甲基取代对聚吡咯结构和性能的影响

本文采用量化学ＳＣＦ－ＭＮＤＯ和ＣＮＤＯ／２－ＣＯ方法对三种聚甲基取代吡咯的结构进行优化，分析了它们的电子能带结构，探讨了甲基取代对聚吡咯结构和性能的影响。     

成膜溶剂对聚4-甲基戊烯-1膜形态结构及渗透汽化特性的影响

以聚4－甲基戊烯－1（PMP）为膜材质、分别以环己烷、三氯乙烯以及环己烷／三氯乙烯为溶剂，以浇铸法制备了PMP的均质致密膜。研究了不同溶剂体系的相对溶解能力和挥发速度对PMP膜结晶度和形态结构的影响，并对成膜的渗透汽化特性的影响进行了研究。     

成膜溶剂对聚4-甲基戊烯-1膜的形态结构和透过行为的影响——Ⅱ.膜的气体透过行为

以聚4－甲基戊烯－1（PMP）为膜材质，分别以环己烷、三氯乙烯、四氯乙烯及环己烷／三氯乙烯为溶剂，研究了这些溶液浇铸膜对O2、N2、H2及CO2等气体的透过行为。结果表明，气体的透过主要发生在PMP的无定形区域，但也在PMP的晶区进行。PMP的Ⅵ型结晶比Ⅰ型结晶具有较低的氧化透过活化能。     

聚磷酸酯的合成及其释药性能研究

以三异丁基铝为引发剂研究了２－氢－２－氧－１，３，２－二氧五环磷酸酯的开环聚合反应。聚合产物经氯化、水解，获得了一种新型的交联聚磷酸酯。用交联聚磷酸酯为载体，采用单植片和夹心片的方法式，对左旋－１８－甲基炔诺酮进行了控制释放研究。     

1,3,3-三甲基-2-亚甲基吲哚啉合成新工艺

报道了一种以N－甲基苯肼和3－甲基－2－丁酮为原料一步合成1，3，3－三甲基－2－亚甲基吲哚啉的新工艺。讨论了影响产品收率的各种因素。该新工艺具有原料易得，工艺路线较短，减少环境污染等特点。     

一些交联聚甲基丙烯酸甲酯材料的热裂—解色—谱质谱分析

本文对５个交联的聚甲基丙烯酸甲酯进行热裂解－色谱－质谱分析研究。裂解温度３７０℃，用ＯＶ－１石英毛细管柱分离，鉴定了交联聚甲基丙烯酸甲酯中少量的共聚单体和助交联剂：甲基丙烯酰胺、氰脲酸三烯丙酯、二甲基丙烯酸－缩二乙二醇酯和二甲基丙烯酸新戊二醇酯。     

N－丙烯酰基－N＇－苯基脲及其衍生物的合成与聚合反应

以三种合成路线分别合成了含有脲键的一类单体，Ｎ－丙烯酰基－Ｎ’－苯基脲（ＡＰＵ）、Ｎ－甲基丙烯酰基－Ｎ’－苯基脲（ＭＰＵ）、Ｎ－甲基丙．烯酰基－Ｎ’－对甲苯基脲（ＭＴＵ），通过单体的自由基聚合与共聚合，制备了均聚物和共聚物，经ＩＲ、１Ｈ—ＮＭＲ表征和ＴＧＡ、ＤＳＣ测定．     

聚1-甲基-2-吡咯烷酮修饰碘离子化学传感器的研究

研究了１－甲基－２－吡咯烷酮在玻碳（ＧＣ）电极表面聚合的条件，测试了Ｉ－－聚１－甲基－２－吡咯烷酮化学传感器的电化学性能。所制电极检测Ｉ－响应线性范围２４×１０－４～０１ｍｏｌ／Ｌ，检测下限为１０×１０－４ｍｏｌ／Ｌ，电极的重现性及稳定性都较好，重复测定７次相对标准偏差为０７１％，可连续使用２５天。Ｃｌ－、Ｂｒ－、ＮＯ－３、ＳＯ２－４等阴离子对测定干扰较小     

成膜溶剂对聚4-甲基戊烯-1膜的形态结构和透过行为的影响——Ⅰ.膜的结晶性质与表面形态

以聚4－甲基戊烯－1（PMP）为膜材质，分别以环己烷、三氯乙烯、四氯乙烯、环己烷／三氯乙烯及环己烷／四氯乙烯为溶,他这些溶液浇铸膜垢结晶性质和表面形态。结果表明，溶剂对PMP的相对溶解能力和挥发速度同所成膜内PMP的结晶形式和结晶度密切相关；不同溶剂体系的PMP溶液浇铸膜的表面形态也不尽相同。并发现以四氯乙烯（或三氯乙烯）为溶剂或溶剂组分之一的PMP溶液浇铸膜存在未见报道的Ⅵ型结晶。     

聚1-三甲基硅基丙炔膜渗透汽化分离乙醇-水溶液的研究Ⅰ.PTMSP膜渗透汽化分离乙醇-水传质的基本特征

研究了聚１－三甲基硅基丙炔膜渗透汽化分离乙醇－水溶液传质的主要特点。发现膜对乙醇优先吸附、溶解，对水优先扩散。但因吸附液中水含量很低，总的结果表现为优先透醇。在３１３Ｋ，膜厚２０～２５μｍ，料液浓度１０ｗｔ％时，α＝１８．５，Ｊ＝０．９６９ｋｇ·ｍ－２·ｈ－１。透过膜的渗透液及其中的水和乙醇渗透汽化表观活化能分别为２８．８７、３１．３０和２７．６６ｋＪ／ｍｏｌ，并随料液浓度下降而增加。对实验数据进行非线性回归，建立了该膜传递乙醇的经验关联式：Ｊｅ＝－５．５６４Ｃ２Ｅ０＋１３．３４ＣＥ０－０．１５７３（ｋｇ·ｍ－２·ｈ－１），计算值与实验值相吻合。     

Micellization and Thermogelation of Poly(ether urethane)s Comprising Poly(ethylene glycol) and Poly(propylene glycol)

A series of multiblock poly(ether urethane)s comprising poly(ethylene glycol) (PEG), and poly(propylene glycol) (PPG) segments were synthesized. Their aqueous solutions exhibited thermogelling behavior at critical gelation concentrations (CGC) ranging from 8 to 12 wt%. The composition and structural information of the copolymers were studied by GPC and ¹H NMR. The critical micellization concentration (CMC) and thermodynamic parameters for micelle formation were determined at different temperatures. The temperature response of the copolymer solutions were studied and found to be associated with the composition of the copolymers.     

聚L-丙氨酸-聚乙二醇嵌段共聚物的胶束化行为研究

以氨基聚乙二醇单甲醚(MPEG-NH₂)为大分子引发剂, 采用开环聚合方法合成了聚L-丙氨酸-聚乙二醇嵌段共聚物(PAME), 并对其结构进行了表征; 用圆二色谱(CD)研究了嵌段共聚物在水溶液中的二级结构, 用芘荧光探针技术研究了共聚物胶束的形成及其临界胶束浓度(CMC), 利用动态光散射(DLS)和透射电镜(TEM)研究了胶束的粒径分布和形态. 结果表明, 在水溶液中共聚物链以α-螺旋构象形式存在, 在一定条件下嵌段共聚物能够形成球形的稳定胶束, PAME-1形成胶束的CMC为1.99×10^-5 mol/L, CMC值受共聚物中聚L-丙氨酸(PLA)链段含量的影响.     

聚癸二酸丙三醇酯对聚乳酸的改性

以丙三醇和癸二酸为单体通过熔融缩聚制得了聚癸二酸丙三醇酯(PGS),并用其预聚物(p-PGS)对聚L-丙交酯(PLLA)进行共混改性.利用傅立叶变换红外光谱(FT-IR)、核磁共振氢谱(1H-NMR)及凝胶渗透色谱(GPC)法对P-PGS的结构进行表征,并研究了改性后材料的力学性能、两相相容性、亲水性能和细胞相容性.结果表明:P-PGS具有支化分子结构,分散系数约为2.7;共混改性后的材料弹性模量和拉伸强度均有所下降,而断裂伸长率从7 %显著提高到150%左右;PLLA/PGS属于海岛式共混结构,PGS以小于10μm的尺寸均匀分布在PLLA基体中;共混后材料的亲水性也有一定的提高,且几乎保持了PLLA原有的细胞相容性.     

Poly(dialkoxyethyl itaconates)

The oxidative and non-oxidative degradation of poly(di-methoxy-), poly(di-ethoxy-), poly(di-iso-propoxy-) and poly(di-n-butoxyethyl itaconate) were investigated by thermogravimetry. Characteristic degradation temperatures and apparent activation energies of degradation were determined for the non-oxidative degradation of all the investigated polymers. It was not possible to determine these characteristics in the presence of oxygen as the degradation was accompanied by a secondary exothermic reaction. Based on examination of the monomers, it is supposed that the exothermic reaction is a repolymerisation of the monomers released during the earlier stages of polymer degradation.     

制备聚(L-乳酸-co-乙醇酸）/聚D-乳酸共混物立构复合物的新方法

首次以高分子量的聚(L-乳酸-co-乙醇酸）(PLLGA）和D-聚乳酸（PDLA)［m(PLLGA) : m(PDLA)=3:1, c 50 mL·g^-1］为原料,氯仿为溶剂,等体积的甲醇为沉淀剂,于50 ℃蒸发4 h形成了PLLGA和PDLA的立构复合物（sc-PLA）,其结构和性能经XRD, DSC和TGA表征。结果表明：sc-PLA的结晶度达96.2%,热失重5%温度为342 ℃（PLLGA为304 ℃）。     

Poly(phenylenediamine) Dispersions

The formation and properties of poly(phenylenediamine) colloidal dispersions were investigated. Oxidative dispersion polymerization of 1,3-phenylenediamine dihydrochloride stabilized with poly(N-vinylpyrrolidone) was taken as a reference experiment. Conductivity, temperature, and acidity of the reaction mixture were recorded during the polymerization. Oxidations of all three phenylenediamine bases, of corresponding dihydrochlorides, and of dihydrochlorides in excess acid are compared. The effect of the nature of steric stabilizer on the course of polymerization was found to be marginal. Dispersion polymerization was observed to proceed faster than the precipitation one. Dynamic light scattering was used to assess particle sizes in poly(phenylenediamine) dispersions. The results are discussed in relation to an analogous polymerization of aniline leading to polyaniline dispersions. Copyright 2001 Academic Press.     

两亲型聚L-亮氨酸-聚乙二醇单甲醚嵌段共聚物的合成与表征

开环聚合;生物降解共聚物;两亲型聚L-亮氨酸-聚乙二醇单甲醚嵌段共聚物的合成与表征     

环氧丙烷聚醚三元醇/聚乳酸嵌段共聚物的合成与性能

以低不饱和度环氧丙烷聚醚三元醇与L型及DL型丙交酯为原料, 合成了不同单体物质的量比的聚醚与聚乳酸嵌段共聚物. 采用FTIR, 1H NMR, GPC对共聚物的结构进行了表征; 用DSC, DTA对共聚物的玻璃化转变温度、熔点及热分解温度进行了研究. 结果表明, 丙交酯在聚醚多元醇端羟基的引发下发生开环反应, 得到聚环氧丙烷L型乳酸(POLLA)或聚环氧丙烷DL型乳酸(PODLA)二嵌段共聚物. POLLA二嵌段共聚物具有结晶能力, 且随着L型聚乳酸链段的增长而增强. PODLA二嵌段共聚物为非晶态聚合物. 两种共聚物的玻璃化转变温度与共聚物的组成有关, 其值介于聚醚和聚乳酸玻璃化转变温度之间. 与聚醚三元醇相比, 二嵌段共聚物的耐热性得到提高, 其热分解温度提高了30～60 ℃, 约为235～262 ℃. 共聚物的结构和组成对材料的热降解机制有很大影响. PODLA在高温区发生热氧化降解.     

Poly(Urethane)-Crosslinked Poly(HEMA) Hydrogels

Abstract

Hydrogels have been prepared from 2-hydroxyethyl methacrylate polymerized in the presence of isocyanate-terminated poly(ethylene glycol) (PEG) crosslinking agents. PEGS of molecular weights 200, 400, and 1000 were investigated. The crosslinked nature of the hydrogels was demonstrated by their insolubility in solvents which normally dissolve poly(HEMA). Hexamethylene diisocyanate (HDI) was mainly used as the isocyanate. The molecular weight of the PEG and the crosslinker content significantly influenced the equilibrium water sorption and mechanical properties of the saturated networks. It was observed that as the molecular weight of the PEG increased, the water sorption increased and the nominal modulus decreased. However, for higher levels of cross-linker, water sorption decreased and modulus increased at low molecular weight PEG; for PEG 1000, water absorption increased as crosslinker content increased. These results are explained by the competing effects of flexibility, crosslink density, and hydrophobicity contributed by the various constituents of the hydrogels.     

Modification of Poly(Ethylene Terephthalate) Track Membranes by Sorption of Poly(Ethylene Glycol)

Sorption of poly(ethylene glycol) on poly(ethylene terephthalate) track membranes was studied at different pH. The hydrophilic-hydrophobic properties of the intact membranes and those modified with poly(ethylene glycol) are compared. The membrane-aqueous human serum albumin and membrane-aqueous insulin adhesive tensions were determined for modified membranes. The competitive sorption of human serum albumin and poly(ethylene glycol) from aqueous solution on the track membranes is analyzed.