Electrochemical properties of liquid electrolyte added quasi-solid state TiO2 dye-sensitized solar cells

In this study a process has been introduced to replace traditional liquid or solid electrolyte coatings on dye-sensitized photoelectrode in solar cells. This process has more efficient diffusion of electrolyte, hence higher sensitivity. Better interfacial contact between polymer electrolyte and TiO₂ photoelectrode had improved electrochemical response and ionic conductivity of cell. Conductivity of this electrode was 9.33 × 10⁻³ S cm⁻¹ (at room temperature), which is much higher than the using traditional process for addition of electrolytes. It has 0.68 V open-circuit voltage and 3.19 mA cm⁻² short-circuit current density. Energy conversion efficiency of this cell was about 37% higher than the cell developed with traditional processes under constant light intensity (45 mW cm⁻²).     

Solidifying liquid electrolytes with fluorine polymer and silica nanoparticles for quasi-solid dye-sensitized solar cells

Poly(vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP) and silica nanoparticles were employed to solidify 3-methoxypropionitrile based liquid electrolytes containing an ionic liquid, 1-methyl-3-propylimidazolium iodide, as iodide resource. These new quasi-solid-state electrolytes were successfully used for regenerative phtoelectrochemical cells that yielded about 6.7% efficiency under simulated full sunlight (air mass 1.5, 100 mW cm⁻²) in combination with an amphiphilic ruthenium polypyridyl photosensitizer. The as-fabricated device showed a good thermostability at 80 °C for 30 days, maintaining higher than 90% of its initial performance.     

ZnO hierarchical structures for efficient quasi-solid dye-sensitized solar cells

We report a direct precipitation method for mass production of ZnO microflowers (MFs) containing hierarchical structures. The ZnO MFs are constructed by interlaced single crystalline and porous nanosheets which are ideal photoanode material for dye-sensitized solar cells (DSCs) because the MFs can largely improve the energy harvesting performance and the efficiency of DSCs. Compared with other forms of nano-sized structures, the novel hierarchical structures show obvious advantages in DSC application because of their large surface area for dye-loading, good light scattering efficiency and excellent electrical transport property. The quasi-solid state DSCs fabricated with the MF hierarchical structures exhibited an efficiency of 4.12%, much higher than that of ZnO nanoparticle-based DSCs, indicating a great potential for the development of highly-efficient quasi-solid DSCs.     

Butyronitrile-based electrolyte for dye-sensitized solar cells

We elaborated a new electrolyte composition, based on butyronitrile solvent, that exhibits low volatility for use in dye-sensitized solar cells. The strong point of this new class of electrolyte is that it combines high efficiency and excellent stability properties, while having all the physical characteristics needed to pass the IEC 61646 stability test protocol. In this work, we also reveal a successful approach to control, in a sub-Nernstian way, the energetics of the distribution of the trap states without harming cell stability by means of incorporating NaI in the electrolyte, which shows good compatibility with butyronitrile. These excellent features, in conjunction with the recently developed thiophene-based C106 sensitizer, have enabled us to achieve a champion cell exhibiting 10.0% and even 10.2% power conversion efficiency (PCE) under 100 and 51.2 mW·cm(-2) incident solar radiation intensity, respectively. We reached >95% retention of PCE while displaying as high as 9.1% PCE after 1000 h of 100 mW·cm(-2) light-soaking exposure at 60 °C.     

Latent gel electrolyte precursors for quasi-solid dye sensitized solar cells

New latent chemically-cross-linked gel electrolyte precursors for quasi-solid dye sensitized solar cells (QDSC) are reported. The gel electrolyte precursors consist of nano-particles and dicarboxylic acids as the latent gelators. The viscosity of the precursor is low at first and does not increase during storage at room temperature. However, when the precursor is baked at 80 degrees C, it solidifies immediately. Photo-voltaic performance is maintained after solidification.     

Molecular engineering and theoretical investigation of organic sensitizers based on indoline dyes for quasi-solid state dye-sensitized solar cells

Novel indoline dyes, I-1-I-4, with structural modification of π-linker group in the D-π-A system have been synthesized and fully characterized. Molecular engineering through expanding the π-linker segment has been performed. The ground and excited state properties of the dyes have been studied by means of density functional theory (DFT) and time-dependent DFT (TD-DFT). Larger π-conjugation linkers would lead to broader spectral response and higher molar extinction coefficient but would decrease dye-loaded amount on TiO(2) electrode and LUMO level. While applied in DSSCs, the variation trends in short-circuit current density (J(sc)) and open-circuit voltage (V(oc)) were observed to be opposite to each other. The internal reasons were studied by experimental data and theoretical calculations in detail. Notably, I-2 showed comparable photocurrent values with liquid and quasi-solid state electrolyte, which suggested through molecular engineering of organic sensitizers the dilemma between optical absorption and charge diffusion lengths can be balanced well. Through studies of photophysical, electrochemical, and theoretical calculation results, the internal relations between chemical structure and efficiency have been revealed, which serve to enhance our knowledge regarding design and optimization of new sensitizers for quasi-solid state DSSCs, providing a powerful strategy for prediction of photovoltaic performances.     

A supercooled imidazolium iodide ionic liquid as a low-viscosity electrolyte for dye-sensitized solar cells

A series of allyl-functionalized imidazolium salts are reported, including 1-allyl-3-ethylimidazolium iodide and 1-allyl-3-propylimidazolium iodide, which have melting points close to room temperature and show typical properties of supercooled fluids if heated above their melting points. Their viscosities in the liquid state are considerably lower than the benchmark ionic liquid used in solar cells, viz., 1-propyl-3-methylimidazolium iodide. Electrolytes containing these new liquids provide excellent efficiencies and good stability in dye-sensitized solar cells when subjected to an accelerated-light soaking test at 60 degrees C. The structures of three of the new salts have been established in the solid state by single-crystal X-ray analysis.     

High efficiency dye-sensitized nanocrystalline solar cells based on ionic liquid polymer gel electrolyte

An ionic liquid polymer gel containing 1-methyl-3-propylimidazolium iodide (MPII) and poly(vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP) has been employed as quasi-solid-state electrolyte in dye-sensitized nanocrystalline TiO2 solar cells with an overall conversion efficiency of 5.3% at AM 1.5 illumination.     

Ambient temperature plastic crystal electrolyte for efficient, all-solid-state dye-sensitized solar cell

Doping the molecular plastic crystal of succinonitrile with solid N-methyl-N-butylpyrrolidinium iodide salt and iodine has produced a highly conductive solid iodide/triiodide conductor. Furthermore, it was employed for a highly efficient, all-solid-state dye-sensitized solar cell.     

A novel composite polymer electrolyte containing room-temperature ionic liquids and heteropolyacids for dye-sensitized solar cells

A novel composite polymeric gel comprising room-temperature ionic liquids (1-butyl-3-methyl-imidazolium-hexafluorophosphate, BMImPF₆) and heteropolyacids (phosphotungstic acid, PWA) in poly(2-hydroxyethyl methacrylate) matrix was successfully prepared and employed as a quasi-solid state electrolyte in dye-sensitized solar cells (DSSCs). These composite polymer electrolytes offered specific benefits over the ionic liquids and heteropolyacids, which effectively enhanced the ionic conductivity of the composite polymer electrolyte. Unsealed devices employing the composite polymer electrolyte with the 3% content of PWA achieved the solar to electrical energy conversion efficiency of 1.68% under irradiation of 50 mW cm⁻² light intensity, increasing by a factor of more than three compared to a DSSC with the blank BMImPF₆-based polymer electrolyte without PWA. It is expected that these composite polymer electrolytes are an attractive alternative to previously reported hole transporting materials for the fabrication of the long-term stable quasi-solid state or solid state DSSCs.     

Study of quasi-solid electrolyte in dye-sensitized solar cells using surfactant as pore-forming materials in TiO<Subscript>2</Subscript> photoelectrodes

A novel polymer gel electrolyte was used to improve the performance and long-term stability in dye-sensitized solar cells (DSSCs). The polymer gel electrolyte (PGE) was prepared by mixing 5 wt% poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) and 2 % TiO₂ nanoparticles. The conductivity of PGE with P25 reached 9.98 × 10^?3 S/cm, which increased by 34.9 % compared with 7.40 × 10^?3 S/cm of PGE without P25, and the diffusion coefficient was also increased by 19.0 %. Different photoelectrodes were obtained by using three kinds of surfactants (cetylamine, octadecylamine, and P123) as pore-forming materials, and their morphologies were contrasted through scanning electron microscopy (SEM). The results showed that gel electrolyte can increase the short-circuit current density (J _sc) from 11.01 to 12.99 mA/cm² in DSSCs. Moreover, unlike the liquid electrolyte, the gel electrolyte is more conducive to the TiO₂ photoelectrodes with larger pores. In conclusion, the efficiency of DSSC with gel electrolyte and P123 as pore-forming material was 6.73 %, which was 12 % higher than the liquid electrolyte in the same test condition. In addition, the sealed gel electrolyte DSSCs showed better stability than did liquid electrolyte DSSCs during nearly 600 h.     

Ionic liquid integrated polyethylene glycol (PEG)-based quasi-solid electrolyte for efficiency enhancement of dye-sensitized solar cell

Journal of Solid State Electrochemistry - We are presenting herein the effect of using three different cell electrolytes namely: (a) propylene carbonate containing 0.2&nbsp;M LiI and...     

The effects of polymer gel electrolyte composition on performance of quasi-solid-state dye-sensitized solar cells

Polymer gel electrolytes based on poly(acrylic acid)-poly(ethylene glycol) (PAA–PEG) hybrid have been prepared and applied to developed quasi-solid-state dye-sensitized solar cells (DSCs). PAA–PEG hybrid was synthesized by polymerization reaction. Quasi-solid-state DSCs were fabricated with synthesized PAA–PEG electrolyte. The effects of alkali iodides LiI, KI, and I₂ concentrations on liquid electrolyte absorbency and ionic conductivity of PAA–PEG were investigated. The evolution of the solar cell parameters with polymer gel electrolyte compositions was revealed. DSCs based on PAA–PEG with optimized KI/I₂ concentrations showed better performances than those with optimized LiI/I₂ concentrations. The electrochemical impedance spectroscopy technique was employed to examine the electron lifetime in the TiO₂ electrode and quantify charge transfer resistances at the TiO₂/dye/electrolyte interface and the counter electrode in the solar cells based on the PAA–PEG hybrid gels. A maximum conversion efficiency of 4.96% was obtained for DSCs using KI based quasi-solid electrolyte under 100 mW cm⁻². Our work suggests that KI can be the promising alkali metal iodide for improving the performance of PAA–PEG hybrid gel DSCs.     

A novel deep eutectic solvent-based ionic liquid used as electrolyte for dye-sensitized solar cells

We utilize a quaternary ammonium salt-derivative ionic liquid called G.CI which is a eutectic mixture of glycerol and choline iodide as electrolyte for dye-sensitized solar cells. Such eutectic compound belongs to a new series of ionic liquid called deep eutectic solvents (DES), which possess many outstanding features compared to the traditional imidazolium-based ionic liquids including cheap raw materials, simple preparation procedures and better biocompatibility. Current–voltage characteristics of the G.CI/PMII-based binary electrolytes stand at 0.533 V on V_oc, 12.0 mA cm^?2 on J_sc, 0.582 on fill factor, and 3.88% cell efficiency under AM 1.5, 100 mW/cm² illuminations. The comparable cell performance together with all the above advantages makes G.CI as a strong candidate for future electrolyte development for dye-sensitized solar cells (DSSCs).     

Low-bandgap donor-acceptor conjugated polymer sensitizers for dye-sensitized solar cells

A set of two donor-acceptor type conjugated polymers with carboxylic acid side groups have been synthesized and utilized as active materials for dye-sensitized solar cells (DSSCs). The polymers feature a π-conjugated backbone consisting of an electron-poor 2,1,3-benzothiadiazole (BTD, acceptor) unit, alternating with either a thiophene-fluorene-thiophene triad (2a) or a terthiophene (3a) segment as the donor. The donor-acceptor polymers absorb broadly throughout the visible region, with terthiophene-BTD polymer 3a exhibiting an absorption onset at approximately 625 nm corresponding to a ～1.9 eV bandgap. The polymers adsorb onto the surface of nanostructured TiO(2) due to interaction of the polar carboxylic acid units with the metal oxide surface. The resulting films absorb visible light strongly, and their spectra approximately mirror the polymers' solution absorption. Interestingly, a series of samples of 3a with different molecular weight (M(n)) adsorb to TiO(2) to an extent that varies inversely with M(n). DSSCs that utilize the donor-acceptor polymers as sensitizers were tested using an I(-)/I(3)(-) electrolyte. Importantly, for the set of polymer sensitizers 3a with varying M(n), the DSSC efficiency varies inversely with M(n), a result that reflects the difference in adsorption efficiency observed in the film absorption experiments. The best DSSC cell tested is based on a sample of 3a with M(n) ～ 4000, and it exhibits a ～65% peak IPCE with J(sc) ～12.6 mA cm(-2) under AM1.5 illumination and an overall power conversion efficiency of ～3%.     

Interface modification of 8-hydroxyquinoline aluminium with combined effects in quasi-solid dye-sensitized solar cells

In this paper, 8-hydroxyquinoline aluminium (Alq(3)) was used in interface modification of dye-sensitized solar cells (DSCs). Alq(3) was the first discovered interface modification material with combined effects of retarding charge recombination and F?rster resonant energy transfer (FRET). Results of dark current curve and AC impedance showed that Alq(3) could retard charge recombination in DSCs. I-V curves showed that conversion efficiency increased with Alq(3) modification. Besides the interface modification effect, it was discovered that Alq(3) also acted as energy relay dye with the FRET effect between itself and N3, which increased photoresponse and electron injection. The application of Alq(3) with combined effects opened a new door to explore more novel multi-functional interface modification materials to improve the performance of DSCs.     

Electrophoretic deposition of ZnO photoanode for plastic dye-sensitized solar cells

Plastic dye-sensitized solar cells have been fabricated based on an organic dye (D 149) and ZnO photoanode prepared via room temperature electrophoretic deposition (EPD) to yield a conversion efficiency of 4.17% under 100 mW cm^?2 AM 1.5 illumination. Intensity modulated photocurrent spectroscopy analyses reveal that the fabricated ZnO electrodes have adequate interparticle connection, even in the absence of any post-treatment. This study demonstrates that EPD is a convenient method for photoanode fabrication and ZnO photoelectrodes obtained via EPD are promising for efficient plastic solar cells.     

A promising heat-induced supramolecular metallogel electrolyte for quasi-solid-state dye-sensitized solar cells

Journal of Solid State Electrochemistry - A series of Fe(III)-based coordination-driven metallogel (MOG) electrolytes are obtained by absorbing liquid electrolytes with MOGs and applied to...     

The conducting polymer electrolyte based on polypyrrole-polyvinyl alcohol and its application in low-cost quasi-solid-state dye-sensitized solar cells

The effect of polypyrrole (PPy) on the polyvinyl alcohol (PVA)-potassium iodide (KI)-iodine (I₂) polymer electrolytes has been investigated and optimized to use in a dye-sensitized solar cell (DSSC). The different weight ratios of PVA: PPy (93: 2, 91: 4, 89: 6, 87: 8, and 85: 10 wt%) polymer electrolytes (PE) were prepared by solution casting. Structural, complex formation and surface roughness of the prepared electrolytes was confirmed by X-ray diffraction, FTIR, and atomic force microscopy (AFM) respectively. Conductivity plots of all polymer films showed increasing trend with temperature and concentration of PPy. The activation energy of the optimized system found to be 0.871 kJ mol^?1. UV-visible spectrum was adopted to characterize the absorption spectra of the material revealed that increase in the absorbance with increasing PPy content and shifting the absorbance maximum towards lower energy. The indirect band gap decreased from 3.78 to 2.14 eV and direct band gap decreased from 3.88 to 2.71 eV. The EIS analyses revealed the lower charge transfer resistance of 3.029 Ω cm² at the interface between CE and PE. The excellent performance was observed in the fabricated DSSCs using PVA (85%)/PPy (10%)/KI (5%)/I₂ polymer electrolyte with a short-circuit current density of 11.071 mA cm^?2, open-circuit voltage of 0.644 V, fill factor of 0.575, and photovoltaic conversion efficiency of 4.09% under the light intensity of 100 mW cm^?2. Hence, the PPy content in polymer electrolyte influences the remarkable performance of low-cost DSSC.