites is in the range of 10–40 nm. Optical measurements indicated a red shift in the absorption band edge after Ag doping. The band gap values of as prepared undoped and doped with silver samples were found to decrease with increase in temperature from 300 to 800 °C. Photocatalytic activities of ZnO and Ag doped ZnO were evaluated by irradiating the sample solution to ultraviolet light by taking methylene blue as organic dye. The experiment demonstrated that the photo-degradation efficiency of 1 mol% Ag-doped ZnO was significantly higher than that of undoped and 2–5 mol% Ag doped ZnO under ultraviolet light irradiation.     

A facile two-step etching method to fabricate porous hollow silica particles

We report here the fabrication of hollow silica particles with mesopores larger than 10 nm on their wall via a facile two-step etching method. Different from the conventional template method, the new method uses the silica particles as starting materials, which were synthesized using the well-known Stöber method. In the hollow silica preparation, first, we gently etch the silica particles with a NaOH solution without using template molecules to make them porous. Then, we coat the porous silica particles with poly-dimethyldiallylammonium chloride (PDDA) and treat the PDDA-coated porous silica with an ammonia solution to form the hollow silica nanospheres. In this study, we found that the NaOH dosage and ammonia concentration have significant impact on the morphology of the final products. Adsorption was also studied and results show that the hollow nanospheres can effectively uptake protein-based biomolecules (hemoglobin).     

Synthesis of nanosized chitosan-poly(acrylic acid) particles by a dropping method

Deoxyribonucleic acid (DNA) vaccines are being investigated extensively because of their excellent potential over conventional protein ones. A suitable DNA carrier, consisting of uniformly dispersed chitosan-poly(acrylic acid) particles with an average size of 30 nm, was successfully synthesized by a dropping method with a ratio of chitosan solution to poly(acrylic acid) solution of 1:1 and was incubated in a buffer solution with a pH value of 3.0. The particle size increased from 35.76 to 45.90 nm when the pH value of the buffer solution was increased from 3.0 to 7.4. After freeze-drying, the non-incubated mixed solution showed a membranous morphology. A powdered product was formed from the mixed solution as incubated in buffer solution with pH values of 3.0 and 5.3. However, when the mixed solution was incubated in a buffer solution of pH 7.4, a mixture of membrane and powder was obtained.     

Highly efficient photocatalytic performance of dye-sensitized K-doped ZnO nanotapers synthesized by a facile one-step electrochemical method for quantitative hydrogen generation

Journal of Solid State Electrochemistry - The different morphologies of K-doped ZnO nanostructures were successfully synthesized by a facile one-step electrochemical method using control of the...     

A facile method to fabricate ZnO hollow spheres and their photocatalytic property

This paper presents a novel and facile method for the fabrication of ZnO hollow spheres. In this approach, zinc ions were first adsorbed onto the surfaces of sulfonated polystyrene core-shell template spheres, and then reacted with NaOH to form a ZnO crystal nucleus, which was followed by a growth step to form ZnO nanoshells. During the formation of ZnO nanoshells or later on, the template spheres were "dissolved" in the same media to obtain ZnO hollow spheres directly. Neither additional dissolution nor calcination process was needed in this method to remove the templates, and the reaction conditions were very mild: neither high temperature nor long time was needed. Transmission electron microscopy, scanning electron microscopy, X-ray photoelectron spectroscopy, X-ray diffraction, and Brunauer-Emmett-Teller analysis were used to investigate the morphology, surface composition, crystalline structure, specific surface area, and porosity of the ZnO hollow spheres, respectively. UV-visible spectra show that these ZnO hollow spheres had very good photocatalytic activity.     

Synthesis of ZnO:Ga nanosized powders by the combustion method

The synthesis of ZnO:Ga(0.075 wt%) nanosized powders via combustion reaction at 145°C and subsequent calcination of the ground combustion product at 500–900°C was studied. Zinc and gallium nitrates were used as initial substances, and sucrose, as fuel. It was found that Ga₂O₃ nanoparticles are located on the ZnO particles and inhibit their growth.     

Polymeric vesicle permeability: a facile chemical assay

We present a simple method to characterize vesicles and determine, at the same time, the membrane permeability to specific molecules. The method is based on encapsulating highly hydrophilic 3,3',3' '-phosphinidynetris-benzenesulfonic acid (PH) into vesicles and subsequently monitoring its reaction with 5,5'-dithiobis-2-nitrobenzoic acid (DTNB). We tested the method by measuring the membrane permeability of vesicles formed from a series of poly(ethylene oxide)-co-polybutylene oxide (EB) copolymers and egg yolk phosphatidylcholine. We found that the experimental data are in good agreement with calculations based on Fick's first law. We therefore quantified the DTNB permeability across vesicle membranes, finding that polymeric EB membranes have a more selective permeability toward polar molecules compared to phospholipids membranes.