The influence of chitin nanocrystals on structural evolution of ultra-high molecular weight polyethylene/chitin nanocrystal fibers in hot-drawing process

Ultra-high molecular weight polyethylene (UHMWPE)/chitin nanocrystal (CNC) fibers were prepared. Compared with the pure UHMWPE fibers, the ultimate tensile strength and Young’s modulus of UHMWPE/CNC fibers are improved by 15.7% and 49.6%, respectively, with the addition of chitin nanocrystals (CNCs) of 1 wt%. The melting temperature (T _m) of UHMWPE/CNC fibers was higher than that of pure UHMWPE fibers. Pure UHMWPE fibers and UHMWPE/CNC fibers were characterized with respect to crystallinity, orientation and kebab structure by wide-angle X-ray diffraction (WAXD), small-angle X-ray scattering (SAXS) and scanning electron microscopy (SEM). It is found that the CNCs act as the shish structure in UHMWPE/CNC fibers and the kebab crystals are grown around the CNCs. There was almost no difference between pure UHMWPE fibers and UHMWPE/CNC fibers in orientation. But the degree of crystallinity of various stages of UHMWPE/CNC fibers was respectively higher than the corresponding stage of pure UHMWPE fibers. Moreover, the addition of 1 wt% CNCs improved the thickness of kebab crystals and accelerated the transformation of kebab to shish.     

Extensional rheology of cellulose/NaOH/urea/H<Subscript>2</Subscript>O solutions

The extensional flow behaviors of cellulose/NaOH/urea/H₂O solution were investigated by using capillary breakup extensional rheometry (CaBER). The effects of temperature, storage time and cellulose concentrations on both the storage modulus G′ and the loss modulus G″ were also analyzed. For 2 wt% cellulose solution, the G′, G″ and filament lifetime remained unchanged after long storage time. While, for 4 wt% cellulose solution, physical gels could form at either higher temperature or for longer storage time, and the filament lifetime, the relaxation time (λ _e ) and the initial extensional viscosity (η _e0) first increased and then decreased with increase of the storage time. The transition points of the filament lifetime shifted to lower storage time with the increase of the temperature. The η _e0 is proportional to λ _e . The results presented suggest that the extensional properties of the cellulose/NaOH/urea/H₂O solution first increase and then decrease during the gelation process, and the spinning time, which decreases linearly with the increase in the storage temperature, must be controlled below the time that η _e0 starts to decrease.     

Towards efficient electromagnetic interference shielding performance for polyethylene composites by structuring segregated carbon black/graphite networks

An electromagnetic interference (EMI) shielding composite based on ultrahigh molecular weight polyethylene (UHMWPE) loaded with economical graphite-carbon black (CB) hybrid fillers was prepared via a green and facile methodology, i.e., high-speed mechanical mixing combined with hot compression thus avoiding the assistance of the intensive ultrasound dispersion in volatile organic solvents. In this composite, the graphite-CB hybrid fillers were selectively distributed in the interfacial regions of UHMWPE domains resulting a typical segregated structure. Thanks to the specific morphology of segregated conductive networks along with the synergetic effect of large-sized graphite flakes and small-sized CB nanoparticles, a low filler loading of 7.7 vol% (15 wt%) yielded the graphite-CB/UHMWPE composites with a satisfactory electrical conductivity of 33.9 S/m and a superior shielding effectiveness of 40.2 dB, manifesting the comparable value of the pricey large-aspect-ratio carbon nanofillers (e.g., carbon nanotubes and graphene nanosheets) based polymer composites. More interestingly, with the addition of 15 wt% graphite-CB (1/3, W/W) hybrid fillers, the tensile strength and elongation at break of the composite reached 25.3 MPa and 126%, respectively; with a remarkable increase of 58.1% and 2420% over the conventional segregated graphite/UHMWPE composites. The mechanical reinforcement could be attributed to the favor of the small-sized CB particles in the polymer molecular diffusion between UHMWPE domains which in turn provided a stronger interfacial adhesion. This work provides a facile, green and affordable strategy to obtain the polymer composites with high electrical conductivity, efficient EMI shielding, and balanced mechanical performance.     

Improvement of bagasse fiber–cement composites by addition of bacterial nanocellulose: an inverse gas chromatography study

The design of green fiber-reinforced nanocomposites with enhanced properties and durability has attracted attention from scientists. The present study aims to investigate the potential of bacterial nanocellulose (BNC) as a green additive for fiber–cement composites. Inverse gas chromatography (IGC) was used to evaluate the influence of incorporation of BNC as powder or gel, or coated onto the bagasse fibers, on the fiber–cement composite (FCC) surface. The results indicated that BNC incorporation made the FCC surface more reactive, increasing the dispersive component of the surface energy. The most relevant effects were found for BNC incorporation as gel or coated on the fibers. Incorporation of BNC as gel resulted in a predominantly organic FCC surface with substantial decreased surface basicity (K _a/K _b ratio from 2.88 to 5.75). IGC also showed that FCC with BNC incorporated as gel was more susceptible to hydration. However, BNC coated on fibers prevented fiber mineralization, increasing the inorganic materials at the surface, which caused an increase in the surface basicity (K _a/K _b ratio decrease to 2.00). These promising results could contribute to development of a new generation of green hybrid composites. The IGC technique enabled understanding of the physicochemical changes that occur on deliberate introduction of nanosized bacterial cellulose into fiber–cement composites.     

Effect of alkali metal salts on decomposition of ionic liquid like organic salt

N ¹,N ¹,N ²,N ²-tetramethylethane-1,2-diamine-based ionic salts (TMEDA), N ¹,N ¹,N ¹,N ²,N ²,N ²-hexamethylethane-1,2-diaminium dicyanamide (HMEDA-(DCA)₂) were prepared following the quaternization and subsequent ion exchange. The chemical structure of the HMEDA-(DCA)₂ was confirmed using ¹³C NMR spectrum and elemental analysis. The corresponding viscosity of its 60 wt% solution was found to be lower than 5 cP at room temperature, which was critical for propellant application. The ignition delay of 40 wt% HMEDA-(DCA)₂ solution was decreased to 20–30 ms dramatically using alkali metal salts, Li(CH₃COO), Mg(CH₃COO)₂, and Ca(CH₃COO)₂ as a co-catalyst when white fume nitric acid was utilized as an oxidizer.     

Investigation of Solution p<Emphasis Type="Italic">K</Emphasis><Subscript>a</Subscript> and Thermodynamic Values of Lamivudine and Pefloxacin Drugs by Ab initio and DFT Methods

In this work we investigate the thermodynamic properties and pK_a value of lamivudine and pefloxacin drugs, in aqueous solutions, by ab initio and density functional theory (DFT) methods at different temperatures. Molecular structures and solute–solvent effects of the anions, cations, and neutral molecules of lamivudine and pefloxacin were studied by the polarizable continuum model (PCM). The calculation was done at the DFT-B3LYP/6-31+G(d) level of theory using Tomasi’s method to analyze the formation of intermolecular hydrogen bonds (IHB) in aqueous solution. The pK_a1 values of lamivudine and pK_a2 values of pefloxacin increase with temperature increase. In contrast, the pK_a1 values of pefloxacin decrease when the temperature increases. Further, the thermodynamic properties of the ionization processes (?H, ?S and ?G) of the drugs in aqueous solution were determined and discussed. The results of this work are in good agreement with the literature data at 298.15 K.     

Thermal behavior of flax and jute reinforced in matrix acrylic composite

Natural fabric such as flax and jute was considered in biaxial plain reinforcement in matrix of acrylic resin, and the composite is prepared in hand layup techniques. Fabric mass fraction of 7% was used in the matrix of composite. The samples were treated at r.t and 60 °C for the final fabrication. Scanning electron microscopy was carried out to support the microstructure effect of composite in terms of thermal change. Thermogravimetric and differential thermogravimetric analysis and residual compositional analysis with FTIR were carried out for the composite and matrix samples. The mechanical and viscoelastic properties, as well as the influence of frequency and fibers types, were evaluated, in flexural mode, by means of dynamical mechanical analysis. Glass transition (T _g) and initial decomposition (T _i) temperatures increase with incorporation of fibers into the matrix. While T _i of flax and jute composite was similar, T _g in case of flax improves than jute fabric-reinforced composite. This type of composites can be used in the automotive sector, in exterior and exterior components.     

Molecular dynamics simulations of the characteristics of sodium carboxymethyl cellulose with different degrees of substitution in a salt solution

Sodium carboxymethyl cellulose (SCMC) with different degrees of substitution (DS) possesses structural characteristics and physicochemical properties that are important in broad areas of industrial applications. This reported work investigated the structural characteristics, including the effective length (L _ef), the radius of gyration (R _g), and the hydrodynamic radius (R _H), and the physicochemical properties, including intrinsic viscosity ([η]) and salt tolerance, of SCMC with a DS more than 1.0 in NaCl solution using molecular dynamics (MD) simulations. In the MD simulations, the DS of SCMC varied from 1.2 to 2.8, and the NaCl concentration varied from 0 to 1.4 mol/L. MD simulation results showed that with the increment of NaCl concentration, the L _ef (or R _g or R _H) of SCMC decreased; with the increment of the DS, the L _ef of SCMC increased. Also, the variation tendency of [η] in the NaCl solution was consistent with its L _ef (or R _g or R _H). It was noted that the salt tolerance (represented by D) of SCMC increased as the DS increased. In addition, the sharp variation of the D value of SCMC occurred in the range of DS of 1.6 to 2.0, which agreed with the reported experimental results. Radial distribution function analyses showed that the Na⁺ cations had a stronger interaction with the carboxyl groups in SCMC with lower DS when it was present in a salt solution of higher concentration, which also reasonably explained the variation of L _ef, R _g, R _H, [η], and D of SCMC in NaCl solution.     

The thermochemical characteristics of solution of DL-α-alanylglycine and DL-α-alanylalanine in water-alcohol mixtures at 298.15 K

The integral enthalpies of solution of DL-α-alanylglycine and DL-α-alanylalanine in water-ethanol, water-n-propanol, and water-isopropanol mixtures were measured calorimetrically at alcohol concentrations x ₂ = 0?0.4 mole fractions. The standard enthalpies of solution (Δ_sol H°) of the peptides and their transfer (Δ_tr H°) from water into the mixed solvents were calculated. The influence of the structure and properties of the solutes and mixture composition on the enthalpy characteristics were considered. The Δ_sol H° = f(x ₂) and Δ_tr H° = f(x ₂) dependences were found to have extrema. The enthalpy coefficients of pair interactions (h _xy ) between the peptide and alcohol molecules were calculated. The coefficients were positive and increased in the series ethanol, n-propanol, isopropanol.     

Ro-vibrating energy states of a diatomic molecule in an empirical potential

An approximate analytical solution of the Schrödinger equation is obtained to represent the rotational–vibrational (ro-vibrating) motion of a diatomic molecule. The ro-vibrating energy states arise from a systematical solution of the Schrödinger equation for an empirical potential (EP) V _±(r) = D _e {1 ? (?/δ)[coth (ηr)]^±1/1 ? (?/δ)}² are determined by means of a mathematical method so-called the Nikiforov–Uvarov (NU). The effect of the potential parameters on the ro-vibrating energy states is discussed in several values of the vibrational and rotational quantum numbers. Moreover, the validity of the method is tested with previous models called the semiclassical (SC) procedure and the quantum mechanical (QM) method. The obtained results are applied to the molecules H₂ and Ar₂.     

The thermochemical characteristics of solution of DL-α-alanylglycine and DL-α-alanyl-DL-α-alanine in water-organic solvent mixtures at 298.15 K

The integral enthalpies of solution of DL-α-alanylglycine and DL-α-alanyl-DL-α-alanine in water-organic solvent (acetonitrile, 1,4-dioxane, acetone, N,N-dimethylformamide, and N,N-dimethylsulfoxide) mixtures were measured at organic component concentrations x ₂ = 0–0.4 mole fractions and T = 298.15 K. The standard enthalpies of solution (Δ_sol H°) and transfer (Δ_tr H°) of the peptides from water into mixed solvents were calculated. The influence of the structure and properties of solutes and mixture composition on the thermochemical characteristics of the peptides was considered. The enthalpy coefficients of pair interactions (h _xy ) of DL-α-alanylglycine and DL-α-alanyl-DL-α-alanine with organic solvent molecules were calculated. The h _xy values were correlated with the properties of organic solvents using the Kamlet-Taft equation.     

Molecular Dynamics Study on Carbon Dioxide Absorbed Potassium Glycinate Aqueous Solution

Molecular dynamics (MD) simulations have been performed to investigate the effects on structure, transport properties, and dynamical properties in the potassium glycinate aqueous solution caused by carbon dioxide (CO₂) absorption. The optimized structure and charges of constituents of the solution, such as the glycine zwitterion, have been determined by Gaussian09 using the density functional theory. The obtained pair distribution functions, g _ij (r)’s, show the significant distribution difference of bicarbonate ion, \({\text{HCO}}_{3}^{ - }\), around the glycine anion and glycine zwitterion. The shear viscosity and diffusion coefficient obtained by MD show different CO₂ concentration dependences. The frequency dependent diffusion coefficient D _i (ν) for N and C in glycine ions are mainly influenced by the cage effect of surrounding water molecules, whereas D _i (ν) for H show the characteristic vibration due to the structure difference of the glycine ions.     

Effect of donor and acceptor properties of solvents on the kinetics of photoreduction of sterically hindered <Emphasis Type="Italic">о</Emphasis>-benzoquinones

Effect of the solvent nature on the kinetics of photoreduction of 3,6-di-tert-butyl-1,2-benzoquinone and its six derivatives in the presence of N,N-dimethylaniline and 4-(N,N-dimethylamino)benzaldehyde has been investigated. It has been found that for the о-quinone—amine pair, for which the free energy change of electron transfer is ΔG_e > +0.11 eV, the rate constant of о-quinone photoreduction k_H decreases proportionally to the increase in the acceptor number of the solvent. For the о-quinone—amine pair with ΔG_e < +0.11 eV, the k_H value decreases proportionally to the increase in the donor number of the solvent. It has been established that the enhancement of the electron-acceptor properties of the solvent leads to the emergence of kinetic isotope effect for the reactant pairs of 3,6-di-tert-butyl-1,2-benzoquinone and 4,5-dimethoxy-3,6-di-tert-butyl-1,2-benzoquinone with N,N-di-methylaniline (ΔG_e = +0.11 and +0.22 eV, respectively).     

The enthalpies of solution of L-α-alanyl-L-α-alanine in water-organic solvent mixtures at 298.15 K

The integral enthalpies of solution (T = 298.15 K) of L-α-alanyl-L-α-alanine in aqueous-organic solvents (acetonitrile, 1,4-dioxane, acetone, formamide, N-methylformamide, N,N-dimethylformamide, N,N-diethylformamide, and N,N-dimethylsulfoxide) were measured at organic component concentrations x ₂ = 0–0.3 mole fractions. The standard enthalpies of solution (Δ_sol H ^o) and transfer (Δ_tr H ^o) of the peptide from water into mixed solvents were calculated. The influence of the structure and properties of solutes and mixture composition on solute thermochemical characteristics is considered. The enthalpy pair interaction coefficients h _xy between L-α-alanyl-L-α-alanine and organic solvent molecules were calculated. The linear Kamlet-Taft four-parameter equation was used to reveal correlation between the h _xy values and the properties of organic solvents.     

Highly efficient mesoporous WO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/KIT-6 catalysts for oxidative desulfurization of dibenzothiophene with hydrogen peroxide

Oxidative desulfurization (ODS) of organic compounds containing sulfur element from a model oil was performed using tungsten oxide catalysts supported on mesoporous silica with cubic Ia3d mesostructure, well-defined mesopores (7.2 nm), high surface area (719 m²/g), and three-dimensional pore network (WO _x /KIT-6). The prepared WO _x /KIT-6 catalysts (5–20 wt% WO _x ) were characterized by X-ray diffraction analysis, N₂ sorption measurements, electron microscopy, H₂-temperature programmed reduction, Raman spectroscopy, and thermogravimetric analysis. Among the mesoporous catalysts, 10 wt% WO _x /KIT-6 exhibited the best catalytic performance. Sulfur-containing organic compounds, such as dibenzothiophene, 4,6-dimethyldibenzothiophene, and benzothiophene, were completely (100 %) removed from the model oil over 10 wt% WO _x /KIT-6 catalyst in 2 h. In addition, the catalyst could be reused several times with only slight decrease in catalytic activity.     

Crosslinking kinetics of polyethylene with small amount of peroxide and its influence on the subsequent crystallization behaviors

Crosslinking reactions of high density polyethylene with low peroxide concentrations ranging from 0.1 wt% to 1.0 wt% at temperatures of 170, 180 and 190 ° C were monitored by rheological measurements. A critical gel forms at the peroxide concentration of 0.2 wt%, where the transition from long chain branching generation to crosslinking network formation could occur. Rheokinetics of crosslinking can be fitted well by Ding-Leonov's model. The curing rate k_2 at the earlier stage exhibits about 3 times acceleration per 10 °C with increasing temperature, while the equilibrium modulus G′ at the fully cured stage is almost independent of temperature. Influences of crosslinking on the subsequent crystallization behaviors were detected by DSC measurements. Above the critical gel concentration, crystallization is largely retarded as evidenced by the lower crystallization temperature Tc and crystallinity X_c due to the network formation. The secondary crystallization valley located at the temperature near 80 °C can be observed above the critical concentration, which becomes more evident with the increasing peroxide concentration and curing temperature. This phenomenon provides another evidence of crystallization retardation by the crosslinking network.     

Synthesis of water soluble metalloporphyrin-cored amphiphilic star block copolymer photocatalysts for an environmental application

Two series of water-soluble metalloporphyrin-cored amphiphilic star block copolymers were synthesized by controlled radical polymerizations such as atom transfer radical polymerization (ATRP) and reversible addition fragmentation chain transfer (RAFT), which gave eight amphiphilic block copolymer arm chains consisting of poly(n-butyl acrylate-b-poly(ethylene glycol) methyl ether methacylate) (PnBA-b-PEGMEMA, M_n,GPC = 78,000, M_w/M_n = 1.2, 70 wt% of PPEGMEMA) and poly(styrene-b-2-dimethylamino ethyl acrylate) (PS-b-PDMAEA, M_n,GPC = 83,000, M_w/M_n = 1.2, 67 wt% of PDMAEA), yielding porphyrin(Pd)-(PnBA-b-PPEGMEMA)₈ and porphyrin(Pd)-(PS-b-PDMAEA)₈, respectively. Obtained metalloporphyrin polymer photocatalysts were homogeneously solubilized in water to apply to the removal of chlorophenols in water, and was distinguished from conventional water-insoluble small molecular metalloporphyrin photocatalysts. Notably, we found that the water-soluble star block copolymers with hydrophobic–hydrophilic core–shell structures more effectively decomposed the chlorophenol, 2,4,6-trichlorophenol (2,4,6-TCP), in water under visible light irradiation (k = 1.39 h^?1, t_1/2 = 0.5 h) in comparison to the corresponding water-soluble star homopolymer, because the hydrophobic core near the metalloporphyrin effectively captured and decomposed the hydrophobic chlorophenols in water.     

Combined De-Algination Process as a Fractionation Strategy for Valorization of Brown Macroalga <Emphasis Type="Italic">Saccharina japonica</Emphasis>

A combined process, de-algination followed by enzymatic saccharification, was designed to produce alginate and glucose from Saccharina japonica consecutively. The process conditions of de-algination were optimized separately for each stage of acidification and alkaline extraction. Collectively, the de-algination yield was 70.1% under the following optimized conditions: 2.4 wt% of Na₂CO₃, 70 °C, and 100 min with the acidified S. japonica immersed in a 0.5 wt% H₂SO₄ solution for 2 h at room temperature. The glucan content in the de-alginated S. japonica increased to 38.0%, which was approximately fivefold higher than that of the raw S. japonica. The enzymatic hydrolysis of the de-alginated S. japonica almost completed in 9 h, affording 5.2 g (96.8% of glucan digestibility) of glucose at a de-alginated S. japonica loading of 14.2 g.     

Compositional effect of ZrO2 nanofillers on a PVDF-co-HFP based polymer electrolyte system for solid state zinc batteries

Composite polymer electrolytes(CPEs) comprising poly(vinilydene fluoride-hexafluoro propylene), PVDF-coHFP and zinc triflate, Zn(CF3SO3)2 with varying concentrations of ZrO_2 nanofillers were prepared by solution casting technique with N,N-dimethyl formamide(DMF) as the common solvent. The polymer electrolyte specimen with the particular composition 75 wt% PVDF-co-HFP: 25 wt% Zn Tf + 7 wt% Zr O2 showed the highest conductivity of 4.6 × 10-4 S/cm at 298 K as confirmed from impedance measurements and favored by the rich amorphous phase of the CPE revealed from room temperature X-ray diffraction analysis(XRD). The electrical conductivity relaxation time and its distribution within the materials have been evaluated from the electric modulus M 2 and impedance Z" data which showed the occurrence of non-Debye type of relaxation phenomenon. The changes in the surface morphology of the CPEs were examined using scanning electron microscopy(SEM). The electrochemical stability window of CPE is found to be 2.6 V with a thermal stability up to 300 °C. An electrochemical cell has been fabricated based on Zn/MnO_2 electrode couple under a constant load of 1 MΩ and its discharge characteristics have been evaluated.     

Thermal and redox dual responsive poly(<Emphasis Type="SmallCaps">L</Emphasis>-glutamate) with oligo(ethylene glycol) side-chains

A series of poly(L-glutamate)s grafted with oligo(ethylene glycol) (OEG) side-chains through the thioether linkages (PALG _n -g-EG _x , x = 2, 3 and 4) were prepared by ring-opening polymerization (ROP) of γ-allyl-L-glutamate N-carboxyanhydride (ALG-NCA) and thiol-ene photoaddition. The chemical structures and physical properties were characterized by ¹H-NMR, Fourier transform infrared (FTIR), circular dichroism (CD), etc. The PALG _n -g-EG _x samples with x = 3 and 4 displayed lower critical solution temperature (LCST) in water due to the presence of OEG units. The clouding point (CP) of polypeptides can be finely tuned by changing the side chain structures, molecular weights and sample concentrations. In addition, the thioether linkages in the side chains offer additional redox-responsive properties. The influence of both OEG units and thioether linkages on the LCST behavior was systematically investigated. This work provides an efficient way to prepare multi-stimuli responsive materials with highly tunable properties.