Miscibility,morphology and fracture toughness of epoxy resin/poly(vinyl acetate) blends

Diglycidylether of bisphenol A (DGEBA)/poly(vinyl acetate) (PVAc) blends cured with 4,4-diaminodiphenylmethane (DDM) were prepared. The miscibility and phase behavior were investigated by means of differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and scanning electron microscopy (SEM). The study results indicate that the epoxy precursor (DGEBA)/PVAc blends are clearly miscible at the entire composition and theTg values experimentally obtained are in a good agreement with those predicted by Fox equation. Cured at elevated temperature, all the DDM-cured blends underwent phase separation and display two-phase morphology. When PVAc content is more than 10 wt%, the thermoplastics-modified resins began to show a co-continuous phase structure. It is the cocontinuous structure that leads to a significantly-improved toughness inK _ic. Morphologic investigation of the surfaces of fracture mechanic measurement specimens indicates that the toughening effect of the thermoplastics-modified epoxy resins may arise mainly from the ductile yielding of PVAc.     

Reactive compatibilization of epoxy/polyorganosiloxane blends

A new thermoset material based on DGEBA with polyaminosiloxane curing agents is presented. The system shows reaction-induced compatibilization which prevents coalescence of polysiloxane and DGEBA rich domains, leading to gradient structured morphologies. The influence of curing temperature and/or chemical nature of the siloxane on the morphology and surface microhardness were examined. When siloxane is pre-reacted with epoxypropylphenylether (EPPE), a more homogeneous material is obtained. Microhardness profiles on the material are strongly influenced by the extension of the compositional gradients.     

Study on the chemical modification of epoxy/anhydride thermosets using a hydroxyl terminated hyperbranched polymer

Mixtures of diglycidylether of bisphenol A (DGEBA) resin and commercially available hyperbranched polyester (HBP) Boltorn H30 were cured by anhydride to covalently bond the hydroxyl end groups in HBP with the epoxy resin. The curing mixtures were investigated by Differential Scanning Calorimetry (DSC) to study the curing evolution and to evaluate the kinetic parameters. DSC studies suggested that HBP could increase the curing rate of epoxy/anhydride systems at low conversions, but it produced a decelerative effect in the last stages of the curing. The influence of the HBP content and the proportion of anhydride on the curing conversions were discussed in detail. The addition of a tertiary amine was proved to decrease the curing temperatures. By Fourier Transform Infrared Spectroscopy (FTIR) the reaction of hydroxyl groups during the whole process was confirmed. By the determination of the conversion at the gelation, we could prove that it increased on increasing the proportion of HBP in the reactive mixture. By Thermomechanical Analysis (TMA) we could determine a reduction of the shrinkage after gelation.     

Study of the structure and the mechanical properties of dynamically cured PP/MAH-g-SEBS/epoxy blends

A new method concerning with the simultaneous reinforcing and toughening of polypropylene(PP) was reported.Dynamical cure of the epoxy resin was successfully applied in the PP/maleic anhydride-grafted styrene-ethylene-butylene-styrene(SEBS) triblock copolymer,and the obtained blends named as dynamically cured PP/MAH-g-SEBS/epoxy blends.The stiffness and toughness of the blends are in a good balance,and MAH-g-SEBS was acted as not only an impact modifier but also a compatibilizer. The structure of the dyn...     

Curing behavior and properties of high biosourced epoxy resin blends based on a triepoxy monomer and a tricarboxylic acid hardener from 10-undecenoic acid

Renewable propane-1,2,3-triyl tris(9-(oxiran-2-yl) nonanoate) (EGU, 100 wt% biogenic) and a tricarboxylic acid triglyceride (CGTU) hardener (85.7 wt% biogenic) were synthesized from 10-undecenoic acid (10-UDA) and used to produce epoxy resins with 52–92 wt% biobased carbon. CGTU was prepared by thermally activated thiol-ene coupling of thioglycolic acid onto propane-1,2,3-triyl tris(undec-10-enoate), (GUD) in the absence of solvent. The characterized CGTU was used as a green hardener of blends based on EGU and a conventional bisphenol A-based epoxy pre-polymer (DGEBA) at various mass percentages (0–100 wt%) with an stoichiometric epoxy/acid equivalent ratio. Calorimetric studies revealed higher peak temperature, lower reaction heats, and longer gelation times in resins with high EGU proportion, evidencing the lower reactivity of aliphatic EGU compared with aromatic DGEBA. Cured resins were yellowish transparent rubber-like materials with glass transition temperatures (Tg) varying from −14 °C to −42 °C and tensile strength in the range of 1750 kPa–790 kPa, for 0 and 100 wt % EGU, respectively. The soluble fraction of all resins was less than 4.3%, reflecting a high level of crosslinking. Thermosets with high biobased content showed both UV-light protection and visible light transparency.     

Thermal-oxidative aging of DGEBA/EPN/LMPA epoxy system: Chemical structure and thermal-mechanical properties

The evolvement of chemical structure and thermal-mechanical properties of diglycidyl ether of bisphenol-A and novolac epoxy resin blends cured with low molecular polyamide (DGEBA/EPN/LMPA system) during thermal-oxidative aging were investigated by Attenuated Total Reflectance Fourier Transform Infrared spectrometry (ATR-FTIR) and Dynamic Mechanical Thermal Analysis (DMTA). The results revealed that the chemical reactions during thermal-oxidative aging contained oxidation and chain scission. Some possible chemical reaction processes were given. There was a new compound formed during aging processes and the change of its glass transition temperature (T_g) with aging time followed an exponential law. In addition, the changes of dynamic mechanical behavior of this epoxy system aged at four different temperatures (110 °C, 130 °C, 150 °C, 170 °C) were compared. An empirical formula was obtained through kinetic analysis and this formula can be used to predict the oxidative degree of the surface at different aging temperature.     

Organic/inorganic hybrid epoxy nanocomposites based on octa(aminophenyl)silsesquioxane

Octa(aminophenyl)silsesquioxane (OAPS) was used as the curing agent of diglycidyl ether of bisphenol-A (DGEBA) epoxy resin. A study on comparison of DGEBA/OAPS with DGEBA/4,4′-diaminodiphenyl sulfone (DDS) epoxy resins was achieved. Differential scanning calorimetry was used to investigate the curing reaction and its kinetics, and the glass transition of DGEBA/OAPS. Thermogravimetric analysis was used to investigate thermal decomposition of the two kinds of epoxy resins. The reactions between amino groups and epoxy groups were investigated using Fourier transform infrared spectroscopy. Scanning electron microscopy was used to observe morphology of the two epoxy resins. The results indicated that OAPS had very good compatibility with DGEBA in molecular level, and could form a transparent DGEBA/OAPS resin. The curing reaction of the DGEBA/OAPS prepolymer could occur under low temperatures compared with DGEBA/DDS. The DGEBA/OAPS resin didn’t exhibit glass transition, but the DGEBA/DDS did, which meant that the large cage structure of OAPS limited the motion of chains between the cross-linking points. Measurements of the contact angle indicated that the DGEBA/OAPS showed larger angles with water than the DGEBA/DDS resin. Thermogravimetric analysis indicated that the incorporation of OAPS into epoxy system resulted in low mass loss rate and high char yield, but its initial decomposition temperature seemed to be lowered.     

Raman investigation of thermoplastic vulcanizates based on hydrogenated natural rubber/polypropylene blends

Raman spectroscopy including mapping technique appears as a powerful technique for the characterization of polymer blends like thermoplastic elastomers (TPEs) and thermoplastic vulcanizates (TPVs). The Raman spectra of polymers blends such as natural rubber/polypropylene (NR/PP) and 65% hydrogenated natural rubber/polypropylene (65%HNR/PP) were identified and the phase distribution was determined. The study was driven for the same type of blends in TPEs state and TPVs state obtained after to 2 different processes, either peroxide cure or sulfur cure. The morphology of TPEs and TPVs obtained by Raman spectroscopy were compared and confirmed using scanning electronic microscopy.Raman mapping shows that the phase morphology of NR/PP, 65%HNR/PP, were characterized as continuous rubber phase morphology of the thermoplastic elastomers (TPEs) and a fine dispersion of cross-linked rubber phase in a continuous matrix of the thermoplastic vulcanizates (TPVs). Raman spectroscopy is demonstrated to be a reference to determine the content ratio of each component in the TPVs. Moreover, Raman mapping could be used to calculate the phase size of cross-linked rubber phase dispersed in the thermoplastic vulcanizates (TPVs).     

Hydrogen bonding interactions,crystallization, and surface hydrophobicity in nanostructured epoxy/block copolymer blends

Hydrogen bonding interactions, phase behavior, crystallization, and surface hydrophobicity in nanostructured blend of bisphenol A‐type epoxy resin (ER), for example, diglycidyl ether of bisphenol A (DGEBA) and poly(ε‐caprolactone)‐block‐poly(dimethyl siloxane)‐block‐poly(ε‐caprolactone) (PCL–PDMS–PCL) triblock copolymer were investigated by Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry, transmission electron microscopy, small‐angle X‐ray scattering, and contact angle measurements. The PCL–PDMS–PCL triblock copolymer consisted of two epoxy‐miscible PCL blocks and an epoxy‐immiscible PDMS block. The cured ER/PCL–PDMS–PCL blends showed composition‐dependent nanostructures from spherical and worm‐like microdomains to lamellar morphology. FTIR study revealed the existence of hydrogen bonding interactions between the PCL blocks and the cured epoxy, which was responsible for their miscibility. The overall crystallization rate of the PCL blocks in the blend decreased remarkably with increasing ER content, whereas the melting point was slightly depressed in the blends. The surface hydrophobicity of the cured ER increased upon addition of the block copolymer, whereas the surface free energy (γ_s) values decreased with increasing block copolymer concentration. The hydrophilicity of the epoxy could be reduced through blending with the PCL–PDMS–PCL block copolymer that contained a hydrophobic PDMS block. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 790–800, 2010     

Thermal properties of epoxy resin nanocomposites based on hydrotalcites

Epoxy resin nanocomposites containing home-made hydrotalcites (HTlc) have been prepared and their properties have been studied and compared with those of montmorillonite (MMT)-type layered silicates-based nanocomposites. Nanofiller dispersion in the polymer matrix has been evaluated by transmission (TEM) electron microscopy and wide angle X-ray diffraction (WAXD), while nanocomposite thermal properties have been studied in detail by thermogravimetric analysis (TGA/DTG) and cone calorimeter tests.The morphological studies have shown that the compatibilisation of the above two type of nanofillers allowed us to obtain nanostructured materials. As far as thermal properties are concerned, nanocomposites based on HTlc are found to decompose, both in air and nitrogen, following a trend similar to that of the neat polymer matrix, while in the case of the nanocomposite based on the organophilic MMT a slight improvement was found in air. Conversely, cone calorimetric tests have demonstrated that only the organophilic hydrotalcite was capable of decreasing the peak of the heat release rate in a relevant way.     

Flame retardant epoxy polymers based on all phosphorus-containing components

A phosphorus-containing epoxy resin, bis(3-t-butyl-4-glycidyloxyphenyl-2,4-di-t-butylphenyl)resorcinol diphosphate, was synthesized and subsequently cured with non-phosphorus containing amines, and/or novel phosphorus-containing aromatic or polyoxyalkylene amines. Chemical structures of these materials were characterized with FTIR, NMR, elemental analysis, and amine titration. The introduction of soft -P-O- linkage, polyoxyalkyene, or hard aromatic group into the backbones of the synthesized phosphorus-containing amines provides epoxy polymers with high phosphorus contents and tailored flexibility. Thermal analysis of differential scanning calorimeter and thermal gravimetric analysis (TGA) reveals that these resulted epoxy polymers possess moderate T_gs and thermal stability. Furthermore, high char yields in TGA analysis and high limited oxygen index values indicate that these phosphorus-containing epoxy polymers possess excellent flame retardant properties.     

Mechanical properties of polymer composites based on commercial epoxy vinyl ester resin and glass fiber

The effect of the addition of methyl ethyl ketone peroxide (MEKP) and cobalt naphthenate (CoNaph) on the mechanical behavior of epoxy vinyl ester resin (EVER) laminates has been investigated by using a factorial experimental design, in which the MEKP and NaphCo contents were varied. Previous results showed that there is an interaction effect between the process variables analysed on the mechanical properties evaluated. It was also observed that the MEKP/CoNaph ratio affected the tensile behavior of the EVER/glass fiber composites.     

The non-halogen flame retardant epoxy resin based on a novel compound with phosphaphenanthrene and cyclotriphosphazene double functional groups

A novel flame retardant additive hexa-(phosphaphenanthrene -hydroxyl-methyl-phenoxyl)-cyclotriphosphazene (HAP-DOPO) with phosphazene and phosphaphenanthrene double functional groups has been synthesized from hexa-chloro-cyclotriphosphazene, 4-hydroxy-benzaldehyde and 9,10-dihydro-9-oxa-10- phosphaphenanthrene 10-oxide(DOPO). The structure of HAP-DOPO was characterized by Fourier transformed infrared (FT-IR) spectroscopy and ¹H nuclear magnetic resonance (¹H NMR) and ³¹P nuclear magnetic resonance (³¹P NMR). The additive HAP-DOPO was blended into diglycidyl ether of bisphenol-A (DGEBA) to prepare flame retardant epoxy resins. The flame retardant properties and thermal properties of the epoxy resins cured by 4, 4′-Diamino-diphenyl sulfone (DDS) were investigated from the differential scanning calorimeter (DSC), the thermogravimetric analysis (TGA), UL94 test, the limiting oxygen index (LOI) test and Cone calorimeter. Compared to traditional DOPO-DGEBA and ODOPB-DGEBA thermosets, the HAP-DOPO/DGEBA thermosets have higher T_gs at the same UL94 V-0 flammability rating for their higher crosslinking density and have higher char yield and lower pk-HRR at same 1.2 wt.% phosphorus content which confirm that HAP-DOPO has higher flame retardant efficiency on thermosets. The scanning electron microscopy (SEM) results shows that HAP-DOPO in DGEBA/DDS system obviously accelerate formation of the sealing, stronger and phosphorus-rich char layer to improve flame retardant properties of matrix during combustion.     

Effect of aromatic substitution on the cure reaction and network properties of anhydride cured triphenyl ether tetraglycidyl epoxy resins

A systemic study of the impact of aromatic substitution on the reaction rate and network properties of the isomers of a tetraglycidylaniline triphenyl ether epoxy resin cured with anhydride hardeners is presented here. The epoxy resins synthesized in this work were based upon N,N,N,N‐tetraglycidyl bis(aminophenoxy)benzene (TGAPB), where the glycidyl aniline and ether groups change from being all meta (133 TGAPB), to meta and para (134 TGAPB), and finally to an all para substituted epoxy resin (144 TGAPB). Increasing para substitution increased reaction rate, promoted the onset of vitrification and increased epoxide conversion. Thermal properties such as glass transition temperatures (T_g) and coefficients of thermal expansion (CTE) both increased consistently with increasing para substitution, although thermal stability as measured via thermogravimetric analysis decreased. Mechanical properties also varied systematically with flexural strength and ductility increasing with increased para substitution, while the modulus decreased. Indeed, the ductility almost doubled, as measured by the work of fracture and displacement at failure highlighting the importance of substitution on properties.     

Diglycidyl ether of bisphenol-A epoxy resin–polyether sulfone/polyether sulfone ether ketone blends: phase morphology, fracture toughness and thermo-mechanical properties

The properties of diglycidyl ether of bisphenol-A epoxy resin toughened with poly(ether sulfone ether ketone) (PESEK) and poly(ether sulfone) (PES) polymers were investigated. PESEK was synthesised by the nucleophilic substitution reaction of 4,4’-difluorobenzophenone with dihydroxydiphenylsulfone using sulfolane as solvent and potassium carbonate as catalyst at 230 °C. The T _g–composition behaviour of the homogeneous epoxy resin/PESEK blend was modelled using Fox, Gordon–Taylor and Kelley–Bueche equations. A single relaxation near the glass transition of epoxy resin was observed in all the blend systems. From dynamic mechanical analysis, the crosslink density of the blends was found to decrease with increase in the thermoplastic concentration. The storage modulus of the epoxy/PESEK blends was lower than that of neat resin, whilst it is higher for epoxy/PES blends up to glass transition temperature, thereafter it decreases. Scanning electron microscopic studies of the blends revealed a homogeneous morphology. The homogeneity of the blends was attributed to the similarity in chemical structure of the modifier and the cured epoxy network and due to the H-bonding interactions between the blend components. The fracture toughness of epoxy resin increased on blending with PESEK and PES. The increase in fracture toughness was due to the increase in ductility of the matrix. The thermal stability of the blends was comparable to that of neat epoxy resin.     

环氧树脂共混物相结构的调控方法研究

研究了环氧树脂(E51)/聚砜(PSF)共混物相结构的控制方法.通过抑制相分离、控制预固化的反应程度控制环氧树脂的分子量,固化后可获得不同的共混物相结构.依据红外测定的固化反应程度设定固化程序,可有效控制共混物的相结构.加入促进剂三氟化硼-乙基胺(BTF-EA)可提高固化反应速度,使相分离结构在早期被抑制,以获得小微区的相结构.     

Photodegradation studies of novel biodegradable blends based on poly(ethylene oxide) and pectin

Blends of two biodegradable polymers: natural pectin and synthetic poly(ethylene oxide) at different weight-ratios were obtained by physical mixing in aqueous solutions, and evaporation of the solvent. The macromolecular order in the composites was investigated by applying X-ray diffraction, while the surface morphology was observed using atomic force microscopy. The photooxidative degradation of the blends was studied by viscometry, FTIR spectroscopy and UV-vis spectroscopy. It has been found that the susceptibility of the studied composites to UV radiation depends on an appropriate ratio of components, and the most sensitive to UV-irradiation among the samples studied was the equal weight-ratio blend of poly(ethylene oxide)/pectin.     

Thermal and mechanical properties of polysulfide/epoxy copolymer system: the effect of anhydride content

Polymerization of a ternary system containing polysulfide (PS), as a liquid elastomer, diglycidylether of bisphenol A resin, and phthalic anhydride was conducted using “design of experiment” technique. The polymerization progress with respect to concentration variations of components were studied by Fourier transform infrared spectroscopy. Fourier transform infrared spectroscopy studies showed that the anhydride plays a decisive role in curing reaction so that, in its absence, the epoxy/PS mixture becomes gel in about 2 hr, whereas, by addition of the anhydride, the pot life of the system can be extended to 48 hr. The cured samples were investigated by thermal gravimetry analysis and differential scanning calorimetry to evaluate thermal properties. Thermal gravimetry analysis and differential scanning calorimetry results indicated that two different soft and hard segments are formed, which have different thermal decompositions. The soft segment consists of loose etheric bonds, which are attributed to PS, and the hard segment is formed during the etherification and esterification reactions of the epoxy resin. Tensile strength test was performed to investigate the mechanical properties of PS/epoxy/anhydride‐cured systems. The results showed that the tensile strength, elongation‐at‐break, and the fracture energy of specimens are essentially dependent on PS/anhydride ratios. Two different segments impart high strength and ductility simultaneously. Copyright © 2013 John Wiley & Sons, Ltd.     

Multifunctional nanocomposites based on tetraethylenepentamine-modified graphene oxide/epoxy

Composites based on epoxy/graphene were investigated for thermal-mechanical performance. Initially, few-layer graphene oxide (GO) was modified with tetraethylenepentamine (GO-TEPA) in a reaction assisted by microwave radiation. GO and GO-TEPA samples were characterized for their structure and morphology. Composites containing 0.1, 0.3 and 0.5 wt.% of GO and GO-TEPA were prepared, and the effect of fillers on the morphology of cryofractured regions of epoxy matrix was observed through electron microscopy images. Dynamic mechanical thermal analysis (DMA) tests revealed increases of approximately 20 °C in glass transition. Moreover, when compared to neat polymer, composites containing 0.5 wt.% of GO-TEPA gained up to 103% in thermal conductivity (obtained by flash laser). Finally, nanoindentation analyses showed increases of 72% in Young's modulus and 143% in hardness for the same sample. The system is characterized as multifunctional nanocomposites because of the simultaneous gains in thermal and mechanical properties. The best results of the multifunctional composites were strongly associated with the chemical modification of the GO by TEPA.     

A flame-retardant epoxy resin based on a reactive phosphorus-containing monomer of DODPP and its thermal and flame-retardant properties

A flame-retardant epoxy resin (EP) was synthesized based on a novel reactive phosphorus-containing monomer, 4-[(5,5-dimethyl-2-oxide-1,3,2-dioxaphosphorinan-4-yl)oxy]-phenol (DODPP), and its structures were characterized by FTIR, ¹H NMR and ³¹P NMR spectra. The DODPP-EP₃/LWPA (low molecular weight polyamide), which contains 2.5% phosphorus, can reach UL-94 V-0 rating and a limiting oxygen index (LOI) value of 30.2%. The thermal properties and burning behaviours of cured epoxy resins were investigated by differential scanning calorimeter (DSC), thermogravimetry (TG), LOI, UL-94 tests and cone calorimetry. The morphologies of residues of cured epoxy resins were investigated by scanning electron microscopy (SEM). DSC shows that the glass-transition temperatures of cured epoxy resins decrease with increasing phosphorus content. TGA shows that the onset decomposition temperatures and the maximum-rate decomposition temperatures decrease, while char yields increase, with the increase of phosphorus content. The data from the cone calorimeter tests give the evidence that heat release rate (HRR), peak heat release rate (PHRR), average heat release rate (Av-HRR), average mass loss rate (Av-MLR) and the fire growth rate index (FIGRA) decrease significantly for DODPP-EP₃/LWPA. SEM shows that the DODPP-EP₃/LWPA forms lacunaris and compact charred layers which inhibit the transmission of heat during combustion.