染料在纳米TiO2薄膜表面吸附性能的研究

采用溶胶－凝胶法制备纳米TiO2薄膜，并通过吸附染料形成染料／TiO2复合薄膜。分析了染料与TiO2薄膜的相互关系，利用紫外可见、比表面等技术研究染料在纳米TiO2薄膜表面的吸附性能，并计算出TiO2薄膜对染料的最大吸附率。研究表明，染料溶液浓度、温度以及TiO2薄膜浸泡时间对染料吸附量有着显著的影响，染料的吸附性能直接影响着太阳能电池的光电转换效率。     

吸附聚丙烯酸对纳米碳管表面特征影响的研究

利用低温氮气吸附法系统研究了吸附聚丙烯酸 (PAA)的量对纳米碳管表面特征的影响 .分析结果表明 :当PAA吸附量增加到 2 68 98mg·g-1时 ,纳米碳管的比表面积下降了 46 97% ;虽然吸附PAA后的纳米碳管在 1 8nm以上的孔径分布特征基本上与原样一致 ,但孔容减少 ,这部分孔对比表面的贡献明显降低 ,同时出现 1 8nm以下的孔 ;通过氮气吸附等温线利用热力学方法计算的纳米碳管的表面分维值 (surfacefractaldimension)dSF由原样的 2 5 4下降至吸附后的 2 48,表明吸附PAA分子能够降低纳米碳管的粗糙度 .这些说明堵孔效应和屏蔽效应是纳米碳管表面特征改变的主要因素 ,这一研究对纳米碳管在吸附、催化等方面的应用有着非常重要的意义 .     

TiO2/聚丙烯酸丁酯纳米复合薄膜的制备及结构表征

利用微乳液原位聚合法在普通玻璃表面上制备了TiO2/聚丙烯酸丁酯纳米复合膜.采用傅立叶变换红外光谱、高分辨透射电子显微镜和X射线光电子能谱对膜的结构进行了表征.结果表明， TiO2以纳米线的形式弥散在聚丙烯酸丁酯的高分子网络中，并且所制备的TiO2纳米线具有板钛矿相结构.     

流动注射分析在线研究Cr（Ⅵ）在纳米TiO2表面上的吸附 …

用溶胶－凝聚法在不同的水解和热处理条件下制备了纳米尺寸的ＴｉＯ２微粉，所得的ＴｉＯ２表面性质迥异，粒径从几个纳米到数百个纳米，晶型也由低温煅烧的锐钛型转成高温地的金红石型。利用流动注射微柱富集在线分析方法对Ｃｒ离子在纳米ＴｉＯ２表面上的吸附动力学特性进行了原位表征。     

TiO2/聚丙烯酸丁酯纳米复合膜的制备及摩擦性能

二氧化钛;TiO2/聚丙烯酸丁酯纳米复合膜的制备及摩擦性能     

硼氢化钾还原-原子荧光光谱法研究纳米TiO2对Hg(Ⅱ)的吸附行为

以硼氢化钾还原-原子荧光光谱法(KBH4-AFS)为检测手段，研究了纳米TiO2(锐钛型)对Hg(Ⅱ)的吸附行为，考察了影响吸附和解脱的主要因素，并考察了共存离子的干扰影响。在较宽的pH范围内，纳米TiO2对汞具有良好的吸附性能。在优化的实验条件下，具有吸附容量较大和吸附速度较快的特点，该法测定汞的检出限为0．004ng/mL，相对标准偏差(RSD)为3．3％(n=9，ρ=0．05ng/mL)。将本法应用于标准样品GSS-8、GSS-4的测定，其测定值与标准值吻合。已应用于实际水样中汞的测定。     

用分子轨道理论研究NO气体在TiO2表面吸附

根据一氧化氮(NO)气体在二氧化钛(TiO)表面吸附和脱附的实验结果,揭示了气体脱附量的变化规律．利用MOPAC和GAUSSIAN分子轨道理论计算了在TiO2(110)表面上吸附NO分子的原子簇模型,电荷分布以及原子簇的能级,推断了NO在TiO(110)表面吸附的稳定性．     

微波法制备纳米TiO2

国内外合成纳米TiO2的方法很多。微波加热法与常规方法相比反应速率快、效率高,并适合推广到大规模的工业生产中。本研究工作以Ti(SO4)2为主要原料,在Ti(SO4)2的水解反应中引入微波加热技术,系统地研究了其制备工艺条件,为纳米TiO2微粒的制备开辟一条新路。     

壳聚糖/聚丙烯酸纳米粒子对蛋白质的吸附行为

以马来酸酐改性的壳聚糖(MAH-chitosan)和丙烯酸(AA)为单体,采用反相微乳液聚合法制备了AA含量分别为77%(AA-Cs)和29%(Cs-AA)壳聚糖/聚丙烯酸复合纳米粒子。TEM结果表明,该复合纳米粒子平均粒径为125~150nm,进而研究了其对牛血红蛋白(Hb)、牛血清白蛋白(BSA)和溶菌酶(Ly)吸附和脱附行为。AA-Cs对各种蛋白的吸附量均较高;而Cs-AA对3种蛋白的吸附则具有一定选择性。AA-Cs对等电点低于脱附pH值的Hb的脱附量较大。Cs-AA粒子在较低pH值(pH=3.4)时对吸附有利,但在高pH值(pH=6.6)进行吸附时,对脱附更为有利。     

密度泛函理论研究CO和 O2在NiFeB2/TiO2表面的吸附

 运用密度泛函理论中广义梯度近似的 PW91 方法结合周期平板模型, 研究了 NiFeB2 合金簇在 TiO2(110) 面的吸附模式. 结果表明, NiFeB2 平行吸附在 TiO2 面的 Ot-Ot 位最稳定, 吸附能为 526.4 kJ/mol. 为了探明 NiFeB2/TiO2 是否具有催化氧化 CO 活性, 进一步研究了 CO 和 O2 在 NiFeB2/TiO2 面的共吸附行为. 结果表明, CO 和 O2 以 Eley-Rideal 机理共吸附在 Fe 上时, 易形成碳酸盐, 而以 Langmuir-Hinshelwood 机理共吸附在 Fe 上时, O2 发生分解, 与 Fe, Ni 和 B 形成稳定的六元环.     

Photo-grafting Poly(acrylic acid) onto Poly(lactic acid) Chains in Solution

Poly(lactic acid)(PLA)is one of the most important bio-plastics,and chemical modification of the already-polymerized poly(lactic acid)chains may enable optimization of its material properties and expand its application areas.In this study,we demonstrated that poly(lactic acid)can be readily dissolved in acrylic acid at room temperature,and acrylic acid can be graft-polymerized onto poly(lactic acid)chains in solution with the help of photoinitiator benzophenone under 254 nm ultraviolet(UV)irradiation.Similar photo-grafting polymerization of acrylic acid(PAA)has only been studied before in the surface modification of polymer films.The graft ratio could be controlled by various reaction parameters,including irradiation time,benzophenone content,and monomer/polymer ratios.This photo-grafting reaction resulted in high graft ratio(graft ratio PAA/PLA up to 180%)without formation of homopolymers of acrylic acid.When the PAA/PLA graft ratio was higher than 100%,the resulting PLA-g-PAA polymer was found dispersible in water.The pros and cons of the photo-grafting reaction were also discussed.     

用超临界CO2制备疏水改性聚丙烯酸

用超临界CO2制备疏水改性聚丙烯酸;丙烯酸十八酯;超临界二氧化碳;疏水缔合     

聚乙烯醇多孔膜的制备及其对二氧化钛的负载研究

以聚乙烯醇(PVA)为聚合物基体,戊二醛为交联剂,乙酸为催化剂,聚乙二醇6000(PEG-6000)为致孔剂,制备了聚乙烯醇多孔膜(porous PVA films,PPF多孔膜);再将实验室自制的二氧化钛溶胶(TiO_2)负载于PPF多孔膜上,制备得到聚乙烯醇原位负载二氧化钛功能薄膜(PPF-TiO_2)。采用红外光谱、扫描电镜、分光光度计等分别考察了PPF多孔膜的交联条件、负载前后PPF-TiO_2功能薄膜的形貌,PPF-TiO_2功能薄膜对甲基橙的去除率。研究结果表明,为制备适宜交联度及孔径的PPF多孔膜,戊二醛浓度为5%(wt),PEG-6000用量为PVA用量的0.6倍为宜;PPF多孔膜对TiO_2负载的温度为40℃,负载时间为2h能够获得负载量为43%的PPF-TiO_2功能薄膜。此外,PPF-TiO_2功能薄膜比商品化TiO_2对甲基橙的降解率(100mg/L)更快,且具有可循环使用的优势。     

pH-effects in the complex formation of polymers I. Interaction of poly(acrylic acid) with poly(acrylamide)

The effects of polymer concentration, molecular weight of poly(acrylic acid) (PAA), addition of sodium, potassium, ammonium and copper (II) chlorides on the complex formation ability of the system PAA-poly(acrylamide) (PAAM) have been studied in aqueous solutions. The critical pH values of the complexation were determined in different conditions. The complex formation ability of PAAM is compared with other non-ionic polymers. It was shown that an increase in polymers concentration, molecular weight of PAA and ionic strength favours the complexation and shifts the critical pH values to the higher pH region. An addition of CuCl₂ to the mixture of two polymers enhances the complexation drastically due to the formation of triple complexes.     

阳离子和两性表面活性剂在聚甲基丙烯酸甲酯表面的吸附行为

利用座滴法研究了阳离子表面活性剂十六烷基醚羟丙基季铵盐(C₁₆PC)、十六烷基聚氧乙烯醚羟丙基季铵盐(C₁₆(EO)₃PC)和两性离子表面活性剂十六烷基醚羟丙基羧酸甜菜碱(C₁₆PB)、十六烷基聚氧乙烯醚羟丙基羧酸甜菜碱(C₁₆(EO)₃PB)溶液在聚甲基丙烯酸甲酯(PMMA)表面上的润湿性质, 考察了表面活性剂类型及浓度对接触角的影响趋势. 研究发现: 低浓度条件下表面活性剂分子可能以平躺的方式吸附到固体界面, 且亲水基团靠近固体界面, PMMA表面被轻微疏水化; 在高浓度时则通过Lifshitz-van der Waals 作用吸附, 亲水基团在外, PMMA表面被亲水改性. 聚氧乙烯基团(EO基团)的引入对阳离子表面活性剂的接触角影响不大; 而含有聚氧乙烯基团的两性离子表面活性剂在PMMA界面上以类似半胶束的聚集体吸附, 大幅度降低接触角.     

Preparation and characterization of poly(acrylic acid)-based nanoparticles

The present investigation describes the synthesis and characterization of nanoparticles based on poly(acrylic acid) (PAA) intramolecularly cross-linked with diamine, 2,2′-(ethylenedioxy)bis(ethylamine), using water-soluble carbodiimide. The aqueous colloid dispersions of nanoparticles were clear or mildly opalescent depending on the ratio of cross-linking, pH of the solution, and the molecular weight of PAA, finding consistent with values of transmittance between 3% and 99%. The structure was determined by nuclear magnetic resonance spectroscopy, and the particle size was identified by dynamic light scattering (DLS) and transmission electron microscopy (TEM) measurements. It was found that particle size depends on the pH, and at a given pH, it was caused by the ratio of cross-linking and the molecular weight of PAA. Particle size measured by TEM varied in the range of 20 and 80 nm. In the swollen state, the average size of the particles measured by DLS was in the range of 35–160 nm.     

Binding of a surfactant counterion to low-charge-density poly(acrylic acid) and poly(methacrylic acid)

The binding of a cationic surfactant, dodecylpyridinium (C12Py) chloride, with a low-charge-density poly (methacrylic acid) (PMA) was investigated in buffer solutions under the condition of constant pH. The binding isotherms with PMA consisted of two and three steps at a pH lower and higher than 3.2, respectively. Bindings in the first step were independent of pH and this step was considered to correspond to the solubilization of the hydrocarbon chains of C12Py into the nonpolar region of the compact form of PMA. This is the indication of the compact form from the binding isotherm. At pH higher than 3.2, the second step was discriminated and it depended on the pH. In the third step, a sharp rise in the degree of binding (β) was observed accompanying the solubilization of the precipitates of the PMA–C12Py complex. The binding with poly(acrylic acid) (PAA) and PMA in conventional unbuffered NaCl solutions was also examined and the pH profile of the solution during the binding process was determined. In the case of unbuffered NaCl solutions, the binding with PAA took place cooperatively at the critical association concentration (cac). The binding isotherm consisted of two steps and the pH decreased with the increase in β. The binding isotherm of PMA, on the other hand, consisted of three steps: the pH decreased slightly in the first step and considerably in the second step with the increase in β but it increased with β in the third step, exhibiting a pH minimum around 3.2. The binding in the first step coincided with that obtained in the buffered solutions. Linear relationships between β and the pH were found for both polymers. In the case of PMA, no cac was observed in both buffered and unbuffered NaCl solutions. Received: 24 January 2001 Accepted: 23 May 2001     

Production of Poly(acrylic acid) Particles Dispersed in Organic Media

Summary: A process for preparation of poly(acrylic acid) particles dispersed in oil is presented. The process comprises two steps: the first step involves the preparation of a poly(acrylic acid) solution, while the second step consists in the preparation of the polymer particles by dispersing the polymer solution in an organic phase. During the second step, modification of the polymer chain structure can be performed through chemical reactions. One of the advantages of the proposed process is the possibility to produce particles loaded with drugs or other chemical compounds. Besides that, if the continuous phase is vegetable oil, purification of the reaction medium may not be necessary.     

聚丙烯酸功能化多壁碳纳米管

Covalent functionalization of multiwalled carbon nanotubes （MWNT） with poly（acrylic acid） has been successfully achieved via grafting of poly（acryloyl chloride） on nanotube surface by esterification reaction of acyl chloride-bound polymer with hydroxyl functional groups present on acid-oxidized MWNT and hydrolysis of polymer attached to nanotubes. Polymer-functionalized MWNT could possess remarkably high solubility in water, and their aqueous solution was very stable without any observable black deposit for a long time. Characterizations of such functionalized MWNT samples using Fourier transform infrared spectrometer, transmission electron microscopy and nuclear magnetic resonance techniques indicated that poly（acrylic acid） was covalently attached to the surface of MWNT.     

Poly (acrylic acid) microchannel modification for the enhanced resolution of catecholamines microchip electrophoresis with electrochemical detection

A new modification of glass electrophoresis microchips based on poly (acrylic) acid immobilization has been performed. It is based on the reaction of PAA with an amine functionalized surface, obtained through the bifunctional reagent 3-aminopropyl triethoxysilane. Parameters affecting all the three steps involved: surface activation, silanization and polymer immobilization were optimized employing soda-lime glass plates. Characterization by SEM and XPS was carried out. Application of the modified microchips to the separation of a model system: dopamine (D), epinephrine (E) and norepinephrine (NE), that on the other hand are of high clinical relevance was performed employing amperometric detection. Modification is necessary for obtaining partial resolution of all the three analytes in a microchip with an effective separation length of 30 mm. Situation changes from no resolution (Rs) at all (only one peak was achieved for the mixture) to a partial resolution (Rs D–NE and Rs NE–E are 0.25 and 0.24 respectively). Microchips with 60 mm of separation channel were also modified, implying this procedure a resolution enhancement (Rs of 0.49 and 0.28 for D–NE and NE–E respectively), even when methanol is employed as organic modifier (Rs values of 0.70 (D–NE) and 0.66 (NE–E) for a 3% MeOH).