Nonisothermal cold crystallization behavior and kinetics of polylactide/clay nanocomposites

The nonisothermal cold crystallization behavior of intercalated polylactide (PLA)/clay nanocomposites (PLACNs) was studied using differential scanning calorimetry, polarized optical microscope, X‐ray diffractometer, dynamic mechanical thermal analysis, and Fourier transform infrared spectrometer. The results show that both the cold crystallization temperature (T_cc) and melting point (T_m) of PLA matrix decreases monotonously with increasing of clay loadings, accompanied by the decreasing degree of crystallinity (X_c%) at the low heating rates (≤5 °C/min). However, the X_c% of PLACNs presents a remarkable increase at the high heating rate of 10 °C/min in contrast to that of neat PLA. The crystallization kinetics was then analyzed by the Avrami, Jezioney, Ozawa, Mo, Kissinger and Lauritzen–Hoffman kinetic models. It can be concluded that at the low heating rate, the cold crystallization of both the neat PLA and nanocomposites proceeds by regime III kinetics. The nucleation effect of clay promote the crystallization to some extent, while the impeding effect of clay results in the decrease of crystallization rate with increasing of clay loadings. At the high heating rate of 10 °C/min, crystallization proceeds mainly by regime II kinetics. Thus, the formation of much more incomplete crystals in the PLACNs with high clay loadings due to the dominant multiple nucleations mechanism in regime II, may have primary contribution to the lower crystallization kinetics, also as a result to the higher degree of crystallinity and lower melting point in contrast to that of neat PLA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1100–1113, 2007     

Crystallization kinetics and crystallization behavior of syndiotactic polystyrene/clay nanocomposites

We investigated the effects of montmorillonite (clay) on the crystallization kinetics of syndiotactic polystyrene (sPS) with isothermal differential scanning calorimetry analyses. The clay was dispersed into the sPS matrix via melt blending on a scale of 1–2 nm or up to about 100 nm, depending on the surfactant treatment. For a crystallization temperature of 240 °C, the isothermal crystallization data were fitted well with the Avrami crystallization equation. Crystallization data on the kinetic parameters (i.e., the crystallization rate constant, Avrami exponent, clay content, and clay/surfactant cation‐exchange ratio) were also investigated. Experimental results indicated that the crystallization rate constant of the sPS nanocomposite increased with increasing clay content. The clay played a vital role in facilitating the formation on the thermodynamically more favorable all‐β‐form crystal when the sPS was melt‐crystallized. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2097–2107, 2001     

Non-isothermal crystallization of MaterBi-Z/clay nanocomposites

Non-isothermal crystallization of MaterBi-Z (starch-polycaprolactone blend) and its nanocomposites with different clay contents (0, 2.5 and 5 mass%) was studied. The experimental data show that clay can be act both as nucleating or retarding agent depend on the clay content. Kinetic parameters obtained by using a non-linear regression method, i.e., Kamal’s model and Dietz’s modification, were able to describe the non-isothermal crystallization behavior of the studied materials. A full model that takes into account the induction and growth of the crystal during cooling under non-isothermal conditions was used to obtain a continuous cooling transformation diagrams.     

Surface energetics,dispersion, and nanotribomechanical behavior of POSS/PP hybrid nanocomposites

Hybrid organic–inorganic polymer nanocomposites incorporating polyhedral oligomeric silsesquioxane (POSS) nanoparticles are of increasing interest for high performance materials applications. Octaisobutyl POSS/polypropylene nanocomposites were prepared at varying POSS concentrations via melt blending. The interplay of POSS molecular geometry, composition, and concentration in relation to the tribological, nanomechanical, surface energy, and bulk properties of the nanocomposites were investigated. Ultra‐low friction and enhanced hardness, modulus, and hydrophobicity were observed for the nanocomposite surfaces, with minimal changes in the bulk thermomechanical properties. Parallel AFM, SEM, TEM, and spectroscopic analyses demonstrated significant differences in POSS distribution and aggregation in the surface and the bulk, with preferential segregation of POSS to the surface. Additionally, contact angle studies reveal significant reduction in surface energy and increase in hysteresis with incorporation of POSS nanoparticles. The differences in bulk and surface properties are largely explained by the gradient concentration of POSS in the polymer matrix, driven by POSS/POSS and POSS/polymer interactions. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2441–2455, 2007     

Non-isothermal crystallization behaviors of polyamide 6/clay nanocomposites

The non-isothermal crystallization behaviors of polyamide 6/clay nanocomposite (PA6CN) were investigated by differential scanning calorimetry (DSC) and X-ray diffraction (XRD). DSC results showed that the nanometric silicate layers in PA6CN acted as effective nucleation agents. The addition of silicate layers influenced the mechanism of nucleation and the growth of PA6 crystallites. The DSC results also implied an unusual phenomenon, in contrast to PA6, the crystallinity degree of PA6CN increased with increasing cooling rate. XRD results verified this phenomenon and indicated that the addition of silicate layers favored the formation of the γ crystalline form.     

Microstructure and fracture behavior of semicrystalline polymer–clay nanocomposites

The relationships between the microstructure and the fracture behavior of three polymer/clay nanocomposites were studied. Two different polymer matrices were chosen, namely polyamide‐6 and polyethylene (compatibilized with PE‐g‐MA or PE‐g‐PEo), to reach very different clay dispersion states. The microstructure was characterized in terms of polymer crystallinity, orientation of the polymer crystalline lamellae, clay dispersion state, and orientation of the clay tactoids. The mechanical behavior was characterized by tensile tests. The essential work of fracture (EWF) concept was used to determine the fracture behavior of the nanocomposites. Both tensile and EWF tests were performed in two perpendicular directions, namely longitudinal and transversal. It is shown that the fracture behaviors of the matrices mainly depend on the polymer crystalline lamellae orientation. For the nanocomposites, the relationships between the matrix orientation, the clay dispersion states, the values of the EWF parameters (w_e and βw_p), and their anisotropy are discussed. The results show that the lower the average clay tactoid thickness, the lower is the decrease of fracture performance for the nanocomposite and the more consumed energy as longer the path of the crack. Besides, a linear dependence of the anisotropy of the EWF parameters of the nanocomposites on the average clay aspect ratio is found. The more exfoliated the structure is, the less pronounced the anisotropy of the EWF parameters. Interestingly, it is thought that the average clay aspect ratio is the parameter representing the clay dispersion state that governs the fracture anisotropy of the nanocomposites (as the elastic properties determined by tensile tests). © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1820–1836, 2008     

Preparation and characterization of PP/clay nanocomposites based on modified polypropylene and clay

X‐ray diffraction and differential scanning calorimeter (DSC) methods have been used to investigate the crystallization behavior and crystalline structure of hexamethylenediamine (HMDA)‐modified maleic‐anhydride‐grafted polypropylene/clay (PP‐g‐MA/clay) nanocomposites. These nanocomposites have been prepared by using HMDA to graft the PP‐g‐MA (designated as PP‐g‐HMA) and then mixing the PP‐g‐HMA polymer in hot xylene solution, with the organically modified montmorillonite. Both X‐ray diffraction data and transmission electron microscopy images of PP‐g‐HMA/clay nanocomposites indicate that most of the swellable silicate layers are exfoliated and randomly dispersed into PP‐g‐HMA matrix. DSC isothermal results revealed that introducing 5 wt % of clay into the PP‐g‐HMA structure causes strongly heterogeneous nucleation, which induced a change of the crystal growth process from a three‐dimensional crystal growth to a two‐dimensional spherulitic growth. Mechanical properties of PP‐g‐HMA/clay nanocomposites performed by dynamic mechanical analysis show significant improvements in the storage modulus when compared to neat PP‐g‐HMA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3242–3254, 2005     

Isothermal crystallization behavior of exfoliated‐PP/IMMT nanocomposites via in situ polymerization

Highly exfoliated isotactic‐polypropylene/alkyl‐imidazolium modified montmorillonite (PP/IMMT) nanocomposites have been prepared via in situ intercalative polymerization. TEM and XRD results indicated that the obtained composites were highly exfoliated PP/IMMT nanocomposites and the average thickness of IMMT in PP matrix was less than 10 nm, and the distance between adjacent IMMT particles was in the range of 20–200 nm. The isothermal crystallization kinetics of highly exfoliated PP/IMMT nanocomposites were investigated by using differential scanning calorimeter(DSC) and polarized optical microscope (POM). The crystallization half‐time t_1/2, crystallization peak time t_max, and the Avrami crystallization rate constant K_n showed that the nanosilicate layers accelerate the overall crystallization rate greatly due to the nucleation effect, and the crystallization rate was increased with the increase in MMT content. Meanwhile, the crystallinity of PP in nanocomposites decreased with the increase in clay content which indicated the PP chains were confined by the nanosilicate layers during the crystallization process. Although the well‐dispersed silicate layers did not have much influence on spherulites growth rate, the nucleation rate and the nuclei density increased significantly. Accordingly, the spherulite size decreased with the increase in MMT content. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2215–2225, 2009     

Non-isothermal crystallization and oxygen permeability of PP/PLA/EVOH ternary blends

Journal of Thermal Analysis and Calorimetry - Casting films of polypropylene (PP), poly(lactic acid) (PLA) and ethylene vinyl alcohol copolymer (EVOH) ternary blends having different compositions...     

Polymorphic behavior in syndiotactic polystyrene/clay nanocomposites

X‐ray diffraction methods were used in an investigation of the structural changes in syndiotactic polystyrene (sPS)/clay nanocomposites. sPS/clay was prepared by the intercalation of sPS polymer into layered montmorillonite. Both X‐ray diffraction data and transmission electron microscopy micrographs of sPS/clay nanocomposites indicated that most of the swellable silicate layers were exfoliated and randomly dispersed in the sPS matrix. The X‐ray diffraction data also showed the presence of polymorphism in the sPS/clay nanocomposites. This polymorphic behavior was strongly dependent on the thermal history of the sPS/clay nanocomposites from the melt and on the content of clay in the sPS/clay nanocomposites. Quenching from the melt induced crystallization into the α‐crystalline form, and the addition of montmorillonite probably increased heterophase nucleation of the α‐crystalline form. The effect of the melt crystallization of sPS and sPS/clay nanocomposites at different temperatures on the crystalline phases was also examined. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 736–746, 2002     

Non-isothermal crystallization behavior of isotactic polypropylene/copper nanocomposites

Journal of Thermal Analysis and Calorimetry - The Non-isothermal crystallization behavior of isotactic polypropylene (iPP)/copper nanocomposites with four different mass percentages (0.5, 1.0, 2.0...     

Metallocene-mediated synthesis of chain-end functionalized polypropylene and application in PP/clay nanocomposites

This paper summarizes our research in the preparation of chain end functionalized isotactic polypropylene (PP) having a terminal functional group, such as Cl, OH, and NH₂. The chemistry involves metallocene-mediated propylene polymerization using rac-Me₂Si[2-Me-4-Ph(Ind)]₂ZrCl₂/MAO complex in the presence of styrene derivatives (St-f) and hydrogen, which serve as the chain transfer agents. The molecular weight of the resulting PP polymers with a terminal Cl, OH and NH₂ group (i.e., PP-t-Cl, PP-t-OH and PP-t-NH₂) are inversely proportional to the molar ratio of [St-f]/[propylene]. Despite the extremely low concentration of functional group, the high molecular weight chain end functionalized PP-t-OH and exhibit a distinctive advantage over other functional PP polymers containing side chain functional groups or long functional blocks. The terminal hydrophilic OH and cations, with good mobility and reactivity, effectively hydrogen bond and ion-exchange the cations (Li⁺, Na⁺, etc.) located between the clay interlayers, respectively. Such interactions anchor the PP chain to the clay surfaces. On the other hand, the remaining rest of the unperturbed end-tethered high molecular weight PP tail exfoliates the clay layers. This exfoliated structure is maintained even after further mixing of the PP-bearing platelets with pure neat PP polymers.     

New insight into the crystallization behavior of poly(ethylene terephthalate)/clay nanocomposites

Crystallization behavior of poly(ethylene terephthalate) (PET)/clay nanocomposites has been investigated in terms of differential scanning calorimeter (DSC) analysis, polarizing optical microscopy (POM), and scanning electron microscopy (SEM) observation. The nanocomposites for investigation were prepared via in situ polycondensation. Crystalline morphologies were observed through POM and SEM. The nonisothermal and isothermal crystallization rates of different samples were determined for comparison based on DSC data. Secondary nucleation analysis was also performed based on bulk crystallization data derived from DSC analysis. The results revealed that nucleating abilities of montmorillonites (MMT) depended on the dispersion state of clay in matrix, the surface modification status, and the metallic derivatives released from MMT during in situ synthesis. The quantities of metallic elements released were measured by inductively coupled plasma (ICP) analysis. The results showed that the release of these metallic derivatives was also affected by surfactant molecules anchored on the surface of MMT. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2380–2394, 2008     

Nonisothermal crystallization behavior of syndiotactic polystyrene/montmorillonite nanocomposites

X‐ray diffraction methods and differential scanning calorimetry were used to investigate the crystalline structure and crystallization kinetics of syndiotactic polystyrene (sPS)/clay nanocomposites. X‐ray diffraction data showed the presence of polymorphism in sPS/montmorillonite (MMT) nanocomposites, which was strongly dependent on the processing conditions (premelting temperature and cooling rate) of the sPS/MMT nanocomposites and on the content of MMT in the sPS/MMT nanocomposites. The α‐crystalline form could be transformed into β‐crystalline forms at higher premelting temperatures. The nonisothermal melt‐crystallization kinetics and melting behavior of the sPS/MMT nanocomposites were also studied at various cooling rates. The correlation of the crystallization kinetics, melting behavior, and crystalline structure of the sPS/MMT nanocomposites was examined. The results indicated that the addition of a small amount of MMT to sPS caused a change in the mechanism of nucleation and the crystal growth of the sPS crystallite. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 560–570, 2003     

Fire retardancy behavior of PLA based nanocomposites

To understand and improve the fire retardancy behavior of polylactic acid, we have incorporated two structurally different additives, sepiolite and organically modified montmorillonite. A novel approach (combination of electrospinning and extrusion/injection molding) is employed to address critical issues like char enhancement as well as the homogeneity/uniformity of the inorganic barrier during combustion of polymer nanocomposites. Fundamental knowledge is gained on the mechanisms of fire retardancy, particularly with samples of different thicknesses (thermally thin versus thermally intermediate/thick). Volumetric imaging of the residues provided a deeper understanding of the formation or the evolution of the inorganic barrier. Considerable insight on the dependency of biodegradation on the environment (primarily) and on the compromising effect of high aspect ratio nanoparticles is also obtained. This knowledge has a broader scientific impact and is critical to design the new generation of eco-benign flame retardant and biodegradable polymer nanocomposites.     

New PP/PLA/cellulose composites: effect of cellulose functionalization on accelerated weathering behavior (accelerated weathering behavior of new PP/PLA/cellulose composites)

Polylactic acid (PLA) was used as partial replacement for conventional thermoplastic matrix, new composites comprising cellulose, polypropylene (PP), and PLA being realized. In order to obtain a compatible interface between cellulosic pulp and polymeric matrix, two chemical modifications of cellulose with stearoyl chloride and toluene di‐isocyanate (TDI) were performed, structural changes being evidenced by X‐ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. The composite materials were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, dynamic scanning calorimetry, impact, tensile and melt rheological tests, surface tension, and dynamic vapor sorption. Because promising results for impact strength and Young modulus were recorded when replacing 15% of PP with PLA in blends of PP with the same cellulosic pulp load, the aim of our study was to assess the behavior to accelerate weathering of composites comprising PP, cellulosic pulp, and PLA. Although the slight decrease in the mechanical properties was recorded after accelerated weathering, the use of functionalized cellulose successfully prevented the deterioration of surface materials, especially for composite comprising stearoyl chloride treated cellulose pulp. Copyright © 2015 John Wiley & Sons, Ltd.     

Nonisothermal crystallization behavior of polypropylene-clay nanocomposites

The influence of two concentrations of clay nanoparticles on the nonisothermal crystallization behavior of the intercalated polypropylene-clay nanocomposites is investigated here. It is observed that the crystallization peak temperature (T_p) of PP-clay nanocomposites is marginally higher than neat PP at various cooling rates. Furthermore, the half-time for crystallization (t_0.5) decreased with increase in clay content, implying the nucleating role of clay nanoparticles. The nonisothermal crystallization data is analyzed using Avrami, Ozawa and Mo and coworkers methods. The validity of kinetic models on the nonisothermal crystallization process of PP-clay nanocomposites is discussed. The approach developed by Mo and coworkers successfully describes the nonisothermal crystallization behavior of PP and PP-clay nanocomposites. The activation energy for nonisothermal crystallization of pure PP and PP-clay nanocomposites based on Kissinger method is evaluated.