Immobilization of cholesterol esterase and cholesterol oxidase onto sol-gel films for application to cholesterol biosensor

Cholesterol oxidase (ChOx) and cholesterol esterase (ChEt) have been covalently immobilized onto tetraethylorthosilicate (TEOS) sol-gel films. The tetraethylorthosilicate sol-gel/ChEt/ChOx enzyme films thus prepared have been characterized using scanning electron microscopic (SEM), UV-vis spectroscopic, Fourier-transform-infrared (FTIR) spectroscopic and amperometric techniques, respectively. The results of photometric measurements carried out on tetraethylorthosilicate sol-gel/ChEt/ChOx reveal thermal stability up to 55 °C, response time as 180 s, linearity up to 780 mg dL⁻¹ (12 mM), shelf life of 1 month, detection limit of 12 mg dL⁻¹ and sensitivity as 5.4 × 10⁻⁵ Abs. mg⁻¹ dL⁻¹.     

Amperometric cholesterol biosensor based on immobilized cholesterol esterase and cholesterol oxidase on conducting polypyrrole films

Fabrication of an amperometric cholesterol biosensor by co-immobilization of cholesterol esterase (ChEt) and cholesterol oxidase (ChOx) onto conducting polypyrrole (PPY) films using electrochemical entrapment technique is described. Electrochemical polymerization was carried out using a two-electrode cell configuration at 0.8 V. Characterization of resulting amperometric biosensor for the estimation of cholesterol has been experimentally determined in terms of linear response range, optimum pH, applied potential, temperature, and shelf-life. These PPY/ChEt/ChOx electrodes can be used for cholesterol ester estimation from 1 to 8 mM and have shelf-life of about 4 weeks at 4 °C during which about 15 estimations of cholesterol ester could be made. The sensitivity of PPY/ChEt/ChOx electrode has been found to be 0.15 μA/mM and the apparent K_m value for this electrode is 9.8 mM. Conductivity of the polymer films found to be about 3×10⁻³ S/cm.     

Development of cholesterol biosensor based on immobilized cholesterol esterase and cholesterol oxidase on oxygen electrode for the determination of total cholesterol in food samples

The development of a cholesterol biosensor by co-immobilization of cholesterol esterase (ChEt) and cholesterol oxidase (ChOX) on oxygen electrode is described. The electrode consists of gold cathode and Ag/AgCl anode. The enzymes were immobilized by cross-linking with glutaraldehyde and Bovine Serum Albumin (BSA). The immobilized enzymatic membrane was attached to the tip of the electrode by a push cap system. The optimum pH and temperature of the sensor was determined, these are 6 and 25 degrees C respectively. The developed sensor was calibrated from 1-75 mg/dl of cholesterol palmiate and found linear in the range of 2-50 mg/dL. The calibration curve was drawn with V(i) (ppm/min)(initial velocity) vs different concentrations of cholesterol palmiate (mg/dL). The application of the sensor to determine the total cholesterol in different real food samples such as egg, meat was investigated. The immobilized enzymatic layer can be reused over 30 times and the stability of the enzymatic layer was studied up to 9 weeks.     

Radiation grafting of acrylic acid onto polytetrafluoroethylene films for glucose oxidase immobilization and its application in membrane biosensor

Radiation induced grafting of acrylic acid (AA) onto 40 μm polytetrafluoroethylene (PTFE) films was carried out by the direct method of multiple (discrete) and single irradiation form ⁶⁰Co source at different doses up to 100 kGy and room temperature. Depending on the method, the grafting takes place either on the surface layer or within the polymer matrix. The graft copolymers synthesized (PTFE-g-PAA) were transformed into ionomers by treatment with KOH. Both forms were used as carriers for immobilization of enzymes. The copolymers in H- and K-forms were activated by the acylazide method and glucose oxidase (GOD) was immobilized on them. The most suitable proved to be the ionomers PTEE-g-COOK obtained by single irradiation, possessing activity of ca. 120 mU/cm². Enzyme biosensor was designed based on Clark-type electrode and the active membranes prepared, where the membrane plays both the roles of enzyme and oxygen membrane. It can be used for determination of glucose in solutions.     

Comparison of biosensors based on entrapment of cholesterol oxidase and cholesterol esterase in electropolymerized films of polypyrrole and diaminonaphthalene derivatives for amperometric determination of cholesterol

Cholesterol amperometric biosensors constructed with enzymes entrapped in electropolymerized layers of polypyrrole and poly-naphthalene derivative polymers are compared. The biosensors are based on entrapment of cholesterol oxidase and/or cholesterol esterase in monolayer or multilayer films electrochemically synthesised from pyrrole, 1,8-diaminonaphthalene (1,8-DAN), and 1,5-diaminonaphthalene (1,5-DAN) monomers. Seven configurations were assayed and compared, and different analytical properties were obtained depending on the kind of polymer and the arrangement of the layers. The selectivity properties were evaluated for the different monolayer and bilayer configurations proposed as a function of the film permeation factor. All the steps involved in the preparation of the biosensors and determination of cholesterol were carried out in a flow system. Sensitivity and selectivity depend greatly on hydrophobicity, permeability, compactness, thickness, and the kind of the polymer used. In some cases a protective outer layer of non-conducting poly(o-phenylenediamine) polymer improves the analytical characteristics of the biosensor. A comparative study was made of the analytical performance of each of the configurations developed. The biosensors were also applied to the flow-injection determination of cholesterol in a synthetic serum.     

Ordered mesoporous polyaniline film as a new matrix for enzyme immobilization and biosensor construction

Ordered mesoporous polyaniline film has been fabricated by electrodepositing from the hexagonal lyotropic liquid crystalline (LCC). Horseradish peroxidase (HRP), as a symbol biomolecule, was successfully immobilized on the film to construct a new kind of hydrogen peroxide biosensor. The biosensor combined the advantages of the good conductivity of polyaniline and the higher surface area of the ordered mesoporous film. Polyaniline could be served as a wire to relay electron between HRP and the electrode. The high surface area of the film supplied more sites for HRP immobilization, therefore increased the catalytic activity of the biosensor. The ordered mesoporous character of the film increased the rate of mass transport, which resulted in the improvement of sensor response and linearity. The biosensor displayed excellent electrocatalytic response to the detection of H₂O₂ in a concentration range from 1.0 μM to 2.0 mM with a detection limit of 0.63 μM. Good reproducibility, stability, high precision, wide linearity and low detection limit were assessed for the biosensor.     

Amperometric determination of total cholesterol in serum with use of immobilized cholesterol esterase and cholesterol oxidase

Cholesterol esterase and cholesterol oxidase were immobilized on octyl-agarose gel, activated with cyanogen bromide and placed in a reactor. The sensor system for total cholesterol was assembled with the immobilized enzyme reactor, a hydrogen peroxide electrode and a peristaltic pump. Characteristics of the sensor system were investigated by using cholesterol palmitate as a standard substrate. A linear relationship was obtained between peak current and cholesterol palmitate concentration below 1000 mg dl^-1 (10.3 mM). A 10-μl sample could be assayed in 5 min. Total cholesterol in human serum was determined in the range 100–400 mg dl^-1. The standard deviation for the determination of 50 samples of 300 mg dl^-1 was 6 mg dl^-1 (2%). The system was used for 300 assays without loss of enzymatic activity. The correlation coefficient was 0.94 for 27 samples of human sera analyzed by the system proposed and by the conventional chemical method.     

Immobilization of lactate dehydrogenase on tetraethylorthosilicate-derived sol-gel films for application to lactate biosensor

Tetraethylorthosilicate (TEOS)-derived sol-gel films were utilized for the immobilization of lactate dehydrogenase (LDH) by physical adsorption and sol-gel/LDH/sol-gel sandwich configuration. An attempt was made to ascertain the optimum pH and temperature for the immobilized LDH. It was shown that TEOS-derived sol-gel films containing physically adsorbed LDH exhibited linearity from 0.5 to 4 mM, whereas those containing LDH in sandwich configuration showed linearity from 0.5 to 3 mM l-lactate. These sol-gel films, immobilized with LDH, were found to be stable for about 4 weeks at 4–10°C.     

Covalent immobilization of Candida antarctica lipase B on nanopolystyrene and its application to microwave-assisted esterification

Nanopolystyrene was used as a solid support for the covalent immobilization of Candida antarctica lipase B (CalB) using the photoreactive reagent 1-fluoro-2-nitro-4-azido benzene (FNAB) as a coupling reagent. The obtained derivative was then used as a biocatalyst in a microwave assisted esterification experiment. Factors such as contact time, pH, and enzyme concentration were investigated during immobilization. The hydrolytic activity, thermal, and operational stability of immobilized-CalB were determined. The maximum immobilized yield (218 μg/mg support) obtained at pH 6.8 exhibited optimum hydrolytic activity (4.42 × 10³ mU p-nitrophenol/min). The thermal stability of CalB improved significantly when it was immobilized at pH 10, however, the immobilized yield was very low (93.6 μg/mg support). The immobilized-CalB prepared at pH 6.8 and pH 10 retained 50% of its initial activity after incubation periods of 14 and 16 h, respectively, at 60 ℃. The operational stability was investigated for the microwave assisted esterification of oleic acid with methanol. Immobilized-CalB retained 50% of its initial activity after 15 batch cycles in the microwave-assisted esterification. The esterification time was notably reduced under microwave irradiation. The combined use of a biocatalyst and microwave heating is thus an alternative total green synthesis process.     

Electrogeneration of polypyrrole/alginate films for immobilization of glucose oxidase

Electrogenerated PPy doped with pSA was used as a substrate for immobilization of GOD. This was achieved via covalent bonding of carboxyl groups of the main chain of alginate with amino groups of the enzyme. The pH-induced aggregation behavior of SA in aqueous solution was employed to provide optimum conditions for electrochemical preparation of PPy by galvanostatic methods. GOD was attached to the electrode surface by reaction between the carboxyl groups in the main chain of pSA with amino groups of GOD after treatment with EDC and NHS. The linkage of GOD enzyme to the conductive surface was characterized by ATR spectroscopy and SEM CV was used to demonstrate the bioactivity of the enzyme electrode toward glucose.     

Covalent attachment of glucose oxidase to an Au electrode modified with gold nanoparticles for use as glucose biosensor

A feasible method to fabricate glucose biosensor was developed by covalent attachment of glucose oxidase (GOx) to a gold nanoparticle monolayer modified Au electrode. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) of ferrocyanide followed and confirmed the assemble process of biosensor, and indicated that the gold nanoparticles in the biosensing interface efficiently improved the electron transfer between analyte and electrode surface. CV performed in the presence of excess glucose and artificial redox mediator, ferrocenemethanol, allowed to quantify the surface concentration of electrically wired enzyme (Gamma(E)(0)) on the basis of kinetic models reported in literature. The Gamma(E)(0) on proposed electrode was high to 4.1 x 10(-12) mol.cm(-2), which was more than four times of that on electrode direct immobilization of enzyme by cystamine without intermediate layer of gold nanoparticles and 2.4 times of a saturated monolayer of GOx on electrode surface. The analytical performance of this biosensor was investigated by amperometry. The sensor provided a linear response to glucose over the concentration range of 2.0 x 10(-5)-5.7 x 10(-3) M with a sensitivity of 8.8 microA.mM(-1).cm(-2) and a detection limit of 8.2 microM. The apparent Michaelis-Menten constant (K(m)(app)) for the sensor was found to be 4.3 mM. In addition, the sensor has good reproducibility, and can remain stable over 30 days.     

Application of polyaniline/sol-gel derived tetraethylorthosilicate films to an amperometric lactate biosensor.

The electrochemical entrapment of polyaniline (PANI) onto sol-gel derived tetraethylorthosilicate (TEOS) films deposited onto indium-tin-oxide (ITO) coated glass has been utilized for immobilization of lactate dehydrogenase (LDH). The performance of these sol-gel/PANI/LDH electrodes has been investigated as a function of the lactate concentration, applied potential, pH of the medium and interferents. The amperometric response of the electrodes under optimum conditions exhibited a linear relationship from 1 mM to 4 mM. An attempt has been made to extend the linearity up to 10 mM for lactate by coating an external layer of polyvinyl chloride (PVC) over the sol-gel/PANI/LDH electrodes with a correlation coefficient of 0.89. These sol-gel/PANI/LDH electrodes have a response time of about 60 s, a shelf life of about 8 weeks at 0-4 degrees C and have implications in a lactate biosensor.     

Construction of biosensor for hypoxanthine determination by immobilization of xanthine oxidase and uricase in polypyrrole-paratoluenesulfonate film

Journal of Solid State Electrochemistry - A highly selective and stable amperometric biosensor for the determination of the hypoxanthine (Hx) molecule was designed in this study. For this purpose,...     

Reagentless amperometric glucose biosensor based on the immobilization of glucose oxidase on a ferrocene@NaY zeolite composite

Ferrocene (Fc) was encapsulated in the cavities of a NaY zeolite by vapor diffusion via sublimation at below 100?°C. The resulting Fc@NaY zeolite composite was investigated by power X-ray diffraction, diffuse reflectance UV?Cvis and FT-IR spectroscopy, and by cyclic voltammetry. The results indicated that Fc was encapsulated into the zeolite whose microporous structure had remained intact. The Fc in the silica matrix had retained its electroactivity and did not leach out. A glucose biosensor was obtained by immobilization of the modified zeolite and glucose oxidase on a carbon paste electrode. It displays a linear response to glucose (from 0.8???M to 4.0?mM), a detection limit of 0.2???M, and a response time of 4?s. The good performance of the biosensor is ascribed to the biocompatibility of the zeolite and presence of Fc which facilitates the electron transfer from the enzyme to the surface of the electrode.

Sol–gel derived nanoporous cerium oxide film for application to cholesterol biosensor

Cholesterol oxidase (ChOx) has been immobilized onto sol–gel derived nano-structured cerium oxide (NS-CeO₂) film deposited on indium-tin-oxide (ITO) coated glass substrate. Phase identification of sol–gel NS-CeO₂ film carried out using X-ray diffraction (XRD) yields reflection peak at 29.4° corresponding to (1 1 1) plane with oriented crystallite (34 nm) along c-axis normal to the substrate. Electrochemical studies reveal that NS-CeO₂ provides electroactive surface for the loading of ChOx and enhances electron transfer rate in the ChOx/NS-CeO₂/ITO bioelectrode. The low value of Michaelis–Menten constant (K_m) obtained as 2.08 mM indicates enhanced ChOx affinity to cholesterol. The observed results show application of sol–gel derived NS-CeO₂ for biosensing without any functionalization.     

Incorporation of glucose oxidase into Langmuir-Blodgett films based on Prussian blue applied to amperometric glucose biosensor

Glucose oxidase (GOx) was immobilized in the organic-inorganic Langmuir-Bldogett (LB) films consisting of octadecyltrimethylammonium (ODTA) and nanosized Prussian blue (PB) clusters. The amperometric glucose biosensors based on the LB films were fabricated and tested. It was found that the sensors exhibited a clear response current under an applied voltage of 0.0 V (vs Ag/AgCl). The linearity of current density versus glucose concentration was confirmed below 15 mmol/L concentration. This is the first observation of biosensor function of the hybrid organic-inorganic LB films. The successful preparation of glucose sensors operating at the very low potential indicates that the adsorbed PB clusters in the LB films act as an electrocatalyst for the electrochemical reduction of hydrogen peroxide, which is the final product of the enzymatic reaction sequence. The observed low potential applicability is estimated to inhibit the responses of interferants such as ascorbic acid, uric acid, and acetominophen. It was also found that an electrostatic interaction between positively charged ODTA+ and the adsorbed species of both GOx and PB provided a stabilized adsorption state in the LB films. Such stable immobilization contributes to the steady amperometric response current observed in the present ODTA/PB/GOx LB films.     

Covalent immobilization of carbohydrates on sol-gel-coated microplates

Carbohydrate microarrays have attracted increasing attention in recent years because of their ability to monitor biologically important protein-carbohydrate interactions in a high-throughput manner. Here we have developed an effective approach to immobilizing intact carbohydrates directly on polystyrene microtiter plates coated with amine-functionalized sol-gel monolayers. Lectin binding was monitored by fluorescence spectroscopy using these covalent arrays of carbohydrates that contained six mono- and di-saccharides on the microplates. In addition, binding affinities of lectin to carbohydrates were also quantitatively analyzed by determining IC(50) values of lectin-specific antibody with these arrays. Our results indicate that microplate-based carbohydrate arrays can be efficiently fabricated by covalent immobilization of intact carbohydrates on sol-gel-coated microplates. The microplate-based carbohydrate arrays can be applied for screening of protein-carbohydrate interactions in a high-throughput manner.     

Covalent immobilization of glucose oxidase onto new modified acrylonitrile copolymer/silica gel hybrid supports

New polymer/silica gel hybrid supports were prepared by coating high surface area of silica gel with modified acrylonitrile copolymer. The concentrations of the modifying agent (NaOH) and the modified polymer were varied. GOD was covalently immobilized on these hybrid supports and the relative activity and the amount of bound protein were determined. The highest relative activity and sufficient amount of bound protein of the immobilized GOD were achieved in 10% NaOH and 2% solution of modified acrylonitrile copolymer. The influence of glutaraldehyde concentration and the storage time on enzyme efficiency were examined. Glutaraldehyde concentration of 0.5% is optimal for the immobilized GOD. It was shown that the covalently bound enzyme (using 0.5% glutaraldehyde) had higher relative activity than the activity of the adsorbed enzyme. Covalently immobilized GOD with 0.5% glutaraldehyde was more stable for four months in comparison with the one immobilized on pure silica gel, hybrid support with 10% glutaraldehyde and the free enzyme. The effect of the pore size on the enzyme efficiency was studied on four types of silica gel with different pore size. Silica with large pores (CPC-Silica carrier, 375 A) presented higher relative activity than those with smaller pore size (Silica gel with 4, 40 and 100 A). The amount of bound protein was also reduced with decreasing the pore size. The effect of particle size was studied and it was found out that the smaller the particle size was, the greater the activity and the amount of immobilized enzyme were. The obtained results proved that these new polymer/silica gel hybrid supports were suitable for GOD immobilization.     

Covalent and selective immobilization of fusion proteins

A general method for the covalent immobilization of fusion proteins is presented. The approach is based on the unusual mechanism of the human O6-alkylguanine-DNA alkyltransferase, which irreversibly transfers the alkyl group from its substrate, alkylated or benzylated guanine, to a reactive cysteine residue. By attaching the benzyl group to a surface, hAGT fusion proteins immobilize themselves in a specific and covalent manner. The specificity of the reaction of hAGT with its substrate even allows the specific immobilization of hAGT fusion proteins directly out of cell extracts, making the approach an attractive alternative to currently used immobilization procedures.