Metal adsorbent for alkaline etching aqua solutions of Si wafer

High performance adsorbent is expected to be synthesized for the removal of Ni and Cu ions from strong alkaline solution used in the surface etching process of Si wafer. Fibrous adsorbent was synthesized by radiation-induce emulsion graft polymerization onto polyethylene nonwoven fabric and subsequent amination. The reaction condition was optimized using 30 L reaction vessel and nonwoven fabric, 0.3 m width and 18 m long. The resulting fibrous adsorbent was evaluated by 48 wt% NaOH and KOH contaminated with Ni and Cu ions, respectively. The concentration levels of Ni and Cu ions was reduced to less than 1 μg/kg (ppb) at the flow rate of 10 h^?1 in space velocity. The life of adsorbent was 30 times higher than that of the commercialized resin. This novel adsorbent was commercialized as METOLATE^® since the ability of adsorption is remarkably higher than that of commercial resin used practically in Si wafer processing.     

Structures and magnetic properties of imidazolate-bridged tetranuclear and polymeric copper(II) complexes

Eight kinds of imidazolate-bridged copper(II) complexes were found to be classified into two categories from the magnetic properties. The crystal structures of [Cu(L)(μ-im)]_n (Him = imidazole; L = nonane-4,6-dionate, 2,6-dimethylheptane-3,5-dionate) and [Cu(L)(μ-im)]₄ (L = nonane-4,6-dionate, 1-phenylbutane-1,3-dionate) were determined, to reveal that they consist of polymeric chains and tetranuclear cycles, respectively. Note that the nonane-4,6-dionate derivative gave the two phases. The Bonner–Fisher model (a one-dimensional antiferromagnetic chain model) was plausibly applied to [Cu(L)(μ-im)]_n for the best fit, while a square model was to [Cu(L)(μ-im)]₄. The complexes with unknown crystal structures were also subjected to magnetic measurements, and the tetra- and polymeric structures could be clearly distinguished from each other by fitting the magnetic data to appropriate models. The exchange parameters were comparable for both series (2J/k_B = ?78 to ?97 K) because the structurally common bridges Cu–N(eq)–N(eq)–Cu afford comparable magnitudes of couplings.     

Iron,copper, zinc and bromine mapping in cirrhotic liver slices from patients with hemochromatosis studied by microscopic synchrotron radiation X-ray fluorescence analysis in continuous scanning mode

Iron (Fe) and copper (Cu) are essential metals in physiological cell metabolism. While Fe is easy to determine biochemically in histological slices, Cu and zinc (Zn) distribution is frequently critical in confirming the presence of an overload in disturbed Fe/Cu metabolism. To analyze Fe, Cu and Zn in a near histological resolution, energy dispersive microscopic synchrotron radiation X-ray fluorescence was applied.In normal liver tissue, after fixation and imbedding in paraffin, mean Fe, Cu and Zn concentrations were 152 ± 54, 20.1 ± 4.3 and 88.919.5 μg/g sample weight, respectively. No substantial, characteristic differences in their distribution were found in the two-dimensional scans. In slices from patients with hemochromatosis mean Fe, Cu and Zn concentrations were 1102 ± 539, 35.9 ± 14.6 and 27.2 ± 6.7 μg/g sample weight, respectively. Additionally, a significant decrease in phosphorus and sulphur concentrations existed. An increased Cu around cirrhotic regenerations nodules is mostly associated with a lymphocytic infiltration in this region. Analyzing concentrations of Fe in different regions of the samples show a clear negative dependency between Fe and Cu, Cu and Zn, but a positive one between Fe and Zn.Conclusion: With a focal beam size of 15 μm in diameter a resolution of the elemental distribution was achieved which is widely comparable with stained histological slices (20× light microscope). The analysis of simultaneous determined elements reveals metabolic differences between Fe, Cu and Zn in liver tissue from patients with hemochromatosis.     

Electrodeposition of copper in the presence of an acoustically excited gas bubble

Copper has been electrodeposited in the presence of an acoustically excited gas bubble (Ar bubbles with radii ∼1.5 mm held below a copper plate). Under the conditions employed, an acoustic pressure amplitude of 69.5 Pa is sufficient to excite multiple surface wave modes on the bubble wall. This is observed using high-speed imaging. This oscillation generates significant micromixing, which brings fresh electrolyte to the electrode surface leading to an enhanced deposition current. Scanning electron microscopy reveals radial streaming patterns in the resulting copper deposit. Experiments carried out using a lower acoustic pressure amplitude of 50.5 Pa (such that only the Faraday wave is excited) exhibit a lesser degree of streaming and mass transfer enhancement. No significant spatially averaged current enhancement is seen if the bubble is only undergoing breathing mode oscillation.     

Coordination polymers incorporating copper(II) and manganese(II) centers bridged by pyridinedicarboxylate ligands: Structure and magnetism

Two heterobimetallic coordination polymers, [Cu(2,4-pydc)₂Mn(H₂O)₄]_x (1) and [Cu(2,5-pydc)₂Mn(H₂O)₂]_x · 4xH₂O (2), have been synthesized and structurally characterized by single crystal X-ray diffraction. Both compounds have extended 2-D sheet structures. In 1 the copper centers are linked in chains by double ligand bridges and these chains are cross-linked through the manganese coordination spheres and O–C–O bridges to form polymeric sheets. In 2 separate O–C–O bridged Cu and Mn chains are connected in an alternating array by additional ligand bridging to generate the overall 2-D structure. Analysis of magnetic data of 1 reveals that ferromagnetic exchange between the O–C–O bridged copper and manganese centers dominates the magnetic properties of this system. The magnetic data for 2 fit well to a model incorporating antiferromagnetic exchange in independent S = 1/2 and S = 5/2 linear chains with J(Cu) = −0.073 cm⁻¹ and J(Mn) = −0.32 cm⁻¹. Unlike the situation in 1, there is no evidence for heterometallic exchange. In both 1 and 2 the significant exchange occurs via O–C–O bridges. To study the effect of thermal dehydration on the magnetic properties of these systems, the compounds Cu(2,4-pydc)₂Mn · H₂O (1d) and Cu(2,5-pydc)₂Mn · H₂O (2d) were synthesized and studied.     

Kinetics of copper UPD on stepped platinum single crystals in the presence of acetonitrile

The kinetics of copper underpotential deposition on stepped Pt(h k l) electrodes with controlled width of (1 1 1) terraces in acidic solutions of copper sulfate with 0–200 mM of acetonitrile (AcN) has been studied by means of cyclic voltammetry. In the presence of AcN Cu UPD process is hindered both at (1 0 0) steps and (1 1 1) terraces of Pt(17 15 15) and Pt(7 5 5) faces due to blocking of the electrode surface with organic molecules, strongly adsorbed at the steps and nearby ones. The decoration of (1 1 0) steps with copper adatoms is slightly accelerated for Pt(7 7 5) electrode in the solution with 0.04 mM AcN. Increase in AcN concentration leads to inhibition of the UPD process. The difference in behavior of the stepped platinum electrodes is controlled by competitive adsorption of AcN, (bi)sulfate and Cu atoms at the step sites. AcN adsorption at (1 0 0) steps is stronger as compared with (1 1 0) ones.     

Magnetic interaction in 2D sheet structure of bis(1H, 4H-5,6-diethylpyrazinedithiolato) copper(II) trifluoroacetate

The metal complexes (M = Cu, Ni, Pd, and Pt) formed the 2D sheet structure mediated by trifluoroacetic acid which provide hydrogen bonding interactions within the sheet as well as electrostatic interactions between the sheets. The SQUID measurement of the Cu complex reveals the χT value of 0.381 emu K mol⁻¹ at room temperature, which is close to the calculated value for uncorrelated S = 1/2 spins. In the whole temperature range the χT value shows no dramatic changes, indicating the absence of strong magnetic interactions between the Cu complexes. The DFT calculation of the Cu complex supports the paramagnetic behavior.     

Recent advances in understanding blue copper proteins

The type 1 (T1) or blue Cu (BC) proteins are a highly studied group of electron transfer (ET) active sites in bioinorganic chemistry. In this review, we cover several more recent results which extend the understanding of the geometric and electronic structure of these interesting Cu ET sites. Spectroscopic methods in tandem with density functional theory (DFT) and time dependent-DFT (TD-DFT) calculations have been used in studies of S → Se variants as well as a series of metal-varied model complexes (M = Mn²⁺ → Zn²⁺). The ligand and metal perturbations further defined the origins of the unique spectral features of BC proteins. These unique spectral features show different temperature dependencies in different T1 sites, and contrasts drawn between their behaviors define the role of the protein in tuning the geometric and electronic structure of the BC site for function. This has been termed the ‘entatic’ or ‘rack-induced’ state in bioinorganic chemistry.     

Structures and magnetic properties of one-dimensional copper(II) complexes bridged with diazaaromatic rings

Seven kinds of polynuclear complexes of [Cu(hfac)₂] (Hhfac = 1,1,1,5,5,5-hexafluoropentane-2,4-dione) with diazaaromatic rings have been prepared. The crystal structures of [{Cu(hfac)₂(μ-L)}_n] (L = 2,5- and 2,6-dimethylpyrazines, propylpyrazine (prpyz), quinoxaline, phenazine, 4,6-dimethylpyrimidine, and 1,6-naphthyridine) have been determined. These complexes consist of a one-dimensional chain structure, and the geometry around the copper ion is approximately an octahedral structure. The relations between the magnetic properties and coordination structure were discussed from the magnetic measurements. In the μ-prpyz complex, one nitrogen atom is coordinated to a copper ion at an axial position, and at the same time the other coordinated at an equatorial site of a neighboring copper ion. This complex showed antiferromagnetic interaction with J/k_B = −0.086(3) K estimated from the Bonner–Fisher model. Weak magnetic interaction is caused by the somewhat long Cu–N distances due to the steric effect from the bridging ligands.     

Asymmetric nitroaldol reaction catalyzed by copper–diamine complexes: selective construction of two contiguous stereogenic centers

Chiral copper(II) complexes of secondary bisamines derived from 1,2-diaminocyclohexane were successfully used in the diastereoselective nitroaldol reaction. The reactions were carried out in the presence of 10 mol % of the Cu(II) complex and 7.7 mol % of i-Pr₂NEt in 2-propanol at ?30 °C. Good to excellent yields, enantioselectivities of up to 99%, and moderate to excellent diastereoselectivities were obtained for both aromatic or aliphatic aldehydes and various prochiral nitrocompounds forming the corresponding β-nitroalcohols with two contiguous stereocenters.     

Synthesis and crystal structure of sodium copper tetrametaphosphimate heptahydrate Na2Cu(PO2NH)4·7H2O and sodium potassium copper tetrametaphosphimate heptahydrate KxNa2−xCu(PO2NH)4·7H2O

Na₂Cu(PO₂NH)₄·7H₂O and K_xNa_2−xCu(PO₂NH)₄·7H₂O (x ≈ 0.5) were synthesized by gel crystallization in sodium silicate gels. The crystal structures were solved by single-crystal X-ray methods and found to be isotypic (Pnma, Z = 4; Na₂Cu(PO₂NH)₄·7H₂O: a = 627.5(2) pm, b = 1456.0(3) pm, c = 1900.5(4) pm, R1 = 0.0352; K_0.47Na_1.53Cu(PO₂NH)₄·7H₂O: a = 632.2(2) pm, b = 1460.0(3) pm, c = 1936.4(4) pm, R1 = 0.0345). The P₄N₄ rings of the tetrametaphosphimate anion exhibit a distorted chair-2 conformation with admixtures of saddle and crown conformation. The M⁺ ions are six- and sevenfold coordinated by oxygen atoms, the Cu²⁺ ions are fivefold coordinated, respectively. The MO₇ and the CuO₅ units form pairs of face-sharing polyhedra, which are connected by common corners forming chains and are further interconnected by tetrametaphosphimate anions, forming a three-dimensional network structure with channels along [100] and [010]. The MO₆ units form chains of face-sharing polyhedra, which are situated in the channels along [100]. Extended hydrogen bonding reinforces the three-dimensional framework structure of the compounds. ²³Na-MAS NMR experiments were conducted to verify the K/Na distribution on the M sites derived from the X-ray crystal structure refinement.     

Electro-reduction of cuprous chloride powder to copper nanoparticles in an ionic liquid

Cyclic voltammetry of the CuCl powder in a cavity microelectrode revealed direct electro-reduction in solid state in 1-butyl-3-methylimidazolium hexafluorophosphate. Potentiostatic electrolysis of the salt powder (attached to a current collector) in the ionic liquid produced Cu nanoparticles as confirmed by X-ray diffraction, energy dispersive X-ray analysis, scanning and transmission electron microscopy. The particle size decreased down to 10 nm when the electrode potential was shifted from −0.9 V to −1.8 V (versus Ag/Ag⁺). The electro-reduction and the nanoparticle formation mechanisms were investigated in the ionic liquid and also in aqueous 0.1 mol L⁻¹ KClO₄ in which larger Cu particles were obtained.     

Highly selective thiocyanate electrode based on bis-bebzoin-semitriethylenetetraamine binuclear copper(II) complex as neutral carrier

A novel selective thiocyanate PVC membrane electrode based on bis-bebzoin-semitriethylenetetraamine binuclear copper(II) [Cu(II)₂–BBSTA] as neutral carrier is reported, which displays an anti-Hofmeister selectivity sequence in following order: SCN⁻ > ClO₄⁻ > I⁻ >Sal⁻ >SO₃²⁻ >NO₃⁻ > H₂PO₄⁻ > Cl⁻ >NO₂⁻ > SO₄²⁻. The electrode exhibits Nernstian potential linear range to thiocyanate from 1.0 × 10⁻¹ to 9.0 × 10⁻⁷ mol/l with a detection limit 7.0 × 10⁻⁷ mol/l and a slope of −57.0 mV/decade in pH 5.0 of phosphorate buffer solution at 25 °C. The response mechanism is discussed in view of the AC impedance technique and the UV spectroscopy technique. From comparison of potentiometric response characteristics between the binuclear metallic complex copper(II) [Cu(II)₂–BBSTA] and mononuclear copper(II) metallic complex [Cu(II)–BBSDA], an enhanced response towards thiocyanate from the electrode based on binuclear metallic complex copper (II) [Cu(II)₂–BBSTA] was observed. The electrode based on binuclear copper(II) compound was used to determine the thiocyanate content in waste water with satisfactory results.     

Copper removal from aqueous solution using biochar: Effect of chemical activation

The main aim of this study was to test the efficiency of biochar for Cu removal from synthetic and soil solutions, respectively.The biochar was produced from brewers draff via pyrolysis. Additionally, the prepared biochar was also activated using 2 M KOH to enhance its sorption efficiency to remove Cu from both solutions. Two different aqueous solutions were prepared for these experiments: (i) a synthetic using Cu-nitrate salt with 0.01 M NaNO₃ and (ii) soil solution obtained from a Cu-contaminated soil using 0.01 M CaCl₂ leaching procedure. Batch sorption and column experiments were used to evaluate the efficiency of both biochar (BC) and activated biochar (BC_act) to remove Cu from the solutions.Results showed that both biochar samples are pure amorphous carbon and the Cu sorption is thus mainly a result of physical sorption on the biochar surface. Next, chemical activation, using 2 M KOH, significantly increased the total volume of all pores in biochar (from 0.01 ± 0.002 to 8.74 ± 0.18 mL g⁻¹). On the other hand, the BET surface area was similar for both sorbents (BC = 9.80 ± 0.62 m² g⁻¹ and BC_act = 11.6 ± 0.4 m² g⁻¹). Results also demonstrate enhanced sorption efficiency of the BC_act (10.3 mg g⁻¹) in comparison with the BC (8.77 mg g⁻¹). Additionally, enhanced Cu removal during column retention test was observed for the BC_act in both synthetic and soil solutions, respectively.In summary, the results showed that biochar prepared from brewers draff was able to remove Cu from both aqueous solutions.     

Effect of hydrogen-sulfide on the hydrogen permeance of palladium–copper alloys at elevated temperatures

The hydrogen permeance of several 0.1 mm thick Pd–Cu alloy foils (80 wt.% Pd–20 wt.% Cu, 60 wt.% Pd–40 wt.% Cu and 53 wt.% Pd–47 wt.% Cu) was evaluated using transient flux measurements at temperatures ranging from 603 to 1123 K and pressures up to 620 kPa both in the presence and absence of 1000 ppm H₂S. Sulfur resistance, as evidenced by no significant change in permeance, was correlated with the temperatures associated with the face-centered-cubic crystalline structure for the alloys in this study. The permeance of the body-centered cubic phase, however, was up to two orders of magnitude lower when exposed to H₂S. A smooth transition from sulfur poisoning to sulfur resistance with increasing temperature was correlated with the alloy transition from a body-centered-cubic structure to a face-centered-cubic structure.     

Carboxylic-supported copper complexes as catalyst for the green oxidative coupling of 2,6-dimethylphenol: Synthesis,characterization and structure

Three new Cu(II) complexes with carboxylic ligand, namely {[Cu(qc)₂(py)]·4H₂O}_∞ (1), [Cu(qc)₂(4,4′-bpy)]_∞ (2) and [Cu(pc)(2,2′-bpy)(H₂O)]₂·H₂O (3) (Hqc = 3-hydroxy-2-quinoxalinecarboxylic acid, H₂pc = 4-hydroxyphthalic acid, py = pyrazine) have been synthesized and characterized. In both 1 and 2, each Cu(II) ion is coordinated by two quinoxalinecarboxylate moieties in the equatorial plane and two 4,4′-bpy or pyrazine units provide coordination in the axial positions, thus, resulting in a 1-D polymeric chain structure. Complex 3 has a dimeric structure in which two Cu(II) cations are bridged by two deprotonated pc^2? ligands and two 2,2′-bpy molecules. As heterogeneous catalysts, the title complexes showed high catalytic efficiency in the green oxidative polymerization of 2,6-dimethylphenol (DMP) to poly(1,4-phenylene ether) (PPE) in the presence of H₂O₂ as oxidant in water under mild conditions. Moreover, they allow reuse without significant loss of activity through four runs, which suggests that these catalysts are efficient, mild, and easily recyclable for the oxidative coupling of DMP. The preliminary study of the catalytic–structural correlations suggests that the coordination environment of the metal center plays an important role in the improvement of their catalytic efficiencies.     

Properties of low power spark ablation in aqueous solution for dissolution of precious metals and alloys

Spark ablation or electric dispersion of metal samples in aqueous solution can be a useful approach for sample preparation. The ablated metal forms a stable suspension that has been described as colloidal, which is easily dissolved with a small amount of concentrated (16 M) HNO₃. In this study, we have examined some of the properties of the spark ablation process for a variety of metals (Rh and Au) and alloys (stainless steel) using a low power spark (100–300 W). Particle size distributions and conductivity measurements were carried out on selected metals to characterize the stable suspensions. A LASER diffraction particle size analyzer was useful for showing that ablated particles varied in size from 1 to 30 μm for both the silver and the nickel alloy, Inconel. In terms of weight percent most of the particles were between 10 and 30 μm. Conductivity of the spark ablation solution was found to increase linearly for approximately 3 min before leveling off at approximately 300 S cm³. These measurements suggest that a significant portion of the ablated metal is also ionic in nature. Scanning electron microscope measurements revealed that a low power spark is much less damaging to the metal surface than a high power spark. Crater formation of the low power spark was found in a wider area than expected with the highest concentration where the spark was directed. The feasibility of using spark ablation for metal dissolution of a valuable artifact such as gold was also performed. Determinations of Ag (4–12%) and Cu (1–3%) in Bullion Reference Material (BRM) gave results that were in very good agreement with the certified values. The precision was ± 0.27% for Ag at 4.15% (RSD = 6.5%) and ± 0.09% for Cu at 1% (RSD = 9.0%).     

Synthesis,crystal structure,and magnetic properties of a copper(II) octacyanotungstate(V)-based magnet containing two types of organic ligands

Cu₃[W(CN)₈]₂(pyrimidine)₂(3-cyanopyridine)₂ · 4H₂O, a cyanide-bridged copper(II) octacyanotungstate(V) with two types of organic ligands (pyrimidine and 3-cyanopyridine), is prepared. In this compound, the coordination geometry of W is an 8-coordinated bicapped trigonal prism where five CN groups of [W(CN)₈] are bridged to five Cu ions, and the remaining three CN groups are free. The coordination geometries of the three types of Cu ions (Cu1, Cu2, and Cu3) are 6-coordinated pseudo-octahedron. The cyano-bridged-Cu2–W–Cu3-layer is linked by a Cu1 pillar unit, and a cavity along the a axis, which is occupied by 3-cyanopyridine molecules and zeolitic water molecules, exists. The present compound shows ferrimagnetism with a Currie temperature of 7 K, a saturation magnetization of 2.9 μ_B, and a coercive field of 7 Oe at 2 K.     

Photocatalytic activity of nitrogen and copper doped TiO2 nanoparticles prepared by microwave-assisted sol-gel process

Cu and N-doped TiO₂ photocatalysts were synthesized from titanium (IV) isopropoxide via a microwave-assisted sol-gel method. The synthesized materials were characterized by X-ray diffraction, UV-vis diffuse reflectance, photoluminescence (PL) spectroscopy, SEM, TEM, FT-IR, Raman spectroscopy, photocurrent measurement technique, and nitrogen adsorption–desorption isotherms. Raman spectra and XRD showed an anatase phase structure. The SEM and TEM images revealed the formation of an almost spheroid mono disperse TiO₂ with particle sizes in the range of 9-17 nm. Analysis of N₂ isotherm measurements showed that all investigated TiO₂ samples have mesoporous structures with high surface areas. The optical absorption edge for the doped TiO₂ was significantly shifted to the visible light region. The photocurrent and photocatalytic activity of pure and doped TiO₂ were evaluated with the degradation of methyl orange (MO) and methylene blue (MB) solution under both UV and visible light illumination. The doped TiO₂ nanoparticles exhibit higher catalytic activity under each of visible light and UV irradiation in contrast to pure TiO₂. The photocatalytic activity and photocurrent ability of TiO₂ have been enhanced by doping of the titania in the following order: (Cu, N) - codoped TiO₂ > N-doped TiO₂ > Cu-doped TiO₂ > TiO₂. COD result for (Cu, N)-codoped TiO₂ reveals ∼92% mineralization of the MO dye on six h of visible light irradiation.     

Simultaneous removal of copper(II), lead(II), zinc(II) and cadmium(II) from aqueous solutions by multi-walled carbon nanotubes

Multi-walled carbon nanotubes (MWCNTs) were used successfully for the removal of heavy metals from aqueous solution. Characterization techniques showed the carbon as nanotubes with an average diameter between 40 and 60 nm and a specific surface area of 61.5 m² g^?1. The effect of carbon nanotubes mass, contact time, metal ions concentration, solution pH, and ionic strength on the adsorption of Cu(II), Pb(II), Cd(II) and Zn(II) by MWCNTs were studied and optimized. The adsorption of the heavy metals from aqueous solution by MWCNTs was studied kinetically using different kinetic models. A pseudo-second order model and the Elovich model were found to be in good agreement with the experimental data. The mechanism of adsorption was studied by the intra-particle diffusion model, and the results showed that intra-particle diffusion was not the slowest of the rate processes that determined the overall order. This model also revealed that the interaction of the metal ions with the MWCNTs surface might have been the most significant rate process. There was a competition among the metal ions for binding of the active sites present on the MWCNTs surface with affinity in the following order: Cu(II) > Zn(II) > Pb(II) > Cd(II).